Home
OPERATORS MANUAL FOR THE 4000 SPRAYER MONITOR
Contents
1. Actual time Time is adjusted in The actual date The date is adjusted in ENCODE Tegjet 15 TEEJET 4000 OPERATORS MANUAL SPRAY ENCODEMENTS In this menu you must enter the particulars for your Crop Sprayer The particulars you enter vvill be memorised automatically under spray encodements When you have entered a particular figure press the return key to proceed to your next encodements NOTE Check all your figures before you start work Simply check your Status screen Qs gt xI OD Qe gt E DOSERATE Encode your desired application rate in LITRES per HECTARE max figure 9999 L Ha You can alternatively enter alter your rate directly from the operation screen The TeeJet 20D flowmeter most common size Enter flow figure 2000 Guide only Ask your dealer for recommended start figure when using a different size flowmeter DO S AND DON TS DO Check your flow accuracy regularly check against a load DON T Do not calibrate your flow figure against any worked area The computer offers an easy step by step calibration procedure or you may chose to calibr
2. equipment not delivered by the seller Faults that may arise from the buyers negligence to react to varnings and fault messages from the product or which can be traced to negligence and or absent constant control of the work carried out in comparison to the planned job Tua When implementing any new equipment the buyer must take great care and pay attention Any doubts as to correct operation use should result in contacting the seller s service department This manual may not be altered copied or manipulated in any way Unoriginal manuals can lead to operational faults damaging machines or crops as a consequence thereof TeeJet Technologies can therefore not be held responsible for damages incurred which can be traced to the use of unoriginal or manipulated manuals Original manuals can be requisitioned at any time from TeeJet Technologies Kind Regards leejet Technologies Mglhavevej 2 9440 Aabybro Denmark Tel 45 9696 2500 Fax 45 9696 2501 www teejet com TEEJET 4000 OPERATORS MANUAL 6 Tegjet TEEJET 4000 OPERATORS MANUAL GENERAL USE The TeeJet 4000 is specifically designed for crop sprayer control The software design is consequently designed for easy use and access for the operator in conjunction with spray work The computer communicates with you through the screen in clear language Minimum use of this manual is therefore required BEFORE USE It is essential that you ma
3. TEST ber 40 TEST OUTPUT pe CT 41 SPEED SIMULATION e e bag elle Ed 41 SYSTEM DA T cT 41 ERROR MESS AGES 42 VOLTAGE WARNING ad 42 WARNING OUTPUT vo 42 MEMORY FAILURE ed access i 42 MACHINE SETTING CHART 43 NOTES 44 TEEJET 4000 OPERATORS MANUAL INTRODUCTION Congratulations with your new TeeJet 4000 Spray Controller The product is a specifically developed spray controller based on the latest available technology VVe are confident that it vvill serve you to your full satisfaction in the years to come VVe have endeavoured to deliver a fault free product To ensure optimal use of the equipment we ask that great attention be paid when reading the manual Please contact your local dealer if further support is needed Regarding responsibility for use of the product vve refer to our sales and delivery terms especially paragraph 7 which follows 1 Product usage Ke Any use of the product is at the sole risk of the buyer The buyer is therefore not entitled to any form for compensation caused by for example any of the folloving a Disturbance to from any electronic services or products that do not confirm to the standards for CE marking Missing or poor signal coverage or a succession hereof from external transmitters receivers used by the buyer a Functional faults which apply to or from a PC program or PC
