USER MANUAL
Contents
1. A FAQLIST B SCENARIO APPLICATION SAMPLES VoIP ATA with router function User Manual 38 39 40 eerrerr R 41 41 41 42 42 42 43 43 44 44 44 46 47 E E E E E LR 48 48 a E E E E RE TT 49 r E E E E ETTE 50 50 51 VoIP ATA with router function User Manual COPYRIGHT amp TRADEMARKS We reserve the right to change the product specification without notification Slevel is a registered trademark of 8level No part of the manual may be reproduced translated or processed in any other form without permission from 8level NEXT LEVEL IN NETWORKING All rights reserved Copyright 2011 8level SAFETY NOTICE Do not use this product near water Using the product during a thunderstorm should be avoided Do not place heavy objects on the casing RECYCLING NOTICE The symbol of the crossed out wheeled bin on this product means that it is forbidden to place the equipment waste together with other waste under penalty of fine Detailed information about recycling of the product can be obtained at local authorities local waste treatment plants aa or local distributors Forwarding the equipment waste to recycling or recovery points helps to avoid the negative influence of the harmful components present in the equipment on the environment and human health in this scope the2. primary role is played by each household VoIP ATA with router function User Manual 8level NEXT LEVEL OF NETWORKING DECLARATION OF CONFORMITY For the following equipment Product Description VoIP ATA Router Model No IPG 200 Trademark 8level We declare under our own responsibility that the above products satisfy all the technical regulations applicable to the product within the scope of Council Directives EMC 2004 108 EC LVD 2006 95 EC The above product is in conformity with the following standards or other normative documents EN55022 1998 A1 2000 A2 2003 EN61000 3 2 2000 EN61000 3 3 1995 A1 2001 EN55024 1998 A1 2000 A2 2003 Person is responsible for marking this declaration Mees C 20 02 2012 HNA it VA If i i SUNNYLINE COMPUTER PRODUCTS POLAND SP 270 0 ul Graniczna 588 82 081 Pree mierowo POLAND VoIP ATA with router function User Manual Introduce IPG 200 IPG 110 series are the low cost VoIP Solutions This document describes the usage of IPG 200 IPG 110 Analogue Telephone Adapter 1 1 Overview An Analogue Telephone Adapter or IPG 200 IPG 110 is a device that allows one to connect a normal PSTN telephone to the Internet in order to make or place telephone calls m IPG 200 IPG 110 provides a direct analog interface for PSTN PBX fax machines analog telephones and other devices that require an analog port 1 2 Audience This do
3. 200 IPG 110 has already registered to your proxy and then you can make a call 2 4 Wizard Setup Wizard for Quick Setup TA20 IPG 110 after finishing the authentication the Main menu will display 2 parts of configuration please click Connection wizard to enter quick start 13 VoIP ATA with router function User Manual Step 1 Connection wizard G8 level Welcome to the Wizard Setup CONNECTION WiiZARD The connection wizard will walk you through the most common configuration options This wizard has been broken down into two steps each of which may hawe multiple pages SETUP The woip wizard will walk you through the most common configuration options Step 2 Welcome to the VOIP ATA Connection Wizard Welcome to the Connection Wizard This wizard will take wou through the Follbowrnmg steps Step 2 System Time Setup Step 2 WAN Interface Setup Step 3 Time Zone Setup a fas Time Zone Setting Tou can maintain the system time by synchronizing with a public time server ower the Internet Enable NTP client update CSGhMT 01 00 Sarajevo Skopje Sofija Warsaw Zagreb 192 5 41 41 North America Time Zone Select Choose your time zone NTP Server Select NTP server 14 VoIP ATA with router function User Manual Step 4 WAN Port Type Setup For most users Internet access is the primary application The IPG 110 IPG 200 support the WA
4. DNS address setting As the router will assign the DNS settings to the DHCP client enabled PC 4 What is the maximum number of IP addresses that the DHCP server of the gateway can assign to local PCs A The built in DHCP server can support 253 IP addresses for local network usage 5 Why can call out by IPG 200 IPG 110 A Please check your IPG 200 IPG 110 is registered SIP Proxy Server ITSP and chink your Internet works fine IPG 200 IPG 110 can t make a call without Internet or SIP Account that from ITSP supply You must have a SIP account or know the other ATA Gateway IP Domain Name than you can make a VolP call 6 can t use web Interface to setting IPG 200 IPG 110 How can do A Please check your PC connects the IPG 200 IPG 110 Lan port or PC and IPG 200 IPG 110 with the same Subnet If you PC aren t at the same Subnet you can t Login the IPG 110 Web interface Else you let your IPG 200 IPG 110 on Public Internet Public IP address 7 Why does the one way talk happen A Generally one way talk happen when use the different codec between VoIP devices make call Please check and setting the same codec most one way talk will be solved 8 Why can call out when the IPG 200 IPG 110 under the NAT A Most VoIP products have problem in NAT Pass through By SIP there are many NAT Pass through Function can solve 80 NAT Problem You can choose STUN Outbound Proxy Symmetric RTP to Pass through NAT you don t set
5. bps G 726 40K bps Qos The QOS Quality Of Service is to guarantee that the SIP and RTP should be transmitting at the same time and Data couldn t influence the Voice quality The QOS Quality Of Service is to guarantee that the Voice and Data should be transmitting at the same time and Data couldn t influence the Voice quality When TOS bits is enabled it will guarantee the Voice have the first priority pass through the TOS enable devices TOS SIP TOS Priority Setting 184 1 255 RTP TOS Priority Setting 184 1 255 VLAN Taging Use VOICE VLAN Tags Enable Voice VLAN ID 054090 Priority 0 7 Use DATA VLAN Tags Enable Data VLAN ID 0 4090 Priority 0 7 Rese 31 VoIP ATA with router function User Manual VLAN Taging VLAN Setting You can set the VLAN setting in this page There are two parts in this page First one is to set the packets related to the IPG 110 and the second one is if you use the VLAN setting in the NAT Mode There are two kind of destination packets will come from the IPG 110 s WAN port one kind of packets will go to the IPG 110 the other will go through the LAN port to the PC VLAN Packets if you enable the first VLAN Packets and set the VID User Priority then all the incoming packets will be check with the IP Address and the VID Voice Vlan ID You can follow your service provider to set your Voice Vlan ID Data Vlan ID You can follow your service provider to set your Data Vlan I
