OPERATING INSTRUCTIONS
Contents
1. Each time the gt button is pressed the set time increases by 1 minute and each time hel a but ton is pressed the set time decreases by 1 minute Pressing those buttons longer increases decreases the set time by 10 minutes H Press the CLOCK set button again and close the front lid When a button of the remote controller is pressed all displays appear on the screen and then disappear immediately Do not use manganese batteries The remote controller could malfunction The service life of an alkaline battery is about 1 year However a battery whose time limit is approaching may be exhausted soon The recommended usable time limit is indicated month year on the bottom of the battery To prevent liquid leakage take out all batteries when the remote controller is not going to be used for a long time CAUTION If liquid from the batteries gets onto your skin or clothes wash it well with clean water If liquid from the batteries gets into your eyes wash them well with clean water and consult a doctor at once Do not use rechargeable batteries Replace the 2 batteries with new ones of the same type Dispose of exhausted batteries in the correct manner The operation mode is indicated by the Opera tion Indicator lamp on the indoor unit as following figure Operation Indicator lamp skies EMERGENCY COOL ers sure EMERGENCY HEAT Pras STOP2. EE Air filter DN Remove A CAUTION When the air filter is to be removed do not touch the metal parts of the indoor unit This may cause an injury E Remove dirt from the air filter using a vacuum cleaner or by washing the filter with water Do not wash with scrubbing brush or hard surface of sponge Otherwise the filter may deform If the dirt is noticeable wash the filter with a solution of mild detergent diluted in lukewarm water If hot water 50 C or more is used the filter may be deformed El After washing with water lukewarm water dry the air filter well in the shade Do not expose the air filter to direct sunlight or heat from a fire when drying it ER install the air filter Securely install its tabs EE N Install panel with a scrubbing brush or the hard surface of a sponge Do not soak the front panel in water lukewarm water longer than two hours and do not expose the panel to direct sunlight heat or flames when drying it The panel may be deformed or discolored H Hold both ends of the front panel keep the panel level and insert the hinges into the holes on the upper part of the indoor unit until they click into place Then close the front panel securely and press the three positions on the front panel as indicated by the arrows Ae Aer Je Less Optional product is available from your local dealer NOTE The QUICK CLEAN KIT can only be fit
3. Inspection and maintenance When the air conditioner is used for several seasons the capacity may be lowered due to dirt inside the unit Depending on the condition an odor may be generated or dehumidified water may not drain out smoothly due to dirt dust etc It is recommended that the unit be inspected and maintained charged by specialist in addition to normal maintenance Consult your dealer Operating sound considerations Do not put an object around the air outlet of the outdoor unit This may lower the capacity or increase the volume of the operating sound If an abnormal sound is heard during operation consult your dealer Relocation When the air conditioner is to be removed or re installed because of rebuilding moving etc special techniques and work are required Z WARNING Repairs or relocation should not be done by the customer If this is done incorrectly it may cause a fire an electric shock or an injury from the unit falling water leaking etc Consult your dealer Disposal To dispose of this product consult your dealer H you have any questions consult your dealer Model Set name MSZ GB50VA Indoor MSZ GB50VA Outdoor MUZ GB50VA Function Power supply N 230V 50Hz Capacity Input Weight Indoor Outdoor Refrigerant filli ng capacity R410A IP code Indoor Outdoor Permissible excessive operat
4. e Para utilizar esta unidade correctamente certifique se de que l estas instru es de opera o antes da utiliza o BRUGSANVISNING Til kunden e L s denne brugsanvisning f r brugen s korrekt og forsvarlig anvendelse af klimaanl gget sikres BRUKSANVISNING F r kunder e F r att anv nda enheten p r tt och s kert s tt ska denna bruksanvisning l sas innan enheten tas i bruk LETME TAL MATLARI Sat n al c lar i in e Bu birimi do ru ve g venli olarak al t rmak i talimatlar n mutlaka okuyun in kullanmadan nce bu i etme PYKOBOACTBO NO KCNMNYATAUNN Dna nonbsoBaTenen e na o ecneuenuug NpaBunbHoro n 6esonacHoro vcnonbsoBaHnA npn opa cnenyeT DO Hayana ero gKkcnnyaTaynn BHNMATENbHO NPOUUTaTb DAHHOE PYKOBOACTBO Frangais Nederlands EAAnvika Portugu s Svenska Tiirkge Pyccxun CONTENTS SAFETY PRECAUTIONS NAME OF EACH PART SS PREPARATION BEFORE OPERATION AUTO CHANGEOVER AUTO MODE OPERATION MANUAL OPERATION COOL DRY HEAT AIR FLOW VELOCITY AND DIRECTION ADJUSTMENT ECONO COOL OPERATION TIMER OPERATION ON OFF TIMER WHEN THE AIR CONDITIONER IS NOT GOING TO BE USED FOR ALONG TIME MAINTENANCE CLEANING THE FRONT PANEL HEAT EXCHANGER AND FAN CLEANING THE AIR FILTER CATECHIN CLEANING THE AIR CLEANING FILTER OPTION REPLACEMENT OF THE AIR CLEANING FILTER OPTION CLEANING THE A
5. TOO zin TOO WARM COOL a ON OFF E To change the AIR FLOW blowing direction vertically press the i e e e VANE button MODE FAN sTOP After the operation mode is set once the operation starts in the same mode as Is the one set previously from the next time by simply pressing the button 1 Each time the button is pressed the angle of the horizontal vane is changed ECONOCOOL VANE START MODE FAN sTOP in sequence 1 2 gt 4 3 3 4 4 5 SWING gt AUTO Geo EE ca Se cau SWING OPERATION 2 Use the swing operation for the air flow to reach all corners of the room TIME RESET CLOCK E TIME Recommended horizontal vane range SS for more efficient air conditioning Use the AUTO position usually SCHOOSSHSHSHHSSHHHSHSHSHHHSHSHSHSHSHSHSHOHHSSHHSHSHSHOHHEHSHSOHSESHSHOSEEEE Sou one Be eee aa vioan E When the set temperature is to be changed use positions 2 to a 4 in the HEAT mode when A9 adjusting to your requirements Press the Di button to lower the temperature One press lowers the temperature by about 1 C Press the 6 button to raise the temperature One press raises the temperature by about 1 C In COOL operation When the outside temperature is low the fan of the outdoor unit turns on and off frequently or decreases the rotation speed to maintain sufficient cooling capacity In DRY operation T
6. 2 AUTO mode by pressing the ME button at restart and starts operation again ses Each time this button is pressed the operation mode is changed in sequence AUTO gt 4 COOL gt DRY gt HEAT ON OFF WARM GSS The set temperature is also displayed on the remote controller Information for multi system air conditioner e Multi system air conditioner can connect two or more indoor units with one outdoor unit According to the EE To stop operation capacity two or more units can operate simultaneously ONOFF When you try to operate two or more indoor units with one outdoor unit simultaneously one for the cooling and the MODE FAN STOP E Press the button other for heating the operation mode of the indoor unit that operates earlier is selected The other indoor units that will After the operation mode is set once the operation starts in the same mode as start the operation later cannot operate indicating an operation state Refer to the table of Operation Indicator lamp ECONO COOL VANE START the one set previously from the next time by simply pressing the button below a In this case please set all the indoor units to the same operation mode When indoor unit starts the operation while the defrosting of outdoor unit is being done it takes a few minutes max gt 10 minutes to blow out the warm air TIME Inthe heating operation the indoor unit that does not operate may get warm or the sound of refrigerant flowi
