Maximum CI 30 Series Professional Digital Decoder User Manual
Contents
1. There are 2 submenus Cl Source and Setup which allow you to set or select the parameters of the Cl CI Source press the lt ENTER gt key then use lt i gt or lt F gt key to select Tuner ASI input or TS IP input the TS IP option is only available when the IP In is set Refer to section 6 4 6 for details When done choosing press lt ENTER gt key to confirm and save or press lt EXIT gt key to discard and exit MAXIMUM 10 Maximum CI 30xx series Receivers Setup under this sub menu you can see all program names from the Cl source that was set in Cl Source previously All free programs are marked with Free in the first row To select which program to be de encrypted press the lt i gt or lt F gt key to roll up and down the program names and press lt ENTER gt key to change the status of the corresponding program only encrypted program could be selected Three different statuses could be set Slot 1 de encrypted with upper CAM inserted Slot 2 de encrypted with lower CAM inserted Bypass no de encryption The status will be shown in the first row on the LCD display Confirm this setup when leaving this sub menu Press lt ENTER gt key to confirm and save or press lt EXIT gt key to discard and exit The de encrypted program could be delivered to other functional blocks such as A V decoder ASI ASI2 SDI Mux Filter and TS IP output refer to section 6 3 3 6 3 6 for more2. After the operation is complete you need reboot the unit to valid the configuration IP In the TS IP port is configured as input You can feed transport stream over IP into the unit The menu Ethernet will be shown under the inputs menu IP Out the TS IP port is configured as output You can set the transport stream over IP output to the IP network The menu Ethernet will be shown under the outputs menu No Exist the TS IP port is invalid Therefore the menu Ethernet will not be shown anywhere Filter Function Press the lt ENTER gt key to activate the menu and use the lt dl gt lt Y gt keys to configure the TS IP functional block to IP In IP Out or No Exist Press the lt ENTER gt key to confirm and save or press the lt EXIT gt key to discard and exit 6 4 7 Setting Machine Type This setting is reserved for factory setting only 7 Remote Monitoring and Control The Maximum Cl 30xx series provides an Ethernet remote control interface for user remote control or supervise on one or multiple Maximum Cl 30xx via the Headend Devices Management System HDMS 7 1 Install HDMS to a PC The HDMS Installation exe file could be found on the CD ROM which is enclosed in the original package Detail information about installation can be found in the HDMS Reference Guide 7 2 Connect to HDMS After installation of HDMS you need to configure the local settings of the Maximum Cl 30xx s whi
3. 6 3 3 Decoder You can configure the parameters of Video and Audio of the program decoded by AV decoder Program under this sub menu you will see all program names detected by 4000P The programs could be coming from ASI input Tuner TS IP input or the internal Cl de encryption block Use the lt gt or lt gt key to roll up or down between the program names and use lt gt and lt M gt key to switch among input sources The character in front of the program name indicates the input source For example A xxxxx the program comes from the ASI input T xxxxx the program comes from the TUNER input xxxxx the program comes from the TS IP input C xxxxx the program comes from the internal Cl functional block xxxxx is the program name A few seconds after the program being selected the A V signal will be delivered to the related connectors on the back panel Video You can configure the video parameters of programs in this submenu Press the lt ENTER gt key to confirm and press the lt EXIT gt key to cancel Video Standard you can select Auto or SECAM or NTSC or PAL for the composite video output Screen select the screen mode Auto 4 3 Full 16 9 Full or 4 3 Letterbox DVB Subtitle Lang select the language of DVB Subtitle MAXIMUM 1 lt Maximum CI 30xx series Receivers EBU Subtitle Lang select the language of EBU Subtitle Subtitle Priority configure the priority of Subtitle cnoose whether
4. DVB or EBU should be first Close Caption Select OFF will turn off the caption and select ON will turn on the caption VBI Mode Select DISABLE will disable the VBI mode and select ENABLE will enable the VBI mode Audio You can configure the audio settings in the submenu Audio Level use the lt gt lt F gt lt gt lt gt keys to modify the audio level within this range 0 99 Audio Mode select Stereo Left Right or Mono for soundtracks Audio Language select the language of the audio Biss ltincludes Biss Mode Biss 1 Setup and Biss E Setup Biss Mode Set Biss mode can select OFF Biss E or Biss 1 Biss 1 Setup set Biss 1 password is required Biss E Setup set Biss E ID number and password are required 6 3 4 ASI You can configure the settings of ASI in this menu ASI Source Press the lt ENTER gt key and use the lt i gt or lt F gt key to roll up or down to select the signal source of ASI output There are 4 type of signal source optional Cl De encrypted the de encrypted transport stream from Cl functional block will be delivered to the ASI output port on the back panel TUNER the transport stream from Tuner block will be delivered to the ASI output port on the back panel ASI Input the transport stream comes from ASI input port will be delivered to the ASI output port on the back panel Mux TS the transport stream comes from internal Mux Fil
