Home

TROUBLESHOOTING

1. 32 Install the wheels See the Wheels and Wheel Hubs topic for more information Fill the master cylinder reservoir with brake fluid and bleed the brakes See the Brake Fluid topic for more information Make sure the brakes work properly before riding 9 41 Burnishing New Brake Pads Warning Failure to properly burnish the brake pads could lead to premature brake pad wear or brake loss Brake loss can result in severe injury Brake pads both main and auxiliary must be burnished to achieve full braking effectiveness Braking distance will be extended until brake pads are properly burnished To properly burnish the brake pads use the following procedure 1 Choose an area large enough to safely accelerate the ATV to 30 mph and to brake to a stop 2 Accelerate to 30 mph then compress brake lever or apply the auxiliary brake to decelerate to 0 5 mph 3 Repeat procedure on each brake system five times 4 Adjust the auxiliary brake if necessary 5 Verify that the brake light illuminates when the hand lever is compressed or the brake pedal is depressed 9 42 KYMCO MXU 500i 700i Repair Manual Brake System gt Rear Brake Calipers Rear Brake Calipers SAFETY FIRST Protective gloves and eyewear are recommended at this point NOTE Brake fluid is a corrosive chemical and can damage paints and some plastics Avoid contact with skin There are two rear brake calipers The caliper that mounts to the top of the f
2. and can damage paint chrome and plastic Wipe up any spills immediately Note The master cylinders can not be repaired Replace the assembly with a new one if needed Removal Brake Light Switches Disconnect the rear brake light switch connectors from the switch on the left master cylinder 9 67 To remove the left master cylinder brake light switch take out the screw with a 2 Phillips screwdriver E The right side front brake master cylinder has a different style brake switch 9 68 Compress the tabs and remove the switch from the master cylinder Reservoir Caps Remove the reservoir cap screws with a 2 Phillips screwdriver 9 69 Lift off the reservoir cap Remove the rubber diaphragm 9 70 Master Cylinders lf the brake hoses are to be disconnected drain the brake fluid See the Brake Fluid topic for more information Remove the brake hose banjo bolt and the two sealing washers eyel HEOIR SOM eyoleaprytA ou pl Loosen the brake master cylinder perch bolts with an 8 mm socket Free the perch from the handlebar and remove the master cylinder ord Brake Levers Hold the pivot bolt with a 10 mm socket and loosen the pivot nut with a 10 mm socket Remove the nut and bolt Free the brake lever from the master cylinder Installation Note Do not splash brake fluid onto any rubber plastic and coated parts When working with brake fluid use shop towels to cover
3. 9 9 KYMCO MXU 500i 700i Repair Manual Brake System gt Brake Pedal Brake Pedal and Master Cylinder SAFETY FIRST Protective gloves and eyewear are recommended at this point NOTE Brake fluid is a corrosive chemical and can damage paints and some plastics Avoid contact with skin There are two rear brake calipers The caliper that mounts to the top of the final drive gear is connected to the pedal activated master cylinder The caliper that mounts to the side of the final drive gear is connected to the left handlebar master cylinder Removal Remove the right mudguard See the Mudguards and Footrests topic for more information The brake pedal is mounted to a pivot on the right side of the frame 9 10 Drain the brake fluid from the brake pedal master cylinder system if the master cylinder is to be disconnected from the brake hose See the Brake Fluid topic for more information 9 11 th ol i Remove the master cylinder reservoir mounting bolt with a 3 Phillips screwdriver Remove the two brake pedal pivot mounting bolts 9 12 WMH eren gt A Loosen the brake hose banjo bolt with a 12 mm socket Remove the banjo bolt and the two sealing washers Remove the two master cylinder mounting bracket nuts with a 12 mm socket Remove the pedal and master cylinder assembly from the frame 9 13 Disassembly Remove the master cylinder rod cotter pin washer and pivot pi