7. C or less om temperature NOTE If two or more indoor units are operating in multi system there might be a case that the indoor unit which is This shows a state of standby for operation operating in AUTO cannot change over to the other operating mode COOL lt gt HEAT and becomes a state Please refer to Information for multi system air conditioner of standby Refer to the detailed information for multi system air conditioner explained on the right above MANUAL OPERATION COOL DRY HEAT AIR FLOW VELOCITY AND DIRECTION ADJUSTMENT To select the COOL DRY or HEAT mode AIR FLOW velocity and direction can be selected as required ONOFF e E ES Press the cn button P To change the AIR FLOW velocity press the zs button MODE S Each time the button is pressed the fan speed is changed in sequence E Select the operation mode by pressing the button p p 9 q r g e A 7 A a Low a Med aat High aati Super High AUTO Each time this button is pressed the operation mode is changed in sequence AUTO gt t COOL DRY gt HEAT To stop operation ONOFF Press the button aa MITSUBISHI ELECTRIC ata MITSUBISHI ELECTRIC Use the sati Super High notch to cool heat the room more efficiently If the operating sound of the air conditioner disturbs your sleep use the a Low notch ON OFF dERADAES
8. Mitsubishi Electric producten zijn ontwikkeld en gefabriceerd uit eerste kwaliteit materialen De onderdelen kunnen worden gerecycled en worden hergebruikt Het symbool betekent dat de elektrische en elektronische onderdelen op het einde van de gebruiksduur gescheiden van het huishoudelijk afval moeten worden ingezameld Breng deze apparatuur dan naar het gemeentelijke afvalinzamelingspunt In de Europese Unie worden elektrische en elektronische producten afzonderlijk ingezameld Help ons mee het milieu te beschermen Espa ol Su producto MITSUBISHI ELECTRIC est dise ado y fabricado con materiales y componentes de alta calidad que pueden ser reciclados y reutilizados Este s mbolo significa que el aparato el ctrico y electr nico al final de su ciclo de vida se debe tirar separadamente del resto de sus residuos dom sticos Por favor deposite este aparato en el centro de recogida reciclado de residuos de su comunidad local cuando quiera tirarlo En la Uni n Europea existen sistemas de recogida espec ficos para productos el ctricos y electr nicos usados i Ay denos a conservar el medio ambiente Italiano Questo prodotto MITSUBISHI ELECTRIC stato fabbricato con materiali e componenti di alta qualit che possono essere riciclati e riutilizzati Questo simbolo significa che i prodotti elettrici ed elettronici devono essere smaltiti separatamente dai rifiuti casalinghi alla fine della loro vita di servizio Per disfarsi di que
9. cleaning EJ Clean the air outlet and fan of the indoor unit Make sure the fan has stopped A Switch the indoor unit off with the remote controller and disconnect the power supply Q plug and or turn off the breaker otherwise you may get injured since the fan of the indoor unit rotates at high speed during operation Be careful not to injure your hands If the air outlet or fan is dirty moldy or dusty clean with a wet or dry soft cloth or with the brush of QUICK CLEAN KIT which is installed to a vacuum cleaner If the dirt is noticeable around the air outlet clean with a cloth soaked in a Please refer to the instructions described in QUICK CLEAN KIT for the details of the way to clean with the brush of Manually move the horizontal vane to the end towards you and make sure the fan has stopped QUICK CLEAN KIT Do not use gasoline benzine and polishing powder Do not use excessive force to the fan Otherwise it may be cracked Put the vertical vanes back to their original positions one by one Hold the tab of each vertical vane and insert the Push each vertical vane until it clicks into place vertical vanes into their respective grooves E Remove the horizontal vane Be sure to hold horizontal vane when unlocking the stoppers Follow the procedure CU and to remove the horizontal vane Groove Be sure to hold the tabs to install the vertical vanes otherwise the vanes can be da
10. controller and is turned on again the air conditioner will start operation automati cally in the same mode as the one set with the remote controller just before the shutoff of the main power INSTALLATION RELOCATION AND INSPECTION The installation location of the outdoor unit should be at least 3 m away from the antennas for TV sets radios ete In areas where the reception is weak provide greater space between the outdoor unit and the antenna of the affected device if operation of the air conditioner interferes with radio Installation place Avoid installing the air conditioner in the following places Where flammable gas could leak Z CAUTION Inverter type To prevent the effects fluorescent lamp or TV reception of a fluorescent lamp keep as far apart as possible Well ventilated dry pl Do not install the unit where flammable gas could leak enges ae If gas leaks and collects around the unit it may cause picture D distortion or an explosion f f the noise 100 mm or Jo Where there is much machine oil more 200 mm or more Salty places such as the seaside Where sulfide gas is generated such as a hot spring Where oil is splashed or where the area is filled with oily smoke Where there is high frequency or wireless equipment J Z WARNING If the air conditioner operates but does not cool or h
11. favor ajude nos a conservar o ambiente em que vivemos Dansk Dit produkt fra MITSUBISHI ELECTRIC er designet og fremstillet med kvalitetsmaterialer og komponenter der kan genbruges Dette symbol viser at elektrisk eller elektronisk udstyr ikke m bortskaffes sammen med almindeligt husholdningsaffald efter endt levetid Bortskaf dette udstyr p en lokal genbrugsplads EU er der s rskilte indsamlingsordninger for elektriske og elektroniske produkter Hj lp os med at bevare det milj vi lever i Svenska Denna produkt fr n MITSUBISHI ELECTRIC r designad och tillverkad av material och komponenter med h g kvalitet som kan tervinnas och teranv ndas Denna symbol betyder att elektriska och elektroniska produkter efter slutanv ndande skall sorteras och hanteras separat fr n Ditt hush llsavfall Var sn ll och l mna denna produkt hos Din lokala mottagningstation f r avfall och tervinning Inom den Europeiska Unionen finns det separata insamlingssystem f r begagnade elektriska och elektroniska produkter Var sn ll och hj lp oss att bevara milj n vi lever i T rk e Bu sembol i areti sadece AB lkeleri i indir Bu sembol i areti direktif 2002 96 EC Madde 10 Kullan c bilgileri ve Ek IV e tabidir Pycckn Daun cumBon npuMeHAeTCA TONbKO B CTpaHax EC Dauupun cumBon cooTBeTCcTByeT AupekTuBe CTatbu 10 EC 2002 96 UHcbopmauna gna nonb3oBatenen n Mpnnoxenno IV 157 This product is designed and inten