5. IP on the first row the stream itself is Unicast The IP address of the receiving device may be PC with VLC needed to be set to the same unicast address as the one on Maximum CI 30xx Please don t use DHCP to get a dynamic IP address for the receiving device Multicast UDP Port Enter the UDP port number of the TS over IP stream output IPTV mode Max Channels lt 6 you can configure the number of IPTV channel The valid range goes from O to 6 After the configuration you can use lt i gt lt F gt keys to roll up and down between the channels Each channel could be configured independently MAXIMUM 16 Maximum CI 30xx series Receivers Channel x x means the channel number Press the lt ENTER gt key to go down to the sub menu There are 4 sub menus x Multicast IP Enter the IP address of the IP stream for the transport stream over IP output You can also configure the IP stream output mode in Multicast or Unicast by setting Multicast IP address x Multicast Port Enter the UDP port number of the TS over IP stream output x Switch each channel could be switched On Off independently The default value is off To activate the channel you need to set the switch to be on x Program it shows all programs carried by the transport stream from the source selected Press the lt ENTER gt key and use lt amp gt lt F gt keys to roll up and down between the program names where the charact
6. and 8PSK 2 3 3 4 3 5 5 6 8 9 9 10 to choose among Pilot select Off or On according to the actual signal Roll Off Factor you can choose 0 2 0 25 or 0 35 6 2 3 RSSI There are four options to show the quality of receiving DVB S signal 6 2 4 Ethernet Note this menu is showed only when the TS IP streaming board is installed and the board is set to IP In Please refer to section 6 4 6 Optional Function The Ethernet connector is for receiving transport stream over IP The Ethernet connector has user configurable IP address network mask and default gateway These must be set to the appropriate values for the network to work properly Stream IP Addr Enter the IP address for streaming IP input of the unit Stream Network Enter the network sub mask for the subnet to which the unit is connected for IP streaming traffic Stream Gateway Set the gateway for the network to which the unit is connected for IP streaming traffic Stream Mac Address factory set MAC addresses are guaranteed to be unique Therefore you cannot configure the address Multicast IP Addr Enter the IP address of the multicast stream for the transport stream over IP Multicast UDP Port Enter the UDP port number of the TS over IP stream Protocol select the protocol for multicast UDP or RTP Output Smoothing set the quality of TS which comes from the TS IP input Auto the bit rate is variable Disable the unit let
7. output 1 optional RGB output 1xRCA CVBS output 1xRCA 1xBNC Audio XRL Balance Output 1 General Operating Temperature 0 45 C Storage Temperature 20 70 Humidity lt 85 Power Supply AC 90V 260V 50Hz 60Hz Dimensions 483 mmx255 mmx44 mm Approximate Net Weight 4 2 kg 10 Accessory List Maximum CI 30xx 1set CD 1pc Power Cord 1pc RCA A V Cable 1pc BNC Cable 1pc XLR Connector 2pcs MAXIMUM DB Maximum CI 30xx series Receivers This document and the information contained in is the property of KJAERULFF1 DIGITAL A S and may be the subject of patents pending and granted It must not be used for commercial purposes nor copied disclosed reproduced stored in a retrieval system or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise whether in whole or in part without Pro Broadband Inc s prior written agreement 2009 KJAERULFF1 DIGITAL A S All rights reserved Ai id DB
8. 00 Optional FUNCION a od tado eto dotan ral 18 6 47 Setting Macnine Pe a a O 19 7 Remote Monitoring and Control ica a E Woltinmadenkiaces 19 install RDNS o a Pt fe da 19 TZ Conheci o HDM S asia as 19 TS LOJA OD MIS ee 19 TA Add Maximum CI Seco HMDS susana asa ads ga ends ancien ete O a aca 20 725 Maximum CI 3001n IDM Sonia 20 A A 21 O A A A 21 O SpeciicalONa ata ia GAS L anaes aan E O a Rad 21 OPAC COS SON ISLA tla Pte nocget gee EE EERS 23 Maximum CI 30xx series Receivers 1 Before Using the Device Thank you for purchasing the Maximum Cl 30xx series This User Manual is written for operators users of the Maximum Cl 30xx Professional Digital Decoder to assist in installation and operation Please read this user manual carefully before you proceed to install and use the device For Your Safety This equipment is provided with a protective earthing ground incorporated in the power cord The main plug shall only be inserted in a socket outlet provided with a protective earth contact Any interruption of the protective conductor inside or outside the device is likely to cause device malfunction and endanger the users Do not remove the covers of this equipment Hazardous high voltages are present within this equipment and may be exposed if the covers are removed Only KJAERULFF1 DIGITAL A S trained and approved service engineers are permitted to service this equipment No operator serviceable parts inside Refer servicing to K