4. forward speed detailed below You may use the SIMULATE SPEED e g whilst you set up your sprayer TEST INPUT Test input of all sensors etc TEST OUTPUT Test of all outputs e g power to valve LANGUAGE Select operating language SPEED SIMULATE Speed simulation SYSTEM DATA Non customer accessible info Tegjet 39 TEEJET 4000 OPERATORS MANUAL TEST INPUT Should you observe any malfunction conduct a test of all circuits and sensors vvith the test program The Screen Each text string has a counter shown at the L H side The figure must change each time a pulse signal is received The R H side shows the actual status HI or LO The individual input ports PTO Signal from the PTO sensor WHEEL TRACTOR Signal from the wheel sensor IMPLEMENT Area override signal Tractor TRAIL 1 Signal from pressure sensor if applicable TRAIL 2 Signal from the spray flowmeter TRAIL 4 Signal from wheel sensor on implement if applicable TRAIL 7 Override signal e g pray valve BOOM 1 TO 9 Status of boom sections 40 Tegjet TEEJET 4000 OPERATORS MANUAL TEST OUTPUT OUT1 The power increase output to regulator valve OUT2 The power decrease output to regulator valve OUTS Output to fill
5. not correspond with this reading the spray ET flowmeter may need re pns calibrating CALC VOLUME The required amount is automatically calculated when you press this key START FILL Pressing this key starts recording amount filled and opens the optional fill valve FLOW FIGURE The calibration figure for your Fill flowmeter FILL MODE Select whether a valve is used to stop the flovv VALVE or vvhether a warning is given WARNING Selecting VVARNING gives a visible on screen and audible vvarning Selecting VALVE allows for an electric valve to open shut Tegjet 27 TEEJET 4000 OPERATORS MANUAL FILL FLOVVMETER CALIBRATION NOTE The Fill flowmeter is an independent unit Subsequently it MUST be calibrated individuallyl However as automatic calibration mode is provided by your TeeJet 4000 for the spray flowmeter so it is for your FILL meter The accuracy of the calibration procedure depends on the amount used for calibration The following example uses 1000 litres Please double check the calibration of the fill flowmeter Proceed thus Select FLOW FIGURE through the sub menu Check that a figure is encoded If not enter e g 4000 Press the return key to return to the previous screen Enter a FILL VOLUME Enter approx twice the amount you may require Press the START FILL key in the sub menu Fill the tank with an exact known amount through the fill flowmeter You may us
6. task mode whilst any task is open Should you attempt the screen will display a warning and indicate which task is to be closed Tegjet 25 TEEJET 4000 OPERATORS MANUAL SEE TASK Should you like to verify any task Press SEE TASK Move cursor to desired task Press the SEE key Screen will display the recorded data for that task DELETE TASK Please note that deleted data is irrevocable Move the cursor to the desired task Press the DELETE key NOTE Do delete before you take your notes EXITING TASK MODE Press RETURN until this screen is displayed Press the TASK MODE lower function key symbol Press the END TASK key 26 Tegjet TEEJET 4000 OPERATORS MANUAL TANK FILL FEATURE The HOLD key gives instant access to the Tank Fill features NOTE This is an optional feature that requires specific parts to be fitted to your sprayer Ask your dealer for details FILL VOLUME The amount required to be filled This is calculated through the litre rest Ha rest the tank size and the present application rate FILLED VOLUME The amount measured by the fill flowmeter LITRE LEFT Calculated amount remaining in the tank v NOTE If the actual tank amount ST does