12. indoor unit The cool air from the air conditioner rapidly cools moisture in the air inside the room and it turns into mist Mechanical sound is heard from the indoor unit This is the switching sound in turning on off the fan or the compressor The swing operation of the HORIZONTAL VANE is suspended for about 15 seconds then restarted This is for the swing operation of the HORIZON TAL VANE to be performed normally The air flow direction changes during operation The direction of the horizontal vane cannot be adjusted with the remote controller When the air conditioner is operated in COOL or DRY mode if the operation continues with air blowing down for 1 hour the direction of the air flow is automatically set to position 1 to prevent condensed water from dropping In the heating operation if the air flow tempera ture is too low or when defrosting is being done the horizontal vane position is automatically set to horizontal Water leaks from the outdoor unit During COOL and DRY operations pipe or pipe connecting sections are cooled and this causes water to condense Inthe heating operation the defrosting operation makes water frozen on the outdoor unit melt and drip down In the heating operation water drips from the heat exchanger This is not a malfunction However if you have any trouble with water dripping consult your dealer for drainage work Please note that we canno
13. the unit only Do not use other remote controller This diagram shows an overall view 1 ge el T ter ON OFF dERAD ER C Fan speed control button Operation select button ECONO COOL button MODE FAN sTOP CONO COOL VANE OSTART Off timer button On timer button TIME set buttons Forward button Backward button CLOCK set button Vane control button RESET button PREPARATION BEFORE OPERATION Auto restart function These models are equipped with an auto restart function If you do not want to use this function please consult the service representative because the setting of the unit needs to be changed Auto restart function is When the indoor unit is controlled with the remote controller the operation mode the set temperature and the fan speed are stored in the memory If a power failure occurs or the main power is turned off during operation Auto restart function sets automatically to start operating in the same mode as the one set with the remote controller just before the shutoff of the main power Refer to page 6 for details Indoor and or Outdoor unit Insert the power supply plug into the power outlet and or turn the breaker on A WARNING Remove dirt from the power supply plug and insert the plug securely If dirt adheres to the plug or insertion is incomplete it may cause a fire or a
14. the vertical vanes otherwise the vanes can be damaged Do not use excessive force to the fan guard during this procedure The fan guard may be deformed and the vanes may not work properly BEFORE CONTACTING THE SERVICE REPRE SENTATIVE CHECK THE FOLLOWING AGAIN Question Check points Is the breaker turned on Is the fuse blown Is the ON timer set Page 9 The air conditioner cannot be operated All LED lamps on the indoor unit are blinking Is the horizontal vane attached to the indoor unit correctly Page 12 The horizontal vane does not move Are the horizontal vane and the vertical vane attached to the indoor unit correctly Page 12 Is the fan guard deformed The room cannot be cooled or heated sufficiently Is the temperature setting correct Page 7 Is the filter clean Page 10 Is the fan of the indoor unit clean Page 12 Are there any obstacles blocking the air inlet or outlet of the indoor or outdoor unit Is a window or door open The air from the indoor unit smells strange Is the filter clean Page 10 Is the fan of the indoor unit clean Page 10 The display on the remote controller does not appear or it is dim The indoor unit does not respond to the remote control signal Are the batteries exhausted Page 5 Is the polarity of the batteries correct Page 5 Are any buttons on the remote controller of other electric a
15. wait Cracking sound is heard This sound is generated by the expansion con traction of the front panel etc due to change in temperature The air from the indoor unit smells strange The air conditioner may suck in an odor adhering to the wall carpet furniture cloth etc and blow it out with the air The fan of the outdoor unit does not rotate even though the compressor is running Even if the fan starts to rotate it stops soon When the outside temperature is low the fan may not operate to maintain sufficient cooling capacity The sound of water flowing is heard This is the sound of refrigerant flowing inside the air conditioner This is the sound of condensed water flowing in the heat exchanger This is the sound of the heat exchanger defrost ing The sound as burbling is heard This sound is heard when the outside air is absorbed from the drain hose in turning on the range hood or the ventilation fan and that makes water flowing in the drain hose spout out This sound is also heard when the outside air blows into the drain hose in case the outside wind is strong The room cannot be cooled sufficiently When a ventilation fan or a gas cooker is used in a room the cooling load increases resulting in an insufficient cooling effect When the outside air temperature is high the cooling effect may not be sufficient Mist is discharged from the air outlet of the
16. A MITSUBISHI AVM ELECTRIC SPLIT TYPE AIR CONDITIONERS OPERATING INSTRUCTIONS INDOOR UNIT MSZ GB50VA CE OPERATING INSTRUCTIONS For customers e To use this unit correctly and safely be sure to re before use ad this operating instructions Bedienungsanleitung Fur Kunden e Um diese Einheit richtig und sicher zu verwenden unbedingt diese Bedienung sanleitung vor der Inbetriebnahme durchlesen NOTICE D UTILISATION A lattention des clients e Pour avoir la certitude d utiliser cet appareil correctement et en toute s curit veuillez lire attentivement cette notice d instructions avant de mettre l appareil en fonction GEBRUIKSAANWIJZING Voor de klant e Om dit apparaat op de juiste manier en veilig gebruiksaanwijzing aandachtig door te lezen te gebruiken dient u eerst deze MANUAL DE INSTRUCCIONES Para los clientes e Para emplear correctamente este aparato y por razones de seguridad debe leer este manual de instrucciones de manejo antes de su utilizaci n LIBRETTO D ISTRUZIONI Per gli utenti e Per utilizzare correttamente quest unita leggere mente e per intero questo libretto d istruzioni attenta OAHITIEZ AEITONVPIIAZ Ma tov meAaTn e Mid va XPNOLMLOTIOINOETE AUTH TNV UOvO O OWOTA Kal UE AOMAAELA Bebouuafetre OTL EXETE SLABAOEL AUTO TO EYXELPIOLO OONYIW v TIPLV ATO THY xphon INSTRU ES DE OPERA O Para os clientes