4. KYMCO MXU 500i 700i Repair Manual Brake System 9 Brake System This chapter covers the location and servicing of the front brake components for the KYMCO MXU 700i and MXU 500i models 1 Brak DISCS sicsssiuusdeen aaaea 9 3 2 BraIKERCdar zaneo 9 10 S FFONt Brake Calipers sisisi aeaa 9 30 4A Rear Brake Calipers ssn a RA 9 43 5 MaSter CylNnOGrs svice a T a ETG 9 67 TROUBLESHOOTING Loose brake lever e Airin hydraulic brake system e Brake fluid level too low e Hydraulic brake system leakage Tight brake lever e Seized piston e Clogged hydraulic brake system e Smooth or worn brake pad 9 1 Poor brake performance Air in brake system Deteriorated brake fluid Contaminated brake pads and brake disk Worn brake pads Worn brake master cylinder piston oil seal Clogged brake fluid line Deformed brake disk Unevenly worn brake pad Brake noise Contaminated brake pad surface Excessive brake disk run out Incorrectly installed caliper Brake disk or wheel not aligned Hard braking Seized hydraulic brake system Seized piston 9 2 KYMCO MXU 500i 700i Repair Manual Brake System gt Brake Discs Brake Discs SAFETY FIRST Protective gloves and eyewear are recommended at this point Inspection Remove the wheels See the Wheels and Wheel Hubs topic for more information Check the brake discs for damage or excessive wear Using a dial gauge and stand measure the disc brake runout Replace the front di
5. and a i ey a r iz Sie i Remove the dust seal from the caliper bore and discard Use a mechanics pick to remove the piston fluid seal from the caliper bore and discard 9 36 Inspection Check the brake caliper bore for any scratches damage or excessive wear Clean the brake caliper bore with DOT 4 brake fluid Do not dry off with a rag CYCLEPEDIA COM Check the piston for any scratches damage or excessive wear Clean the piston with DOT 4 brake fluid Do not dry off with a rag 9 37 Assembly EE Install a new piston fluid seal into the inner groove Install a new dust seal into the outer groove in the caliper bore Install the piston into the caliper bore closed end first Push the piston all the way in 9 38 hd Install the pin boots into the caliper Apply silicone grease to the caliper bracket pins Install the caliper bracket 9 39 Installation h Fit the brake caliper into place Guide the brake disc between the pads 9 40 Install the two brake caliper mounting bolts and tighten them to specification TORQUE THREAD SIZE AND TYPE CALIPER AND FR RR KNUCKLE M8 X 1 25 2 4 3 2 24 32 Connect the brake hose to the caliper if it was removed Use a new sealing washer on each side of the hose fitting Tighten the banjo bolt to specification TORQUE THREAD SIZE AND TYPE FRONT REAR CALIPER AND BRAKE HOSE END M10 X 1 25 2 4 3 2 24
6. d 9 62 Use a mechanics pick to remove the piston fluid seal from the caliper bore and discard Inspection Check the brake caliper bore for any scratches damage or excessive wear Clean the brake caliper bore with DOT 4 brake fluid 9 63 CYCLEPEDIA COM Check the piston for any scratches damage or excessive wear Clean the piston with DOT 4 brake fluid Assembly Coat the new seals piston and piston bore with DOT 4 brake fluid Install a new piston fluid seal into the inner groove Install a new dust seal into the caliper Install the piston into the caliper bore with the open end facing out 9 64 9 65 Fit the brake caliper into place Guide the brake disc between the pads Install the two brake calipers mounting bolts B and tighten them to specification with a 12mm socket Install new sealing washers and tighten the brake hose banjo bolt A to specification with a 12 mm socket Torque Item Thread dia mm Rear disc holder and gear box Kgf m N m ft lb 4 5 45 34 Brake hose oil bolt 3 5 35 25 Fill the master cylinder reservoir with brake fluid and bleed the brakes See the Brake Fluid topic for more information Make sure the brakes work properly before riding 9 66 KYMCO MXU 500i 700i Repair Manual Brake System gt Master Cylinders Master Cylinders SAFETY FIRST Protective gloves and eyewear are recommended at this point Warning Brake fluid is very caustic