7. the pressure regulator NOTE The shown application rate L Ha is dependent of a correct calibration of wheel circumference flow figure working width Details later in this manual SPRAY BOOM INDICATOR STATUS The number and position of active inactive boom sections is shown on the screen SPEED The forward speed is displayed in km h One decimal NOTE Ensure you select the correct sensor Wheel tractor Wheel sprayer Radar is not available Tegjet 11 TEEJET 4000 OPERATORS MANUAL OPERATOR SELECTABLE FUNCTIONS TRACTOR FUNCTIONS METRE IN TRACK The distance recorded in the current track tramline METRE Recorded total metres METRE START METRE STOP Manual start stop of distance counter BATT Battery voltage METRE IN TRACK The distance recorded in current track You may use this function to locate a position in the track e g the spot where the tank ran empty This function is related to the REDUCE TRA M This function is only visible whilst the sprayer is inactive The METRE IN TRACK counter is reset to NIL each time the sprayer is shut e g at headlands However should you shut the sprayer in a track the computer memorises the distance driven And displays REDUCE TRA M NOTE Should you stop spraying at a position you would like to relocate E g if you need to refill your tank Proceed thus After refilling your tank drive
8. using the Shut Open OV volt key E g Boom section Shut OV States that the wires connected to the boom section switches receive OV ground when the switch is in the OFF position This should be set by the engineer when the system is fitted RPM SENSOR Select weather a RPM sensor is fitted and encode the number of pulses received per revolution NOTE This function is not implemented in all sprayer fitting kits ask your dealer WARNING ENCODE KM H Warning ON OFF and MAX MIN limits for speed warning NOTE Activation of the speed warning provides and ensures minimum spray output when the speed warning is given for the low limit setting E g when the speed falls below that set in KMH warn the spray pressure will be maintained MIS DOSERATE Warning ON OFF and Percent deviation of application rate LITRE LEFT Warning ON OFF for tank level RPM Warning ON OFF and max min limits for RPM Only displayed if RPM ON is selected DATE CLOCK The following can be adjusted HOURS MINUTES YEAR MONTH DAY Tegjet 21 TEEJET 4000 OPERATORS MANUAL SPRAYER DATA DELETE There are 3 main functions in this menu 1 Reading of the total counters Accessible only here Reading the trip counters 2 Deleting all counters by choice Deleting all trip counters simultaneously It is not possible to see select the total counters in the operation menu Subsequently DATA DELETE execution
9. valve if applicable OUT 4 Not used NOTE The SYSTEM test feature comprises of three screens Move to next screen using the NEXT PAGE key NOTE Activation of any in or outputs in the test SYSTEM mode disregards any possible malfunctions you may have provoked through a wrong mistaken encodement Any possible failure caused by defects in the computer software is therefore disregarded SPEED SIMULATION E g whilst testing or calibrating machines it may be desirable to conduct a performance test at a stand still To simulate speed do as follows Put SPEED SIMULATE ON the menu Return to your OPERATION menu Enter the desired speed through the numeric keys How to disable the SIMULATED SPEED Either 1 Move vehicle forward the SIMULATE speed will be cancelled automatically or 2 Encode a simulated speed of 0 nil After 8 sec you can return to SYSTEM for setting SIML SPEED to OFF SYSTEM DATA Information not accessible by the operator Tegjet 41 TEEJET 4000 OPERATORS MANUAL ERROR MESSAGES Your TeeJet 4000 will display various error messages should abnormalities occur VOLTAGE VVARNING Should the power supply drop below 10 V This warning may appear during start or if battery is vveak WARNING OUTPUT Warning of short circuits in the power supply to the regulator valve MEMORY FAILURE Should the computer fail to m