17. IR OUTLET AND FAN OF THE INDOOR UNIT BEFORE CONTACTING THE SERVICE REPRESENTATIVE CHECK THE FOLLOWING AGAIN WHEN YOU THINK THAT TROUBLE HAS OCCURRED INSTALLATION RELOCATION AND INSPECTION SPECIFICATIONS W OCONNORWON SAFETY PRECAUTIONS Since rotating parts and parts which could cause an electric shock are used in this product be sure to read these Safety Precautions before use Since the cautionary items shown here are important for safety be sure to observe them Marks and their meanings Z WARNING Incorrect handling could cause a serious hazard such as death serious injury etc with a high probability CAUTION Incorrect handling could cause a serious hazard depending on the conditions Meanings of symbols used in this manual Be sure not to do Be sure to follow the instruction Never insert your finger or stick etc Never step onto the indoor outdoor unit and do not put anything on them Danger of electric shock Be careful Be sure to disconnect the power supply plug from the power outlet Be sure to shut off the power G After reading this manual keep it together with the installation manual in a handy place for easy reference ENCLOSURE Warning positions FRONT PANEL AIR OUTLET ENCLOSURE Aa This air conditioner is NOT intended for use by children or infirm persons without supervisio
18. N switch Each time the EMERGENCY OPERATION switch is pressed the unit will operate in order of EMER GENCY COOL MODE EMERGENCY HEAT MODE and STOP MODE However when the EMERGENCY OPERATION switch is once pressed the unit will operate in test run for 30 minutes and then the operation mode shifts to EMERGENCY MODE Details of EMERGENCY MODE are as shown below However the temperature control does not work for 30 minutes in test run and the unit is set to continuous operation The fan speed is set to High in test run and shifts to Medium after 30 minutes When the remote controller cannot be used emergency operation When the batteries of the remote controller run out or the remote controller malfunctions the emergency operation can be done using the EMERGENCY OPERATION switch A To stop the emergency operation press the EMERGENCY OPERATION switch once in case of EMERGENCY HEAT MODE or twice in case of EMERGENCY COOL MODE Press usinga A the following cases ti i HEAT thin stick When the indoor unit does not respond to the remote Operationimode coo control signal Set temperature 24 C 24 C When the display on the remote controller becomes Fan speed Medium Medium dim Horizontal vane Auto Auto El Press the gt Forward and C4 Backward buttons TIME SET buttons to set the current time MODE FAN_ STOP Ce ECONOCOOL VANE OSTART Cen TIME La RESET CLOCK e
19. O AUTO CHANGEOVER AUTO MODE OPERATION An automatic cooling and heating changeover operation system ensures easy control and year round Description of AUTO RESTART FUNCTION air conditioning Once the desired temperature is set unit operation is switched automatically between cooling These units are equipped with an auto restart function When the main power is turned on the air conditioner will start and heating according to the room temperature In addition fan control of the outdoor unit enables operation automatically in the same mode as the one set with the remote controller before the shutoff of the main cooling operation at outside temperature as low as 10 C Rowen If the unit was set to off with the remote controller before the shutoff of the main power it will remain stopped even after the main power is turned on S If the unit was in the emergency operation before the shutoff of the main power it will start operation when main power Co select the AUTO mode comes on in the same mode as the one set with the remote controller before the emergency operation A MITSUBISHI ELECTRIC H Press the button lf the unit is operated in GY AUTO mode before power failure the operation mode COOL DRY or HEAT is not stored in the memory When the main power is turned on the unit decides the operation mode by the initial room temperature E Select the
20. ausm ll getrennt zu entsorgen sind Bitte entsorgen Sie dieses Ger t bei Ihrer kommunalen Sammelstelle oder im rtlichen Recycling Zentrum In der Europ ischen Union gibt es unterschiedliche Sammelsysteme f r gebrauchte Elektrik und Elektronikgerate Bitte helfen Sie uns die Umwelt zu erhalten in der wir leben Fran ais Votre produit Mitsubishi Electric est con u et fabriqu avec des mat riels et des composants de qualit sup rieure qui peuvent tre recycl s et r utilis s Ce symbole signifie que les quipements lectriques et lectroniques la fin de leur dur e de service doivent tre limin s s par ment des ordures m nag res Nous vous prions donc de confier cet quipement votre centre local de collecte recyclage Dans l Union Europ enne il existe des syst mes s lectifs de collecte pour les produits lectriques et lectroniques usag s Aidez nous conserver l environnement dans lequel nous vivons Les machines ou appareils lectriques et lectroniques contiennent souvent des mati res qui si elles sont trait es ou limin es de mani re inappropri e peuvent s av rer potentiellement dangereuses pour la sant humaine et pour l environnement Cependant ces mati res sont n cessaires au bon fonctionnement de votre appareil ou de votre machine Pour cette raison il vous est demand de ne pas vous d barrasser de votre appareil ou machine usag avec vos ordures m nag res Nederlands
21. ck that the earth is connected correctly CAUTION Earth the unit Do not connect the earth to a gas pipe water pipe light ning rod or the earth of a telephone If the earthing is incorrect it may cause an electric shock Before starting maintenance Turn off the breaker and or disconnect the power supply plug Qa Si A CAUTION When the unit is to be cleaned switch it off and discon nect the power supply plug or turn off the breaker Since the fan rotates at high speed during operation it may cause an injury Cleaning the indoor unit _ Clean the unit using a soft dry cloth If the dirt is noticeable wipe the unit with a cloth soaked in a solution of mild detergent diluted in luke warm water Do not use gasoline benzine thinner polishing powder or insecticide The unit may be damaged The front panel may come off if it is lifted up past its level position If the front panel comes off refer to step E in CLEANING THE FRONT PANEL CLEANING THE FRONT PANEL HEAT EXCHANGER AND FAN ei Remove the air filter before cleaning the heat exchanger Front panel Hold both ends of the front panel and lift the panel up until a click is heard CO Holding the hinges lift the panel up until it is level and pull the hinges forward to remove the front panel d Heat exchanger Z You can sweep the surface of heat exchanger if you instal
22. ded for use in the residential commercial and light industrial environment The product at hand is based on Low Voltage Directive 73 23 EEC the following EU regulations Electromagnetic Compatibility Directive 89 336 EEC d MITSUBISHI ELECTRIC CORPORATION HEAD OFFICE TOKYO BLDG 2 7 3 MARUNOUCHI CHIYODAKU TOKYO 100 8310 JAPAN SG79Y682H01