7. d teen rua to specification with a 12 mm socket Tighten the pad pins A to specification with a 5 mm Allen wrench Install new sealing washers and tighten the brake hose banjo bolt B to specification with a 12 mm socket Torque Item Thread dia mm Kgf m N m ft lb Rear disc Rear disc holder and gearbox and gear box Rear disc holder and gearbox 10 4 5 45 34 Brake pad mounting pin o 1 8 18 13 Brake hose oil bolt 3 5 35 25 9 57 Top Caliper Removal lf the brake caliper is to be disassembled drain the brake fluid Brake Fluid and remove the banjo bolt A with a 12 mm socket Remove the two brake caliper mounting bolts B with a 12 mm socket 9 58 Brake Pad Replacement Remove the brake pads 9 59 CYCLEPEDIA COM Discard the brake pads if the linings are below 1 mm or 0 039 in thick Disassembly Remove the caliper bracket Inspect the caliper bracket O rings and replace them as needed 9 60 T Pa i Remove the rubber boots Replace if damaged NOTE Always wear safety glasses when using compressed air and never point it directly at yourself or anyone else cor Place a thick rag over caliper piston and use compressed air to move the piston out Do not place your fingers over the caliper piston while removing it as serious injury could result 9 61 ae _ Remove the caliper piston by hand Remove the dust seal from the caliper bore and discar
8. fluid if the caliper is to be completely removed and disassembled See the Brake Fluid topic for more information Note If you are only replacing the brake pads it is not necessary to drain the brake fluid 9 30 h Remove the brake caliper from the knuckle and disc Note Do not use the front brake while the caliper and brake pads are not installed on the vehicle 9 31 Brake Pad Replacement Push the pads and bracket in towards the caliper piston Remove the brake pads CYCLEPEDIA COM Discard the brake pads if the linings are below 1 mm or 0 039 in thick Install the brake pads See the Installation section for more information 9 32 Disassembly Loosen the brake hose banjo bolt with a 12 mm socket Remove the banjo bolt and sealing washers Place the end of the brake hose in a suitable container to container to collect any dripping brake fluid 9 33 Remove the caliper bracket Inspect the caliper bracket O rings and replace them as needed NOTE Always wear safety glasses when using compressed air and never point it directly at yourself or anyone else Remove the pin boots from the caliper r F Z 9 34 Place a thick rag over caliper piston and use compressed air to move the piston out Do not place your fingers over the caliper piston while removing it as serious injury could result r t 7 F B i z b Son ae a CYCLEPEDIA COM Remove the caliper piston by h
9. he caliper piston by hand 9 49 i F at A Remove the dust seal from the outer caliper bore and discard Use a mechanics pick to remove the piston seal from the inner caliper bore and discard 9 50 Inspection Check the brake caliper bore for any scratches damage or excessive wear Clean the brake caliper bore with DOT 4 brake fluid CYCLEPEDIA COM 9 51 Check the piston for any scratches damage or excessive wear Clean the piston with DOT 4 brake fluid Check the brake caliper holder for damage 9 52 Assembly Coat the new seals piston and piston bore with DOT 4 brake fluid j 73 a el i i TEE z Install a new piston seal into the inner caliper bore groove Install the dust seal into the outer groove 9 53 AF s tara Install the piston into the caliper so that the open end faces out Push the piston all the way in C s CA ae fka n _ a a a a A Install the brake pad spring 9 54 Apply silicone grease to the caliper bracket pins Install the caliper bracket Brake Pad Installation Install the inner brake pad and then the outer brake pad 9 55 Install the two the brake pad mounting pins into the caliper and through the brake pads Installation Fit the brake caliper into place on the final drive gear case and guide the disc between the pads 9 56 Install the two brake calipers mounting bolts C ui