6. can setup the DND setting to keep the device silence You can choose Always or Enable or Disable DND Always All incoming call will be blocked until disable this feature DND Enable Select Enable and the IPG 200 IPG 110 will be blocked during the time period If the From time is large than the To time the Block time will from 00 00 to 23 59 When you finished the setting please click the Submit button If there is nothing need to change please click the Save Change Item in the left side then click the Save button The change you made will save into the system and the system will Reboot automatically Block Anonymous Call Select to enable the option 30 VoIP ATA with router function User Manual Codec Setting se os sole I ee G711 ulaw E E E E E E E G711 alaw E w E E E E E E G729 E E E E E E E G723 E E E E E E E 53 G726 16k E E E El E E E G726 24k E E E El E E El G726 32k E El E E E El G726 40k E E E E E E E ee Codec A CODEC is an algorithm for taking voice or video and compressing the information This type of codec combines analog to digital conversion and digital to analog conversion functions in a single chip The Codec is used to compress the voice signal into data packets Each Codec has different bandwidth requirement There are 9 kinds of codec G 711 Ulaw G 711 Alaw G 729 G 723 5 3k 6 3k bps G 726 16K bps G 726 24K bps G 726 32K
7. com for your server e g Web server from a DDNS server The outside users can always access the web server using the www ata com regardless of the WAN IP When you want your internal server to be accessed by using DNS name rather than using the dynamic IP address you can use the DDNS service The DDNS server allows to alias a dynamic IP address to a static hostname 42 VoIP ATA with router function User Manual Unlike DNS that only works with static IP addresses DDNS works with dynamic IP addresses such as those assigned by an ISP or other DHCP server DDNS is popular with home networkers who typically receive dynamic frequently changing IP addresses from their service provider DDNS is a method of keeping a domain name linked to a changing dynamic IP address With most Cable and DSL connections you are assigned a dynamic IP address and that address is used only for the duration of that specific connection With the TA 201 you can setup your DDNS service and the ATA will automatically update your DDNS server every time it receives a different IP address Dynamic DNS Dynamic DNS Setup Enable DONS Service Provider Domain Name User Name Email Password Key IP Address Update Policy Use WAN IP Address Auto Detect DUT IP Address D Use specified IP Address Reset oEnable Enable Disable the DDNS service default setting is Disable ODDNS Server Type The IPG 110 support two types of DDNS DynDns
8. org or TZO net ODomain Name The hostname which you register in DynDns org or TZO net website ODDNS Username The username which you register in DynDns org or TZO net website ODDNS Password The password which you register in DynDns org or TZO net website 6 2 Tools Configuration This page allows you save current settings to a file or reload the settings from the file which was saved previously Besides you could reset the current configuration to factory default 43 VoIP ATA with router function User Manual Maintenance gt Tools gt Configuration Configuration Uparac To restore a previously saved configuration file to your system browse to the location of the configuration file and click Upload Bade Path Click Reset to clear all user entered configuration information and return to factory defaults After resetting the LAN IP address will be 192 168 1 1 DHCP will be reset to server Upgrade Firmware This page allows you upgrade the Access Point firmware to new version Please note do not power off the device during the upload because it may crash the system Maintenance gt Tools gt Upgrade Firmware Upgrade Firmware upgrade the internal router firmware browse to the location of the binary fw upgrade file and click Upload Upgrade files can be downloaded from website In some cases you may need to reconfigure File Path Ping Test Ping function you can Ping IP or
9. page shows the current status and some basic settings of the device Click System Information to display system status The Device Information has WAN type and LAN type Phone Status more Status etc VoIP ATA System Status Device Information JS Model Type 2FXS 1WAN System Uptime Oday 0h 41m 48s Maintenance Firmware Version sunnyline_tab_106 Current Date Time Mon Feb 20 11 53 03 2012 System Resource WAN Information CPU Usage E 0 WAN Access Type Static IP Memory Usage 36 IP Address 0 0 0 0 IP Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 MAC Address 00 O0f fd Se 00 28 LAN Information IP Subnet Mask 255 255 255 0 Default Gateway 192 168 1 1 WAN Soe N A MAC Address 00 0f fd 5e 00 29 LAN Up 100m DHCP Server Enabled DHCP Table Details Packet Statistics Details sre account Registration Pure Phone 1 UnRegister 503 Service Unavailable 6000 serwer sip com Phone 2 UnRegister 503 Service Unavailable 6001 serwer sip com This page displays the current information for the device It will display the LAN WAN and system firmware information This page will display different information for you according your WAN setting Static IP DHCP PPPoE PPTP If your WAN connection is set up for Dynamic IP address there will be a Release button and Renew button Use Release to disconnect from your ISP and use Renew to connect to your ISP If
10. router function User Manual you are connected to the Internet through a DSL line check with your ISP to see if they use PPPoE If they do you need to select this item i 8 level TTL 941 fi WAN Interface Setting This page is used to configure the parameters for Internet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE by click the item walue of WAN Access type WAN Access Type PPPoE User Name Password PPPoE User Name Enter User Name provided by your ISP PPPoE Password Enter Password provided by your ISP Confirmation Password Enter Password to confirm again Step 6 Voip Setup 3 G8 level Welcome to the Wizard Setup CONNECTION WIZ ARDO The connection wizard will walk you through the most common configuration options This wizard has been broken down into two steps each of which may hawe multiple pages Wot SETUP The voip wizard will walk you through the most common configuration options 16 VoIP ATA with router function User Manual f Configuration SIP Number SIP Server Address SIP Service Domain User Name Password OSIP Number you need to input the User Name get from your ISP OSIP Server add you need to input the Proxy add get from your ISP 5 Server Domain you need to input the SIP Domain get from your ISP oUser Name you need to input the Re
11. send fax messages as UDP packets through IP networks This provides better quality but it may have inter operability problems The peer devices must also use T 38 Session Timer Enable Select Enable if you want to define how long the IPG 110 IPG 200 waits to receive a session alive packet for a voice session from the SIP server Minimum Expiration Time Enter the minimum time the IPG 110 IPG 200 waits for a session alive packet 90 65536 seconds If a session alive packet is not received during this time the voice session is terminated Maximum Expiration Time Enter the maximum time the IPG 110 IPG 200 waits for a session alive packet 90 65536 seconds If a session alive packet is not received during this time the voice session is terminated MWI Message Waiting Indications Active Select this if you want to hear a waiting beeping dial tone on your phone when you have at least one voice message Your SIP service provider must support this feature Expiration Time Keep the default value unless your SIP service provider tells you to change it Enter the number of seconds the SIP server should provide the message waiting service each time the IPG 110 IPG 200 subscribes to the service Before this time passes the IPG 110 IPG 200 automatically subscribes again DND Do Not Disturb DND Mode Always Enable Disable From hh mm To hh mm Block Anonymous Call Block Anonymous Call Enable DND Setting DND Setting you
