Service Manual: (A997), RE8, CCDE6, Editor Display, AR-DE80
Contents
1. 100 Full Image Key D The data scanned with 100 dpi is changed to about 33 dpi The entire A3 or DLT original image can be displayed Zoom 1 Key E The data scanned with 100 dpi is changed to 50 dpi 150 enlargement Zoom 2 Key F The data scanned with 100 dpi is changed to about 67 dpi 200 enlargement Zoom 3 Key G The data scanned with 100 dpi is displayed with about 100 dpi 300 enlargement Image Shift Key H Press to shift the image up and down left and right by using the cursor key according to the block diagram displayed at the lower left corner Cursor Key I The cursor on the display will appear at the center after pressing the scan key zoom keys and image shift key The cursor shown on the display will move to the desired position by pressing this key Point Key J Sends the information of the current location of the cursor to the copier Clear Key K The previously marked point before pressing the close key will be canceled Close Key L Press to close an area All Clear Key M All specified dimensions or areas will be canceled O Oo u gt amp o 2 m INSTALLATION 28 December 1993 4 INSTALLATION 4 1 ACCESSORY CHECK Check the accessories according to the following list Description Q ty 1 Key Description Decal ooocconnnccccnnnnocccccnnnonnnccnnnncccnnonnnnnnccnnnnanacnnn 1 A teens 1 32. DISPLAY EDITOR Machine Code A997 28 December 1993 SPECIFICATIONS 1 SPECIFICATIONS Original Size Display Zoom In Out Display Speed Editing Power Consumption Power Source Dimensions W x D x H Weight Remarks Maximum A3 lengthwise or 11 x 17 lengthwise Scanned through the copier LCD Monochrome 8 gradations 640 x 480 dots 100 33 dpi 150 50 dpi 200 67 dpi 300 100 dpi Less than 2 seconds Screen and cursor 19 5W 5V less than 1 5A and 24V less than 10 5 from the copier 280 x 232 x 50 mm 11 0 x 9 14 x 1 97 less than 1 5 Kg or 33 1 Ib The holder is required for installation O Oo u gt amp o 2 m OVERVIEW 28 December 1993 2 OVERVIEW B A K M C D E F G H M NM L The scanned image is sent to the display editor and displayed on the LCD 640 x 480 dot By using the cursor A it is able to designate an area of the original image The display B shows 8 levels of grayscale and the data communication between the display editor and the IPU board is done by 3 bit parallel signal 28 December 1993 EXPLANATION FOR EACH KEY 3 EXPLANATION FOR EACH KEY Key Function Scan Key C Sends the scan start command to the copier and scanning of the original is performed After the scanning the entire original image is shown on the display editor
3. Harness CRAIN ae cet iio 2 A ale ee 4 28 December 1993 INSTALLATION 4 2 INSTALLATION PROCEDURE A C CAUTION When installing the display editor make sure that the copier is unplugged NOTE Holder A702 must be installed before starting the following procedure 1 Remove the front cover A 2 Install the display editor B 4 screws 3 Remove the small cover C a O Mm gt o 2 m INSTALLATION 28 December 1993 F 4 Install the 2 harness clamps D to the lower cover of the optional table 5 Connect the cable E to the connector F of the display editor and to the connector G of the copier 6 Set the cable to the 2 wire cramps 7 Plug in the power cord and turn on the main switch 8 Enable the editor operation by selecting Display in the SP modes page 4 11 No 417 Editor 9 Turn the main switch off and on 10 Stick the key description decal H as necessary 11 Check the machine operation
Download Pdf Manuals
Related Search