10. inal drive gear is connected to the pedal activated master cylinder The caliper that mounts to the side of the final drive gear is connected to the left handlebar master cylinder 9 43 Side Caliper Removal lf the brake pads are going to be removed go ahead and loosen the pad pins A with a 5 mm Allen If the brake caliper is to be disassembled drain the brake fluid Brake Fluid and remove the banjo bolt B with a 12 mm socket Remove the two brake caliper mounting bolts C with a 12 mm socket 9 44 Remove the side brake caliper from the final drive gear Brake Pad Replacement Remove the brake pad pins with a 5 mm Allen 9 45 CYCLEPEDIA cCOM CYCLEPEDIA COM Replace the brake pads if the wear indicators are worn away 9 46 Disassembly Remove the brake hose banjo bolt with a 12 mm socket Remove the banjo bolt and sealing washers CYCLEPEDIA CON Remove the caliper bracket 9 47 Remove the rubber boots Replace if damaged Remove the brake pad spring NOTE Always wear safety glasses when using compressed air and never point it directly at yourself or anyone else 9 48 aa s T Y Te j i _ 7 a n f 4 E t i E l a O Place a thick rag over caliper piston and use compressed air to move the piston out Do not place your fingers over the caliper piston while removing it as serious injury could result Remove t
11. master cylinder mounting bracket nuts with a 12 mm socket and tighten them securely Connect the brake hose to the master cylinder Use a new sealing washer to each side of the banjo bolt Tighten the brake hose banjo bolt to specification with a 12 mm socket Torque Item Thread dia mm Kgf m N m ft lb Brake hose oil bolt 3 5 35 25 9 27 ss ee ay ral a B 2 a ey r M a E T Py i F r i a k 1 i 1 i aF ii Fir the reservoir into place and install the mounting bolt Tighten the bolt securely with a 3 Phillips screwdriver 9 28 Plug in the rear brake light switch connector Fill the rear brake system with brake fluid and bleed out the air See the Brake Fluid topic for more information Adjust the rear brake pedal and brake light switch See the Brake Fluid topic for more information Install the right mudguard See the Mudguards and Footrests topic for more information 9 29 KYMCO MXU 500i 700i Repair Manual Brake System gt Front Brake Calipers Front Brake Calipers SAFETY FIRST Protective gloves and eyewear are recommended at this point Warning Brake fluid is very caustic and can damage paint chrome and plastic Wipe up any spills immediately There are three brake calipers two for the front and one with the left rear wheel hub Removal Remove the front wheels or left rear wheel as needed See the Wheels and Wheel Hubs topic for more information Drain the brake
12. mponents are damaged Assembly Clean the master cylinder components with fresh brake fluid DOT 4 CYCLEPEDIA Lubricate the piston and seals with fresh brake fluid Insert the spring and piston into the master cylinder 9 20 Install the rubber cover over the piston 9 21 Install the reservoir pipe with an O ring in good condition Install the snap ring into its groove with snap ring pliers Place washers on each side of the master cylinder lever 9 22 Apply a light coat of waterproof grease to the pivot bolt Install the pivot bolt and nut and tighten them securely 9 23 EP a TTT E nak i V NT CYCLEPEDIA Install the bracket to the master cylinder and tighten the two bolts securely Use a spring puller to install the pedal return spring and rear brake light switch spring as shown ATTY TTT ahaha Connect the reservoir hose to the pipe and secure it with the clamp 9 24 Apply a light coat of waterproof grease to the pedal pivot Fit the pedal onto the pivot Install the washer and a new cotter pin Bend the pin as shown to secure the pedal and washer 9 25 Connect the brake rod to the pedal and lever Install the joints washers and new cotter pins Bend the cotter pins to secure the rod Installation a gt 7 A i _ e J af Fit the master cylinder and pedal into place on the right side of the frame 9 26 m Install the two