10. F and MIN MAX speed limits DATE CLOCK Adjustment of TIME YEAR MONTH DAY Tegjet 33 TEEJET 4000 OPERATORS MANUAL OTHER IMPLEMENT DATA DELETE There are 3 main options in this menu 1 Reading of total counters only accessible here Reading of trip counters 2 Delete individual counter 3 Delete all trip Counters NOTE The DATA DELETE menu is the only menu available to read and delete the total counters To delete the counters move the cursor to the desired position Press DELETE To delete all Trip counters simultaneously Press DELETE TRIP NOTE Before deleting any records take your notes Deleted recordings are irrevocable Records are TIME Work time since last reset TIME Total work time since last reset HA Worked area since last reset HAr Total vvorked area since last reset METRE Total driven distance since last reset counters accessible only through the DATA DELETE menu 34 Tegjet TEEJET 4000 OPERATORS MANUAL LOG BOOK Your TeeJet 4000 provides a Log Book feature Up to 35 individual jobs can be memorised in the computer This feature and how to work it is detailed on page 23 to 26 in the SPRAYER section NOTE Any job number which you may issue in the Other Implement mode will be transferred whilst you select the Sprayer Mode Please Not
11. OPERATORS MANUAL FOR THE 4000 SPRAYER MONITOR TeeJet No 020 183 UK Version 1 05 lejet Technologies Mglhavevej 2 9440 Aabybro Denmark Tel 45 9696 2500 Fax 45 9696 2501 www teejet com TEEJET 4000 OPERATORS MANUAL 2 Tegjet TEEJET 4000 OPERATORS MANUAL Contents INTRODUCTION e errrnee 5 Ciz zi MU 7 BEFORE U E ngi cr 7 Hells EH ED EET ed de 7 GONTRAST mS 8 e e eos 8 UNS CIBMee om 8 GCGEEAREKEY fM C Pre 8 SCREEN cM 8 NUMERIC KEYS een ete geal ot eon 8 TAE DISPLAY 9 BASIC MENU SOREEDL z n ena ES 9 STATUSF SGREEN derart use ruf cer re Omer creer crater Terie 10 SPRAY PROGRAM T 10 SPRAYER OPERATION eM m 11 PHE DEFINED FUNG TIONS ei idu tu rau ima rata 11 DOSAGE APPLICATION i i 11 SPRAY BOOM INDICATOR STATUS nn 11 SPEED des 11 OPERATOR SELECTABLE FUNCTIONS give bcp Ee ec doct 12 HU euels28se elm T 12 SPRAY FUNCTIONS 13 AREA FUNC bn
12. R 26 SS 26 TANK FICL FEATURE Ps 27 FILL FLOWMETER CALIBRATION aaa eee renen mne 28 OTHER IMPLEMENT aa au s 29 OTHER IMPLEMENT OPERATION eedem iki 30 SELEGTABLE FUNCTIONS ET deb esse 30 TRACTOR FUNCTIONS vc vete eres ee nerne nerne QUEE EUR ne 30 AREA FONCTIONS ana ats 31 TIME FUNCTIONS e rd ird 31 OTHER IMPLEMENT ENCODE iani nando 32 32 WORKING WIDTH TP 32 SPEED SENSOR WHEEL TRACTOR WHEEL IMPLEMENT 33 WHEEL PRAC TOR e e den en 33 WHEEL IMPLEMENT IC nd La t bite Rp EAD EHE 33 SPEED SENSOR CALIBRATION c s zeros 33 IMPLEMENT SENSOR mesin en api EUR adi tas efi 33 METRE SWI c 33 WARNING ENCOD c n P e e ai m 33 DATE GEOG e Te e TT TT 33 OTHER IMPLEMENT DATA DELETE 34 LOGEBOO KE 35 THE LOG BOOK HOW TO USE THIS FACILITY 35 START PRS Nj r n AR E 36 END TASK cc a E E S 37 SEE TAS e ie Eee ae re A aE aG Ta eee arrede lue eee ETRE G 38 DELETE TAS cer re rer tren erat 38 LEAVING TASK MODE ea EET h 38 SYSTEM MEN Urne 39
13. ate manually 16 Tegjet TEEJET 4000 OPERATORS MANUAL STEP Enter your desired percentage figure one entry only for max figure 99 LITRE LEFT To see how much is left in the tank you must encode the amount filled into the tank here If there is an amount remaining in the tank when filling this amount must be added to the amount filled thus Amount remaining in tank amount filled Litre left NOTE If the optional fill flow equipment is fitted LITRE LEFT is encoded automatically HA LEFT As above you must enter the field size before commencing work End time amp required fill amount are calculated from this parameter FLOW FIGURE This is the calibration figure for your flowmeter In other words The measuring accuracy of the liquid You MUST calibrate your flowmeter Recalibrate the flowmeter if the consistency of the liquid used changes FLOW CALIBRATION Encode TeeJet20 D meter a start figure of 2000 Method 1 The computer calibration mode Just follow this instruction and those on the screen 5 6 T Fill the tank or minimum 600 litres Encode the filled quantity in LITRE LEFT and return to Flow figure Spray minimum 500 litres All boom sections open keep within normal pressure range e g 3 Bar You may keep the machine stationary using the simulated speed facility see SYSTEM or select MANUAL and set your pressure see page 14 Verify the remai
