User Manual for
Contents
1. I sm ETEN me pe koroke gt SD OG CFS ROE e i 2 R PR s Hop os PLUG THE HDD SSD BOX Pull and plug the hard disk box will need to do the following The need to get this effect Plug the HDD SSD box shrapnel and the handle pressed 15 Hard Disk Mobile DVR User Manual V2 0 TT HDD CASE a Screwdriver to secure the HDD KM3 5mm 4X Note when the HDD SSD is installed SIM card is located on the communication board move the small baffle at the bottom of the mainframe you can see the interface of SIM card If system support wireless network communication need install SIM card SIM card and SIM are in the same location you can see them just when you move the baffle at the bottom of the mainframe 16 3 1 Remote Control PTZ control Enter Exit Return System intormation 4images segmentation PTZ Control Key area Hard Disk Mobile DVR User Manual V2 0 3 Remote Control Function Instruction MO PALEY PLAY NET A m gt Mm RON ME Fwi i JECORO ETOP FRAME GOTO O a PIZ PHESET HALL BALE AUTO LOGIN Number key area Subtraction adjustment Direction key area Delete Cancel Play back operation key area Shortcut key test key There is no control button on MDVR panel need remote control to fit operating Key press amp function as below Digit keys zone 0 9 key Und2. NT PTZ SETUP WIRELESS SETUP WIFI SETUP Baudrate Data Bit IO stop Bit 1 Check Address WIFI setting 8 1 PTZ Settings 1 Channel selection 1 4 or 1 8 2 Protocol divided into PELCO D and PELCO P protocol 3 Baud rate 1200 2400 4800 9600 four options the user can modify baud rates according to different PTZ setting 4 Data bit Generally it is 8 where you can select from 1 to 8 but it is 8 by default 5 Stop bit Stop bit is generally 1 you do not need to modify default 6 Check check bit is to select the check way Generally it is chosen to be None 7 Address the address code is input directly by the address corresponding to PTZ setting they must be setting corresponding to the default address code of most PTZ is 1 PTZ has adjustable address code DIP and it is needed to set different address codes to identify when there are numbers of PTZ 8 Wiring method PTZ cathode connected to RS485 A negative connected to RS485 B When PTZ relevant parameters are set ready the remote control can only be used to control PTZ after the channel connected to PTZ is selected for example PTZ is connected to Channel 2 then you can 35 Hard Disk Mobile DVR User Manual V2 0 only control it by switching to 2 channel to maximize it on the monitor interface 8 2 3G 4G settings 36 46 SETUP Description When the MDVR wants to use 3G 4G network reporting platform it needs network related settings in this menu 1 Accor
3. 4HD1 4CIF options 8CH 6D1 8HD1 8CIF options Image Resolution Video Compression H 264 Main profile CIF 1536Kbps 128Kbps HD1 2048Kbps 512Kbps Video bit rate Image Processing amp D1 4Mbps 1Mbps 8 levels optional Highest 1 level Lowest 8 level Storage Audio Compression ADPCM G 726 G 711 options Audio Bit rate 8KB s Support One HDD SSD Max 1TB Support One SD Card Backup when HDD SSD is error Storage Support Mirror Recording with a expand Fireproof Box of SD Optional 8 digital level inputs below 4V is low level alarm above Alarm input ee 4V are high level alarm Alarm Alarm output 2 digital level outputs output voltage level 12V RS485 Interface Support 1 RS485 interface 24PIN Communication RS232 Interface Interface Support 1 RS232 interface Can be connected to digital voice intercom WIFI Interface Support 802 11b g n 2 4G internal or 5 8G external WIFI 6PIN Extended Support 2 RS485 interface Support connecting LCD control panel via extended interface interface Optional 3G 4G HSUPA HSDPA WCDMA EVDO Optional or FDD LTE TDD LTE Optional Built in GPS module Geographical coordinates soeed can be recorded in hard GPS disk and also can be transmitted to CMS Acceleration Sensor Playback Software is used to playback video file GPS Software Playback track G sensor and alarm information Embedded acceleration sensor Hard Disk Mobile DVR User Manual
4. A It means the signal is valid if the GPS module already positioned there may many reasons for the deviation such as government restrictions permissible error GPS signal interruption etc the actual satellite map may have deviation for security reasons general map can solve the problem by using GPS correction 3G wireless module Q If use the 3G 4G wireless module for dial up what do need to pay attention to A 1 Choose the built in wireless module WCDMA EVDO TD SCDMA FDD LTE TDD LTE corresponding module settings are not the same the modules supported by different machines models are not the same so please make sure whether your module and SIM is in correspondence Do not use EVDO SIM card on WCDMA machine 2 Check whether the settings of Server IP and port are correct whether 3G 4G signal is strong enough for dialing and then check whether the 3G 4G dial up is successful or not 3 When dialing is unsuccessful please check 3G 4G antenna is in good contact or not the dial up may fail because of weak signal moreover please check whether the SIM card has enough traffic if no traffic dial up will be unsuccessful Q When 3G 4G has neither report nor video what should be done first A Press INFO key to enter the system information page check whether the SIM card exists and view the signal strength as well as dial up status whether the antenna is in good contact and then check the SIM to see whether it is out of traffic the
5. N Ty 3 A f IN i Video line o The power input of the PTZ Figure 4 6 Fifthly there are three ways of wiring the first way is connecting the 485 control wire to the wire 485A and 485B on host connecting the video cable to the host video input and then provide power to PTZ this kind of wiring needs to set the MDVR host data be corresponding to PTZ data and then use the remote controller or platform to remotely control PTZ The second way the head of the 485 control wire directly connect to the three dimensional control keyboard do not need to connect the MDVR host the video cable connects to the host video input separately power supply to the PTZ and three dimensional keyboard and then set the keyboard parameters to be corresponding with PTZ This wiring way is the most practical one because it uses three dimensional keyboard to control PTZ which is faster easier and more practical It is recommended to use this way to install PTZ The third way is to connect to both car host and three dimensional control keyboard so that both can be controlled and platform remote can also be controlled 3 5 PC playback of the video file You must install Ext3 format driver of HDD Ext2Fsd 0 51 when you read HDD on your computer first Double click installation files within MDVR Player Exe and then select the installation language support Chinese and English and click OK and then click Next to install the playe
6. s device number System Menu General Settings Vehicle Information Device Number device number range is from 00000 to 99999 Server identifies the host according to the device number so it is very important to modify the device number lf the modified device number cannot be reported sometimes please check the server device number has been used or not Step 3 Modify the vehicle identification number the vehicle information displayed on gServer platform is based on vehicle identification number If itis not modified it will display 00000 in default If all are in default it would cause inconvenience to find vehicles So itis proposed to modify the vehicle identification number Step 4 Enter another menu settings System Menu General Settings Network Settings set the server IP and control port the server can be self built and can be affiliated to the manufacturer s server as well enter the server IP and control port which is typically 6608 the save by end The main process of gServer quick reporting is as Figure 3 10 below Installin Modify the the SIM car device NO gServer Client gServer manage rn Username assigned Client viewing re fue IN FO key query Setup the server address and port Modify the icense plate number I 3G settings Step 5 Enter the system menu peripheral wireless broadband which is with wireless settings inside