9. 6 for how to set the Mux Filter function block After the operation the selected transport stream will be delivered to the TS IP function block for further operation Mode select the mode of IP stream you can select DVB or IPTV DVB mode the transport stream which comes from the source selected in the previous step will be packed into IP Stream directly The IP stream will carry all programs and this IP stream will be delivered to specified Multicast or Unicast IP address IPTV mode the transport stream which comes from the source selected in the previous step will be de Muxed to several single programs and each program is packed into one IP stream Each IP stream is then being delivered to specified Multicast or Unicast IP address You can configure up to 6 IPTV channels Multicast Setup use the lt ENTER gt key to enter sub menu The sub menu is different according to different mode selected in previous step DVB mode Multicast IP Enter the IP address of the IP stream for the transport stream over IP output You can configure the IP stream output mode in Multicast or Unicast Multicast could be established by setting Multicast IP address in the range between 239 255 255 255 and 224 0 0 0 Unicast could be established with the same settings of Multicast but there is a difference The IP address should NOT be set in the range between 224 0 0 0 and 239 255 255 255 Although the display is Multicast
10. JAERULFF1 DIGITAL A S trained and approved service engineers For the correct and safe use of the device it is essential that both operating and servicing personnel follow generally accepted safety procedures in addition to the safety precautions specified in this manual Whenever it is likely that safety protection is impaired the device must be made in operative and secured against unintended operation The appropriate servicing authority must be informed For example safety is likely to be impaired if the device fails to perform the intended measurements or shows visible damage WARNINGS e The mounting environment should be relatively dust free and free of excessive vibration The ambient temperature should be between O C to 40 C and the relative humidity is recommended to be between 20 to 80 no condensation occurs e Avoid direct contact with water o Never place the equipment under direct sunlight exposure e The outside of the equipment may be cleaned using a lightly dampened cloth Do not use any cleaning liquids containing alcohol methylated spirit or ammonia etc e For continued protection against fire hazard replace line fused only with the same type e Air intake for cooling is achieved via holes at the side of the device and the fans inside In order to prevent air flow obstruction the device has to be placed on a flat surface leaving some space at the sides of the device e When in operation the internal tempera
11. Maximum Cl 30 Series Professional Digital Decoder User Manual Software Version gt 03 d9 29 2009 08 06 MAXIMUM si Sdigital technology Table of Contents AID CTONS US MANS DECS E EE 1 2 Models that Are Covered by This User Manual occcocccoccncocncoccccocncconococnconnnnnnnnnnnnoncnnnnnos 2 SP e a Dn TA a a a DS Re a 2 ZEM DE CUO q PO e E O 2 92 Operating Vodo O eia e eer e e o olaaa 2 SO OWS OUPO costs ir na a ead cinvaleeredce dsehete gestae ules shales daesienesseucets 3 SF INS FUSES siii 3 29 CONMECIMNG Ne DIU Cr oo eee dieta 3 3 0 ROWeron the DEVICE ca oo a A ap 4 4 Navigatlndo he Frontal a la end 4 Madcat r LEDS ras as is Sa Sia TO GS aes eee ae 4 CD A O DA eaters 5 Es Operation BUNIO sie E a eases 5 AAs COMMON Mena E assis copies tae stain Da A 6 9 FUNCOM BIOCK Diag aM ac ra T 6 SAO a A a a A 6 DENAI MENU E E A ee eee RE T O 2 DONS io a A T O E A tienes T DEZ E AAA e o UU a T 60 22 OPSKCOFDWOAMBPSK dada 8 OARS A A ates aude tas nin a oie eee aon asauaneeowAe 9 CZ NS li iio 9 O O UDS a a a aE 10 DS IDA US seas E a ida a A E ss maneetecden 10 DA E O ad a a a a RA needs a o A A a EE 10 DES DECO CO aa a ga ap aaoomeaamoatdenps aes 11 DO AO A a A e 12 DS DAS CS DI A oo Po ad US apa a 13 Go O IML POLO ii dic 13 A A een aa es 15 A PE PI AA 17 CA Local SC diia dai 18 64 2 Trap PAG OV ass 18 DS UN A A meer cae o o E RD o na 18 O e elo qa AA qn PP DS a a aa 18 BAND Factory SeN S esperno idos 18
12. The lt ENTER gt key is used to enter the main menu or a sub menu When you are at the preferred menu lt ENTER gt is used to active the parameter on the bottom line and allows you to change the value It also finishes the input of new alphanumeric values and confirms the changes The lt di gt and lt F gt keys are used to select between the main menus sub menus or programs When you are at the preferred menu and the parameter is activated they are also used to change the numerical values You may selection the digit using the lt gt and lt P gt keys The lt EXIT gt key is used to exit a menu without any action taking place MAXIMUM 5 Maximum CI 30xx series Receivers 4 4 Common Interface There are two Common Interface slots You can insert up to two different CAM modules for descrambling o Function Block Diagram The chart below shows the complete function block diagram of Maximum Cl 30xx The arrow or dotted arrow indicates the transport stream flow The function blocks embayed in the dotted line are user configurable The TS IP function block is valid when the TS IP streaming board is installed into the Maximum Cl 30xx You can set it as IP In or IP Out which is exclusive to each other refer to section 6 4 6 The Mux Filter function block is standard option and could be configured as internal 2 way multiplexer or filter which is exclusive to each other Also you ca