23. eat depending on model the room consult your dealer since there may be a refrigerant leak Be sure to ask the service representative whether there is refrigerant leakage or not when repairs are carried out The refrigerant charged in the air conditioner is safe Refrigerant normally does not leak however if refrigerant gas leaks indoors and comes into contact with the fire of a fan heater space heater stove etc harmful substances will be generated Electrical work Provide an exclusive circuit for the power supply of the air conditioner Be sure to observe the breaker capacity Z WARNING The customer should not install this unit If installation is done incorrectly it may cause a fire an electric shock or injury from the unit falling water leaking etc Do not use intermediate connection of the power supply cord or the extension cord and do not connect many devices to one AC outlet A fire or an electric shock may result from poor contact poor insulation exceeding the permissible current etc Consult your dealer SPECIFICATIONS A CAUTION Earth the unit Do not connect the earth to a gas pipe water pipe lightning rod or the earth of a telephone If the earthing is incorrect it may cause an electric shock Install an earth leakage breaker depending on the place where the air conditioner is to be installed humid places etc If the earth leakage breaker is not installed it may cause an electric shock
24. he fan rotates at high speed this may cause an injury Young children should be supervised to ensure that they do not play with the air conditioner When an abnormality burning smell etc occurs stop the air conditioner and disconnect the power supply plug and or turn off the breaker If the unit continues to be operated in an abnormal condition it may cause a fire trouble etc In this case consult your dealer A CAUTION When the air filter is to be removed do not touch the metal part of the indoor unit This may cause an injury Do not touch the air inlet or aluminum fin of the outdoor unit This may cause an injury Do not put a vase or glass on the indoor unit Water dropping into the indoor unit may deteriorate the insulation causing electric shock Do not use an insecticide or flammable spray This may cause a fire or deformation of the cabinet Do not put a pet or houseplant where it will be exposed to direct airflow This could injure the pet or plant Do not place other electric appliances or furniture under the indoor outdoor unit Water may drip down from the unit and this may cause damage or malfunction to them Do not leave the unit on an installation stand which is damaged The unit may fall and this may cause an injury Do not step onto an unstable bench when maintaining the unit etc This may cause an injury etc if you fall down Do not pull the power supply cord The core wire
25. he order of timer operations If the current time has not been set the timer operation cannot be used NOTE If the main power is turned off or a power failure occurs while AUTO START STOP timer is active the timer setting is cancelled As these models are equipped with an auto restart function the air conditioner starts operating with timer cancelled at the same time that power is restored WHEN THE AIR CONDITIONER IS NOT GOING TO BE USED FOR A LONG TIME When it is not going to be used for a long time ES Perform the FAN operation for 3 or 4 hours to dry the inside of the air conditioner To perform FAN operation set the remote controller to the highest temperature in the MANUAL COOL mode Refer to page 7 B Turn off the breaker and or disconnect the power supply plug en OY CAUTION Turn off the breaker or disconnect the power supply plug when the air conditioner is not going to be used for a long time Dirt may collect and this may cause a fire a Remove the batteries from the remote con troller Z CAUTION To prevent liquid leakage take out all batteries when the remote controller is not going to be used for a long time MAINTENANCE When the air conditioner is to be used again ER Clean the air filter and install it in the indoor unit Refer to page 10 for cleaning instructions H Check that the air inlet and outlet of the indoor outdoor units are not blocked with any obstacles EJ Che
26. he temperature control temperature setting cannot be done The room temperature is slightly lowered in this operation mode ES The details of the display on the indoor unit are explained on page 6 If the air conditioner doesn t cool or heat effectively If the fan speed is set to Low or AUTO sometimes the air conditioner may not cool or heat the air effectively In this case change the fan speed to Med or upper Change the fan speed Fan speed Low or AUTO Fan speed Med or upper AIR FLOW VELOCITY AND DIRECTION ADJUSTMENT Movement of the horizontal vane To change the horizontal direction of the air flow move the vertical vane manually COOL DRY HEAT At the start Ehl of heating Ell 5 AN Kee E SE When air Horizontal Very small becomes Horizontal position position air flow warm o Position 4 5 si The vane automatically moves to horizontal position Immediately after the air conditioner starts operating Si It will not swing the vane stays at horizontal position Once the air from the indoor unit becomes sufficiently warm the NOTE 8 vane moves to position 4 Adjust the vane before operation starts i Air blows out upper than position 1 _ Once the air conditioner starts operating the fan Since the horizontal vane moves automatically your fingers may be caught To con
27. hough the set temperature is automatically set 2 C higher it is possible to perform cooling operation with keeping comfort As a result energy can be saved TIMER OPERATION ON OFF TIMER It is convenient to set the timer when you go to bed when you get home when you get up etc How to set the ON timer How to set the OFF timer Press the 2 button during operation ER Press the o button during operation 0 O 1 Each time the button is pressed the ON timer mode Each time the button is pressed the OFF timer mode alternates between ON and OFF alternates between ON and OFF E Set the time of the timer using the TIME but E Set the time of the timer using the TIME but tons gt J Forward and lt Backward tons gt Forward and C lt Backward Each time the C button is pressed the set time Each time the L button is pressed the set time increases by 10 minutes each time the C lt button is increases by 10 minutes each time the a button is pressed the set time decreases by 10 minutes pressed the set time decreases by 10 minutes to release the OFF timer ES Press the ca button To release the ON timer ES Press the SCH button SAM Programming timer operation The ON timer and the OFF timer can be used in combination The timer of the set time that is reached first will operate first t mark indicates t
28. ing pressure Noise level LP ps HP ps Indoor Super High High Med Low 48 44 38 32 48 42 36 30 Outdoor 52 55 NOTE 1 Rating condition Cooling Indoor 27 C DB 19 C WB Outdoor 35 C DB Heating Indoor 20 C DB Outdoor 7 C DB 6 C WB 2 Guaranteed operating range Outdoor 43 C DB 10 C DB 24 C DB 18 C WB 10 C DB 11 C WB Upper limit Lower limit Upper limit Lower limit WEEE Note This symbol mark is for EU countries only This symbol mark is according to the directive 2002 96 EC Article 10 Information for users and Annex IV English Your MITSUBISHI ELECTRIC product is designed and manufactured with high quality materials and components which can be recycled and reused This symbol means that electrical and electronic equipment at their end of life should be disposed of separately from your household waste Please dispose of this equipment at your local community waste collection recycling centre In the European Union there are separate collection systems for used electrical and electronic product Please help us to conserve the environment we live in Deutsch Ihr MITSUBISHI ELECTRIC Produkt wurde unter Einsatz von qualitativ hochwertigen Materialien und Komponenten konstruiert und gefertigt die fur Recycling geeignet sind Dieses Symbol bedeutet dass elektrische und elektronische Ger te am Ende ihrer Nutzungsdauer von H