7. which is a little complicated to operate simple wiring in Figure 3 5 SPEED A Pulse sensor SPEED B gt i Figure 3 5 C The acceleration alarm recording system menu alarm settings acceleration Impact acceleration can be understood to be for three dimensional XYZ coordinate axis which can denote three groups of status up and down left and right front and rear the bouncing up and down accelerate Emergent brake rollover sharp turns etc during the moving process of the vehicle can all be expressed in XYZ Threshold needs to be set by an associated value it is firstly needed a calibration after the installation onto the vehicle the calibration means to clear parameters X Y Z secondly measure the allowed range of emergent brake amp acceleration amp bouncing up and down as well as the change value of a sharp turn of the vehicle during the operation thereby to determine which axis s value changes alot These run status will be in real time display and change After setting the threshold when the vehicle runs exceed above threshold the alarm will be uploaded if the alarm opens D Motion detection alarm recording System Menu Alarm Settings Motion Detection Turn on the motion detection enabled switch set the sensitivity level of high medium and low based on the need general settings is medium and the next step is mostly to set the sensing area of the motion detection motion detection area w
8. SIM card check whether the antenna is in good contact If it still can not report when above all are checked enter into the system information page to view dial up If dial up is not successful look up whether the setting of data access point and center number is correct If all ultimately fail please collect as much information as possible to submit to the technical supporting staff for analysis the more data provided the more convenient for technicians to solve the problem Q The device is online but why can I not see the video image A Please set lower sub stream to transmit image the blocked or slow transmission speed situation may occur when the sub stream frame rate is set very high and be affected by network uploading limit poor network signal or intermittent will seriously affect the video transmission Q The device is properly reported on CMSServer but the videos cannot be seen after using for some time A Firstly check whether the host side displays dialing if it keeps the dialing status it may be because the flow of the SIM card has run out replace the SIM card to test Secondly query whether the host device number has been modified by the driver the host with modified device number needs to be resubmitted to add vehicle information thirdly if it still does not work by changing the card it will need to check whether the host s 3G 4G module fails 41 Hard Disk Mobile DVR User Manual V2 0 Appendix 3 storage space
9. V2 0 Center vehicle management software platform it can CMS manage more than 20000 devices at same time if need to manager more units add more servers to realize it Software hval Support Flash disk to upgrade the firmware Upgrade 1 4 MDVR electric Specifications to see Table 2 Table 2 MDVR Electric Specifications dems Parameters Specifications 8V 36V When long term under 8V or long term over Power input 8V 36V 36V Auto power off enter protected mode Power output 12V 0 2V Max 3A Power OFF ACC Detection Video input Impedance 75Q for each video input impedance Output 2Vp p CVBS analog signal displayer device Video output Volt 2Vp input need 750 impedance to fit it Low level alarm I O interface High level alarm Operating Temp 40 C 75 C Under well ventilated environment 1 5 Product Applications The MDVR products application connection diagram Please refer to figure 1 1 This product can be used for video surveillance or remote monitoring which applies in common or special vehicles such as buses logistic vehicles trucks long distance coaches taxis tankers cars school buses police cars patrol cars In front end it mainly collects video signal by dedicated automotive camera then transmits to the MDVR host via a special video cable to do the video compression and image processing which is locally storage in SD card It can also be remote monitored or remote video recorded and
10. can not input numbers under Chinese input state then you need to move the cursor to the in middle word press ENTER key to turn to EN and then enter numbers 95886 After the completion of above steps press the RETURN key to go back and save other text input under other menus will be more or less the same Please press CANCEL to delete it when there is a typo during the input process Figure 4 2 Figure4 3 3 3 Video settings 1 Video Start Up After the installation of a new SD card in the device the formatting is recommended after normal boot into the system in order for system to have better compatible relationship with its format After the formatting host will automatically start up the video when restart 2 Timer recording Firstly modify to be timing video under the System menu Video Settings General Settings Video mode save and return to the previous menu level to be video plan and then set the time period of the video save it after setting finished 3 Alarm recording Firstly modify to be alarm recording under the System menu Video Settings General Settings Video mode then set the alarm pre record time range 0 60s and alarm video delay 30 900s alarm output delay 55 2555 which can be set according to the actual external alarm device Secondly itis needed to install the corresponding external alarm input device such as the emergency button set by sensor power switch for open close door
11. packed to be included into alarm record range 0 30min to form an alarm recording file 7 Alarm out sec when alarm occurs the continuous output time of an alarm after connected to an external alarm device the output time 5S 2555 8 Alarm file lock time is the storage time for alarm video to be saved on the hard disk the mirror disk SD card in protected storage time the alarm recording will not be overwritten even if the SD card is full there are optional 1 3 5 7 10 15 30 45 days under the drop down menu please set the appropriate number of days according to the hard disk capacity 9 Video encrypt Video files can be encrypted using the player on a PC requires a password when playback 10 Audio output volume You can set the output volume 11 Live mode You can set the number of channels the boot screen 27 Hard Disk Mobile DVR User Manual V2 0 5 2 Main Code MATN CODE 1 Enable On means open the recording CH X Enable les Fps QUAL Audio function of this channel off means not CH 1 D1 y le OF i recording When some channels do not el need record or video recording you can switch off the channel in order to save the storage capacity of the storage device 2 Resolution optional D1 HD1 CIF 3 Frame rate PAL is with adjustable 1 25 frame full frame rate is 25 NTSC is with adjustable 1 30 frame full frame rate is 30 4 Quality optional level 1 8 level 1 is with the highest quality 1 while l
12. server generally the default is set to 6608 port 5 intercom IP port That need for an external intercom equipment input intercom IP and port the default is usually 12030 6 IC card IP port That need for an external IC card device enter the IC card IP and port 26 Hard Disk Mobile DVR User Manual V2 0 5 Record Setting 5 1 Basic Settings RECORD SETUP RECORD BASIC SETUP Bi Record Type Live Mode Nine Ch La i Record Mode Auto y ad Packet Time y NORMAL MAIN CODE SUB STREAM RECORD PLAN a PreRecord 30ming ALM Delay 115 0 30mins y ALM Out Sec 75 5 2558 MIRROR ALARM REC SPEED REC ALM File Lock 5Days Video Encrypt OFF ly AOut Volume p 1 Selectable record type common record or record I frame 2 Selectable record mode boot record alarm record timer record 3 Selectable packet time 15 30 45 60 minutes which stands for the time period how long the video file will become a packaged file 4 Automatically overwritten can be selected to on off when on the previous video files will be automatically overwritten if the hard disk space is less than 2G as well as the mirror video disk amp SD card space is less than 300M 5 Alarm pre record time when alarm occurs the recording before the alarm occurs will be packed to be included into alarm record range 0 30min 6 Alarm recording delay when alarm stops the recording after the alarm stops will be