13. ameters properly If the signal still cannot be locked please check whether the quality of the signal is out of the threshold of the Tuner If none of the above solutions resolves the problem the device might be damaged Please contact a service agent for supports 3 Why can t the ASI be locked Answer Please make sure the BNC cable is well connected and there are programs transmitted to the unit via the BNC cable If the problem remains unresolved please contact a service agent for supports 4 Why can the Maximum Cl 30xx not be connected to HDMS Answer Please double check whether the Ethernet cable is well connected first Also make sure the parameters are set appropriately under Local Setup and the HDSM software is installed correctly in PC which should also be set appropriately and can access the network Maximum CI 30xx is connected to If the problem remains unresolved please contact a service agent for supports 9 Specification QPSK Demodulation amp FEC Parameters Input Frequency Range C amp Ku Band 950 2150 MHz Input Level 25 dBm 65 dBm Input Impedance 75 Q F type Symbol Rate 2 45 Mb s SCPC or MCPC MAXIMUM 212 Maximum CI 30xx series Receivers Rolling Off Factory Punctured Rates Reeds Salomon Decoding DVB C QAM Demodulation Connector Input Symbol Rate Range Demodulation Tuner Bandwidth FEC Decoder Frequency Range Digital Signal Input Level Input Impedance DVB T COFDM Demodul
14. ation Connector 1 IF Loop through Frequency Range Input Symbol Rate Range Constellation Tuner Bandwidth Digital Signal Input Level Input Impedance FFT mode Guard Interval FEC Code Rate DS3 Input Input Impedance Connector Maximum Input Code Rate Format DS3 Loop Through Output Impedance Maximum Output Code Rate Connector Format TS over IP Output Connector Output Bit Rate UDP RTP Multicast Control Protocol 0 20 or 0 35 1 2 2 3 3 4 5 6 6 7 7 8 204 188 T 8 amp 12 IEC Female 7 8 MHz or F Female 6 MHz Input 1 7 Mbs PAL 1 6 Mbps NTSC 16 32 64 128 256 QAM 6 MHz or 7 MHz or 8 MHz factory optional 1 2 2 3 3 4 5 6 7 8 K 7 50 860 MHz 15 15 dBmV 75 Q F type IEC Female 7 8 MHz or F Female 6 MHz Input Yes 470 862 MHz 174 230 MHz 4 98 31 67 Mbit s 8 MHz bandwidth QPSK 16 QAM 64 QAM 8 MHz 20 to 75 dBmV 75 Q unbalanced 2K 8K 1 4 1 8 1 16 1 32 off 1 2 2 3 3 4 5 6 and 7 8 7150 BNC 44 736 Mbit s Unframed Framing according to G 804 G 752 DS3 7150 44 736 Mbit s BNC Unframed Framing according to G 804 G 752 DS3 100 base T RJ45 70 Mbits s Max Multicast or Unicast IGMPV2 MAXIMUM ye I O Interface on back panel Maximum CI 30xx series Receivers LNB I O 1xInput 1xloop through output RS 232 1x9 pin D sub male 1xEthernet control port 1xTS over IP output RJ45 l factory optional ASI input 1 ASI output 2xRedundant output SDI
15. ch is are expected to be connect to the remote control network Please refer to section 6 4 1 7 3 Login to HDMS To login on HDMS a user account and password are needed Default user account is hdms password is hdms You can create or delete new accounts Detailed information can be found in the HDMS Reference Guide MAXIMO 19 Maximum CI 30xx series Receivers 7 4 Add Maximum Cl 30xx to HMDS Make sure the Maximum Cl 30xx are well connected with the network which the PC with HDMS installed can access the Maximum Cl 30xx Press the E icon in the top left of the window in HDMS and the system will start searching the Maximum Cl 30xx automatically The device found will be displayed in the Devices Window in HDMS When a new Maximum Cl 30xx is added to the remote control network you can press gt to refresh the network The new added unit will be added into the HDMS automatically For other methods for adding one or a group of Maximum CI 30xx please refer to the HDMS Reference Guide 7 5 Maximum Cl 30xx in HDMS Double click on the device in the Devices Management window to open the console of the Maximum Cl 30xx The HDMS provides full operation to the Maximum Cl 30xx Parameters are grouped in three panels The Input Setting provides the full operation on inputs parameters The Output Setting allows the full operation control functions on outputs parameters The System Setting shows the general device managem
16. d below must be set to appropriate values for the network that the transport stream over IP is broadcasted Stream IP Addr Enter the IP address for streaming IP output of the unit Stream Netmask Enter the network sub mask for the subnet to which the unit is connected for IP streaming traffic Stream Gateway Set the gateway for the network to which the unit is connected for IP streaming traffic Stream Mac Address factory set MAC addresses are guaranteed to be unique Therefore you cannot configure the address Protocol select the protocol for multicast UDP or RTP TS Pkts per UDP set the number of the TS packages encapsulated in one UDP package The valid range goes from 1 to 7 Time to Live set the number of the routers over which the TS over IP can be transmitted The valid range goes from 1 to 5 Type of Service select the type of service There are Normal Min Monetary Cost Max Reliability Max Throughput or Min Delay optional Source select the source of the transport stream over IP streaming output There are 4 type of source optional ASI Input Cl De encrypted TUNER Mux TS note the Mux TS is showed only when the Mux Filter function block is enabled and turned on The Mux TS indicates not only the after multiplexed TS when Mux is enabled but also the after filtered TS when the filter is enabled Refer MAXIMUM 15 Maximum CI 30xx series Receivers to section 6 3 6 and section 6 4