13. n Separate the master cylinder rod from the brake pedal 9 14 To remove the pedal from the bracket take out the cotter pin and remove the washer Slide the pedal off of its pivot TTT LL hkaaaeeael ETT To remove the reservoir hose slide up the clamp and free the hose form the master cylinder To free the master cylinder from the bracket remove the two mounting bolts with a 10 mm socket 9 15 E a svovhonnee eee lt Mae E Use a spring puller to remove the pedal return spring and rear brake light switch spring To remove the master cylinder lever hold the bolt and loosen the nut Remove the nut and bolt 9 16 fa d b a _Y Take care to keep track of the washers that sit on each side of the lever 9 17 Remove the reservoir pipe snap ring with snap ring pliers Lift out the reservoir pipe Inspect the O ring and replace it as needed T3 il k a ee it DR an Remove the rubber cover from the master cylinder piston 9 18 h iis s E i j MENON aR Remove the snap ring using a pair of internal snap ring pliers Use a suitable tool to hold back the piston as it can spring out NCYCLEPEDIA COM Remove the piston and spring from the master cylinder 9 19 e ee le Inspect the piston seals and master cylinder bore for wear and damage Replace the master cylinder an assembly if the co
14. scs as a Set if any are out of the service limit 9 3 Measure the brake disc thickness with a micrometer Replace the rotor if it is below the service limit Brake disk thickness FR 4 0 0 156 RR 5 0 0 195 FR 3 0 12 RR 4 0 156 Removal Front CYCLEPEDLA CON EE To remove the brake disc take out the four disc brake bolts with a Torx socket wrench Separate the disc brake from the wheel hub 9 4 Rear Remove the rear final drive See the Rear Final Drive Gear topic for more information 9 5 GY BEREDI cow Remove the five rear brake disc bolts with a 6 mm Allen socket Remove the rear brake disc from the brake disc holder 9 6 Installation Front Install the disc brake onto the wheel hub Tighten the four bolts to specification with a Torx socket Torque Item Thread dia mm Kgf m N m ft lb Front brake disc and front hub 6 2 0 20 14 Install the front wheels See the Wheels and Wheel Hubs topic for more information Check the function of the brakes before riding 9 7 Rear te i 9 8 Install the five rear brake disc mounting bolts and tighten them to specification with a 6 mm Allen socket Torque Thread dia mm Kgf m N m ft lb Rear brake disc and rear hub PB 3 5 35 25 Install the rear final drive gear case See the Rear Final Drive Gear topic for more information
15. these parts 9 72 Brake Levers Apply a light coat of waterproof grease to the pivot section of the brake lever pivot bolts Fit the brake lever into place Insert the pivot bolt from above and snug it down Thread on the nut and tighten it securely while holding the bolt from turning Make sure the lever moves smoothly 9 73 Master Cylinders SfSLAPZULLoCOL Fit the master cylinder perch into place on the handlebar Install the two mounting bolts and tighten them to specification with an 8 mm socket Torque Item Thread dia mm Kgf m N m ft lb 1 2 12 7 CYCLEPZDIA COM Connect the brake hose to the master cylinder Use new sealing washers to each side of the hose fittings Tighten the banjo bolt to specification 9 74 Torque Item Thread dia mm Kgf m N m ft lb Master cylinder holder bolt e 1 2 12 7 Secondary master cylinder holder and e 1 2 12 7 When all the brake hoses are connected fill the master cylinders with fresh brake fluid from a tightly sealed container and bleed the brakes See the Brake Fluid topic for more information Make sure the brakes work properly before riding Reservoir Caps Install the rubber diaphragm compressed and the cap 9 75 Install the reservoir cap screws and tighten them to specification with a 2 Phillips screwdriver Torque Item Thread dia mm Kgf m N m ft lb Master cylinder cap screw 0 15 1 5 1 1 Make s
16. ure the brakes work properly before riding 9 76 Brake Light Switches Install the left master cylinder brake light switch Tighten the screw securely with a 2 Phillips screwdriver FAPT ia gt P ins Plug in the rear brake light switch connectors to the switch on the left master cylinder 9 77 Insert the right master cylinder brake light switch and be sure it locks into place 9 78

TROUBLESHOOTING

Contents

Download Pdf Manuals

Related Search

Related Contents