Summit-ICE Emulator Hardware User's Guide
Contents
1. sese 8 LOCATED DRIVER DIALOG FOR og 9 LOCATED DRIVER DIALOG FOR ON 10 FINISH DIALOG FOR ON 11 THE DEVICE MANAGER ener ener tn nnns 12 RE 10 THE SUMMIT ICE PROPERTIES PAGE eee 13 REH JUMPERS 25s eec ettet eret pe t eie E EE e 15 RE 12 EE 15 RE 13 TERMINATORS CONNECTED TO THE JTAG SIGNALS 17 l Introduction Thank you for purchasing the Summit ICE PCI emulation system The White Mountain DSP Summit ICE Universal Emulator system provides state of the art emulation and support for the Analog Devices JTAG family of DSPs It provides a controlled environment for observing debugging and testing activities in a target system by connecting directly to the target processor through the JTAG interface Features of the Summit ICE system are as follows A A A Plug n Play PCI card Runs with Windows 95 98 and Windows NT Emulation for the industry standard Analog Devices JTAG families of DSPs Rugged high speed JT AG emulation pod 2 Requirements The PC requirements for the Summit ICE are as follows A Pentium 166 or greater A Windows 95 98 or Windows NT 4 0 SP 3 or greater A Minimum of 32 megabytes of PC AT memory A One 32 bit PCI slot 3 Configuration and Installation This section provides all of the information required to install the Summit ICE PCI card and pod into your PC To install the emulator software please refer to your Software User s Guide 3 1 Instal2. 5 1 Connecting To A 5 Volt Target Jumper J1 is used to differentiate between a 3 volt or 5 volt target This is the only jumper that most users will need to change When the jumper is installed the JTAG signals are configured to connect to a 5 volt target When the jumper is installed the LED on the left side is not illuminated 15 3 5 2 Connecting To A 3 Volt Target When the jumper is not installed the JTAG signals are configured to connect to a 3 volt target When the jumper is not installed the LED on the left is illuminated indicating a 3 volt target This is the default setting 3 5 3 Reducing Noise Issues On The J TAG Signals There are three jumpers provided to help reduce problems that may arise because of ringing and reflections on the JTAG signals on the target board The default is that these jumpers are not installed The three jumpers are J2 J3 and J4 Jumpers J2 and J3 are used for adding a parallel terminator on the TDO and CLKIN signals When the jumper is installed a parallel terminator of 120Q and 91Q is connected to the TDO and CLKIN signals Figure 13 shows how the terminator is connected to the JTAG signals It is important to note that the target MUST be able to drive a 51Q load before these jumpers are installed The DSP cannot drive this load directly a driver should be inserted between the JTAG signals on the DSP and the JTAG signals on the header 16 Pod TDO JTAG Controller CLKIN Fig
3. should be displayed Double click White Mountain DSP Summit ICE Select the Resources tab System Properties amp 2 Floppy disk controllers H 6 Hard disk controllers ee Keyboard Monitor 73 Mouse Network adapters 47 Ports COM amp LPT System devices D gt Universal serial bus controller Figure 9 The Device Manager 12 This will display the White Mountain DSP Summit ICE Properties page as shown in figure 10 Here you will find the I O resources allocated to the Summit ICE under the Setting column next to Input Output Range Note the first section of the second I O range listed is the one that should be used when invoking the emulator software i e FCCO This is the base I O address required by the debugger software to access the Summit ICE emulator White Mountain DSP Summit ICE Properties Input Output Range F880 FCCO FCCF Figure 10 The Summit ICE Properties Page 3 3 1 Windows 95 98 Automatic Configuration Override Windows 95 98 may change the I O space on the next insertion removal of the Summit ICE If desired the user may choose 13 to force an I O configuration manually so Windows 95 98 will always use the same I O space This is not recommended as it defeats the purpose of Plug n Play However the user may choose to do so in the following manner 1 Using the above method get into Resources under the Device Manager 2 Remove t
4. 2 January 2000 MANSUMICE Contents 1 INTRODUCTION EE 1 2 REQUIREMENTS EE 2 3 CONFIGURATION AND INSTALLATION w cccssssssssssessssssscssssssssseseees 3 ech INS EAIDIPASEIODN iiie ee es 3 3 2 HARDWARE AND WINDOWS 95 98 DRIVER INSTALLATION 4 3 2 1 WINDOWS 95 INSTALLATION eee 4 3 2 2 WINDOWS 98 INSTALLATION eese nene 6 3 3 HARDWARE CONFIGURATION WINDOWS 95 98 11 3 3 1 WINDOWS 95 98 AUTOMATIC CONFIGURATION OVERRIDE 13 3 4 SOFTWARE INSTALLATION AND 14 3 5 CONFIGURING THE SUMMIT ICE POD eme 14 3 5 1 CONNECTING TO A 5 MOLTTIARGEIT 15 3 5 2 CONNECTING TO A 3 MOLTTIARGEIT 15 3 5 3 REDUCING NOISE ISSUES ON THE JTAG 0 16 3 6 CONNECTING THE POD TO THE SUMMIT ICE BOARD 17 3 7 CONNECTING THE POD TO YOUR TARGET 18 4 SUPPORT adiecto te pide 19 4 1 TECHNICAL 8 0 20 000000000000 0 19 4 2 QUALITY 55 19 5 REFERENCES 20 List of Figures UPDATE DEVICE DRIVER WIZARD FOR 95 5 DRIVER LOCATION DIALOG FOR On 5 ADD NEW HARDWARE WIZARD FOR 98 eese 6 SEARCH FOR HARDWARE DIALOG FOR 98 7 DRIVER SELECTION DIALOG FOR 98