17. ent parameters Each console has four control buttons Apply to apply the current settings for the unit which is being accessed Refresh to obtain the current settings from the unit Load to load the pre settings files to the HDMS and press Apply to apply the pre settings for the unit Save save the user s settings as an xml file Remark When duplicating the configuration of one device to the other unit s you need to modify the System Setting such as IP address gateway Unit name etc manually after loading the xml file dr da 20 Maximum CI 30xx series Receivers 7 6 Other Settings The HDMS provides Alarms management Devices management and User accounts management It may also be necessary to modify some of the other settings to suit the particular installation Please refer to the HDMS Reference Guide for more information FAQ 1 Why there is nothing shown on the LCD Answer Please check whether the power supply is well connected first If not please reconnect it and turn on the device If there is still nothing displayed on the LCD the unit may be damaged Please contact a service agent for technical supports 2 Why can t the QPSK QAM COFDM DVB S2 signal be locked Answer Please double check whether the input cable is well connected first If not please reconnect it If it is connected well please check whether all the necessary parameters are set properly If not please set the par
18. er in front of the program name indicates the input source A xxxxx the program comes from the ASI input T xxxxx the program comes from the TUNER input xxxxx the program comes from the TS IP input C xxxxx the program comes from the internal Cl function block xxxxx is the program name All encrypted programs are labeled with a sign on the first row Press the lt ENTER gt key to selected the program you wish to be delivered to the specified IPTV channel Press the lt EXIT gt key to exit the settings 6 4 System The system menu provides information about the general functions the surroundings equipment and the hardware being used Optional Machine Function Type Figure 6 4 System Menu MAXIMUM 17 Maximum CI 30xx series Receivers 6 4 1 Local Setup Each Maximum Cl 30xx has an IP address a network sub mask and a gateway These parameters must be set to appropriate values so that the unit can be accessed by the remote control system for example HDMS IP Address The IP address for the unit Network Mask The network mask for the subnet in which the unit is connected to Gateway The gateway for the network in which this unit is connected to 6 4 2 Trap IP Addr The Maximum Cl 30xx provides a Monitor Center IP address You can set this to be the same IP address of the Monitor Center which is typically a PC in order to allow the device to send messages to the monitor center If the Maxi
19. he inputs signals under the status menu ASI Input locked or unlock indicate the status of the ASI input Tuner Input when the QPSK QAM COFDM signal is locked by the tuner the bit rate is displayed on the bottom row of LCD de da ae Maximum CI 30xx series Receivers Ethernet this indicates the status of the transport stream over IP input The bitrate is displayed on the bottom row of the LCD only if IP input is valid note this menu is showed only when the TS IP streaming board is installed and the board is set to IP In refer to section 6 4 6 Optional Function 6 2 2 QPSK COFDM QAM 8PSK The tuner setting menu is different and exclusive for different DVB S S2 DVB T DVB C tuner deployed To receive the QPSK COFDM QAM 8PSK signal the relative parameters below must be set to the appropriate values for the receiving antenna to receive the signal QPSK LNB Local Oscillator L O Freq enter the frequency of the LNB in MHz Satellite Freq edit the satellite down link frequency in MHz The IF frequency will be calculated automatically Symbol Rate enter the QPSK symbol rate LNB Voltage select the correct LNB voltage output of the F connector Off 13 V 18 V lt A gt LNB 22KHz activate the LNB 22 kHz control signal to the LNB On or Off lt B gt DISEQC User can select Port A Port B Port C Port D or DISEQC OFF Note please contact the local satellite operator for the satellite frequency and symb