13. td O Z HE 232 1X IDEO OU UT solo 1 12V OUT 1 12V OUT 25 gas amp 2 6ND 2 GND AACA 3 A IN 3 A IN 4CH MDVR Back signal definition diagram 4 V IN 4 V IN Table 4 Back panel interface Definition Table eres mems besepton 3G 4G Antenna Interface I O Serial AV out O amp RS485 amp R Switch input interface high level gt 4V interface 5232 AV OUT Input Vehicle speed pulse signal RS232 Digital voice intercom Insert network cable the LED will light Network Interface on when network Is connected successfully USB Interface Optional Mirror image recording storage media 6PIN Extended interface RS485 RS485 Serial Interface Printer Interface MCU ICP System debugging information interface AV IN CAM1 2 3 4 Video Audio input and 12V out 11 Hard Disk Mobile DVR User Manual V2 0 2 5 Power Cable Power cable as picture 9 one end is 6pin white plug it connect with the 6pin white plug of device back panel The red and black cables are directly connect to the vehicle s battery Red cable connect to positive black cable connect to negative Yellow cable is FIREWIRE The device will automatically start when turn on the vehicle key and close when turn off the vehicle key Yellow cable is connected to the gear that vehicle key open all the dashboard light the gear of starting vehicle motor Notes 1 Before connecting confirm the voltage
14. A wireless 3G settings Please pay attention to the supporting type of network during wireless 3G setting WCDMA EVDO and TD SCDMA Also note the access point and the center number The user name is in default in domestic which is basically not needed to modify however there is also in some domestic places he 3G card needs to be entered by user name and password and some foreign operators will needto enter user name and password as well the access point and the center number will need to be modified too which is required to input relevant information according to the local network data You can press INFO key to query whether ENABLE ENABLE LON hy ENABLE TYPE TYPE TYPE APN APN APN CENTER NUMMER CENTER NUM ETE CENTER NUMSEEES USER NAME USER NAME USER NAME PASSWORD PASSWORD EEE PASSWORD EEE IP ADDA C local IP settings Local IP setting is the setting after the RJ45 port access dept the network cable set the local IP and central server MAC ADDA Q numberto make it be linked from local area network to SERVER IP i 192 168 000 208 WAN through the network cable which can also reportto tt CONTROL PORT gServer server platform Step 6 These are networked into the way when connected to the network the next step is in the CMS management software on the PC operation the two steps If you are self built server the client account and add their own vehicles and assigned vehicles If it is mou
15. Hard Disk Mobile DVR User Manual V2 0 User Manual for GPS 3G 4G 4 8ch D1 Hard Disk Mobile Digital Video Recorder MDVR Model JH4 amp JH8 Hard Disk Mobile DVR User Manual V2 0 Catalogue la Produet SPECIFIC ATION vas 4 Ti Prodr VEN ENE 4 TE RFE FAT Side 4 1 3 MDVR detail specifications to see Table 1 occcccoonnccnccccnonconccononnnnnnnononncnnonononcnnnononancnnnonnnanrnnnonnnnncnnnnss 4 1 4 MDVR electric Specifications to see Table 2 ooonccccncccccoccnnccnnnncononononncnnnnononnonannnnnnnnnononnnnnennnnnononnnans 6 Lo Proqucr ADPICA ONS auroras dro e arlalen 6 2 APpearance OF Pr AU eee aaa uate aaa ates eaverei detente 7 2 DEVE APENES GLE 7 2 2 Device drawing Dimension amp Install Holes ccooocccccconnncccocnonoconnnnnonononcnnannncnnnnoncnnannnconannnnnnnns 8 2 3 Front amp Back Panel led Plug in MOQuIe cccccccoonccnccoccocconccononnconconnonncnnnnononnconnnonnnncnnnnonannnnnonnnnanos 9 2 4 Back Panel interface CePINItION cccccccssseeeeccceeeeceeecceeueeeeecueuseeeecesuaueeeeseueaeeeeessaaeeeeessaaeeeeesssaaass 10 SPONTAN 12 26 GPS Antenna and SE 46 MENA le 12 2 7 Alarm input and output eoserrernrnnnnnrrnnrnnnnnrennnnnnnnrrnnnnnnsnsennnnnnsnsennnnnnsnsrnnnnnnssennnnnnsnsrnnnnnnsrennnnnsnneennnnnn 12 e Device NSA 01 GUd savanne 13 3 Remote Control Function Instruction rresnnnnnnnnnvennnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn
16. N3P0 avi 3110P3N4PO0 avi rie 1014 000kmh i EEG Lipsett ice t Q Lipsett Tce E 5 m T 7 D Z S C O K 9 17 v 2 rs 5 2 S 2 w gt S p o o By Ave 2 gt 3 o 2 gt D m DI GPS 3456 2111S 13832 4189E Time 2012 10 Speed 6 10 knr Driver Position 138 5 amp James Schofield Drive SN 000km h 34 9368448 Alarm Thrifty Car Rental Adelaide Airport pep a miek SHIA Adelaide Europcar Airport Adelaide Airport 4 a GPS 3456 21115 13832Z 4189E 00 09 22 2X 2012 10 23 05 41 00 06 10 53 2012 10 23 05 50 22 00 09 22 00 29 53 KA eg le y lave Tf i om mm oka Cr l h de WN Sy h DD a ULV ES v we A AA eee e 05 44 05 45 05 46 05 47 05 48 05 49 05 50 05 51 05 52 05 53 05 54 05 4 Vehicle Status km h L L A E i L 4 L L L L i 1 L 1 1 L 1 i 4 L L 1 L L L L L L 4 L l i i L L L 1 i L L L 1 z 169 Acceleration f Sensor 127 IO 84 Event 42 0 o Figure 3 9 22 Hard Disk Mobile DVR User Manual V2 0 3 6 Fast report by vehicle server Note The following described iS invalid to the host which is without 3G module it is not needed to report to gServer platform Step 1 Install the SIM card 3G card which supports WCDMA EVDO TD C DMA detailed installation please refer to Chapter Il 2 2 and 2 7 Step 2 Enter into the system menu after starting up firstly modify the host
17. OG 3 Inserting the USB storage device to the front USB port the current configuration parameters of this device can be imported into the USB storage device to become a parameter which can be imported to use 4 The users can modify boot logo and upgrading logo according to their own needs a Logo image size 720 576pix Less than 256KB name and format loading jpg boot logo upgrading jpg upgrade logo b Copy the 2 logo images to the USB flash thumb drive directly at same time plug it into the USB2 0 port c Turn off 3G wireless module and wifi module login PERIPHERALS WIRELESS SETUP Wireless and WIFI SETUP set to OFF then press save button d Login the MDVR TOOLS CONFIGURE UPGRADE LOG Need about 2065 it will be prompted to upgrade logo success DEFAULT CONFIG IMPORT CONFIG FILE 7 2 Format FORMAT SD CARD Format HDD SSD USB SD Card lt can be chosen to format the hard disk Select HDD mirror disk SD card and USB Note the hard disk must be formatted when inserts to the device by the first time FORMAT 34 Hard Disk Mobile DVR User Manual V2 0 7 3 Log Search Calendar with green background means it has 01 02 03 07 10 11 log log query starts by selecting the date start time end time log type system log alarm log Such as on amp off video loss parameter DATE 2 setting Start Time 00 00 00 End Time Log Type I stem y SEARCH 8 Peripheral Settings o
18. and pulse getting during vehicle traveling 3 Speed unit KM MPH can be switched high speed limit threshold means the maximum speed of the speed limit if you turn on the alarm the alarm will be generated when the speed exceeds the threshold alarm information can also be transmitted to center CMSServer platform for recording 4 When selecting type to be event the record file is a normal record when selecting the type of alarm the record file type is alarm 5 Speed Alarms can be transmitted to the center CMSServer platform 6 3 G Sensor Settings G SENSOR SETUP 1 Enable on means this sensor turns on Unit g 2 Calibration is required before G Sensor Name EnablelThershold Type setting calibration is to clear X Y Z parameters G Sensor can be understood as OFF l 0 00 vant le a three dimensional X Y Z axis which OFF Il 0 00 F sij respectively stands for three groups of states upper and lower left and right front and rear uniform has no effect and the G Sensor X 0 00 Y 4 00 Z 0 00 JUDGE setting is mainly to set a threshold value which needs to be determined Generally speaking vehicle s instant acceleration is relatively large in case of slam the brakes on crash acceleration and sharp turns whose intuitive reflection is threshold beating and PC displays X Y Z three states by waveform when playing back When an alarm is generated it also can be sent to center CMSServer platform to record alarm information 3 When