5. Next Add New Hardware Wizard Figure 4 Search for Hardware Dialog for Windows 98 3 Insert your vendor s emulation tools installation CD into the CD ROM drive Windows 98 will ask where to find the Summit ICE driver as shown in figure 5 Click Next Add New Hardware Wizard Figure 5 Driver Selection Dialog for Windows 98 4 Add New Hardware Wizard will locate the SummitICE inf file on the disk as shown in figure 6 Click Next Add New Hardware Wizard Mis List Figure 6 Located Driver Dialog for Windows 98 Add New Hardware Wizard Figure 7 Located Driver Dialog for Windows 98 5 Click Next to install the Summit ICE driver 10 Add New Hardware Wizard Figure 8 Finish Dialog for Windows 98 6 Click Finish and the driver installation is completed as shown in figure 8 3 3 Hardware Configuration Windows 95 98 Windows 95 98 will configure the card automatically The Windows 95 98 PCI drivers will select an available I O space and update the Device Manager and Windows Registry After the card is configured the Device Manager can be checked to see which I O space was assigned to the Summit ICE card To use the Device Manager in Windows 95 98 do the following 1 Click on the Start button 2 Select Settings then Control Panel 11 Double click the System icon Select the Device Manager tab Double click DSP Emulators A window similar to that shown in figure 3
6. Summrit ICE Emulator Hardware User s Guide White Mountain DSP Notice Analog Devices Inc reserves the right to make changes to or to discontinue any product or service identified in this publication without notice Analog Devices assumes no liability for Analog Devices applications assistance customer product design customer software performance or infringement of patents or services described herein In addition Analog Devices shall not be held liable for special collateral incidental or consequential damages in connection with or arising out of the furnishing performance or use of this product Analog Devices products are not intended for use in life support applications devices or systems Use of an Analog Devices product in such applications without the written consent of an Analog Devices officer is prohibited Users are restricted from copying modifying distributing reverse engineering and reverse assembling or reverse compiling the Summit ICE operational software one copy may be made for back up purposes only No part of this document may be reproduced in any form without permission Trademarks are property of their respective holders Limited Warranty The Summit ICE hardware is warranted against defects in materials and workmanship for a period of one year from the date of purchase from Analog Devices or from an authorized dealer Copyright 1999 2000 Analog Devices Inc All rights reserved Revision 1
7. ctivate the Update Device Driver Wizard as shown in figure 1 Update Device Driver Wizard This wizard will complete the installation of PCI Card by searching your local drives network and Internet locations for the most current driver Ifyou have a disk or CD ROM that came with this device insert itnow Itis recommended that you let Windows search for an updated driver To do this click Nextto continue Figure 1 Update Device Driver Wizard for Windows 95 2 Insert your vendor s emulation tools installation CD into the CD ROM drive Windows 95 will then automatically detect and install the Summit ICE driver from the disk as shown in figure 2 Update Device Driver Wizard Windows found the following updated driver for this device White Mountain DSP SummitiCE If you wantto use this driver click Finish this is not the correct driver and you wantto search for a different driver manually click Other Locations Location of Driver Other Locations Figure 2 Driver Location Dialog for Windows 95 3 Click Finish and the driver installation is completed 3 2 2 Windows 98 Installation 1 Power on the PC and start Windows 98 This will activate the Windows 98 Add New Hardware Wizard as shown in figure 3 Click Next Add New Hardware Wizard Figure 3 Add New Hardware Wizard for Windows 98 2 Select Search for the best driver for your device as shown in figure 4 Click
8. he V in the Use automatic settings field by clicking on it 3 Double click the IO setting that you wish to modify and then enter the new base address that you wish to use 4 Check the Conflicting device list if no conflicts are listed select After selecting OK the card will be reconfigured 3 4 Software Installation and Operation To install and operate the debugger software refer to the Software User s Guide included with the software distribution 3 5 Configuring the Summit IC E Pod Important Before the pod is connected to the target system it is important to determine if the target is a 3 volt DSP or 5 volt DSP The factory default setting for the pod is for a 3 volt DSP target Section 3 5 1 explains how to configure the pod for a 5 volt target The Summit ICE pod contains four internal jumpers These jumpers are accessed by removing the four screws on the bottom of the plastic enclosure and removing the top of the enclosure The jumpers are shown in figure 11 The Summit ICE pod also contains two status LED s The LED on the left is for voltage status 3V 5V and the LED 14 on the right is for emulator status The LED s are shown in figure 12 Periodic LED activity on the emulator status LED indicates communication between the target DSPs and emulator Figure 11 Jumpers Box Top Voltage Status Emulator Status Figure 12 LED s 3