29. l the brush of QUICK CLEAN KIT to your vacuum cleaner Please refer to the instructions described in QUICK CLEAN KIT for details A CAUTION Z WARNING Do not touch the heat exchanger directly with your hands Otherwise you may get injured It s recom mended to protect your hands with a pair of gloves A CAUTION Do not step onto an unstable bench when cleaning Otherwise you may fall down and get injured Use only the brush of QUICK CLEAN KIT Do not use other stuffs Otherwise the heat exchanger of the indoor unit may get damaged Do not drop the front panel or pull it out forcibly The panel may be damaged Do not step onto an unstable bench when removing or installing the front panel This may cause an injury etc if you fall down H Wipe the front panel with a soft dry cloth or wash it with water After washing the panel wipe up the remain ing water with a soft dry cloth and let it dry out of direct sunlight If the dirt is noticeable wipe the front panel with a cloth soaked in a solution of mild detergent diluted in lukewarm water Optional product Name of parts Quick Clean Kit MAC 093SS E Do not use gasoline benzine thinner polishing Parts number powder or insecticide and do not wash the front CLEANING THE AIR FILTER CATECHIN Cleaning the air filter about once every 2 weeks ES Remove the air filter Open the front panel then remove replace the filter
30. maged Do not use excessive force to the fan guard during this procedure The fan guard may be deformed and the vanes may not work properly Put the vertical vanes back correctly to their original positions Otherwise condensed water may drip down from the indoor unit or the horizontal vane could malfunction H install the horizontal vanes Reverse the removal procedures H Swing the vertical vanes out one by one Holding the unit lightly with one hand grab the tab 27 Hold the tab of each vertical vane and move the of each vertical vane with the other hand and pull it vertical vanes in the directions of the arrows downward to swing out each vertical vane The vanes cannot be removed Insert this end first Pull towards you In procedure lock the stoppers until they click into place After Cleaning Insert the power supply plug into the power outlet and or turn on the breaker Check that all LED lamps are not blinking If they are blinking the horizontal vane is not installed correctly In this case disconnect the power supply plug and or turn off the breaker and then reinstall the horizontal vane by following the procedures in step I If you operate the air conditioner after cleaning the air outlet and fan do not get close to the air outlet as any remaining dirt may be discharged Be sure to hold the tab to swing out
31. matically moves the vane to position 1 the vane stays at horizontal position Once the air 3 ii SH d d blowi iti Wu e Se GE e F F Ge previously set position ditioner starts the cooling or ward blowing position To change the air flow direction to the original setting from the indoor unit becomes sufficiently warm the A Gees VANE A i Horizontal drying operation in approx When the CC button is operate the VANE button on the remote controller vane moves to the position corresponding to the set zu gt d ani position 3 minutes pressed again the vane again e Gs direction or alr low i e returns to the previously set The vane does not move to the straight down position Once the air conditioner starts operating the fan osition and the air condi in the COOL and DRY mode speed increases gradually as the air from the indoor Ve starts heating opera unit gets warmer and continues until the set speed is tion inapprox 3 ee finally reached GE The vane moves intermittently between positions 1 The vane moves intermittently between positions 2 NOTE M P VANE and 4 The vane stops for a brief period at positions and 4 The vane stops for a brief period at positions e you frais thie ar How not to Blow directly onto yout body by pressing gt button the compresser stops for 3 1 and 4 2 and 4 minutes even during the operation of the air conditioner i The air conditioner operates with decreased air flow until the compre
32. n drying it REPLACEMENT OF THE AIR CLEANING FILTER OPTION When the capacity is lowered because of dirt etc it is necessary to replace the air cleaning filter Air cleaning filter replacement about once every year 1 Remove the air filter left one The air cleaning filter is not attached to the right side air filter EE Ch Air filter A E Pull up the tabs on both sides of the air clean ing filter with your finger and remove the air cleaning filter blue bellows type from the air filter Air filter Back side H Attach a new air cleaning filter to the air filter so that all 8 tabs on the air filter are securely installed ER Install the air filter Securely install its tabs EE 7 N H Securely close the front panel See eeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeee Air cleaning filter If the air cleaning filter is clogged it may lower the unit s capacity or cause condensation at the air outlet The air cleaning filter is disposable The standard usable term is about 1 year Optional parts Optional parts are available from your local dealer Name of parts Parts number AIR CLEANING FILTER Anti Allergy Enzyme Filter MAC 415FT E This optional part is for the replacement of the left side filter only No optional part is available for the right side filter CLEANING THE AIR OUTLET AND FAN OF THE INDOOR UNIT Before
33. n electric shock PREPARATION BEFORE OPERATION Remote controller How to set the batteries and the current time Remove the front lid and insert batteries Then reattach the front lid Insert the minus pole of the batteries first Check if the polarity of the batteries is correct Insert the minus pole of the batteries first Press using a thin stick If the RESET button is not pressed the remote controller may not operate correctly Be sure to press the RESET button not too strongly E Press the CLOCK set button Handling of the remote controller The range that the signal can reach is about 6 m when the remote controller is pointed at the front of the indoor unit When a button is pressed one or two beeps will be heard from the indoor unit If no sound is heard operate again Use the remote controller carefully If it is dropped thrown or it gets wet the remote con troller may not operate When installing on a wall etc Install the remote controller holder in a position where the signal reception sound beep can be heard from ONOFF the indoor unit when the button is pressed How to install remove the remote controller Installing Insert the remote controller downward Removing Pull it up Remote controller holder Dry cell batteries m Reference for replacing batteries Replace the batteries with new AAA alkaline batteries in ES Press the EMERGENCY OPERATIO
