User Manual iDim Remote Control (304)
Contents
1. The exit delay will be cancelled when a new scene is manually selected Modify Light Levels using iDim Remote DALI 1 and DALI 2 scenes operate as a combination of Constant Light CL Fixed Light FL and Offset dependent on which of the 6 iDim modes that an iDim Sense is in and the scene selected It is possible to modify the DALI 1 and DALI 2 levels using the iDim Remote The adjusted levels will only be temporary unless they are stored into the already selected scene For example e f DALI 1 is a Constant Light Scene then modifying the levels will cause the Constant Light target level to be modified e f DALI 1 is a Fixed Light scene then the Fixed Light level will be modified e f operating in Constant Light Offset mode the DALI 2 level will also be affected if DALI1 is modified Please refer to table 1 overleaf for default DALI 1 and 2 scene setup for each iDim mode Other advanced configuration such as configuring the bright out level is only possible using the iDim Studio software 4 Helvar iDim Remote Control 304 User Manual Modify Light Levels using iDim Remote When modifying the constant light target levels for your system please ensure that the process is done in a darkened room or during dusk as excessive natural light may result in levels being recorded by the sensor that are not actually achievable Table 1 Default DALI 1 and DALI 2 Constant Light Fixed Light and Offset configuration for the six defa2. to store the modified levels ensure the required n 100 39 1 scene number is selected before modifying Note 2 Scene 1 is the default on scene selected by PIR movement and Solo SW1 and SW2 Note 3 When operating in Constant light Offset mode the DALI 1 and DALI 2 levels will both adjust together Doc No 7860263 iss 4 5 Stores Scenes using iDim Remote To store a modified scene using the iDim remote 1 Point the remote at a controller 2 Hold scene key 1 2 3 or 4 for 10 seconds to store scene iDim Sense LEDs will flash green if scene successfully stored The iDim mode will then flash the iDim mode number red green to signify that the iDim Sense is in User Defined mode Note Mode flash will only occur when storing scenes for the fi rst time Further scenes stores will only activate green scene store LED To exit User Defined mode and reset the iDim Sense to default mode settings the iDim Remote Control must be in special function mode Please see chapter below for more information Special Functions using iDim Remote IDim Sense LED flash feedback Example for mode 2 Single Office Mode It is possible to make the iDim Remote perform advanced tasks to assist commissioning and system testing The iDim Remote uses a special function mode where these advanced tasks can be configured This mode must be activated before a special function or test is run This avoids accidental configuration
3. 7860263 iss 4 CO 10 Hawley Mill Hawley Road EN For further information see www helvar com Dartford Kent F r weitere informationen siehe www helvar com DA2 7SY CD Lisatietoja www helvar com GB For mer information besok www helvar com ER Pour plus d informations visitez www helvar com an Per ulteriori informazioni consultare www helvar com Tel 44 0 1322 222211 RUD Iononnuurenbnytro nucpopMaunro cM Ha www helvar com Fax 44 0 1322 282216 Helvar United Kingdom Data subject to change without notice www helvar com Helvar iDim Remote Control 304 User Manual
4. changes or tests being run which could cause the light levels or scenes to be altered unintentionally Please see below for activating and deactivating special function mode See pages 7 8 for the types of special functions possible To activate special function mode Ts Remove the battery cover from the remote control 2 Using a pen or other long blunt object press mode selector button on the reverse of the iDim Remote for 3 seconds opecial function mode is now active 9 Check that the iDim Remote is in special function mode by recalling a scene The iDim Remote LED will flash orange when a function i e Scene recall is performed 4 Run the special functions that you require See pages 7 and 8 for special functions Note 1 All standard operation settings such as scene recall modify and store scene are still possible when the iDim Remote is in special function mode Note 2 Once special function mode is activated it will remain so until it is manually deactivated To deactivate special function mode 1 Hold the mode selector button for 1 second to return to standard operation Special function mode is now deactivated 2 Check that the iDim Remote is in standard operating mode by recalling a scene on the remote The iDim Remote LED should flash green when scene recall is called When a remote key is pressed during standard operation iDim Remote LED flashes green When a remote key is pressed