19. brakes lights and other sensors the following are the several main alarm settings of this device A The sensor input alarm system system menu alarm settings sensor settings Set the menu in Figure 4 21 with high or low trigger level and then turn on the alarm this menu is corresponding with four external alarm input SENSOR IN which can be for eight external alarm output it must be connected to the corresponding external sensing switch device such as door magnet power supply emergency button turning signal switch brake lights Figure 2 12 etc rough connections are ps level input E _ _ _ _ SENSOR IM1 External sensor switch _ 19 Hard Disk Mobile DVR User Manual V2 0 B peed alarm setting system menu alarm settings speed setting If the vehicle selects the GPS to get speed information which requires normal status of the GPS signal then we need to set a high threshold speed limits such as 100km h that is the maximum speed limit alarm is opened when vehicle is started vehicle will output alarm when the vehicle speed exceeds 100KM H lf you choose to obtain speed information from the vehicle it must be connected to the speed pulse sensor which is used to calculate the speed ratio coefficient pulse speed the pulse sensor is connected to the two wires SPEED A and SPEED B of our device the speed ratio will be measured according to the set speed and pulse during vehicle s moving
20. corresponding table Appendix 3 storage space corresponding table RECORDING SPACE M H The space occupying for each image video recording per hour is shown as above table which is for reference only the actual video file size has something to do with light changes of the current channel movement of object and many other factors if the image is stationary then video file size will be much smaller in order to save space it can be set to turn off the audio or turn off the channel without video Appendix 4 MDVR Before loading the tool to check Equipment installation before the installation is required to prepare the necessary installation tools common tool types in the table below NO NAME Specification Explanation 6 Display Special For debugginghost 8 Screwdriver Onrequest Forequipmentfixed 9 Hexwrench Onrequest_ Forequipmentfined gt 42 Hard Disk Mobile DVR User Manual V2 0 Appendix 5 MDVR Before loading the installation of auxiliary examination Equipment installation before the installation to be complete some of the necessary installation accessories accessories category in the table below Self Line tapping T GN a deductio SCreWS n Flame retardan t corrugat ed pipe Insulating electrical tape 43
21. d in Hard disk which is used as the storage medium The MDVR may look simple in its exterior design provides powerful auto black box features installation flexibility and high reliability 1 2 Key Features 4 8 channel video amp audio synchronous real time recording and playback 4ch D1 25fps 6ch D1 25fps 8ch HD1 25fps 8ch CIF 25fps options PAL Built in 2 5 inch HDD SSD supports max 1TB Professional hard disk damping technology 3G 4G network such as HSUPA HSDPA WCDMA EVDO is selectable Built in GPS module Built in G sensor External WIFI special interface Built in 1 SD card for backup recording when HDD SSD errors 2 high speed USB2 0 interfaces the front is used to export record file The back is use to mirror recording for waterproof and fireproof 8 digital alarm inputs 2 digital level output 3 RS485 interfaces 1 RS232 interface Built in hard disk heating technology It can be worked in 40 C 75 C Power supply 8V 36V 1 3 MDVR detail specifications to see Table 1 Table 1 MDVR Specifications hems _ Parameters nektet English System Graphical User interface OSD menu Hard Disk Mobile DVR User Manual V2 0 PAL NTSC H 264 Main profile Video Video Signal Video Compression PAL 100fps at D1 NTSC 120fps at D1 4CH 8CH Audio input Software supports simultaneous Audio input po EE open 2 Audio Audio Audio output 2 CH Audio output Recording mode Audio amp Video sync Recording 4CH 4D1
22. ding to the communication configuration of the machine insert the SIM hi Num 994 card supporting 3G 4G User Name car WCDMA EVDO TD SCDMA Password oka FDD LTE TDD LTE SIM card slot is on the NetMode Se front panel open the lock to open the protective cover you can see the SIM interface follow the instructions to insert the SIM card correctly 2 Plug in the 3G 4G antenna after SIM card inserting ensuring that the system is able to receive good 3G 4G signal 3 Edit the image information under the 3G 4G Settings menu interface A Wireless set to open B Select the type of communication press ENTER button to select the corresponding module WCDMA EVDO TD SCDMA FDD LTE TDD LTE is determined by the type of model one model only support one mode C The access point and the centre number is generally by default which do not need to change user name and password in some provinces are not by default some can be empty which do not need to input anything while most of them can just keep the default settings If it is a foreign 3G 4G it would need the operators to provide access points and centre number to set in some abroad places it is a must to enter username and password for a normal dial up when your host can not be reported please make sure your 3G 4G settings are correct most of the foreign districts are with WCDMA equipment D Save it after completing all the settings 4 After exiting all menus press
23. downloaded by the remote client if with 3G 4G models It can real time locate the vehicle position Figure 1 1 schematic diagram is a common mode of application each function during actual use will vary with the presence of module Hard Disk Mobile DVR User Manual V2 0 e GPSSatellite Client Client Client Client wa xo GPS Arena 3G 4G Antenna gt special camera Car rear view p o Car special camera 3G 4G Base station MDVR MGMT Gateway Stream Storage Alarm Notice Upgrade Backup Server Server ing Server Server Server Server Server Server Emergency ROUTER button Talkback Mic Car dedicated monitor screen he en mad Pickup Server ti pe Figure 1 1 MDVR Schematic diagram 2 Appearance of Product 2 1 Device Appearance Hard Disk Mobile DVR User Manual V2 0 2 2 Device drawing Dimension amp Install Holes a vm En a n A 2 nr a um ATA bad a Ci Jee a m em lt m J Cl A em fen eed Lg Jr ie An b Loe jm 160 176 Mounting hole m TD 184MM ANTI TN 176 Mounting hole 184MM Hard Disk Mobile DVR User Manual V2 0 2 3 Front amp Back Panel led amp Plug in module 4ch and 8ch MDVR Front s m REC ALAM HEAT 3G K j l Fa SD 20 R pwr SD HDD GPS 4ch and 8ch MDVR Front Table 3 Front Panel definition Interface ltems Descrip
24. e Naa 37 MO System NORR 38 Appendix 1 CMSServer platform interface xxxrnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnenennnnnnnnnnnnnnennnnnnnnnnnnnnennn 39 Appendix 2 Common problems and treatment nrrrnnnnnnnnennnnnnnnnennnnnnnnnnnnnnnnnnnnnnnnnnnnnennnnnnnnnnnnnnnnnnennnnnnnnn 39 Appendix 3 storage space corresponding table rrrannxrrnannvvrnnnnnnennnnnvennnnnvennnnnnvennnnnvevnnnnvennnnnnennnnnnvennnnnr 42 Appendix 4 MDVR Before loading the tool to check rrrrrrnnnnnunnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnvnnnnnnnnnennnnnnnnr 42 Appendix 5 MDVR Before loading the installation of auxiliary examinatiOn s sxernannvernnnnnvrnnnnnvennnnnr 43 The final interpretation of the specification pictures and text interpretation all belong to the company Without notice when content is changed Hard Disk Mobile DVR User Manual V2 0 1 Product Specification 1 1 Product Overview Hard Disk Mobile DVR Automotive is a cost effective multi functional device designed for video surveillance and remote monitoring of your mobile assets It uses a high speed processor an embedded Linux platform and the most advanced technology in the IT field such as H 264 Video Compression Decompression 3G 4G network transmission technology and GPS positioning technologies MDVR can realize four eight channel video recording Each channel supports CIF HD1 and D1 image solution Drivers driving information GPS data and alarm data are recorde