12. the pull down menu default is 255 255 255 0 DHCP Server Setting DHCP stands for Dynamic Host Control Protocol The DHCP server gives out IP addresses when a device is starting up and request an IP address to be logged on to the network The device must be set as a DHCP client to Obtain the IP address automatically By default the DHCP Server is enabled in the unit The DHCP address pool contains the range of the IP address that will automatically be assigned to the clients on the network DHCP client computers connected to the unit will have their information displayed in the DHCP Client List table The table will show the Type Host Name IP Address MAC Address Description and Expired Time of the DHCP lease for each client computer DHCP Server is a useful tool that automates the assignment of IP addresses to numbers of computers in your network The server maintains a pool of IP addresses that you use to create scopes A DHCP scope is a collection of IP addresses and TCP IP configuration parameters that are available for DHCP clients to lease Then the server automatically allocates these IP addresses and related TCP IP configuration settings to DHCP enabled clients in the network The DHCP Server leases the IP addresses to clients for a period that you specify when you create a scope A lease becomes inactive when it expires Through the DHCP Server you can reserve specific IP addresses permanently for hardware devices that must have a St
13. 0 bytes Enable PPTP DNS Servers First DNS Server 0 0 0 0 Second DNS Server 0 0 0 0 Clone MAC Address Clone the computer s MAC address IP Address 0 0 0 0 Use specified MAC Address o00000000000 Other Setting E Enable uPNP DHCP client Dynamic Host Configuration Protocol DHCP Dynamic IP Get WAN IP Address automatically If you are connected to the Internet through a Cable modem line then a dynamic IP will be assigned Note WAN port gets the IP Address Subnet Mask and default gateway IP address automatically if DHCP client is successful 19 VoIP ATA with router function User Manual Network gt WAN gt Internet Connection Internet Connection ISP Parameters for Internet Access WAN Access Type Dynamic IP Type Setting Host Name MTU Size 1412 1400 1492 bytes E Enable PPTP DNS Servers Assign DNS Dynamically 9 User Defined DNS First DNS Server 0 0 0 0 Second DNS Server 0 0 0 0 Clone MAC Address Clone the computer s MAC address IP Address 0 0 0 0 r Pre Use specified MAC Address 000000000000 Other Setting E Enable uPNP PPPoE Point to Point Protocol over Ethernet PPPoE Some ISPs provide DSL based services and use PPPoE to establish communication link with end users If you are connected to the Internet through a DSL line check with your ISP to see if they use PPPoE If they do you need to make sure the following items PP
14. 6 1 3 6 Wed Feb 22 13 19 00 CST 2012 Feb Feb 35 Feb Feb Feb Feb Feb Feb Feb Feb Feb Feb Feb Feb 20 20 20 20 20 20 20 20 20 20 20 20 11 11 44 11 11 44 11 11 44 11 11 44 17533544 11 11 44 11 11 44 11 11 44 2237251 a7 11158 T system all Enable Remote Log CPU revision is 0000ff00 Determined physical RAM map memory 02000000 00000000 usable User defined physical RAM map memory 02000000 00000000 usable Initrd not found or empty disabling initrd On node totalpages 8192 DMA zone 64 pages used for memmap DMA zone 0 pages reserved 32m 408 36 Om VoIP Feature 32m 408 73 Om VoIP Feature 32m 408 74 Om VoIP Feature Oxb2f3200 Oxb2f3200 Oxb2f3200 Log Server IP Address E 46 VoIP ATA with router function User Manual Logout If you need to logout administrator right for web access please click the Logout link The web system management interface will auto logout with 1800 sec default value x VoIP ATA System Status 2FXS 1WAN 1LAN time Oday 0h 41m 48s sunnyline_tab_106 Current Date Bs Mon Feb 20 11 53 03 2012 System Resource C 36 Summary Status ee ee E UnRegister 503 Service Unavailable 6000 serwer sip com 503 Service Unavailable 6001 serwer sip com 47 VoIP ATA with router function User Manual Information System Information System Status This
15. Analogue Telephone Adapter IPG 110 allows 1 2 lines analog voice and fax communication over a traditional data communications data networking digital Internet Model FXO Port PSTN _ FXS Port AN Port LAN Port RJ 11 port SIP 1 5 Front Panel LED Indicators amp Rear Panels IPG 200 LED State Description 1 POWER On IPG 200 is power ON Off IPG 200 is power Off 2 LAN port On LAN is connected successfully Flashing Data is transmitting Off Ethernet not connected to PC 3 WAN port On IPG 200 network connection established Flashing Data traffic on cable network Off Waiting for network connection 4 FXS Phone Off Telephone Set is On Hook Flashing Ring Indication On Telephone Set is Off Hook IPG 110 VoIP ATA with router function User Manual LED State Description 1 POWER On IPG 110 is power ON Off IPG 110 is power Off 2 LAN port On LAN is connected successfully Flashing Data is transmitting Off Ethernet not connected to PC 3 WAN port On IPG 110network connection established Flashing Data traffic on cable network Off Waiting for network connection 4 FXS Phone Off Telephone Set is On Hook Flashing Ring Indication On Telephone Set is Off Hook 5 FXO Line Off Line is On hook On Line is In Use 1 6 IPG 200 IPG 110 Specification VoIP Key Features Support SIP protocols SIP Registration and Digest Authentication smart VoIP call Dialing Book VoIP call Book could provide any application VoIP call to any type des
16. CFAI NEXT LEVEL IN NETWORKING www 8level eul USER MANUAL IPG 200 IPG 110 VoIP ATA w router function V1 0 20120227 VoIP ATA with router function User Manual Table of Contents TABLE OP CONTENIS sscssesssasteceedtecedduinciesutituise suautiaan i aat 1 1 OVERVIEW 1 2 AUDIENCE 1 3 ACRONYMS TABLE 1 4 INTRODUCTION 1 5 FRONT PANEL LED INDICATORS amp REAR PANELS 1 6 IPG 200 IPG 110 SPECIFICATION INSTALLATION AND SETUP cicien tiaa 2 1 PACKAGE CONTENT 2 2HARDWARE INSTALLATION 2 4 WIZARD SETUP NETWORK SETTING icini a eaa 3 1 WAN INTERFACE STATIC IP DHCP CLIENT PPPOE PPTP WITH WAN Static DHCP PPPOE L2TP WITH WAN Static DHCP PPPOE ONLY IPG 110 3 2 LAN INTERFACE 3 3 NAT PORT FORWARDING VOIP SETTING IPG 200 IPG 1 10 i o oiis iisa aiaia 10 11 13 18 18 18 19 20 21 21 22 23 24 25 Qos 4 2 PHONE COMMON REGION 4 3 PHONE BOOK SPEED DIAL DIAL PLAN WITH URL SECURITY cine aaaea b aaao aa taa aaa 5 1 FIREWALL IP FILTERING 31 32 35 36 36 36 37 38 38 38 Mac FILTERING PORT FILTERING CONTENT FILTERING MAINTENANCE nni 6 1 SYSTEM GENERAL TIME SETTING AUTO PROVISION DDNS 6 2 TOOLS CONFIGURATION UPGRADE FIRMWARE PING TEST PING FUNCTION YOU CAN PING IP OR DOMAIN 6 3 LOG LOGOUT INFORMATION iicet adai SYSTEM STATUS IWRCONVIMAND