5. e downwards until it clicks holding the unit in place Note Remove the iDim remote by following the above procedure in reverse Doc No 7860263 iss 4 3 Connecting the iDim Remote to your PC Note 1 The iDim Remote only needs to be connected to a PC if you want to set advanced configuration settings via your PC The remote will work without iDim Studio Note 2 To download iDim Studio please visit www helvar com To connect the iDim Remote to your PC 1 Attach Mini USB connector to iDim remote 2 Connect the opposite end of the USB cable to the USB port of the PC The new device will be automatically recognised 3 Run iDim Studio if installed 2 Ti Do NOT disconnect iDim Remote when the LED is flashing red While using iDim Studio software the iDim Remote LED flashes red when device communication is in progress Do not disconnect the iDim Remote from PC during this time Switching Lights On Recall Scenes using iDim Remote To switch lights on recall a scene using the iDim remote lis Point the remote at a controller Point the remote at a controller 2 Press scene key 1 2 3 or 4 to recall the required scene To switch lights off Ts Point the remote at a controller 2 Press key on remote control to switch the lights off When lights are switched off via a remote switch or panel a 90 second exit delay will start During this time any PIR movement will extend the delay
6. efficiency intelligence ease of use iDim Remote Control 304 User Manual People Innovations Solutions Introduction The iDim Remote Control 304 can be used with the iDim Sense Standalone to modify the preset light levels and recall store scenes as well as activating special functions 100 hr Burn In PIR Walk test and Mode Identification Combined with iDim Studio the 304 iDim Remote can provide further advanced configuration Please see document iDim Studio Help or iDim User Manual D004735 for further information Note Throughout this document Controller refers to iDim Sense and or DIGIDIM Button Panels A LED indicator Flashes when comms D OK key l Mode selection button transfer is in progress and when E 1 4 Scene Recall Configuration J Battery cover buttons pressed F Function key Fn K USB connection Mini B B Up modifier G Lights off 1 C Down modifier H Transmitter Technical Specifications PC to remote USB 2 0 A Cable to USB Mini B Cable NENNEN Power supply 2 X AAA LRO3 1 5 V batteries Operating conditions O to 40 C 90 max non condensing Operating frequency 36 KHz Mechanical Data Housing Traffic White RAL 9016 Non flammable polycarbonate halogen free 409 Wall bracket screw type 2 X No 6 34 3 5 mm x 20 mm pan pozi head screws Conformity amp Standards S EMC Emission EN 6100 6 3 PEM Imm
7. he same time C If Mode 1 is in iDim Sense LEDs will flash the current mode User Defined mode Note Number and type of flashes depends on mode selected and if the iDim Sense is in User Defined mode Start Stop PIR Walk Test IDim Sense LED flash feedback To start stop PIR Walk test 4 1 Ensure the iDim Remote is in special function mode 2 Point the remote at a controller 3 Press Fn key and scene 4 at the same time iDim Sense will flash then wait for 10 s before looking for movement When movement is detected lights will go on for 5 S to transition level for 5 s off for 5 s and then return to the currently selected mode Reset Mode Note 4 The active mode flashes e g To reset a controller to factory default settings 1 Ensure the iDim Remote is in special function mode 2 flashes when mode 2 selected 2 Point the remote at a controller NC 10 s 3 Press and hold key 3 and 4 at same time for 10 seconds Note Lights will behave in the same manner as when powered up for e e the first time in the mode currently selected Doc No 7860263 iss 4 y Special Functions using iDim Remote Enable IR Receiver IDim Sense LED flash feedback To enable the Infra red receiver of a controller is Ensure the iDim Remote is in special function mode 2 Point the remote at a controller 9 Press and hold DALI 1 modifier up and Fn key at the same time for 10 seconds Disable IR Receiver IDim Se
8. in special function mode iDim Remote LED flashes orange When the iDim Remote is communicating with a PC the iDim Remote LED flashes red Do NOT disconnect during this time Helvar iDim Remote Control 304 User Manual Special Functions using iDim Remote cont Start Stop 100 hour Burn In Mode IDim Sense LED flash feedback To start or stop Burn In mode 1 Ensure the iDim Remote is in special function mode 2 Point the remote at a controller 3 Press Fn key and scene 1 at same time Lights will blink 4 times and then go to 10096 The 100 hour Burn In counter will begin 4 To stop Burn In mode press Fn key and scene 1 Note Restarting a Burn In test following a stop will cause the 100 hour Burn In time to be reset Use Resume Burn In Mode to continue a stopped Burn in test Resume Burn In Mode IDim Sense LED flash feedback To resume a stopped Burn In mode i 1 Ensure the iDim Remote is in special function mode 2 Point the remote at a controller 3 Press Fn key and scene 2 at the same time e 30 e Lights blink 4 times and go to 10096 if Burn In counter is not at zero Bets Note If a Power Off On cycle occurs the Burn in time will be reset to 100 hours Mode Identification IDim Sense LED flash feedback To establish which mak mode is MD n 1 Ensure the iDim Remote is in special function mode l odiset Bano 2 Point the remote at a controller been modified 3 Press Fn key and scene 3 at t