25. enerally connected to the circuit of car such as door open close button brake lights turn signals etc they are in effective when sensor input is high level users generally use higher than 4V high level to trigger alarm Note less than 4V is low level 4 When selecting type to be event the record file is a normal record when selecting the type of alarm the record file type is alarm 5 When an alarm is generated it also can be sent to center CMSServer platform to record alarm information 6 Out delay When setting the alarm output on interface menu the of alarm linkage the alarm is triggered off when the alarm output is set long delay 7 O Alarms can be transmitted to the center CMSServer platform 6 2 Speed Settings 1 There are two options of Speed Source Source GPS and vehicle if selecting the GPS the coefficient X100 0 speed of the vehicle can only be sent to the Unit KMH device when the device has the GPS module Name Enable Threshold Type and GPS signal the vehicle can get the L SPD OFF WW 5 rent vehicle speed information by GPS H SPD OFF 120 ent le 2 If selecting the vehicle to get the speed you need to connect to the pulse sensor to calculate the speed ratio coefficient pulse speed 100 the pulse sensor connects to the device port SPEED A and SPEED B two lines and the speed ratio is measured 31 Hard Disk Mobile DVR User Manual V2 0 according to the set speed
26. eo recording time period 3 Check the SD card inserting status and whether the SD light on front panel is on or not Q The video file is missing or there is no video file within a certain period of time how to do A 1 Determine the time period by analyzing the final video file before missing and the first video file after recovery 2 Confirm whether the host is not on during that period of time such as when the driver halfway parking loading and unloading goods while the host is not set by video delay Q When car PTZ cannot be controlled it cannot rotate up and down how to do A Check whether PTZ protocols and baud rate are set correct address codes are corresponding or not whether have selected to maximize the video of the channel when control the PTZ for example when control the second channel it must maximize the screen of the second channel image to control it GPS related issues Q GPS module exists but no coordinate information A 1 Check whether GPS module exists if it does not exist check whether the hardware is installed or in a good contact 2 Make sure that the GPS antenna contacts are good whether the antenna is broken it is recommended to be located in places with strong signal note that some car glass shielding film will block GPS signals 3 If the test is in the room the signal of GPS antenna in the room will be obscured it is recommended that the GPS antenna is placed outdoor Q Deviation of GPS location on map
27. er setting use for select digit During playback and preview 1 2 3 4 is for the switch of the channels key adjust digit when plus or deduct or delete ENTER key under setting means select and save On playback condition press ENTER can reveal parameters in OSD OVERLAY menu when it s ON on screen 17 Hard Disk Mobile DVR User Manual V2 0 Table 6 Function keys on remote control Startup power off Through screen press this button twice for reboot soft start key ans note can t be use now LOGIN When setting password press LOGIN input password Do please remember password due to device have no reset function INFO Check info Press it Switch between 1 channel 2 channel 3 channel 4 channel a 8 channel version Press digit key 1 2 3 4 5 6 7 8 can separately switch to CH1 CH2 CH3 CH4 CH5 CH6 CH7 CH8 Digit keys1 2 3 4 5 6 7 8 RETURN Return to upgrade exit setup menu and return to screen PAUSE STEP When playback recording press STEP a time play a step press PAUSE it stop Press play key then normally play GOTO When play back press it can jump to designated time and play FRAME Press FRAME key then FRAME play PLAY key when PAUSE it will show still image a Stop manual PTZ or recording key Start manual recording key NEXT Turn to next page next file when playing PREV Turn to previous page previous file when playing PRESET ZOOM FOCU S IRIS PTZ PRESE PTZ func
28. evel 8 with the lowest quality the quality setting good or bad has a direct impact on the effect of record playback Under the same resolution the higher the quality the clearer the record The record file will obviously take up a relatively large space 5 Audio audio channel can be set on or off if on there is sound from the corresponding channel during record playback maximum two channel audio can be opened Note The main code plus mirroring video can support 6 full frame D1 record 5 3 Sub stream SUB STREAM SETUP Description sub stream is important Res Fps Mode Prate parameters when video and data are JU 156 fy uploaded to the network through 3G 4G and its settings are related to the clear and smooth watching effect of video on CMS platform of course network transmission mostly depends on the uplink and downlink rate of local network 1 Video resolution can be set to be CIF or QCIF 2 Selectable frame rate 1 25 PAL 1 30 NTSC 3 The bit rate can be set to dynamic bit rate VBR or constant bit rate CBR optional 16 384kbit s 4 Default setting is bit rate 96 frame rate 10 But this can be set according to your own network If the network bandwidth is good enough then the frame rate and bit rate can be set higher 28 Hard Disk Mobile DVR User Manual V2 0 5 4 Recording schedule 24 hour 1 If the timer recording mode is selected in Period basic setting it is needed to set a regula
29. evice must connect external relay Shown below is the Alarm output photoelectric alarm wiring diagram MDVR alarm output 2 8 Device Installation Guide A Inspecting the Accessories After unpacking please check the device for damage or deformation If there are please do not install the device and get in touch with the supplier In the product box there is a packing list Please cross check this list with the device and its accompanying accessories Table 5 Packing List Hard Disk Mobile DVR JH4 Packing List Specticatons unt a esses Gor reef Power Line 6PIN 6PIN Big557 L 200mm pos 1 Remote Control wh HDD SSD Case fs ft Connecting Line 4PIN Air connector convert aw ee RCA BNC DC L 200mm pes demand Electronic Key eha Desiccant fps pt Pearl Cotton ESE GPS Antenna 3503 L 5m 13 Hard Disk Mobile DVR User Manual V2 0 3G 4G Antenna 3G 4G Antenna Protectivecover ps ass US made screws 8 AC 8 9MM eve 4Pin Port Convert BNC Composite video Cable 8CH wiring A is the first CAM B is the second B HDD SSD SIM card SD card installation Unlock by the key insert the HDD SSD into the HDD SSD slot in front of the mainframe Notice if draw out The HDD SSD the front part of HDD SSD should has a space of over 10cm the length of HDD SSD 14 Hard Disk Mobile DVR User Manual V2 0
30. high quality video parameters 1 Corresponding record On means the corresponding alarm recording function is on 2 Optional resolution D1 HD1 CIF 3 Frame rate PAL with frame 1 25 NTSC with frame 1 30 5 Audio this can be set whether to open the audio of the record if on then the audio will be recorded into the record file 5 8 Speed Record Optional SPEED REC CH X Enable E E Threshold 10 km h CH 2 ICH 3 CH 30 1 Set the speed threshold of recording 2 Set the four channel record enabled on means open the record while off means close the record 3 When the speed exceeds the speed threshold the channel will not record with enable off only channel with enable on will record Hard Disk Mobile DVR User Manual V2 0 6 Alarm settings E y IO Link To CH t T Name O ax 8 char G SENSOR Enable IF E Level High be Type Alarm gt 4 OutDelay 20s TEMPERATURE MOTION DETECTION jor setting 6 1 Sensor Settings 1 IO amp Name Users name the custom sensor according to the lO interface when install MDVR for example to change the name IO1 to be Chinese front door brake etc you can press the ENTER key and then input under the soft keyboard state 2 Link to When an alarm is triggered the monitor screen automatically pop up enlarged channel selected channel 3 Enable on means this sensor turns on the device supports up to 8 sensor inputs these alarm input is g