17. D User Priority Defines user priority giving eight 2 3 priority levels IEEE 802 1P defines the operation for these 3 user priority bits Usually this will be defined by your service provider When you enable the first VLAN Packets and set the VID User Priority then all the incoming packets with the TA s IP address and the same VID will be accept by the TA If the incoming packets with the TA s address but the different VID then the packets will be discard by the IPG 110 The Other incoming packets with different IP address will go through the LAN port to the PC 4 2 Phone Analog Phone Select Phone 1 or Phone 2 first then click the Advance Setup button Analog Phone Port Setting Phone 1 Outgoing Call Use SIPi SIP2 Incoming Call apply to SIP1 Fl sip Reset Advanced Setup 32 VoIP ATA with router function User Manual Advanced Setup Phone Port 1 Jitter Buffer Size Min delay ms 60 Max delay ms 200 Voice Activity Detection VAD E Enable Jitter Buffer Control In IPG 110 IPG 200 VoIP device The jitter buffer control is a shared data area where voice packets can be stored collected and sent to the voice shared Buffer in evenly spaced intervals modify in packets arrival time called jitter can occur because of network congestion timing drift or route changes delay ms Select min delay buffer time 40ms 100 ms 4 delay ms
18. Domain 44 VoIP ATA with router function User Manual Ping Test Ping Test Ping Destination Apply EX Ping 168 95 1 1 and response as follow PING 168 95 1 1 168 95 1 1 56 data bytes 64 bytes from 168 95 1 1 icmp_seq 0 ttl 247 time 80 0 ms 64 bytes from 168 95 1 1 icmp_seq 1 ttl 247 time 100 0 ms 64 bytes from 168 95 1 1 icmp_seq 2 ttl 247 time 240 0 ms 64 bytes from 168 95 1 1 icmp_seq 3 ttl 247 time 30 0 ms 168 95 1 1 ping statistics 5 packets transmitted 4 packets received 20 packet loss round trip min avg max 30 0 112 5 240 0 ms Restart Restart function you can restart thelPG 200 IPG 110 device If you want to restart the IPG 200 IPG 110 you can just click the Reboot button than the VoIP Phone will automatically If for any reason the device is not responding correctly you may want to restart the IPG 200 IPG 110 system System Restart Click Restart to have the device perform a software restart The SYS or PWR LED blinks as the device restarts and then stays steady on if the restart is successful 45 6 3 Log VoIP ATA with router function User Manual If you want to Log the IPG 110 IPG 200 system log you can enable log and enable system all The system will record system log Maintenance gt Log gt System Log System Log W Enable Log 20 11 11 44 klogd started BusyBox v1 8 2 2012 02 22 11 54 11 CST 20 11 11 44 Linux version 2 6 19 root desktop gcc version 3 4
19. N interface for Internet access and remote access The following sections will explain more details of WAN Port Internet access and broadband access setup When you click WAN Port Type Setup from within the Wizard Setup the following setup page will be show Three methods are available for Internet Access Fixed IP User If you are a leased line user with a fixed IP address fill out the following items with the information provided by your ISP m GS level WAN Interface Setting This page is used to configure the parameters for Internet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE by click the item value of WAN Access type WAM Access Type Static IP Subnet Mask Default Gateway 5 WAN IP Address check with your ISP provider subnet mask check with your ISP provider Default Gateway check with your ISP provider DHCP Client Dynamic IP Get WAN IP Address automatically Slevel WAN Interface Setting This page is used to configure the parameters for Internet network which connects to the WAN port of your Access Point Here you may change the access method to static IP DHCP PPPoE by click the item walue of WLAN Access type ADSL Dial Up User PPPoE Enable Some ISPs provide DSL based service and use PPPoE to establish communication link with end users If 15 VoIP ATA with
20. Outbound Proxy Address Enable Disable Register Outbound Proxy server and input the Outbound Proxy Address get from your ISP You can see the Register Status in the Status item If the item shows Registered then your VoIP Phone is registered to the ISP you can make a phone call directly If you have more than one SIP account you can following the steps to register to the other ISP When you finished the setting please click the Apply button OUser Name you need to input the Register Name get from your ISP oOPassword you need to input the Register Password get from your ISP STUN Traversal STUN Simple Traversal of UDP through NATs Network Address Translation is a protocol for assisting devices behind a NAT firewall or router with their packet routing 2 VoIP ATA with router function User Manual STUN enables a device to find out its public IP address and the type of NAT service its sitting behind When you enable the STUN function you must input the STUN server address NAT Traversal STUN E Enable STUN Server Address STUN Server Port H78 SIP Advance DIP a l SIP Advanced SIP Port 5060 Media Port 9000 Packetization 20m DTMF Relay PCM 2833 Payload Type SIP INFO Duration ms Call wait time 0 O 128 seconds Call Waiting E Enable DNS SRV E Enable Prohibit coming calls from other SIP server Enable oOSIP Port Number Assign the SIP port number of IPG 110 IPG 200 default sett
21. PoE User name Enter username provided by your ISP PPPoE Password Enter password provided by your ISP Ss sss wee Network gt WAN gt Internet Connection Internet Connection ISP Parameters for Internet Access WAN Access Type PPPoE Y Type Setting User Name Password Service Name Connection Type Mailed Up z Connect _Disc iiare Idle Timeout 1 1000 minutes MTU Size 1492 1360 1492 bytes DNS Servers Assign DNS Dynamically User Defined DNS First DNS Server 0 0 0 Second DNS Server 0 0 0 0 20 VoIP ATA with router function User Manual PPTP with WAN Static gt DHCP PPPoE Some ISPs provide DSL based service and use PPTP with Static DHCP or PPPoE to establish communication link with end users Internet Connection ISP Parameters for Internet Access WAN Access Type Static IP Type Setting IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 MTU Size 1500 1400 1500 bytes IW Enable PPTP Serwer IF Address User Name Password MTU Size 1400 280 1400 bytes IM Request MPPE Encryption mPPTP Server IP Address check with your VPN PPTP Server provider mPPTP User Name PPTP Dial in account mPPTP Password PPTP Dial in Password mPPTP MTU Size mRequest MPPE Encryption mRemote LAN setting select SIP Call by LAN IP Address or not L2TP with WAN Static gt DHCP PPPoE only IPG 110 Some ISPs provide D
22. SL based service and use L2TP with Static DHCP or PPPoE to establish communication link with end users VPN Type Setting Enable PPTP Enable L2TP LOTP Server IP Address L2TP User Name fs L2TP Password fs L2TP MTU Size 1400 1500 bytes Remote LAN setting SIP Call by LAN IP Address mL2TP Server IP Address check with your VPN PPTP Server provider mL2TP User Name L2TP Dial in account mL2TP Password L2TP Dial in Password mL2TP MTU Size mRequest MPPE Encryption mRemote LAN setting select SIP Call by LAN IP Address or not 21 VoIP ATA with router function User Manual 3 2 LAN Interface These are the IP settings of the LAN Local Area Network interface for the device These settings may be referred to as private settings You may change the LAN IP address if needed The LAN IP address is private to your internal network and cannot be seen on the Internet The default IP address is 192 168 1 1 with a subnet mask of 255 255 255 0 LAN is a network of computers or other devices that are in relatively close range of each other For example devices in a home or office building would be considered part of a local area network LAN Setup LAN TCP IP IP Address 192 168 1 1 Subnet Mask 255 255 255 0 DHCP Server Enabled DHCP Client Range 192 168 1 33 192 168 1 65 Reset IP Address Assign the IP address of LAN server default is 192 168 1 1 oOSubnet Mask Select a subnet mask from