34. ng may be Lal heard This is not a malfunction since the refrigerant continuously flows into the indoor unit that does not operate acd SE EI Details of display on the indoor unit E When the set temperature is to be changed d The operation indicator at the right side of the indoor unit indicates the operation state Press the Di button to lower the temperature One press lowers the temperature by about 1 C 7 peza Press the 6 button to raise the temperature One press raises the temperature by about 1 C Operation Indicator RK oO sey GE Not lighted Description of AUTO CHANGEOVER 1 Initial mode Operation indicator lamp gt When unit starts the operation with AUTO operation from off If the room temperature is higher than the set temperature operation starts in COOL mode Difference between target If the room temperature is equal to or lower than the set temperature operation starts in HEAT mode Indication Operation state temperature and room temperature 2 Mode change e z a z COOL mode changes to HEAT mode when about 15 minutes have passed with the room temperature 2 degrees ei a GER EE ne e About 2 C or more below the set temperature obtained 2 HEAT mode changes to COOL mode when about 15 minutes have passed with the room temperature 2 degrees above the set temperature ee This shows that the room temperature is approaching the target About 2
35. ns A WARNING Do not use intermediate connection of the power supply cord or the extension cord and do not connect many devices to one AC outlet A fire or an electric shock may result from poor contact poor insulation exceeding the permissible current etc Remove dirt from the power supply plug and securely insert the plug into the outlet If dirt adheres to the plug or insertion is incomplete it may cause a fire or an electric shock Do not scratch or process the power supply cord etc Do not put heavy object on the power supply cord and do not scratch or process the cord The cord may be damaged and this may cause a fire or an electric shock Do not turn the breaker off on and or disconnect connect the power supply plug during operation This may cause a fire due to spark etc Be sure to turn off the breaker and or disconnect the power supply plug absolutely after switching the indoor unit off with the remote controller Do not expose your skin directly to cool air for a long time This could damage your health Installation repairs or relocation should not be done by the customer If this is done incorrectly it may cause a fire an electric shock or injury from the unit falling water leaking etc Consult your dealer If the power supply cord is damaged it must be replaced by the manufacturer or its service agent in order to avoid a hazard Do not insert your finger or a stick etc into the air inlet outlet Since t
36. of the power supply cord may be disconnected and this may cause a fire Do not charge or disassemble the batteries and do not throw them into a fire This may result in leakage fire or an explosion Do not operate the unit for a long time in high humidity e g leaving a door or window open In the cooling mode if the unit is operated in a room with high humidity 80 RH or more for a long time water condensed in the air conditioner may drop and wet or damage furniture etc SAFETY PRECAUTIONS NAME OF EACH PART A CAUTION Do not use the unit for special purposes Do not use this air conditioner to preserve precision devices food animals plants and art objects This may cause deterioration of quality etc Heat exchanger Do not put a stove etc where they are exposed to direct airflow This may cause imperfect combustion Do not operate the unit at low outside temperature less than 10 C in the cooling mode Inthe cooling mode if the unit is operated at low outside temperature less than 10 C water condensed in the air conditioner may drop and wet or damage furniture etc When the unit is to be cleaned switch it off and disconnect the power supply plug and or turn off the breaker Since the fan rotates at high speed during operation this may cause an injury When the unit is not going to be used for a long time disconnect the power supply plug and or
37. or water leaking air inlet back and side Do not install the unit where flammable gas could leak If gas leaks and collects around the unit it may cause an explosion A CAUTION Earth the unit Do not connect the earth to a gas pipe water pipe lighthing rod or the earth of a telephone If the earthing is incorrect it may cause an electric shock Install an earth leakage breaker depending on the place where the air conditioner is to be installed humid places etc If the earth leakage breaker is not installed it may cause an electric shock Front panel Air cleaning filter Optional parts Anti K Ak a Allergy Enzyme Filter Blue bellows type Air filter Catechin Air outlet Remote controller iS trrfrtertrrertert i i ct qaaqaaaae Air outlet Drain should be fully drained Ifthe drainage route is incomplete water may drop from the unit This may wet and damage the furniture iii inn UN Drain outlet NAME OF EACH PART Remote controller C Signal transmitting section D Operation display section ON OFF operate stop button ONOFF JEROdER Temperature buttons Open the front lid NOTE Use the remote controller provided with
38. ppliances being pressed When a power failure occurs Does the air conditioner start operating again If the air conditioner had operated before the power failure as these models are equipped with an auto restart function the air conditioner should start operating again Refer to Descrip tion of AUTO RESTART FUNCTION on page 6 Even if the above items are checked when the air conditioner does not recover from the trouble stop using the air conditioner and consult your dealer In me following cases stop using the air conditioner and consult your dealer When water leaks or drops from the indoor unit When the left operation indicator lamp blinks When the breaker trips frequently The remote control signal may not be received in a room where an electronic ON OFF type fluorescent lamp inverter type fluorescent lamp etc is used Operation of the air conditioner may interfere with radio or TV reception in areas where the reception is weak An amplifier may be required for the affected device When thunder is heard stop operation and disconnect the power supply plug or turn off the breaker Otherwise the electrical parts may be damaged WHEN YOU THINK THAT TROUBLE HAS OCCURED Question Answer not a malfunction The air conditioner cannot be operated for about 3 minutes when restarted This protects the air conditioner according to in structions from the microprocessor Please
39. ssor turns on again gl g m Cl Re D NOTE Adjust the vertical AIR FLOW direction using the remote controller Moving the horizontal vane manually can cause trouble When the operation mode changes in OC AUTO mode the horizontal vane is automatically changed to the position in each mode ECONO COOL OPERATION Use this operation when you want to be comfortable in COOL mode even with energy saved Perform the following operations while the unit is operat ing in the MANUAL COOL mode ER Press the button When the ECONO COOL operation is selected in COOL mode the air conditioner performs swing operation vertically in various cycle according to the temperature of air conditioner Also SET TEMPERATURE is automatically set 2 C higher than in COOL mode To release the ECONO COOL operation ae MITSUBISHI ELECTRIC OFF WES DESS ECONO COOL MODE FAN STOP ES Press the Ce button again KE See eeeeeeeeeeeeeeeeeeeeeeeeeeeeeee ECONO COOL VANE f START E When the SST button is pressed or the operation mode is changed during the ECONO COOL operation ECONO COOL operation is released FAN d d TIME The button the Di or A button and ON OFF timer explained below Lal are available RESET CLOCK 14 ER What is ECONO COOL Swing air flow change of air flow makes you feel cooler than constant air flow So even t
