Skywalker X-8 Installation Manual
Contents
1. Skywalker X 8 Installation Manual Thank you for Purchasing the Sky walker X 8 Plane The skywalker X 8 is designed for First Person Vision FPV application specifically Technical parameters Wingspan 2120mm weight 880G motor 2820 KV730 ESC 70A Battery pack 458000 10000MAH propeller 12X6 13X8 Take off weight 3200G KIT version includes Fuselage wing winglet tubes accessories bag sticker Glue the winglet layers spread the glue evenly over the wing and both sides of the layers the layer marked with T board belongs to parts of the main wing Wait for 5 minutes to allow glue to dry until it is non sticky then they can be glued in alignment Glue the hatch magnets after compressing the magnet tightly fix them with CA glue After gluing put it together and inspect the mounting spacing Glue the servos please choose the standard servos provided by skywalker or servos with moment more than 2 5 KG Glue the rudder horn spread the glue evenly and wait for its dryness then Glue the rudder horn Power on the servo and place it in the mid position then lock the regulator screw tighten the steel wire And shorten the extra length of the wire Glue the fixed layer of the winglets please be sure to spread the glue evenly and wait until it is completely dry afterwards you can glue the layer 1 0 Cut out the pre reserved slot on the aileron onl2. ust this construction you can also use a nut to butt Fix the winglets with two 3 x8 screws with the purpose of a long term usage of the layer plate it is suggested that consolidating the screw hole with CA glue before twist the screw 29 2 6 If you glue the motor frame previously you can fix the motor now nn We suggest you use brand quality propeller of CAM or APC or offered and tested by us 2 We reserved the mounting positions of CCD holder and GOPRO 28 You need to open a round hole in the corresponding position of the GOPRO s lens And cut out a bevel to ensure not to obscure the vision of the wide angle lens The position of the center of gravity of X 8 is 440 mm away from the nose 5 mm correction interval in front and at the back of it 2 9 The installed machine can be decomposed into small parts which is easy to carry 3 0 Done Finally Please note that control X 8 s flight speed within 85 km H If you need a high speed flight please strengthen wings please control the machine load within 3200 g if exceed the limit please strengthen wings Thank you again for choosing skywalker series products If there are technical problems or suggestions please email us for consultation Or consult your local dealers
3. y about 1 5 mm wide by a new blade Wing plate bonding please to smear evenly on all surfaces please not to spread the glue over the tube slot 11 Settle the extending line in the line slot previously and spread the glue evenly over the plate Wait for the two planes dryness later spread some glue over the vertical planes and then fix and flatten them LZ The side plate bonding spread the glue on both sides of the plate 13 It is recommended to insert the tube into the wing to guide the butt plate which is more accurate 14 15 The line slot of early product also need to be widened to let the the extending line with plug directly into the fuselage 1 6 Fix the motor and cement it to the fuselage in advance you can also first fix the layer board base and afterwards install the motor 17 1 8 19 2 0 After the two sides is dry align and glue them And then glue the butt plate of the fuselage 21 Still use the tube as a guide align and glue it 2 2 After gluing you can butt the wing to make a trial of the accuracy insert the extending into the fuselage through the line slot 2a We can see the butt is perfect As the airframe is designed to be very wide you can easily put your FPV equipment down and separate the transmitter and receiver 24 Fixing the wing is also very simple just a screw of course if you don t tr
Download Pdf Manuals
Related Search