20. ical Table 3 1 Power Requirement of Maximum Cl 30xx Series MAXIMUM e Maximum CI 30xx series Receivers 3 3 Power Supply The power cord is inserted to an IEC main socket which is located at the side of the device A standard power cord with a European DIN 49441 two pin main plug is delivered along with the device 3 4 The Fuses The line fuse is housed in a small container beside the power connector on the rear panel To check the fuse insert the tip of a screwdriver in the slot at the middle of the container and pry gently to extend the fuse where there is a little tap Then pull out the fuse gently The fuse should be attached to the line module and cannot be removed The recognized recommended fuses are size 5 by 20 mm rate T 2 0A 250 V UL and IEC approved 3 5 Connecting the Device Always use the specified cables supplied for signal integrity and compliance with EMC requirements The rear panel is directly related to the input and output options fitted The figure below shows a typical rear panel LAR rr EJ I ooo 000 LJ TUNER GUT TUNER IN L AUIDIO R ASIN ASUS ASI ETHERMET Bi4 B15 B16 B17 Big B19 B20 B21 Figure 3 2 Rear Panel of Maximum Cl 30xx Series B1 TSolP interface not available on Maximum Cl 301x B2 XRL L interface B3 XRL R interface B4 RGB YUV interface G Y B5 RGB YUV interface B U B6 RGB YUV interface R Y B7 CVBS2 Output interface B8 B18 ASI2 SDI output inte
21. mum CI 30xx Series 4 1 Indicator LEDs There are 3 LED indicators POWER the status of the power supply green the power is turned on MAXIMUM si sdigital technology 4 Maximum CI 30xx series Receivers off the power is turned off TUNER LOCK the status of the tuner green the incoming QPSK is locked by the tuner off there is no QPSK input signal or the signal is unlocked ALARM the status of input signal source which includes IP input QPSK signal input and DVB ASI TS input 4 2 LCD The 2 x 20 character Liquid Crystal Display LCD shows all the required information about the selected parameters The top row of the LCD shows the selected parameter The bottom row indicates the present values and how these can be adjusted The parameters are grouped in three menus the Inputs which provides the full operation on inputs parameters the Outputs which provides the full operation control functions on outputs parameters the Systems which provides the general device management parameters and informs the device working status When the label gt is shown in the right side on the second row it indicates you can use lt ENTER gt key for further navigation in sub menus 4 3 Operation Buttons VIUDO Figure 4 2 Keypad of Maximum Cl 30xx series The 6 keys on the front panel allow you to navigate the information provided on the LCD and change parameters when the device operates under local control
22. mum Cl 30xx is connected with the HDMS remote management system the Trap IP address is typically set to be the IP address of the PC where the HDMS has been installed 6 4 3 Unit Name The Maximum Cl 30xx allows you to edit the unit name which is displayed on the front panel LCD The default name is Digital TV Processor The unit name should not be longer than 20 characters in ASCII format 6 4 4 Properties You are allowed to check the properties information of the device MAC address Factory set MAC address is guaranteed to be unique You cannot configure this address FW Version the version of the FPGA software note that this version number will be changed automatically according to the TS IP settings IP In or IP Out SW Version the version of the main software 6 4 5 Factory Settings All the user configurable parameters will be set to the factory default settings including IP address and the unit name Note the unit will not be connected with the HDMS remote management system until the IP is properly configured 6 4 6 Optional Function There are two submenus External Board Type Press the lt ENTER gt key to activate the menu and use the lt i gt lt Y gt keys to configure the TS IP functional block to IP In IP Out or No Exist Press the lt ENTER gt key to confirm and save or press the lt EXIT gt key to discard and exit MAXIMO 18 Maximum CI 30xx series Receivers
23. n turn on or off the block refer to section 6 4 6 Tuner Input Port MPEG 2 AN Decoder Buffer ASI Input Port AO A run TS Switch Matrix gt de Y U O S LO S O O 3 em G nnee y Mux Filter option Keyboard Menu display and LAN control Figure 5 1 Maximum CI 30xx Function Block 6 Start to Use The device allows you to configure control and monitor through the Keypad and front panel display when a remote control system is not used MAXIMUM 0 Maximum CI 30xx series Receivers 6 1 Main Menu Turn on the device and wait for 8 to 10 seconds During this period the device will complete self inspection and configuration The name of the device will be displayed on the top row of the LCD and the local IP address will be displayed on the bottom row of the LCD Note the local IP address and unit name can be changed in the System Menu refer to section 6 4 1 and 6 4 3 System Use the lt ENTER gt key to enter on the Main Menu The lt 4 gt and lt F gt keys are used to choose between the three main menus Figure 6 1 Main Menu Structure 6 2 Inputs Under Inputs Menu you can monitor and configure the parameters of the Tuner and TS over IP input only when the TS IP streaming board is installed and the board is set to IP In refer to section 6 4 6 Optional Function Figure 6 2 Inputs Menu Structure Ethernet option 6 2 1 Status You can monitor the status of t
