LED BEAM MOVING HEAD FL
Contents
1. 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal Pin 4 Pin 5 not used 11 Troubleshooting Following are a few common problems that may occur during operation Hear are some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work e Check the connection of power and main fuse e Measure the mains voltage on the main connector e Check the power on LED B Not responding to DMX controller e DMX LED should be on If not check DMX connectors cables to see if link properly e If the DMX LED is on and no response to the channel check the address setting and DMX polarity e If you have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one e Tryt to us another DMX controller e Check if the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C Some units don t s respond to the easy controller www flash butrym pl Page 12 e You may have a break in the DMX cabling Check the LED for the response of the Master Slave mode signal e Wrong DMX address in the unit Set the proper address D No response to the sound e Make sur the unit dose not receive DMX Signal e Check microphone to see if it is good by tapping the microphone E One of the channels is not working well e The stepper motor might be2. mode has been selected press the ENTER buton to setup to go back to the functions whitout any 9 change press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode www flash butrym pl Page 7 White Balance Select White Balance press the ENTER buton to confirm present mode will blink on the display Use DOWN and UP buton to select the Red or Green or Blue Once the mode has been selected press the ENTER buton to setup use the DOWN and UP buton to change the value 125 255 Once the mode has been selected press the ENTER buton to setup go back to the functions whitout any change press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Manu Test Select Manu Test press the ENTER buton to confirm present mode will blink on the display Use DOWN and UP buton to select the Pan Tilt Red Green Blue White Dimmer or Strobe Once the mode has been selected press the ENTER buton to setup use the DOWN and UP buton to change the value 0 255 Once the mode has been selected press the ENTER buton to setup go back to the functions whitout any change press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Auto Test Press the MENU buton up to when the Auto Test is blinking on the display Pressing ENTER buton and the unit will run self test by built in p
3. LED BEAM MOVING HEAD FL 101 36x3W User Manual www flash butrym pl Page 1 1 Preface 1 1 Packing list Product name quantity moving head light 1 pcs Power line 1 base User manual 1 pcs 1 2 Unpacking instructions On receiving a fixture carefully unpack the carton check the contents to ensure that all parts are presented and have been received in a good condition Notify the shipper immediately and retain packing material for inspection if any parts appear damaged from shipping or the carton itself shows sign of mishandling Save the carton and all packing materials In the event that a fixture must be returned to the factory it is important that the fixture should be returned in original factory box and packing 1 3 AC Power To determine the power requirements for a particular fixture see the label affixed to the back plate of the fixture or referred to the fixtures specification chart A fixture listed current rating is its average current draw under normal conditions All fixtures must be directly powered off a switched circuit and cannot be run off a rheostat variable resist or dimmer circuit even if the rheostat or dimmer source voltage matches the fixtures requirement Check the fixture or device carefully to make sure that if a voltage selection switch exits that it is set to the correct line voltage you will use Warning Verify that the voltage select switch on your unit matches the line v
4. Tilt Auto Run CH7 000 255 Auto Run Speed CH8 000 255 Auto Run Color Open CH9 000 255 Dimmer 0 100 CH10 000 255 Strobe CH11 000 255 Red 0 100 CH12 000 255 Green 0 100 CH13 000 255 Blue 0 100 CH14 000 255 White 0 100 CH15 000 255 Color Auto Run CH16 000 255 Color Auto Run Speed www flash butrym pl Page 11 10 DMX512 Connection 1 If you usign a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 2 At last unit the DMX cable has be terminated with a terminator Solder a 120ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable can not branched or split to a Y cable DMX512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded conectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circuit when one of the units power is disconnected 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address numer is between 0 511 usualy 0 amp 1 are equal to 1 6 The end of the DMX512 system should be terminated to reduce signal errors 7 3 pin XLR connector are more popular than 5 pin XLR 3 pin XLR Pin 1 GND Pin
5. ctions without any change press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Reset Press the MENU buton up to when the Rest is blinking on the display Pressing ENTER buton and all channels of the unit will return to their standard position 5 Home Position Adjust Pan Offset 127 Offset Tilt Offset 127 In the main functions hold ENTER buton for at least 3 seconds into offset mode use DOWN and UP buton up to chose Pan Offset or Tilt Offset Pressing ENTER buton and the display will blink Use Down and UP buton to adjust the home position of the Pan Tilt Once the opposition has been selected press the ENTER buton to setup to go back to the functions without any change press the MENU buton again Hold and press the MENU buton about one secondo r wait for one minute to exit the menu mode 6 How to Control The Unit You can operate the unit in two ways 1 Master Slave built in preprogram function 2 Universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effect a tonce Every time you turn the unit on it will show www flash butrym pl Page 9 M108RGBW on the display and move all the motors to their HOME position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 7 Master Sla
