GSM Doorbell User Manual
Contents
1. If there is any doubt or disputable regarding information in this manual you can call our company for clarification In all cases for more details please refer to the electronic user s manual on the included Thanks MC 1142 A 2 OPERATION INSTRUCTION GSM Doorbell User Manual 4 Safety Instructions Read these instructions and keep them in a safe place for future reference Please refer all work related to the installation of this product to qualified service personnel or system technician Do not operate the appliance beyond its specified temperature humidity or power source ratings Securely install the devices on vertical surfaces solid walls doors not prone to vibration or impact Install the devices away from heat sources such as radiators heat registers and stoves Installation of the terminal near consumer electronics devices e g stereo receiver amplifiers and televisions is permitted as long as the air surrounding the terminal does not exceed the above mentioned temperature range X Handle the appliance with care Do not strike or shake as this may damage the device X The doorbell camera units should be fitted with an approved weather shield if the chosen position is in direct sunlight or in contact with rain snow or irrigation sprinkler systems X Do not use strong or abrasive detergents when cleaning the appliance body When the dirt is hard to remove use a mild detergent and wi2. 2 holes according to the bracket embed 2 plastic anchors into the holes Hole e Plastic anchor 3 Drag the connection cable of the device through the round hole on the bracket 4 Use a screwdriver to affix the bracket with the installation screws mg Installation screws 2 4 Feature Pho Name peseriptions 1 Speaker Sound from smart phone 2 Microphone Transmit voice to telephone 3 Signal indicator Signal indicator of GSM card 4 Call button Visitor call for intercommunication If the GSM SIM card has been inserted to the 5 Call button indicator device the indicator will be flashing as blue when press the call button 6 GSMcard slot To insert the GSM card to the device J Set up about the GSM Doorbell 1 Remove the rubber plug on the back of the device and insert the GSM card 2 Connect the door lock to the doorbell according to section 2 2 Wiring Diagram of the GSM Doorbell and power on the device When the device is powering on the button indicator light will show a steady blue and the signal indicator light will show a quick flashing green When the doorbell has detected and registered to the GSM network then the button indicator light will turn off and the signal indicator will show a slow flashing green 3 Set password The default password is 888888 For safety please first change default password to user s own password Note the password must be six numbers between 0 9 Send a SMS text
3. e lock is kept under constant closed state If the unlocking button is pressed and the dry contact is changed to closed then the lock is released 2 3 Installation process of GSM Doorbell E 5 3 amp 3 B AN NOTE Avoid installation of the device near strong radiation e g AC monitor and lift Maintenance should be complied with qualified technician Avoid hard shake beating and collision otherwise the internal exact components maybe be damaged Do not expose the outdoor camera under strong light or sunshine Do not install the device in the environment e g direct sunlight contact rain High temperature high humidity full of dust and chemistry corrosive Select the most suitable position where the device is located at user s mouse Switch off power supply before installation Keep more than 30cm away from AC power supply to avoid external interference Keep it away from the water and magnetic field To install the GSM doorbell please follow steps as below Surface mount RR EEEE RY ge a Sas 7 lt Q Plastic anchors Connection cable j Bracket amp Rubber plug Plastic anchors Connection cable Rubber plug Bracket Please follow these steps as reference 1 Remove the rubber plug on the back of the device insert the SIM GSM card 2 Select the most suitable position where the GSM doorbell is located at user s eye level then drill
4. l receive a message PHONE error How to clear the phone numbers have been setting on the doorbell User can set up new numbers to instead of the previous numbers How to handle international numbers For instance call Hong Kong from China 00852 or 852 7E How to use the GSM Doorbell 1 When some visitor press the call button on the GSM doorbell the first preset mobile phone number will receive an incoming call Answer the phone and talk to the visitors To open the electric lock or magnetic lock if installed press the key on user s keypad and then hang up While the doorbell is busy trying to call from dialing the phone number all the way through to hanging up the telephone the button indicator will keep slowly flashing blue If the door is opened by pressing key then the call button indicator will first show a steady red for about 3 seconds then quickly flashing blue When some visitor press the call button on the doorbell it will automatically dial up to the phone numbers in sequence If the first phone hangs up or does not answer the system will call the second phone automatically and then the third phone If the first phone answers the second and third phone will not be called Note If one of the phone numbers has voice mail and the call from the doorbell has transferred to this phone then the doorbell will assume the voice mail that means the user has picked up the phone Therefore s
5. message to the GSM card inside the device Command 1 the old password the new password not including For example 1 888888 123456 where 123456 is the new password If successful the indicator bellow the call button will turn steady red for 1 second and user s mobile phone will receive a reply message PWD 123456 If failure user s mobile phone will receive a message PWD error 4 To set up phone numbers those the doorbell will call in the future those phone numbers can release the door lock connecting to the GSM doorbell via mobile phone directly and up to three phone numbers can be set 5 Set phone numbers for unlocking Up to 3 phone numbers can be set Send a SMS text message to the GSM card inside the device Command 2 password number 1 number 2 number 3 not including Note The password must be correct otherwise the phone numbers will no effect If only one or two numbers are set users must space the telephone numbers with please indicate with or for example as below For example 2 888888 13277889999 13311112222 18622223333 or 2 888888 13277889999 13311112222 or 2 888888 13277889999 If successful the indicator bellow the call button will turn steady red for 1 second and user s mobile phone will receive a reply message PHONE 13277889999 13311112222 18622223333 PHONE 13277889999 13311112222 PHONE 13277889999 If failure use s phone wil
6. pe gently X Do not overload outlets and extension cords as this may result in a risk of fire or electric shock Distributing copying disassembling reverse compiling reverse engineering and also exporting in violation of export laws of the software provided with this product is expressly prohibited Y Description Of GSM Doorbell 2 1 Fitting of the GSM Doorbell GSM Doorbell 1pcs Plastic anchor 2pcs Installation screws 2pcs Affixation screws 1pcs Bracket optional 1pcs This user manual 1pcs External Switching Power Adapter 1pcs 2 2 Wiring Diagram of the GSM Doorbell External switching power supply DC 12V Electric lock 1 RD DC 12V 2 not include 2 BK GND 4 7 3 YE NO 4 BN COM ACIDC power 5 BU NC aia supply for unlocking not included Note RD Red BK Black YE Yellow BN Brown BU Blue The terminal is defined functionality as below 1 RD DC 12V 2 BK GND 3 4 YE BN NO COM To door lock with normally open 4 5 BN BU COMINC To door lock with normally closed User can connect electric lock or magnetic lock to the doorbell Electric lock could connect with NO and COM magnetic lock could connect with NC and COM Dry contact In the standard delivery the system support locks with Normally Open N O and Normarlly Closed N C door unlocking method It means that in the normal state the dry contact marked as is opened so th
7. ubsequent phone numbers will not be called 4 How to unlock through the GSM doorbell actively There are two methods 1 Send a SMS text message to the GSM card inside the device Command the password not including For example the password is 888888 send a message 888888 to unlock 2 Call the phone number of the GSM card via user s mobile phone and the GSM doorbell will answer automatically input correct command on user s phone command the password not including if the password is 888888 please input 888888 If unlocking successfully the call button indicator will first show a steady red for about 3 seconds Visitor can long press the call button on the doorbell to hang up directly after calling How to reset password and delete phone numbers If user forgets the system password he must open the plastic rear cover Unscrew the PCB board and find the button which is named as sw2 Plug the PCB board into power and press the button for about 5 seconds The button indicator will turn red which means the system password has restored to default password 888888 and previous phone numbers have been deleted a
Download Pdf Manuals
Related Search