31. ill use diagonal set please refer to Figure 4 30 As long as you set the motion detection area and set the video mode as alarm recording the image move will trigger the video to generate alarm recording files Note it can only take effect after setting and saving 3 4 PTZ connection way and setting Setup steps Firstly select the PTZ protocol divided into PELCO D and PELCO P protocol most of peoplewill choose PELCO D Secondly set the baud rate there are four options 1200 2400 4800 9600 which must be corresponded with the baud rate on PTZ Thirdly setthe address code directly input the address value corresponding with PTZ setting corresponding is required Generally the defaulted PTZ address code is 1 PTZ address code has adjustable DIP it is needed to set different address codes to identify when there is many PTZs Fourthly wiring Connect control wire 485 on the PTZ to the RS485 A positive pole connect the other one to 4 The power input of the PTZ Figure 4 6 selecting the channel access to PTZ for example if PTZ connects through channel 2 then T After wiring and parameters setting of PTZ users can only use remote to control PTZ after Note you need to switch to channel 2 maximize on the monitor interface to control it 20 Hard Disk Mobile DVR User Manual V2 0 Second way with a three dimensional keyboard control PTZ IN RS485 A CON Connection Key iT
32. ime proofreading DATETTME Data Type DATE 2014 04 01 TUE Time Format I Hours le Time 15 59 Time Zone MT 08 00 w 00 DST Switch OFF and manual time proofreading when select GPS time proofreading the modified time will OPR Timeout 5 min 7 change because of reaching the GPS time Timing Mode GPS proofreading point so if you want to modify Timing Time 12 00 0 the time it is suggested to choose manual Power Mode Leni time proofreading mode which can be in normal after modifying time Way of modifying the time and date move the cursor to the number which needs modification and directly press the corresponding number keys on the remote control press the save button after set 3 Operating timeout three options 1 minute 5 minutes 15 minutes for choosing to set how many minutes later will automatically exit the menu after entering the menu General settings menu interface 4 When the GPS time proofreading opens in the default time zone such as the default GM 08 00 time zone system will automatically proofread time by GPS when it reaches time proofreading point 5 Power mode the ignition mode timer mode the ignition mode is that MDVR began to start up after vehicle starts its key this operation is recommended as the preferred default starting up timer mode is the operating mode of startup and shutdown at the point of time set by the user 6 Power Off delay In the ignition mode as long as the wiring is cor
33. is between 8V 36V or else if over this range the device will be fired 2 After connecting the cables Ensure that power cables are insulated to prevent short circuiting and burning out the battery 3 The Yellow cable must be connected to the vehicle ignition cable otherwise the device will not be able to execute the delayed shutdown and the final moment of the video will be lost 4 Note Connection to the vehicle s engine must be connected directly to the positive anode of the battery Do Not Use bond strap for grounding as it will produce negative pulses that would interfere the device s normal operation The negative pole of the power code must be 1 5mm and above 4G 2 6 GPS Antenna and 3G 4G Antenna 2 Alarm input and output The device has 8 alarm input and 2 alarm output interfaces Alarm input detection is level detection 12 Hard Disk Mobile DVR User Manual V2 0 Various state of alarm level can be detected while the vehicle is in motion such as braking steering horn etc Below is a diagram that shows when the braking vane Is depressed the MDVR would be able to detect the high level otherwise just detect the low level Yellow line ACC Carcircuit k Black line control a Red line AAA Only used as atest wiring Mo v DC12V 5A More Connection diagram 2V 55AH Car battery Figure4 1 Alarm outputs are level output drive capability for the 200MA if you want to drive relatively large power d
34. isplay GPS module WIFI module 3G wireless module and SIM card intercom state IO state IMEI information the device status information is often used when checking the system status and fault judgment When it needs 3G 4G to report CMSServer platform the 3G 4G card signal and dial up state are visually displayed here and the success failure status of connecting to the server center can be also displayed The next page of System Information can view the hard disk the mirror disk SD card total capacity used space free space state IC card state Vehicle mileage You must use admin account to login MDVR when you want to reset the vehicle mileage 38 Hard Disk Mobile DVR User Manual V2 0 Appendix 1 CMSServer platform interface setting VE H i CL E er list Polling Arig UR GO erre iw pl ie e Mx t it banal tt Hp SELECTION j gt SS map CONTROL vo ERR i gt BYEN VIDEO DISPLAY VEHICLE INFORMATION AREA STATUS Appendix 2 Common problems and treatment Q What can do when found a problem with the product but can t solve it by myself A Take note of the model and software version number then submit a detailed description of the problem to the Technical supporting engineers to analyze the more detailed you have submitted the more convenient for us to analyze Q How about when there is no video output from the vehicle host device A 1 Check the h
35. kground means it has video file video search starts by selecting the date start time end time record path hard drive mirror SD card record type conventional recording alarm recording all recording channels all channels 1 4 1 8 After searching select it and click remote play button for record playback pressing the number keys 1 8 on the remote control can switch to the single channel full screen playback supporting 2X 4X 8X 16X speed fast forward and rewind Hard Disk Mobile DVR User Manual V2 0 10 System Info View the device status from system information SYSTEM INFO SW Ver T14040101 MCU Ver V403193 HW Ver JH4 M V001 GPS M VALID GPS sign N22 33 390966 E113 56 229101 SYSTEM TNFO Storage Total Used Free State HDD 488 36 92 1G 296 2G NORMAL Speed Okm h Speed Plus 0 HDD Temp 34 SIM Card EXIST SIM sign 10 SGM EXIST 3G State OK WIFI M NONE WIFI sign Center L LINK SUCCESSED INTERCOM NONE INTERCOM L NO LINK o A EE Serial Num00 00 00 00 00 00 0c 8d IME I NE dl RETURN MIRROR 0 OG O OM O OM NONE SD 8 OG 0 3M 8 0G NORMAL C EXIST NONE IC CONN NO LINK Vehicle Mileage 0 00 KM RESET PREV At the scene to monitor the status of the four screens pressing the INFO button on the remote control can directly display system information device status information includes the hardware and software version number and the MCU version information meanwhile d
36. l V2 0 1 Enable on means this sensor turns on 2 The sensitivity can be set L low M medium H high the higher the easier to detect environmental change 3 Detection area using two points of the diagonal to determine the detection area select the first point press ENTER on remote and then use the up down left and right arrow keys on remote to select another point of the diagonal press enter key again within selected area can cancel this area selecting 4 Alarms can be transmitted to the center CMSServer platform Note Motion detection can generate an alarm based on any change of the environment including brightness color etc It is not recommended to use this alarm function in ordinary circumstances 1 Select the output output selectable output output 1 output 2 in the corresponding column after selecting the output when an alarm is generated the corresponding alarm output line will generate 12V high level to drive the work of other equipment 2 It can also be chosen whether to record the Wlog Wdata on means recording off means not recording Hard Disk Mobile DVR User Manual V2 0 7 TOOLS 7 1 Parameter configuration CONF I GURAT I ON 1 When the device parameters are in confusion equipment can restore the default configuration to go back to factory settings 2 Inserting USB storage device to the front USB port the USB configuration files can be imported into this device UPGRADE L