6. damaged or cable connected to PCB is broken e The motor s drive IC on the PCB might be out of conditio 12 Fixture Cleaning The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s opyics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days www flash butrym pl Page 13
7. his In the event of a serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to a dimmer device Make sure the power cord never crimped or damaged Never disconnect the power cord by pulling or gagging on the cord Avoid direct eye exposure to the light source while it is on www flash butrym pl Page 3 2 Technical Specification e Extremely small fast and powerful LED Moving Beam e DMX Channels 9 12 16CH e Pan Tilt 650 240 speed adjustable e Smooth electronic dimming 0 100 e Electronic strobe with pulse and random effects e High efficiency low power consumption e Super compact low weight Weight 5 7kg Voltage 100V 240V 50 60Hz Fuse T6 3A Power Consumption 150W Light source 3W LED x36 R8 G10 B10 W8 Dimension 375x322x445mm 3 Display To show the various menus and the selected functions LED DMX ON DMX Input Present MASTER ON Master Mode SLAVE ON Slave Mode SOUND Flashing Sound Activation Button MENU To select the programming functions DOWN To go backwardin the selected functions UP To go forward in the selected functions ENTER To confirm the selected functions Mains Input Connect to su
8. hout any change press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Black Out Select Slave Mode Press the ENTER buton to confirm present mode will blink on the display Use the DOWN and UP buton to select the Yes yes blackout or No no blackout mode Once the mode has been selected press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Sound State Select Sound State Press the ENTER buton to confirm present mode will blink on the display Use the DOWN and UP buton to select the ON sound on or Off sound off mode Once the mode has been selected press the ENTER buton to setup to go back to the functions without any change press the MENU buton again Hold and www flash butrym pl Page 6 press the MENU buton about one secondo or wait for one minute to exit the menu mode Sound Sense Select Sound Sense Press the ENTER buton to confirm present mode will blink on the display Use the DOWN and UP buton to select the 0 1000 mode Once the mode has been selected press the ENTER buton to setup to go back to the functions without any change press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Pan Inverse Select Pan Inverse Press the ENTER button to confirm present mode will blink on the display Use the DOWN and UP buton t
9. o select the Yes Pan Inversion or No Normal mode Once the mode has been selected press the ENTER buton to setup to go back to the functions whitout any change press MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Tilt Inverse Select Tilt Inverse Press the ENTER buton to confirm present mode will blink on the display Use the DOWN and UP buton to select the Yes Tilt Inversion or No Normal mode Once the mode has been selected press the ENTER buton to setup to go back to the functions without any change press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Back Light Select Back Light Press the ENTER buton to confirm present mode will blink on the display Use the DOWN and UP buton to select the On LED On or Off LED Off mode Once the mode has been selected press the ENTER bbutonto setup to go back to the functions without any change press the MENU buton again Hold and press the MENU buton about one secondo or wait the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Function Delay Select Function Delay press ENTER buton to confirm present mode will blink on the display Use DOWN and UP buton to select the No Delay or 1S 2S 3S Delay Wait for 1 2 3 seconds before these Functions of 12CH are activated deactivated mode Once the
10. oltage applied Damage to your fixture may result if the line voltage applied does not match the voltage indicated on the voltage selector switch All fixtures must be connected to circuits with a suitable Earth ground www flash butrym pl Page 2 1 4 Safety instructions Please read these instructions CV it includes important information about the installation usage and maintenance of this product Please keep this user guide for future consultation If you sell the unit to another user be sure that they also receive this instruction booklet Always make sure that you are connecting to the proper voltage and that the line voltage you are connecting to is not higher than that stated on the decal or rear panel of the fixture This product is intended for indoor use only To prevent risk of fire or shock do not expose fixture to rain or moisture Make sure that there are no flammable materials close to the unit while operating The unit must be installed in a location with adequate ventilation at least 20in 50cm from adjacent surfaces Be sure that no ventilation slots are blocked Always disconnect from power source before servicing or replacing fuse and be sure to replace with same fuse size and type Secure fixture to fastening device using a safety chain Never carry the fixture solely by its head Use its carrying handles Maximum ambient temperature Ta is 104 F 40 C Do not operate fixture at temperatures higher than t