14. c pat 15 TIME FUNG TIONS Lm 15 SPRAY ENCODEMENTS tein e 16 DO ER IE dele Ea KEE ske KS aihe 16 DO S AND DON TS PD H 16 STEP c 17 CITRE e P co pena cat 17 iif EEG 17 FEOW FIGURE nguc 17 FLOW CALIBRATION Mec Dc prc 17 BOOM WIDTH m 18 DRIVE PPP 18 REGULATION DELAY garuese 18 UNIFORM PHESSUBE 19 SPEED SENSOR WHEEL TRACTOR WHEEL SPRAY ER 19 WHEEL TRAG LOR c 19 WHEEL SPRAYER cercaire ae endi ordinet 19 SPEED SENSOR CALIBRATION dvd ves dh 19 Ies EN ze n M 20 METRE a ions tabo oe Le bci a Ec or Eas a be b DER 21 INPUT SETS zo 21 RPM SENSOR Pr 21 WARNING ENGODE kueng coed 21 Tegjet TEEJET 4000 OPERATORS MANUAL BDATE GEOGK dq M 21 SPRAYER DATA DELETE boast ctr a e e ra dL aes 22 LOG BOOK f n d EE 23 THE LOG BOOK HOW TO USE THIS 23 SIART TASK j s oe bien h ne ERE 24 END TASK qe C T 25 SEE TASK assis pub URN aed ENC Rena ete bci RADO Ee 26 DELETE TASK as ER
15. ded to one hundredth Above this to one tenth NOTE The DATA DELETE menu provides the Total Area counter NOTE Do not forget to reset your counters using DATA DELETE before you commencing work SELECTABLE FUNCTIONS TRACTOR FUNCTIONS PTO PTO revs requires sensor on the shaft METRE Driven distance in metres METRE START METRE STOP Manual start stop of distance recorder BATT System voltage PTO The revs of the shaft may be other than PTO METRE Driven distance in Metres Is recorded through the speed sensor Can be activated manually or in conjunction with the override sensor Implement Sensor Select the mode in the ENCODE menu or METRE START METRE STOP Manual Start stop of the metre counter These soft keys will only appear if you have selected the manual mode switch BATT The present voltage of your battery 30 Tegjet TEEJET 4000 OPERATORS MANUAL AREA FUNCTIONS HAM VVork efficiency HA Area vvorked HA LEFT Remaining area to vvork HAM HA HA LEFT VVork Efficiency The area cover per hour calculated vvith the present speed and vvorking vvidth Area Counter The vvorked area since last reset May be reset through the DATA DELETE menu where the Area Total counter is also to be found The remaining area to be vvorked Presupposes encodement of the field siz
16. e You cannot escape your operation whilst in task mode if any tasks are open Should you attempt the screen will display a warning and indicate which task to close The functions to manipulate in the Log Book mode are basically START TASK END TASK SEE TASK DELETE TASK THE LOG BOOK HOW TO USE THIS FACILITY Press the key indicated by the arrow The screen shows the mode you have selected In this case the other implement mode indicated by the symbol The two oblong squares shows Tegjet 35 TEEJET 4000 OPERATORS MANUAL The upper 1 one job no is issued oblong is occupied The lower 34 are EMPTY Press START TASK key START TASK You may now use the cursor to select the individual TASK to OPEN The TASK NUMBER you select is your Log Book reference no NOTE Should you select an already open task The trip counter status will remain Consequently Any new recordings will be added on Should you START any EMPTY task The Trip counters are all reset 36 leejet TEEJET 4000 OPERATORS MANUAL Select a TASK The following screen appears STOP TASK SEE TASK DELETE TASK Press the RETURN key to proceed Your select screen app