23. Select Max delay Buffer time 130ms 300ms HOOptimization factor Controls quickly the length of the Jitter Buffer is increased when Voice RTP on the network Default is 7 OVoice Active Detector It is used in speech encoding software to determine if the voice being encoded is human speech or background noise Voice Activity Detection If this function is enabled when silence is occurred for a period of time no data will be sent across the network during this period in order to save bandwidth If you use Asterisk please disable Silence Compression it maybe make you call disconnect G 166 Echo cancelation LEC Tail Length ms 2 Worce Volume Control Listening Wolume 3 32 31 Mute 32 Speaking Volume 3 32 31 Mute 32 G 168 Echo cancelation Select the tail lengths of 1ms 2ms 4ms 8ms 16ms 32ms Voice Volume control o Phone In Speaker Voice Gain db Sets a specific sound intensity for receiving sound Select a level from 32 to 31 o Phone out MIC Voice Gain db Sets a specific sound intensity for transmitting sound Select a level 33 from 32 to 31 Loop Current Loop Current Polarity Reversal Polarity Reversal Loop Current Select the loop current Polarity Reversal As Callee Answer Check this box to generate line polarity reversal while the remote user picks up the phone call As Callee On Hook Check this box to generate line polarity reversal while the remote user hangs off th
24. al VOIP Setting IPG 200 IPG 110 SIP is a request response protocol dealing with requests from clients and responses from servers Participants are identified by SIP URLs Requests can be sent through any transport protocol SIP determines the end system to be used for the session the communication media and media parameters and the called party s desire to engage in the communication Once these are assured SIP establishes call parameters at either end of the communication and handles call transfer and termination SIP Setting Phone Phone book PSTN Line IPG 110 only IPG 200 SIP Settings SIP Setting Copy SS Ee eee SIP i 6000 6000 Serwer sip com CopyToSiP2 SIP 2 6001 6001 serwer sip com Ee CopyToSiPt NAT Traversal STUN Enable STUN Server Address STUN Server Port 2478 25 VoIP ATA with router function User Manual IPG 110 SIP Settings SIP Setting Phone n 6000 6000 serwer sip com m CopyToSe2_ Lipe 6011 6111 serwer gip eom LH CopyToSF1 Adnvanced Setting PSTN Call To Phone LJ friable HAT Traversal STUN Enable STUN Server Address STUN Server Port 3478 4 1 SIP Setting Sip setting In SIP Settings you can setup the Service Domain Port Settings Codec Settings Codec ID Settings RTP Setting RPort Setting and Other Settings If the VoIP service is provided by ISP you need to setup the related information correctly then you can register to th
25. any other setting DMZ Virtual Server by router side If you use STUN Outbound Proxy you must have a STUN Outbound Proxy Server to support If they can t pass NAT please open the DMZ Virtual Server by Router NAT Firewall 50 VoIP ATA with router function User Manual B Scenario Application Samples Router VoIP Gateway 7 Mobile Phone Softswitch SoftPhone ATA Gateway 91
26. atic IP address e g a DNS Server An advantage of using DHCP is that the service assigns addresses dynamically The DHCP Server returns addresses that are no longer in use to the IP addresses pool so that the server can reallocate them to other machines in the network If you disable this DHCP you would have to manually configure IP for new computers keep track of IP addresses so that you could reassign addresses that clients aren t using and reconfigure computers that you move from one subnet to another The DHCP Static MAP table lists all MAC and address which are active now When you enable the DHCP server 2 VoIP ATA with router function User Manual OAssigned DHCP Address Enter the starting IP address for the DHCP server s IP assignment and the ending IP address for the DHCP server s IP assignment CIDHCP Lease Time Assign the length of time for the IP lease default setting is 86400 seconds DHCP Table DHCP Table ST 192 168 1 33 3 d8 5d 4c 80 37 81 3 3 NAT A Demilitarized Zone is used to provide Internet services without sacrificing unauthorized access to its local private network Typically the DMZ host contains devices accessible to Internet traffic such as Web HTTP servers FTP servers SMTP e mail servers and DNS servers Port Forwarding Default Server Setup Default Server 0 0 0 0 Forward Setting Enable Port Forwarding IP Address Protocol Port Rang
27. cument is intended for system vendor who are using IPG 200 IPG 110 to build an Internet telephony gateway or server application It is assumed that the reader has the general knowledge of VolP applications and products 1 3 Acronyms Table Application Interface DAC DHCP Dynamic Host Configuration Protocol _ Dynamic Domain Name System DNS Domain Name System Network Address Translation Point to Point Tunneling Protocol Foreign Exchange Station i Wide Area Network DPTE Protocol also known as RTP control protocol Real Time Transport Protocol SLIC Subscriber Line Interface Circuit Network Time Protocol RTCP Real Time Transport Control Session Initiation Protocol UR i Uniform Resource Identifier Simple Traversal of UDP through UDP i User DSR 100gram Protocol Transmission Control Protocol V Voice Over Internet Protocol 1 4 Introduction This Analogue Telephone Adapter IPG 200 IPG 110 provides a total solution for integrating voice data network and PSTN The IPG 200 Analogue Telephone Adapter IPG 200 support SIP VoIP Protocol The IPG 200 Analogue Telephone Adapter IPG 200 allows 1 2 lines analog voice and fax communication over a traditional data communications data networking digital Internet VoIP ATA with router function User Manual Model___FXOPort PsTN FXS Port WAN Port LAN Port manen pe The IPG 110 Analogue Telephone Adapter IPG 110 support SIP VolP Protocol The IPG 110
28. e Comment Reset Current Forward Table Reset DMZ In computer networks a DMZ Demilitarized Zone is a computer host or small network inserted as a neutral zone between a company s private network and the outside public network It prevents outside users from getting direct access to a server that has company data Think of DMZ as the front yard of your house It belongs to you and you may put some things there but you would put anything valuable inside the house where it can be properly secured Setting up a DMZ is very easy If you have multiple computer s you can choose to simply place one of the computers between the Internet connection and the firewall If you have a computer that cannot run Internet applications properly from behind the device then you 2 VoIP ATA with router function User Manual can allow the computer to have unrestricted Internet access Enter the IP address of that computer as a DMZ host with unrestricted Internet access Adding a client to the DMZ may expose that computer to a variety of security risks so only use this option as a last resort Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Gateway s NAT firewall 24 VoIP ATA with router function User Manu