37. most basic judgment is to replace the SIM card If the dial up failed with signal then check whether the settings of center number and the port are correct Moreover check whether the device number of the product is already occupied Q 3G 4G signal is intermittent video is jammed A At present the signal coverage of WCDMA EVDO TD SCDMA FDD LTE TDD LTE is rather wide 40 Hard Disk Mobile DVR User Manual V2 0 however there are some mountainous districts without signal coverage and some suburban areas have weak signal due to the local network constraints then it will be jammed during watching of video or video cannot be watched at all the greatest impact of this situation is from the local network Moreover check whether the frame rate setting of sub stream Is too high because the video may also occur such situation when the network is poor and frame rate setting Is high Q Why the vehicle and video cannot be seen in CMSServer client when the device has been started A At first make sure the central registration server is switched on and on the net then check whether the host device number has been occupied to cause conflict secondly check whether the settings of server centric IP and port are correct devices report to the center via the built in 3G 4G module or via WIFI If via built in 3G 4G please check whether selected the correct type of built in 3G 4G module for example WCDMA and EVDO module needs the support from corresponding
38. nnnnnnnn 17 Sn Remote CONTO eee 17 3 2 TE Near dvs 19 3 9 VISO SF seman inne 19 3 4 PTZ connection way and SettidgQ ooocccnccccccncnnnccnnancnnnnnnnanennnonnnanronnnonnnnrnnnnonnnnrnnnnnnnnnrnnnnonnnnrnnnnnnnns 20 35 PO playback Of Ihe VIGO ME are 21 3 6 Fast report Dy VENTE SEN 23 An General SENGS He 24 A e TI A ATE A EAA A T TE 24 422 Vehicle SENG vek ba 25 4 3 User management Settings ccccccoonnconcccnnoncnnnncnnnnnnnnnonnncnnnnnnnnnnnnnnnnnnncnnnnrnnnnnnnnrnnnnnnnnnrnnnnnnnnnnnnnnens 26 AA NEMWOK SES seere 26 5 RECOFd SEIN iia di 27 Do BASIC SEN O 27 SAESP E eaa aeee eaen 28 S STEN 28 5 4 Recording schedule 24 NOUS ccccssssccccccssseeccccceeseeeecceaueeeeeceeaseeeeecseaaseeeeseeaaeeeeesseageeeeessaaeeeesessaaass 29 55 MIROMReECOrd OPNA vesical eee 29 SO SD Reduser 29 5 7 Alarm Record Not support temporarily oocccccooccnccccononccnnnconononcnnconononcononcnnonnannnnnnanrnnnnnnrnnnnnanennss 30 5 08 SPECT Record Opina iii 30 0 Alarm Se UNS ui dida 31 A A 31 Hard Disk Mobile DVR User Manual V2 0 62 Speed Sens usara a a 31 09 G SENSORS CUNO EE RE Ne haces A E AT AE 32 64 Jemen 32 6 5 MOTOR BEEN Haare Due 33 B26 EIN KAGE SAUE Hasene 33 E TOO Sn a A A 34 7 1 Parameter COMMOULAU ON anna diia 34 A FO ANT 34 TE SAT 35 Bi Peripheral Senna 35 VA A 35 8 2 JG 46 SENGS svar 36 9 WIFI SENOS eee eee eee ener ee eer eee ee eer feed een eee ee eer nee eee eee 36 BA OMS STINGS A A Po 37 9 Record S
39. nt server manufacturers assisted by technical staff added Ultimately reported to the CMS CMS detailed operation please refer to the relevant technical documentation 23 Hard Disk Mobile DVR User Manual V2 0 VEHICLE INFO USER SETUP GENERAL NETWORK E NORAL CODING SETUP SUB STREAM jr REGORDPLAN MIRROR SD REC LOGIN ALARMREC SPEED REC SENSOR RECORD ALARM G SENSOR TEMPERATURE MOTION DETECTION LINKAGE TOOLS CONFIGURE FORMAT SEARCH LOG PTZ SETUP PERIPHERALS WIRELESS SETUP WIFI SETUP Default password 888888 SYSTEM IN FO 4 General settings SETUP MENU BASTC SETUP eee RECORD DATES TIME VEHICLE INFO USER SETUP I gt 50 3 PER PHERALS SEARCH SYSTEM INFO DISPLAY Time vehicle user network display setup asic of the device General settings is the first menu in system menu the generic setting interface contains four function options date and time vehicle information user management and network 4 1 Date amp Time Set the system time and some other basic properties of the device 1 Date Format Press ENTER drop down menu to use the arrow keys to select the output format of 24 Hard Disk Mobile DVR User Manual V2 0 date year month day day month year and month day year 2 The date and time settings two ways for time proofreading GPS t
40. nual V2 0 4 Mile Accrual Setup ON mileage statistics and upload CMS client 4 3 User management settings SECURITY SETUP Password Enable ADD MODIFY DELETE 4 4 Network Settings Network setup interface NETWORK SETUP P Addr l Netmask Gateway MAC Addr Net Mode Server Addr Control Port Intercom IP 192 14 Intercom Port 1111 eCard IP cCGard Port 1 Password effective settings to select on or off 2 Only administrators have permission to modify the passwords of users and administrators Ordinary user s password is initially set as 000000 and the initial password for administrator is 111111 When password change finishes and exit menu it will need to use new password to log in again 1 IP address Mask Gateway etc are LAN network setting after plugging in the network cable there is no need to input if you do not use them 2 Net Mode IP Server use Static external network IP DoMain Server use Dynamic Domain Name Server You need to input your Domain Name and DNS IP when you select Domain mode 3 Server s IP address is the one MDVR host using 3G 4G to report to CMSServer platform central server which generally is the public fixed IP the IP address must be set up or else 3G 4G host cannot report to platform this requires our host can support 3G 4G this menu will no need of setting if the host is without 3G 4G module 4 Control port set to be the port number of the gateway
41. ost s turn on status if only a blue light on it means the host is in standby status and has not been started up yet meanwhile check whether the host s power cords red amp yellow cords are in power supply status or not if only one cord is supplying power the device is unable to start up 2 Check the power supply status of display screen as well as check whether the display video has been switched to AV status 3 Check the connecting status between the host s video output cable and display screen 4 check whether the lock status of the host s LOCK it must be locked before normal starting up Q How to do when the car host video input interface is different from the camera output interface A The car uses 4PIN type while camera uses BNC or aviation head type if not in correspondence please use conversion head for connection or wiring based on standard corresponding according to the cable sequence defined by the car host Q How to do when the device does not conduct video recording after it is turned on and SD card has already been installed A 1 Check whether the SD card has been formatted or not after installation because unformatted SD card cannot be used Enter System Menu System Tools Device Format to format the newly installed SD card 2 Check to see whether video channel is closed or not whether set a timer recording or not it will not 39 Hard Disk Mobile DVR User Manual V2 0 take video when it is not within the vid
42. r Everyday 00 00 OG time period Two time periods can be kile QO chosen Move the cursor to the desired luesday Woi time period then input by pressing the Thursday 00 number keys on the remote control Timer Friday 00 00 00 recording mode is not commonly used Saturday 00 00 Ae customers can use it according to actual Sunday 100 00 situation Most customers chose to boot recording and alarm recording Wednesday 00 5 5 Mirror Record Optional Description Mirror record is used as a record backup to prevent record missing issue caused by hard disk error the parameter setting can refer to the main code parameter settings CH X Enable eg Fos QUAL Audio CH1 CH2 ON e 4 cH3 ON N CIF 5k 6 CH4 ON Id FR 5 6 SD Record Description when the hard disk does not exist due to vibration or other reasons the record Rec backup files will be stored onto SD card if you turn on the SD record function 29 5 7 Alarm Record Not support temporarily ALARM RECORD ASource Record IN HDDBTp ON IN 4 Motion N pigi Al Speed IN ID Sj 4 Adjustable video quality 1 8 1 is best Hard Disk Mobile DVR User Manual V2 0 Description Under normal circumstances for example you can set the resolution of the main code to be HD1 or CIF frame rate set to be 10 the quality set to be 4 when alarm triggers recording alarm recording can start in accordance with the set