9. lation For specific instructions on installing a PCI card into your computer consult the documentation that is provided by the manufacturer of your computer In general you should be able to use the following instructions L Important Summit ICE JTAG emulator contains ESD electrostatic discharge sensitive devices Electrostatic charges readily accumulate on the human body and equipment and can discharge without detection Permanent damage may occur to devices subjected to high energy discharges Proper ESD precautions are recommended to avoid performance degradation or loss of functionality For Windows NT installation instructions of the Summit ICE please refer to your vendor s emulation tools installation guide 3 2 Hardware and Windows 95 98 Driver Installation The Summit ICE requires one PCI slot Configuration of the card is done automatically at boot up due to plug n play hardware support Prior to using your Summit ICE for the first time the Windows 95 98 Driver must first be installed This is accomplished as follows 1 Install the Summit ICE in the PC connect the pod cable to the back of the Summit ICE before applying power to the PC Important Connect disconnect the Ce pod cable to from the Summit ICE card only with the power turned off Failure to follow this precaution may result in damage to the board 3 2 1 Windows 95 Installation 1 Power on the PC and start Windows 95 This will a
10. r 18 4 Support 4 1 Technical Support We fully support all of our products For technical support of the Summit ICE call 603 883 2430 Monday Friday during normal business hours or via e mail at support wmdsp com For direct support of the Analog Devices family of DSPs call the Analog Devices DSP Applications Engineering group at 781 461 3672 4 2 Quality Assurance White Mountain DSP is committed to providing quality products and services In efforts to continually provide this quality please contact our Quality Assurance Department directly if you have any concerns at 603 883 2430 Monday Friday during normal business hours or via e mail at quality 9 wmdsp com Our Quality Assurance Manager will listen to your concerns and provide a timely and effective solution 19 5 References This section discusses other documentation resources you will need to develop your application For information about your development platform refer to your operating system manuals and hardware system manuals For information about digital signal processing theory and application you may which to consult Higgins Digital Signal Processing In VLSI Prentice Hall 1990 Oppenheim and Schafer Digital Signal Processing Prentice Hall 1975 For information on the emulator software refer to the Software Users Guide For information on designing the interface between an Analog Devices JTAG DSP and the emulation header on your cu
11. stom DSP target board refer to Analog Devices JTAG Emulation Technical Reference 2 0 EE68 20
12. ure 13 Terminators Connected To The J TAG Signals Jumper J4 is provided to allow the board level test pins on the JTAG connector BTMS BTCK BTRST and BTDI to be used as ground pins to allow for greater shielding on the JTAG cable connecting the pod to the target These pins should only be used as ground pins if they are not used on your target 3 6 Connecting the Pod to the Summit Ice Board The pod connects to the Summit ICE board through a shielded flat ribbon cable and a 25 pin connector Connect the pod to the Summit ICE before applying power to the PC The JTAG header on the opposite side of the pod can be connected disconnected to a live as well as unpowered target system without damaging the pod system Important Connect disconnect the remote pod to from the emulator card only with the power turned off Failure to follow this precaution may result in damage to the pod or board 17 3 7 Connecting the Pod to Your Target System The pod connects to the target processor through the JT AG interface The target board must be built with an appropriate JTAG connector Please note the position of the key pin The key pin should be used as a guide to connect the pod to the target Included with the Summit ICE system are two extender connectors These extenders are used to connect the Summit ICE system to a target which was designed for use with the ADI ICEPAC These extenders allow connection to the JTAG pins on the ICEPAC heade
Download Pdf Manuals
Related Search