24. ol rate lt A gt Normally 13V switches the LNB to receive Vertical Left hand polarization while 18V receive Horizontal Right hand lt B gt Normally 22KHz control signal switches the LNB to receive high band if any COFDM Frequency enter the proper frequency of the COFDM signal in MHz QAM Constellation enter the modulation mode of the QAM signal Frequency enter the frequency of the QAM signal in MHz Symbol Rate edit the symbol rate to the proper value in KBaud 8PSK LNB Local Oscillator L O Freq enter the frequency of LNB in MHz Satellite Freq edit the satellite down link frequency in MHz The IF frequency will be calculated automatically Symbol Rate enter the QPSK 8PSK symbol rate MAXIMUM 8 Maximum CI 30xx series Receivers LNB Voltage select the correct LNB voltage output of the F connector Off 13 V 18 V lt A gt LNB 22KHz activate the LNB 22 kHz control signal to the LNB On or Off lt B gt Note please contact the local satellite operator for the satellite frequency and symbol rate lt A gt Normally 13V switches the LNB to receive Vertical Left hand polarization while 18V receive Horizontal Right hand lt B gt Normally 22KHz control signal switches the LNB to receive high band if any Demodulation Mode select the DVB S or DVB S2 demodulation mode Operation Mode select the appropriate operation mode in the menu There are QPSK 1 2 2 3 3 4 4 5 5 6 8 9 9 10
25. ome from the selected source in previous step The programs could be come from ASI input Tuner TS IP input or the internal Cl de encryption block Use lt i gt lt gt keys to roll up the program names where the character in front of the program name indicates the input source A xxxxx the program comes from the ASI input T xxxxx the program comes from the TUNER input xxxxx the program comes from the TS IP input C xxxxx the program comes from the internal Cl function block MAXIMUM 14 Maximum CI 30xx series Receivers xxxxx is the program name On Filter List sub menu all programs that are being selected to be filtered away are labeled as Forbid otherwise the un selected programs are labeled as Pass Use the lt ENTER gt key to selected or un selected the program being shown When exiting the Filter List sub menu a new menu will be shown Confirm changed Press the lt ENTER gt key to validate all programs just be selected to be filtered away or press the lt EXIT gt key to discard the settings After a few seconds the filtered TS will be generated and delivered to the specified destination s 6 3 7 Ethernet Note This menu is shown only when the TS IP streaming is installed and the board is set to IP Out Refer to section 6 4 6 for more details The TS IP Ethernet connector could also be configured as the output of the transport stream over IP The parameters liste
26. rface 75 ohm female BNC connector B9 B19 ASI1 output interface 75 ohm female BNC connector B17 ASI input interface 75 ohm female BNC connector SA Pa RE th pa i Li AS ae oo ile A Ii A Y Die Maximum CI 30xx series Receivers B10 RS 232 interface B11 Tuner Loop Out interface B12 Tuner In interface B13 Power socket AC 90 260V B14 CVBS1 Output interface B15 B16 L Audio R interface B20 Ethernet interface for remote management system B21 Grounding Note This RS 232 interface is a 9 pins female sub D connector that is only used for factory software upgrade and configuration You may not connect any cable to the RS 232 connector as that could cause damage to the device 3 6 Power on the Device Make sure the device is mounted into the rack properly and firmly and the signal cables are well connected before applying power to the device The main socket and fuse are located at the rear panel of the device After the device is powered on check if the following message presents on the display on the front panel Maximum Cl 30xx factory default unit name IP 10 10 60 148 factory default IP Address for LAN access If no message is presented or there is no light on the display the device is defective and has to be returned for servicing 4 Navigating the Front Panel Power Tuner Lock Alarm LCD Keyboard Common Interface 1 MAXIMINI hal bdigitad seah ribage Figure 4 1 Front Panel of Maxi
27. rograms are labeled with a sign All programs being selected to be re multiplexed are labeled as Pass otherwise the un selected programs are labeled as Fobrid Use lt ENTER gt key to selected or un selected the program being shown When leaving the Mux List sub menu a new menu will be shown Confirm changed Press the lt ENTER gt key to validate all programs just be selected to be multiplexed or press the lt EXIT gt key to discard the settings After a few seconds the multiplexed TS will be generated and delivered to the specified destination s Filter function description Filter Switch the internal filter could be switched On Off The default value is off To activate the filter function you should turn on this filter functional block Bit Rate should be set to a specified value that does not exceed the Maximum physical limit of the output medium otherwise overflow occurs Source Press the lt ENTER gt key and use the lt i gt or lt F gt key to roll up or down to select the signal source of filter function block there are 4 type of signal source optional Cl De encrypted TUNER ASI Input TS IP input only available when the TS IP is set IP In Refer to section 7 4 6 for details Use lt ENTER gt key to save or press lt EXIT gt key to discard Program List Press the lt ENTER gt key to enter Filter List sub menu It shows all programs carried by the signal c