11. pply power Mains Output Connect to supply power to the next unit DMX Input Output For DMX512 link use 3 5 pin XLR cable to link the unit together 4 Main Function To select any of the given functions Press the MENU buton up to when the required one is showing on the display Select the function by ENTER buton and the display www flash butrym pl Page 4 will blink Use DOWN and UP buton to change the mode Once the required mode has been selected press the ENTER buton to setup to go back to the functions whitout any change press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode The main functions are showing below MENU DMX Address 001 512 Channel Set 9ch 12ch 16ch Show Mode Show 1 Show 2 Show 3 Show 4 Slave Mode Slave 1 Slave 2 Black Out Yes No Sound State On Off Sound Sense 0 100 PAN Inverse Yes No Tilt Inverse Yes No Back Light On Off White Balance Red 125 Green Blue 255 Menu Test PAN Tilt Red Green Blue White Dimmer Strobe Auto Test Temp 31 C Defaults No Pro Defaults Yes Auto Defaults www flash butrym pl Page 5 DMX Address Select DMX Address press the ENTER b
12. rogram To go back to the functions press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Temperature Press the MENU buton up to when the Temperature Test is blinking on the display Pressing ENTER buton and the unit will run self test by built in program To go back to the functions press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Defaults Setting Press the MENU buton to show Defaults on the display Press the ENTER buton and the display will blink Use the DOWN and UP buton to select the YES or No Once the Yes has been selected press the ENTER buton and use the UP and Down buton to select the PRO Defaults or AUTO Defaults PRO Defaults For professional users detailed explanation as followings e Slave Mode Slave 1 e Black Out Yes e Sound State Off e Pan Inverse No e Tilt Inverse No www flash butrym pl Page 8 e Back Light Off e Function Delay 3s Delay Auto Defaults Mostly automatic mode for non professional users detailed explanation as followings e Slave Mode Slave 1 e Black Out No e Sound State On e Pan Inverse No e Tilt Inverse No e Back Light On Notice Other settings are NOT changed while choosing Defaults Setting Press the ENTER and the corresponding functions will set to defaults setting to go back to the fun
13. ut one secondo r wait for one minute to exit the menu mode Please refer to the following diagram to address your DMX512 channel for the first 4 units Channel Mode Unit 1 Address Unit 2 Address Unit 3 Address Unit 4 Address 9 channels 1 10 19 28 12 channels 1 13 25 37 16 channels 1 17 33 49 9 DMX512 Configuration 9 Channel Mode Channel List Value Function CH1 000 255 Pan 0 630 CH2 000 255 Tilt 0 240 www flash butrym pl Page 10 CH3 000 255 Strobe CH4 000 255 RED 0 100 CH5 000 255 GREEN 0 100 CH6 000 255 BLUE 0 1000 CH7 000 255 WHITE 0 100 CH8 000 255 Dimmer 0 100 CH9 000 255 Sound Active 12 Channel Mode Channel List Value Function CH1 000 255 Strobe Effect CH2 000 255 Dimmer 0 100 CH3 000 255 Pan 0 630 CH4 000 255 E Fine Least significant CH5 000 255 Tilt 0 240 CH6 000 255 a Fine Least significant CH7 000 255 Sound Activation CH8 000 255 Color Effect CH9 000 255 RED 0 100 CH10 000 255 GREEN 0 100 CH11 000 255 BLUE 0 1000 CH12 000 255 WHITE 0 100 16 Channel Mode Channel List Value Function CH1 000 255 Pan 0 630 CH2 000 255 Fine Least significant CH3 000 255 Tilt 0 240 CH4 000 255 H Fine Least significant CH5 000 255 Pan amp Tilt Speed CH6 000 255 Pan amp
14. uton to confirm the present address will blink on the display Use the UP and DOWN buton to adjust the address from 1 to 512 Once the address has been selected press the ENTER buton to setup to go back to the functions without any change press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Channel Set Select Channel Set press the ENTER buton to confirm the present set will blink on the display Use the UP and DOWN buton to select channel 9 12 16 Once the set has been selected press the ENTER buton to setup to go back to the functions without any change press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Show Mode Select Show Mode Press the ENTER buton to confirm present mode will blink on the display Use the DOWN and UP buton to select the Show 1 or Show 2 or Show 3 or Show 4 mode Once the mode has been selected press the ENTER bitton to setup to go back to the functions without any change press the MENU buton again Hold and press the MENU buton about one secondo or wait for one minute to exit the menu mode Slave Mode Select Slave Mode Press the Enter buton to confirm present mode will blink on the display Use the DOWN and UP buton to select the Slave 1 normal or Slave 2 2 light show mode Once the mode has been selected press the ENTER buton to setup to go back to the functions wit
15. ve Built In preprogrammed Function By lining the units in master slave connection the first unit will controll the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show You have to set the first unit in master mode Show Mode and select Show 1 or Show 2 or Show 3 ors Show 4 mode Its DMX input jack will have nothing plugged into it and its master LED will be constantly on and sound LED will flash to the music The other units will have to set in Slave mode and select Slave 1 normal or Slave 2 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave led lights will constantly on 2 light show In Slave mode Slave 1 means the unit works normally and Slave 2 means 2 light show In order to create a great light show you can set Slave 2 on the second unit to get contrast movement to each other even if you have two units only 8 DMX Controller By using a universal DMX Controller to control the units you will need to set DMX address from 1 to 512 so that the units can recive DMX signal Press the MENU buton up to when the DMX Adress is showing on the display Pressing ENTER buton and the display will blink Use DOWN and UP buton to change the DMX512 address Once the address has been selected press the ENTER buton to setup to go back to the functions without any change press the MENU buton again Hold and press the MENU buton abo
Download Pdf Manuals
Related Search