29. e SIP Proxy Server correctly In Service Domain Function you need to input the account and the related information in this page please refer to your ISP provider You can register three SIP account in the VoIP Phone You can dial the VoIP phone to your friends via first enable SIP account and receive the phone from these three SIP accounts 26 VoIP ATA with router function User Manual SIP 1 Setting W Active SIP Account Account Name 6000 Number 6000 SIP Display Name SIP Server Address serwer sip com E Backup Sip Proxy Server SIP Server Port S060 1 65535 SIP Service Domain Register Expire sec 60 Outbound Proxy Server E Enable Outbound Proxy Address Outbound Proxy Port 3060 1 65535 Authentication User Name 6000 Password SERRE R BR EB Apply Reset Advanced z oAccount Name you can input the name you want to display oNumber you need to input the User Name get from your ISP OSIP Display Name you can input the name you want to display oSIP Server Addr Enable Disable Register Proxy server and input the Proxy Addr get from your ISP OSIP Server Port you need to input the Proxy Port get from your ISP 5 Server Domain you need to input the SIP Domain get from your ISP OReg Expire sec SIP registration expired time HOutbound Proxy Server you need to input the Outbound Proxy get from your ISP If your ISP does not provide the information then you can skip this item O
30. e of such filters can be helpful in securing or restricting your local network IP Filtering Filter Setting Enable IP Filtering Local IP Address Protocol Comment Reset Current Filter Table Reset o Enable Disable Filtering The IP address filter function control a network IP address from your local network to Internet through the Gateway default setting is disable Mac Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network 38 VoIP ATA with router function User Manual Security gt Firewall gt MAC Filtering e TD Filtering MAC Filtering E Enable MAC Filtering MAC Address Comment OMAC Enable Disable from your local network to Internet through the Gateway MAC filter function default setting is disable Port Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Use of such filters can be helpful in securing or restricting your local network Security gt Firewall gt Port Filtering IP Filtering MAC Filtering Port Filtering Enable Port Filtering PortRange Protocol Comment 39 VoIP ATA with router function User Manual Content Filtering URL filter is used to deny LAN users from accessing the in
31. e phone call Caller ID setting Caller ID Mode FSK Date amp Time Sync Short Ring before Caller ID Dual Tone before Caller ID Caller ID Prior First Ring Caller ID DTMF Start Digit Caller ID DTMF End Digit Private Caller ID Hook Flash Timing Minimum on hook time Maximum on hook time Hot Line Use Hot Line Hot Line Timer Hot Line Number VoIP ATA with router function User Manual 22 E Enable E Enable E Enable E Enable Enable DTMF_A E Enable 80 Minimum 30 ms 500 Maximum 2000 ms E Enable 3 0 30 seconds 34 VoIP ATA with router function User Manual Caller ID Mode FSK Date amp Time Sync Send FSK Date amp Time to display device Reverse Polarity before Caller ID Send Reverse Polarity before Caller ID Short Ring before Caller ID Send short ring before caller ID Dual Tone before Caller ID Send Dual Tone before Caller ID Caller ID prior First Ring Send Caller ID before first ring Caller ID DTMF Start Digit Set Caller ID DTMF start digit Caller ID DTMF END Digit Set Caller ID DTMF start digit Hook Flash Timing Minimum on hook time default 30 ms Maximum on hook time default 2000 ms Hot Line This service allows you to make a call to a pre programmed number by only lifting the handset Common Common Pulse Dial Detection Disable Enable Interdigit Pause Duration 450 msec Dailing Parameter Ww Auto Dial T
32. er No Answer Forward to Off Enable No Answer Number No Answer Time sec 5 Forwarding Mode You can setup the phone number you want to forward in this page There are three type of Forward mode You can setup Immediate Forward Busy Forward and No Answer Forward by click the icon Immediate Forward All incoming call will forward to the number you entered You can input the phone number If you select this function then all the incoming call will direct forward to the speed dial number you entered Busy Forward If you are on the phone the new incoming call will forward to the number you entered No Answer Forward If no one picks up the phone the incoming call will forward to the number you entered When you finished the setting please click the Submit button Fax Option G 711 Fax Passthrough O 7 38 Fax Relay P Asserted Identity P Asserted Identity E Enable Dial Termination Key Enable eg Dial Termination Key Session Timer E Enable Minimum Expiration Time 20 Min 90 Max 65536 Default 90 sec Maximum Expiration Time 1800 Min 90 Max 65536 Default 1800 sec MWI Message Waiting Indication E Active Expiration Time 1800 1 65535 sec FAX Option G 711 Fax Pass through Select this if the IPG 110 IPG 200 should use G 711 to send fax messages The peer devices must also use G 711 29 VoIP ATA with router function User Manual T 38 Fax Relay Select this if the IPG 110 IPG 200 should
33. gement over the IP Network Web Base firmware upgrade Backup and Restore Configuration file Different Account Login Back to Factory Default Time setting Auto Provision Auto config Auto FW updrade Ping Test Security Firewall IP Filter MAC Filter URL Filter Port Filter General Specification AC power AC100V 240V DC12V 1A 50 60 Hz Temperature 0 C 40 C Operation Humidity up to 90 non condensing Emission FCC Part 15 Class B CE Mark RoHS Compliant Dimension 115 x 85 x 29 mm Weight 165 g VoIP ATA with router function User Manual VoIP ATA with router function User Manual Installation and Setup 2 1 Package Content Please check enclosed product and its accessories before installation Refer to the item number These contents are from pre released product The contents for the final product might change a little bit IPG 200 Package VoIP ATA IPG 200 RJ 45 AC Power Adapter DC12V 1A QIG CD Rom User manual IPG 110 Package ine al VoIP ATA IPG 110 RJ 45 AC Power Adapter DC12V 1A QIG CD Rom User manual 10 VoIP ATA with router function User Manual 2 2Hardware Installation Port Description DEMO Model IPG 200 AC RES WAN LAN FXS_1 FXS 2 Port Description DEMO Model IPG 110 AC Res WAN LAN FXS FXO 1 FXS Foreign Exchange Station FXS port can be connected to analog telephone sets or Trunk Line of PBX PSTN FXO Connect to PBX or CO line wit