40. stantly change the air flow direction select speed increases gradually as the air from the indoor f a x SWING with the It button unit gets warmer and continues until the set speed is To change the air flow direction not to blow directly onto your body finally reached To change the air A 3 Stee flow direction When to use this function COOL DRY HEAT gt of heatin set Sal gt Pressing and holding Use this function if you don t The air conditioner starts the The air conditioner starts heat en When air the button for want the air from the indoor cooling or drying operation ing operation approx 3 min ou Position 1 Horizontal Very small becomes 2 seconds or more unit to blow directly onto your approx 3 minutes after the utes after the vane has moved Position air flow warm Set Position causes the horizontal body vane has moved to the hori to the horizontal position vane to reverse and Depending on the shape of zontal position Sometimes the area around When the air flow direction is move to horizontal the room the air may blow When the button is your feet may not warm To 2 set to position 2 3 or 4 position directly onto your body pressed again the vane warn the area around the i i s feet set the horizontal vane ES After around one hour of operation the air conditioner Immediately after the air conditioner starts operating d e za peace ee ee abcess to AUTO or the down auto
41. sto prodotto portarlo al centro di raccolta riciclaggio dei rifiuti solidi urbani locale Nell Unione Europea ci sono sistemi di raccolta differenziata per i prodotti elettrici ed elettronici usati Aiutateci a conservare l ambiente in cui viviamo EAAnvika To mpoidv MITSUBISHI ELECTRIC mou d1a8 tete eivat oxedtaoUEVO KAL KATAOKEUAGHEVO AT UAIKG Kal e apTHYaTa UWNArs MoLoTNTac Ta omoia unopo v va avakuUKAWB8oUv Kal va xprnolwortomPouv Eava To GULBOAO aut onpaivet OTL O NAEKTPOAOYIKOS Kal NAEKTPIKOG EEOTIALOOG OTO TEAOG TNG StapKELac W G TOU Ba TIPETtEL Va arloppipTei EEXWPIOT ano Ta uTIOAOIMG OIKIAK aMoppippaTa oac Napakadovue StaG ote eEaAeipte Tov EEFOMALOUO AUTO OTOV TOTILKO GAC KOLVOTIKO KEVTPO GUAAOYI C aVaKUKAWONS ATLOPPIULATOWV Zmv Evpwnaiky Evwon umdapxouv Eexwplota ouotT uaTa ouAAoyr yia Ta XPNOIWoTIOINHEVA NAEKTPOAOYIKG KOL nNAeKkTptKa mpo vTta Bonfnore pa va MpootaTevGOULE To MEpIBGAAOV oTo onoio Gouugl Portugu s O seu produto MITSUBISHI ELECTRIC foi concebido e produzido com materiais e componentes de alta qualidade que podem ser reciclados e reutilizados Este s mbolo significa que o equipamento el ctrico e electr nico no final da sua vida til deve ser deitado fora separadamente do lixo dom stico Por favor entregue este equipamento no seu ponto local de recolha reciclagem Na Uni o Europeia existem sistemas de recolha separados para produtos el ctricos e electr nicos usados Por
42. t provide drainage work in such climate that the outdoor unit may get frosted White smoke is discharged from the outdoor unit Inthe heating operation vapor generated by the defrosting operation looks like white smoke Air does not blow out soon in the heating operation Please wait as the air conditioner is preparing to blow out warm air The operation is stopped for about 10 minutes in the heating operation Defrosting of the outdoor unit is being done Defrosting operation Since this is completed in 10 minutes please wait When the external temperature is too low and humidity is too high frost is formed Hissing sound is sometimes heard This is the sound when the flow of refrigerant inside the air conditioner is switched The room cannot be heated sufficiently In a multi unit system the indoor unit which is not operating becomes warm and a sound similar to water flowing is heard from the unit When the outside air temperature is low the heating effect may not be sufficient A small amount of refrigerant continues to flow into the indoor unit even though it is not operat ing The air conditioner starts the operation only with the main power turned on though you do not operate the unit with the remote controller These models are equipped with an auto restart function When the main power is turned off without stopping the air conditioner with the remote
43. ted to a vacuum cleaner with a hose tube diameter inside diameter of 32 to 39 mm Refer to the instructions of the QUICK CLEAN KIT Refer to page 12 for cleaning the fan What is Catechin air filter The air filter is dyed with a natural material catechin that is contained in tea The catechin air filter deodorizes odor and noxious gases such as formaldehyde ammonia and acetaldehyde Moreover it restrains the activity of the viruses adhering to the filter CLEANING THE AIR CLEANING FILTER OPTION Cleaning the air cleaning filter about once every 3 months Remove the air filter left one The air cleaning filter is not attached to the right side air filter O Air filter N H Pull up the tabs on both sides of the air clean ing filter with your finger and remove the air cleaning filter blue bellows type from the air filter Air filter Back side EJ Soak the filter together with its frame in luke warm water and wash it WI the dirt is noticeable use a solution of mild deter gent diluted in lukewarm water E if hot water 50 C or more is used the filter may be deformed E Do not use a scrubbing brush or sponge This may damage the surface of the filter E Do not use a chlorine detergent D After rinsing with water lukewarm water shake off the excess water and dry the filter well in the shade E Do not expose the filter to direct sunlight or heat from a fire whe
44. turn off the breaker Otherwise dirt may collect and this may cause a fire i i Replace the 2 batteries of the remote controller with new ones of same type Using an old battery together with a new one may result in heat generation leakage or an explosion Fan If liquid from the batteries gets onto your skin or clothes wash it well with clean water If liquid from the batteries gets into your eyes wash them well with clean water and consult a doctor at once Ventilate well in using the unit with a stove etc An oxygen shortage may occur Do not operate switches with wet hands This may cause an electric shock Operation section Display section Do not clean the air conditioner with water or put a vase or glass on it When the front panel is opened Wat ter the unit and degrade the insulation Thi lectric shock OPERATION INDICATOR ater may enter the unit and degrade the insulation This may cause an electric shock Operation Indicator Do not step or put anything on the indoor outdoor unit lamp This may cause an injury etc if you or something falls down G INVERTER a For installation SC Emergency operation switch Remote control a receiving section wanne Consult your dealer for installation of the air conditioner Since special techniques and work are required utdoor unit installation should not be done by the customer If this is done incorrecty it may cause a fire an electric shock injury
Download Pdf Manuals
Related Search