28. ter functional block will be delivered to the ASI output port on the back panel The Mux TS is valid only when the Mux Filter function block is enabled and turned on The Mux TS indicates not only the after multiplexed TS when Mux is enabled but also the after filtered TS when the filter is enabled Refer to section 6 3 6 and section 6 4 6 for how to set the Mux Filter function block Press lt ENTER gt key to save or press lt EXIT gt key to discard A few seconds after the source is selected the TS will be delivered to the ASI output port on the back panel MAXIMUM le Maximum CI 30xx series Receivers ASI Package Length you can configure the package length of ASI output as 188 bytes or select Bypass 6 3 5 ASI2 SDI You can choose between ASI output and SDI output If the port is configured as ASI2 the configuration method is the same as ASI refer to section 6 3 4 If the port is configured as SDI there are two parameters which need to be set Audio PID and Embed Audios Audio PID press the lt d gt lt F gt keys to choose the audio PID from 1 4 Embed Audios there are 4 options none one amp two two and one 6 3 6 Mux Filter The Mux or Filter menu is shown only when the Mux Filter function block is enabled and turned on The Mux Filter are alternative refer to section 6 4 6 for how to turn on and set the Mux Filter function block Make sure the s w supports Mux Filter func
29. the TS pass by Fixed Rate the bitrate is fixed MAXIMUM O Maximum CI 30xx series Receivers TS Bit Rate set the bit rate of the TS comes from the TS IP input The setting is only valid when the output smoothing is configured as Fixed Rate 6 3 Outputs Under Outputs Menu you can monitor and configure the parameters of Cl AV decoder ASI out ASI2 SDI out Mux Filter A and TS over IP output B A The Mux Filter menu is showed only if the functional block is enabled Refer to section 6 4 6 B The menu is showed only if the IP streaming in out board is installed and the TS IP streaming board is set to IP Out Refer to section 6 4 6 Outputs ASI2 SDI Mux Filter Ethernet option Figure 6 3 Ouiputs Menu Structure 6 3 1 Status There are 3 displays on the LCD for monitoring the status of the decoder the common interface Decoder OK or Alarms indicates the status of the decoder You can use the lt ENTER gt key to check detailed information in the submenu of the Decoder Cl You can check the information of the CAM Modules in Slot1 and Slot2 6 3 2 Cl There are two PCMCIA slots for inserting CAM for de encrypting program from the input signal Before setting Cl make sure the signal from ASI input is locked or the Tuner locks is on the correct Transponder this depends on which signal the encrypted program carries The Tuner Lock green LED should be on when CAM is inserted
30. tion The earlier s w has masked the Mux Filter function After s w 03 9a xx this Mux Filter function has been unmasked Mux function description Mux Switch the internal multiplexer could be switched On Off The default value is off To activate the re Multiplexing function you should turn on the Mux functional block Bit Rate should be set to a specified value that doesn t exceed the Maximum physical limit of the output medium For example to deliver the multiplexed TS to an 8MHz DVB 256QAM modulator it should not exceed 55000Kb s otherwise overflow occurs TS ID you can configure the TS ID to mark the multiplexed TS The default value is 1 Program List press the lt ENTER gt key to enter Mux List sub menu It shows all programs detected by Maximum Cl 30xx The programs could be come from ASI input Tuner TS IP input or the internal Cl de encryption block Use lt i gt lt F gt keys to roll up the program names and use lt i gt lt P gt keys to switch among input sources where the character in front of the program name indicates the input source A xxxxx the program comes from the ASI input T xxxxx the program comes from the TUNER input xxxxx the program comes from the TS IP input C xxxxx the program comes from the internal Cl function block MAXIMUM 13 Maximum CI 30xx series Receivers xxxxx is the program name On Mux List sub menu which is on the first row all encrypted p
31. ture should not exceed the limit of 70 C MAXIMUM 1 Maximum CI 30xx series Receivers 2 Models that Are Covered by This User Manual Model No Maximum CI 30xx o o Mammolo OOO O O ToP mm DVBSinput mT DVBTinput mT Jm DVB C Input m DVB S2Input m m PCMCIA Slot 2 0 ASI Input Output PM SDI Output audio embedded Ethernet Remote Control MM w O O CVBS Video Output A V Output RCA 1 Balance XRL Audio Output Simulcrypt Compliant Where the m sign represents standard option Table 2 1 Model list of Maximum Cl 30xx series 3 Installation 3 1 Inspection Open the packaging box Check if all appendixes are in the box according to the appendix list and if the device has any visible damage Check that the power cord is suitable for the country where the device will be used Please contact the agent if there is any damage or appendix missing 3 2 Operating Voltage Do not connect AC power until you have verified that the line voltage is correct and the proper fuses are installed The power supply of the device is fitted with a wide range power supply It is suitable for supply voltages of 100 240 Vac 10 6 at 50 60 Hz nominal Please make sure the supply voltage is within the specified range POWER REQUIREMENT Input voltage 90 250 Vrms auto select Frequency 47 to 63 Hz Power 50 VA max 30 VA typical Current 110 V 0 27A or 240 V 0 125A typ
Download Pdf Manuals
Related Search