43. r after the completion of the shortcut icons displayed on the desktop Installation steps are shown in Figure 3 7 Welcome to the MDVRPlayer Completing the MDVRPlayer Setup Wizard i Setup Wizard This will install MDVRPlayer_WIN_6 3 3 2_20140331 on your computer Setup has finished installing MDVRPlayer on your computer The application may be launched by selecting the installed icons It is recommended that you close all other applications before continuing Click Finish to exit Setup Click Next to continue or Cancel to exit Setup MDVRPlayer WI M 6 3 3 2 20140 331l exe Figure 3 7 21 Hard Disk Mobile DVR User Manual V2 0 A LS gt s User 7 Password Account admin password 000000 Connect Hard disk to the computer s USB port the computer automatically recognizes the newly installed hard drives video files are stored in the form of the date folder open the folder and display video files video files named suffix avi Figure 3 8 play the file screen shown in Figure 3 9 eye ene TE A A A 2 AT 2 Pia A la 2 ILE L4 13 KON KON KON KON xa xa xa xx lleb rte Jslyzkd W20130202 10 W20130202 10 W20130202 10 W20130202 10 sete E hs 1610P3N1P0 avi 1610P3N2P0 avi 1610P3N3P0 avi 1610P3N4P0 avi SE ng gg Re Mordackup A eL fil RON KON KON KON TE EE In a Figure 3 8 W20130202 10 W20130202 10 W20130202 10 W20130202 10 3110P3N1P0 avi 3110P3N2P0 avi 3110P3
44. rect you can set the delay off of host delay off time range is from 5 minutes to 1440 minutes MDVR will continue to do the video recording by the delay off set time before shutting down when the vehicle is turned off 7 Auto Maintenance function when the MDVR work more than 24hours setup ON give it a time MDVR will automatically restart to work properly this need about 50 seconds Power Off Delay 5 5 1440mins MAINTENANCE ON v TIME 02 00 00 SAVE 4 2 Vehicle settings VEHICLE INFO 1 Device Num user sets a unique device Serial Num 00 00 00 00 00 00 03 ee number to each device which will Dev Num 30004 automatically display on the right of the Company Name number input box The device number is 6 Vehicle Num 00001 digits amp characters digits are effective If it is Driver Name TOM 3G 4G device it is strongly suggested to set gt IM Num a unique device number because a server a requires only one device number 2 Vehicle identification number this number is recommended to be set during installation because the vehicle identification number will be superimposed onto the video during video encoding to be strong video evidence lf you do not enter the vehicle identification number then it will show 00000 in default For detailed input method please refer to Chapter 3 2 Text Input 3 Company name the name of the driver SIM number can fill out as demand SAVE 25 Hard Disk Mobile DVR User Ma
45. selecting type to be event the record file is a normal record when selecting the type of alarm the record file type is alarm 4 Shocking Alarms can be transmitted to the center CMSServer platform r i O 00 SAVE 6 4 Temperature alarm 1 Two temperature degree units Celsius C and Fahrenheit F 2 Enable on means this sensor turns on 3 Temperature is sent back to the device by a temperature sensor s long as you set high H Temp OFF Alarm or low temperature alarm threshold and turn on enable when the temperature is above or below the threshold the device generates an alarm which can also be transmitted to center of CMSServer platform to record alarm information 4 When selecting type to be event the record file is a normal record when selecting TEMPERATURE SETUP Ufa Name EnablelThershold vi L Temp OFF 32 the type of alarm the record file type is alarm 5 Temperature Alarms can be transmitted to the center CMSServer platform 6 5 Motion Detection MOT TON DETECT TON X Enable Sensitivity Area SETUP ISETUP ISETUP ISETUP 6 6 Linkage Settings LINKAGE SETUP ASource Output WLog Wmdata tput 1 v ON HDDBTp IE PU I y ON O Speed e sensor It pul e ON Motion Helbig ON tput 1 y ON y y y 0 Videoloss I pul ION NEXT A V 33 Hard Disk Mobile DVR User Manua
46. the INFO button on the remote control it is able to see 3G 4G communication if signal is good it will show dial up is successful the device can be reported to CMSServer platform with three points of the server IP address settings port settings and device number settings 8 3 WIFI Settings 1 Select WIFI module to be internal or external 36 WIFI Mode Enable OFF WIFI HotSpotl IntSSI I SSID Ints IP Addr NE 6 251 Netmask 1255 255 000 Gateway 119 68 000 001 Encrypt OF Auth Mode OPEN Encrypt Type NONI Password Ple e ode la 9 ID ENABLE COEF 9 Record Search 01 02 03 04 050607 08 09 10 11 re befrafisehrhehisfeoferfe ro feafesfaefor fef2sfaofer DATE 2 Start Time 00 Rec Path HDD Rec Type Auto Cl l Al End Time 23 SEARCH 37 Hard Disk Mobile DVR User Manual V2 0 2 Select enable to be on 3 Internal WIFI Hot switch can support multiple connections Please refer to the router parameters External WIFI Input the IP address of AP WiFi note the device to determine whether the RJ45 interface and external module is connected by IP Input AP WIFI s SSID note the server to determine whether to use the WIFI connection by this SSID Need to connect a special oil sensor the sensor that MDVR must be able to identify the protocol oil sensor ID Select the oil sensor type Enable ON Tank corresponding scale Per oil Oil alarm Value Calendar with green bac
47. tion AV OUT Video Audio and 12V out analog output REG i sSCSY Recording LED light on when recording ALM Alarm LED light on when device work abnormally HEAT Light on when heated 3G 4G Light on when 3G 4G module exist PWR Power LED light on when power work normally Light on if SD card exist light on if HDD exist flash when recording GPS GPS signal LED light on when GPS module exist flash if signal exist GPS IR receiver IR Receive remote control signal Hard Disk Mobile DVR User Manual V2 0 When device is working unlock the E key system will power off lock the E key system ee will work normally USB Port USB 2 0 Upgrade and Export video data 2 4 Back Panel interface definition E y 36 4G PS E 3 HE E e RN POWER VOARSANNANSJ32 RJAS USR 2 0 RSJ408SMOU CAMA AV OUT ORS oes CE ce q CAM1 RyJab USB 2 0 R8485 4CH MDVR Back Gr cere A RJ45 USB2 0 RS485MCU CAMS Gene mG ce Fe oe CAM5 amp CAM6 CAM1 amp CAM2 HO oO 0 Bao oO ol cy H CAM7 amp CAMA CE POWER seie RJ45 USB2 0 yer MCU CAMB pg AV OUT 8CH MDVR Back 10 Hard Disk Mobile DVR User Manual V2 0 CAM3 CAM1 1 12V OUT 1 12V OUT 2 GND 2 GND 3 A N 3 A IN 4 V IN 4 V IN RJ45 USB2 0 RS485 MCU POWER O amp RS485 amp RS232 AV O CAM4 CAM2 a A a CII a QI OJO z lt EN
48. tion keys T RECALL BRUSH AUTO F1 F2 F3 F1 is shortcut key F2 F3 are Spare keys Reserved for future 18 Hard Disk Mobile DVR User Manual V2 0 3 2 Text Input Need to use input method when input text such as the company name license plate number driver s name line number and other text input needs when requires input method under other menu Take inputting Yue B958s86 for example after entered the input interface to illustrate the input steps Step One in the state of Chinese input as shown in Figure 4 2 Character YUE GuangDong sPinyinis YUE move the cursor to press ENTER key to input the first Chinese letter y it will display the corresponding PinYin combination 1 5 if there is no PinYin as YUE please press the FWD key on the remote control to the next pages when it shows 1 you 2 yu 3 yuan 4 yue 5 yun on the next page please press the number 4 on the remote control which will show 1 5pcs of Chinese characters if there is no YUE character please use FWD button to tum the pages when it shows 1 read 2 key 3 Yue 4 Guangdong Yue please press 4 to input the first Chinese character YUE GuangDong Step Two Now you will need to input the letter B move net S cursor to pressENTER key to switch the input method to the state of capital letters as Figure 4 3 then move the cursor onto the letter B to press ENTER key to input it Step Three Next you will need to enter numbers press it again to switch to Chinese input state you
Download Pdf Manuals
Related Search