9. nse LED flash feedback To disable the Infra red receiver of a controller ES i Ensure the iDim Remote is in special function mode B Point the remote at a controller l o Press and hold DALI 1 modifier down and Fn key at the same 10s time for 10 seconds Lock iDim Sense Mode Selector Ring IDim Sense LED flash feedback To lock the mode selector ring of an iDim Sense l e 1 Ensure the iDim Remote is in special function mode 2 Point the remote at the iDim Sense you wish to lock l 3 Press and hold DALI 2 modifier up and Fn key at the same time 10s for 10 seconds Note When locked the iDim Sense mode selector ring can still be manually turned However the modes will be ignored unless the mode selector ring is unlocked Unlock iDim Sense Mode Selector Ring IDim Sense LED flash feedback To unlock the mode selector ring of an iDim Sense SES aped Pul cand tel l m5 1 Ensure the iDim Remote is in special function mode 2 Point the remote at the iDim Sense you wish to unlock 2 Press and hold DALI 2 modifier down and Fn key at the same 10s time for 10 seconds Note Dim Sense will remain in the selected mode and in user defined mode where applicable until the mode selector ring is turned again Note All standard operation settings such as scene recall modify and store scene are still possible when the iDim Remote is in special Transfer settings to iDim Sense using iDim Remote function mode OO 0 9 H gt em To
10. transfer settings to iDim Sense using iDim Remote O os ELE e e e ils 2 Point the remote at a controller Press OK and Fn key at same time l S Helvar iDim Remote Control 304 User Manual iDim Sense LED Flash Feedback Two LEDs red and green in the iDim Sense flash to provide visual feedback for various states and operations Mode unmodified User defined mode selected default mode Mode 1 Selected o Classroom mode Mode 2 Selected C C Single Office mode Mode 3 Selected C C C Open Plan mode Mode 4 Selected Co C C C c 99 Geooco9 S Mode 5 Selected C C C Corridor Hold mode Mode 6 Selected C Co C C C C Meeting Room mode PIR Walk Test Mode Sequence repeats until walk test is complete 100 hour Burn In Mode eS 30 seconds e 30 seconds e Sequence repeats until burn in is complete DALI Errors Sequence repeats until error clears Change from unoccupied to occupied Typically follows a PIR detection Data received from IR Remote Enabling Disabling of IR Receiver Failed Scene Store Successful Upload from IR Remote Failed Upload from IR Remote Note iDim Sense LED feedback flashes apply to all iDim units of v5 3 and onwards To leave User Defined mode and reset iDim Sense to default settings at any time hold button 3 4 on the iDim Remote Control for 10 seconds while the remote is in Special function mode See page 6 8 for information Doc No
11. ult iDim modes In this table iDim Controller refers to iDim Remote Switches and Panels unless specified b ie 5 3 S9 4 4 SINGLE OPEN PLAN CORRIDOR CORRIDOR MEETING sni M OFFICE OFFICE LINK HOLD ROOM DALI 1 CL CAL CL DALI 2 Offset Offset Offset pii ue aide corridor below DALI 1 CL CL CL CL DALI 2 Offset Offset Offset w corridor iDim Controller Scene 1 iDim Controller Scene 2 DALI 1 FL 100 FL 100 FL 100 FL 100 iDim Controller es Scene 3 DALI 2 FL 10096 FL 10096 FL 10096 ae corridor DALI 1 FL 40 FL 40 iDim Controller awe Scene 4 DAL 2 aus to FL 20 corridor Note 1 In Corridor Hold iDim Mode 5 DALI 2 is only used to connect an offi ce to the corridor Note2 In Meeting Room iDim Mode 6 iDim Solo SW 1 input operates DALI 1 CL Off and SW2 input operates DALI 2 FL 100 Off as SW is located at the entrance of a room switching off SW1 will cause both DALI 1 and DALI 2 circuits to go off To modify light levels using the iDim remote DALI 1 1 gt 100 Point the remote at a controller Select the scene you wish to modify Press DALI 1 modifier key up to raise DALI 1 light level 100 gt 1 Press DALI 1 modifier key down to lower DALI 1 light level Press DALI 2 modifier key up to raise DALI 2 light level O 01 fF C N Press DALI 2 modifier key down to lower DALI 2 light level DALI 2 1 gt 100 Note 1 If you intend
12. unity EN 6100 6 1 Environment __ Complies with WEEE and RoHS directives 2 Helvar iDim Remote Control 304 User Manual Add Remove Batteries To add or remove batteries 1 Unclip the battery cover on the reverse of the remote 2 Add batteries observing correct polarity and replace cover Batteries not required if running iDim Remote Control through a PC via USB cable Note Assemble iDim Remote Cradle for Desktop Use To assemble the iDim Remote Cradle for desktop use 1 Attach rubber feet A to base B 2 Insert base B into recess C on the reverse of the cradle until it clicks To disassemble the iDim Remote Cradle not shown Insert flat head screwdriver into recess C and gently lever base A away from the cradle to avoid the unit being damaged Setup iDim Remote Cradle for Wall Attachment To mount the iDim Remote Cradle to a wall 1s Drill and insert screw to chosen mounting location Leave approx 1 mm between screw head and wall to allow cradle to sit comfortably on screw 2 Carefully slide the cradle onto the screw adjusting screw tightness as required With cradle still wall mounted mark hole A on the wall Remove cradle drill second hole and apply wall plug Slide cradle back on to wall and insert bottom screw Tighten screw as needed Attach iDim Remote to Cradle To attach the iDim Remote to the remote cradle Ts Place iDim Remote onto cradle mounting point 2 Push iDim Remot
Download Pdf Manuals
Related Search