34. gister User Name get from your ISP you need to input the Register Password get from your ISP Step 7 Finishing the Wizard Setup Ls O8level METT LATI BT Congratulation The Voip Wizard configuration is complete wait a few seconds the sip will be registered Having Voip Access problems 1 Verify your settings in this wizard 2 If your wizard entries are correct but still cannot access the Internet then check that your SIP account is active and that the settings you entered in the wizard are correct 3 If you still have problems please contact customer support Phone Phone a Go to Connect Setup Wizard 17 VoIP ATA with router function User Manual Network Setting WAN Interface LAN Interface NAT 3 1 WAN Interface WAN Wide Area Network is a network connection connecting one or more LANs together over some distance For example the means of connecting two office buildings separated by several kilometers would be referred to as a WAN connection The size of a WAN and the number of distinct LANs connected to a WAN is not limited by any definition Therefore the Internet may be called a WAN WAN Settings are settings that are used to connect to your ISP Internet Service Provider The WAN settings are provided to you by your ISP and often times referred to as public settings Please select the appropriate option for your specific ISP For most users Internet access is the pr
35. h RJ 11 Gray analog line FXO port was connected to the extension port of a PBX or directly connected to a PSTN line of carrier WAN Wide Area Network Connect to the network with an Ethernet cable This port allows your ATA to be connected to an Internet Access device e g router cable modem ADSL modem through a networking cable with RJ 45 connectors used on 10BaseT and 100BaseTX networks LAN Local Area Network Connect to PC with Ethernet cable 1 port allows your PC or Switch Hub to be connected to the ATA through a networking cable with RJ 45 connectors used on 10BaseT and 100BaseTX networks 5 RES Reset button Push this button until 3 seconds and ATA will be set to factory default configuration 6 AC power DC in 12V A power supply cable is inserted 1 VoIP ATA with router function User Manual Installation 1 Connect the 12V DC IN to the power outlet with power adaptor 2 Connect FXO to PSTN 3 Connect FXS to a telephone jack with the RJ 11 analog cable Connecting to a PC 1 Connect the Ethernet cable with RJ 45 connector to any LAN port 2 Connect the other end of the Ethernet cable to your PC s installed network interface card NIC Connecting to an External Ethernet Hub or Switch 1 Connect the Ethernet cable with RJ 45 connector to WAN port 2 Connect the other end of the Ethernet cable to DSL Cable modem or the external Ethernet hub or switch 2 3 Quick Start How to set your network envi
36. imary application IPG 200 IPG 110 supports the WAN interface for internet access and remote access The following sections will explain more details of WAN Port Internet access and broadband access setup When you click WAN Setting the following setup page will be shown Three methods are available for Internet Access Static IP DHCP PPPoE PPTP with WAN Static gt DHCP PPPoE Status vastness Internet Connection ISP Parameters for Internet Access WAN Access Type Dynamic IP Urns T Static IP Security Type Setting Dynamic IP PPPoE Maintenance Hact Mama Static IP If you are a leased line user with a fixed IP address enter in the IP address subnet mask gateway address and DNS domain name server address es provided to you by your ISP Each IP address entered in the fields must be in the appropriate IP form which are four IP octets separated by a dot x x x x The Router will not accept the IP address if it is not in this format Example 168 95 1 1 m P Address Check with your ISP provider mSubnet Mask Check with your ISP provider mDefault Gateway Check with your ISP provider VoIP ATA with router function User Manual Network gt WAN gt Internet Connection Internet Connection f 1 ISP Parameters for Internet Access WAN Access Type Static P Type Setting IP Address 0 0 0 0 Subnet Mask 0 0 0 0 Default Gateway 0 0 0 0 MTU Size 1500 1400 150
37. ime 3 9 sec 0 is disable Off Hook Alarm Off Hook Alarm Time 15 10 60 sec 0 is disable Apply Reset Dialing Parameter gAuto Dial Time If no other number is being dialed within this interval the IPG 110 will terminate this call Assign the time interval from 1 to 9 seconds Off Hook Alarm OOff Hook Alarm Time Set has been off hook after this time user will hear alarm 5 VoIP ATA with router function User Manual Region i te el VoIP gt Phone gt Region i Analog Phone l Common Region Region Settings Country PO LAND Call Service Mode USA Type T Customer Ring Setting Ring Setting Enable Cadence ON msec 1500 Cadence OFF msec 1500 Region Setting Adjust the tone frequency according to each country Select a country from the pull down menu 4 3 Phone Book Speed Dial Speed Dial lets you define a button or a set of buttons to link to a specific number defined in Speed Dial list VoIP gt Phone Book gt Speed Dial Speed Dial Dial Plan with URL Port Setting Phone 1 Speed Dial Position Name phone Number H Eo o o fs LJ E E H a 07 H E 09 10 Remove Seleced oPosition Select the speed dial shortcut to use from 0 to 9 CName Phone number note oPhone Number Enter the international number to dial 36 VoIP ATA with ro
38. ing is 5060 OMedia Port Start The starting range of port for RTP Port number for initial of sending RTP packet default setting is 9000 OiPacketization Select the voice codec packetization interval in milliseconds The default is 20 ms This is used to minimize loss that happens during transmission of voice data over the network ODTME Setting you can setup the RFC2833 Out Band DTMF Inband DTMF and Send DTMF SIP Info in this page To change this setting please follow your ISP information When you finished the setting please click the Submit button ORFC2833 Payload Type Sending the DTMF tone as a RTP payload signal The RFC2833 signaling 5 INFO Payload Type Sending the DTMF tone as a RTP payload signal The SIP INFO signaling Type Sending the DTMF tone as a RTP payload signal The Inband DTMF signaling OSIP INFO Duration ms Modify SIPINFO duration time oOCall Waiting Call Waiting Setting function If user doesn t want to be inform there is a new incoming call user can set the function off ODNS Server Select Enable to have the IPG 110 IPG 200 Device query your ISP s DNS server for a list of any available SIP servers that it maintains This is useful if your static SIP server exercise difficulties making it hard for you to make SIP calls VoIP ATA with router function User Manual Forward Setting Immediate Forward to w Of O Enable Immediate Number Busy Forward to Off Enable Busy Numb
39. min User Password esses User Account User Name user User Password Reset 4 VoIP ATA with router function User Manual Time Setting You can maintain the system time by synchronizing with a public time server over the Internet Time Setting General Setup Current Time Year 2012 Month 2 Day 20 Hour 11 Minute 48 Seccond 59 Time Zone Select GMT 01 00 Sarajevo Skopje Sofija Warsaw Zagreb v V Enable NTP client update Automatically Adjust Daylight Saving NTP server Q 192 5 41 41 North America v Manual IP Setting Reset Refresh Auto Provision Enable or disable the auto provisioning feature If enabled the phone will try to download the two configuration files from the provisioning server via HTTP on system startup Default is disabled Auto Provision Protocol Disable File Path Exp auto Expiration Time 10800 seconds Reset DDNS Dynamic DNS is a service that provides you with a valid unchanging internet domain name an URL to go with that possibly ever changing IP address The DDNS Dynamic DNS service allows you to alias a dynamic IP address to a static hostname allowing your computer to be more easily accessed from various locations on the Internet Without DDNS the users should use the WAN IP to reach internal server It is inconvenient for the users if this IP is dynamic With DDNS supported you apply a DNS name e g www TA 201
40. ronment IPG 200 IPG 110 default network environment For WAN Wan type DHCP client For LAN IP 192 168 1 1 Subnet mask 255 255 255 0 How to configure IPG 200 IPG 110 1 Configure your PC or NB to the same subnet with IPG 200 IPG 110 2 Use web browser IE Firefox link to url http 192 168 1 1 If you connect to LAN port link to url http 192 168 1 1 3 Login user name admin 4 Login password admin 5 Use this web configuration interface to configure all system functionality firstly you should change the WAN network environment to yours ip VoIP ATA with router function User Manual Analog Telephony Adapter Welcome to your ATA Configuration Interface Enter your password and click Login Username admin Password s TITT max 30 alphanumeric printable characters and no spaces Wi Note Please turn on the Javascript and ActiveX control setting on Internet Explorer when operating system is Windows XP and service pack is SP2 Login Reset How to use VoIP 1 Configure SIP user account to register your SIP proxy use web configuration SIP Settings gt Account Setting a Port Phone Number b Port Authentication User Name c Port Authentication Password d Confirmed Password 2 Configure SIP registrar server and proxy server use web configuration SIP Settings gt Server Setting a Registrar Server Address b Outbound Proxy Address 3 Make sure IPG
41. ternet Block those URLs which contain keywords listed below URL filter allows you to block sites based on a black list and white list Sites matching the black list but not matching the white list will be automatically blocked and closed Content Filter Keyword Blocking Enable URL Filtering Keyword Reset Keyword List oEnable Enable Disable the URL filter function default setting is Disable OClient IP This is the Clinet IP is LAN address OURL Filter String This is the filter URL Example http www yahoo com 40 VoIP ATA with router function User Manual Maintenance System Account setting Time Zone Auto Provision DDNS Tool Configuration Upgrade Firmware Ping Test Restart Log System Log 6 1 System General This page is used to set the Router or Bridge mode And the account to access the web server of Access Point Empty user name and password will disable the protection Note If select Bridge mode the system will disable the firewall and NAT automatically If select Bridge mode please set the Management IP Address General System Setup Mode Router O Bridge Administrator Inactivity Timer 5 minutes 0 means no timeout Manager IP Address Note 1 If change to Bridge mode the system will automatic to disable firewall and NAT 2 If change to Bridge mode Please set Management IP Address Administrator Account User Name ad
42. tination Domain name IP address PSTN or PBX or hunting number setting Voice channels status display This function display each port status like as On hook Off hook calling number caller s number talk duration codec Telephony Specification Voice Codec G 711 A law u law G 729 AB G 723 6 3 Kbps 5 3Kbps G 726 16 24 32 40 Kbps Call Waiting Call Forward Immediate On Busy Forward No Answer Forward Speed Dial Dial Plan With URL Multi Line Appearance VoIP ATA with router function User Manual DTMF Relay PCM SIP INFO Out of band DTMF Relay RFC2833 DND Hot Line Jitter Buffer Control DNS Server FAX T 38 Session Timer MWI Message Waiting Indicator IP Specification SIP RFC 3261 SDP RFC 2327 Symmetric RTP STUN RFC3489 ENUM RFC 2916 RTP Payload for DTMF Digits RFC2833 Outbound Proxy Support WAN PPPoE client DHCP client Fix IP Address PPTP L2TP with WAN Static gt DHCP PPPoE DDNS DynDNS TZO QoS IP TOS IP Precedance DiffServ SIP DSCP RTP DSCP VLAN Call Features Volume 32 db 30 db VAD Voice Activity Detection Caller ID Generation DTMF CID Bellcore CID ETSI CID BT CID NTT CID Peer to Peer Call by Dial Plan Different Country Tone Table Region G 168 Echo cancelation Hook Flash Timing Call Transfer Pulse Dial Detection Auto Dial Off Hook Alarm Configuration amp Management Web based Graphical User Interface Remote mana
43. uter function User Manual Dial Plan With URL The Dialing plan with URL need to set when the user use the method of Peer to Peer SIP VoIP call or SIP Proxy Server Mode The SIP Dialing Plan has two kinds of directions Outgoing call out Dial Plan with URL Applied Target rule Applied Operation Priorit Lead Min Max Strip Digits Prefix Destination IP Destination SIP Select norty Number Digits Length Number URI Port Enable 1 nw O 2 m O 3 m D 3 m O 5 0 o Lead Number is the leading digits of the call out dialing number o Min Max Digits has two text fields need filled Min Length and Max Length are the min max allowed length you can dial o Strip Digits Length is the number of digits that will be stripped from beginning of the dialed number o Prefix Number is the digits that will be added to the beginning of the dialed number o Destination IP URI is the IP address Domain Name of the destination IPG 200 IPG 110 that owns this phone number o Destination SIP Port is port of the destination IPG 200 IPG 110 use Default is 5060 Call By PSTN Priority to dial from PSTN VoIP ATA with router function User Manual Security 5 1 Firewall ip Filtering 5 mac Filtering port Filtering content Filtering IP Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway Us
44. your WAN connection is set up for PPPoE there will be a Connect button and Disconnect button Use Disconnect to drop the PPPoE connection and use Connect to establish the PPPoE connection 48 VoIP ATA with router function User Manual IVR Command Can use the fxs port keypad to operator IPG 200 IPG 110 follow the instruction to listen IPG 200 IPG 110 configuration 120 Voice IP address m poenemsk Voice Network Settings 124 gateway 49 VoIP ATA with router function User Manual Appendix A FAQ List 1 What is the default administrator password to login to the IPG 200 IPG 110 How to Login A By default default username is admin default password is also admin to login to the router For security you should modify the password to protect your gateway against hacker attacks Default Wan Port Access type is DHCP Client LAN Port IP Address is 192 168 1 1 Loging Web User Interface open the Bowser IE FireFox and input IP address 2 forgot the administrator password What should do A Press the Reset button on the rear panel for over 5 seconds to reset all settings to default factory values Then you can use the default Username Password to Login Web UI 3 Why is it that can ping to outside hosts but not access Internet Web sites A Check the DNS server settings on your PC You should get the DNS servers settings from your ISP If your PC is running a DHCP client remove any
Download Pdf Manuals
Related Search