17. e a weigh bridge for optimal accuracy 7 Select FLOW FIGURE in the sub menu Move cursor to TANK LITRE Encode the amount here 8 Press the flashing CALC FLOW key The flow figure will be calculated and entered automatically gt mmc 28 TEEJET 4000 OPERATORS MANUAL OTHER IMPLEMENT Your TeeJet 4000 may be used in conjunction vvith any type of machine or implement where various monitoring or recording services are required The Other Implement operation of the computer is designed to be similar to the sprayer menus Consequently the major part of this section should already be familiar to you Should you have specific requirements for services not available in the computer please inquire for the upgrade versions available of the TeeJet 5000 computer range Press the RETURN key to return to the MAIN MENU Select OTHER IMPLEMENT Move the Cursor and press SELECT You can now select between the displayed functions The following chapter details the individual functions Tegjet 29 TEEJET 4000 OPERATORS MANUAL OTHER IMPLEMENT OPERATION SPEED The Top information is Speed The speed is read as Kmih to one tenth Speed is calculated vvith the selected sensor VVheel tractor VVheel implement AREA Area is recorded in Hectares The readings up to 99 99 Ha are provi
18. e before vvork commences TIME FUNCTIONS uw TIMER END TIME CLOCK DATE TIMER Work time in Hours amp minutes END TIME Expected finishing time for the current Work CLOCK Actual time DATE Actual Date May be used to record the time used for a particular job Is started stopped manually and can be reset in the DATA DELETE menu Here you also find the Total time counter Expected time of day at which the job will be complete Requires encodement of field size HA LEFT The actual time Can be altered in ENCODE The actual Date Can be altered in ENCODE Tegjet 31 TEEJET 4000 OPERATORS MANUAL OTHER IMPLEMENT ENCODE This menu allovvs for encodements of your TeeJet 4000 in conjunction vvith jobs other than Spray vvork NOTE Encodements in this menu do not interfere with the encodements you may have done in the Sprayer Menu NOTE You must check your encodements through the status screen which will always be shown before you are allowed to enter the operation screen W W W W I I S M 3 Before commencing your vvork you may encode the size of the field From this parameter End Time is calculated WORKING WIDTH The effective work
19. ears now indicating through the shown text TASK NO and the oblong indicating you are in LOG BOOK mode END TASK You can at any time interrupt your present TASK All recordings will be memorised until you delete task Please Note You cannot escape your operation in the task mode whilst any task is open Should you attempt the screen will read a warning and indicate which task is to be closed Tegjet 37 TEEJET 4000 OPERATORS MANUAL SEE TASK Should you like to verify any task No Press SEE TASK Move cursor to desired task Press the SEE key Screen will read the recorded data on that task DELETE TASK NOTE Deleted data is irrevocable Do not delete before you take your notes Move cursor to desired task Press the DELETE key LEAVING TASK MODE Press RETURN to display this screen Press the TASK MODE lower symbol At this screen press the END TASK key 38 Tegjet TEEJET 4000 OPERATORS MANUAL SYSTEM MENU The SYSTEM menu is basically a service feature In the unlikely event of malfunctions this menu provides a comprehensive set of individual TEST facilities However the menu also provides a very useful feature which allows you to SIMULATE
20. emorise data You may overrule this warning by pressing the OK key However check your encodements should this warning appear Should your TeeJet 4000 display errors frequently consult your dealer 42 Tegjet TEEJET 4000 OPERATORS MANUAL MACHINE SETTING CHART Flow figure Sprayer Fill flow Boom Width Boom sections cm S esce d BOD EGA e fee ia e Total Boom Width Drive factor Uniform pressure OS OFF 777 i Wheel Wheel tractor sprayer Boom Main valve Section 43 TEEJET 4000 OPERATORS MANUAL NOTES 44 Tegjet TEEJET 4000 OPERATORS MANUAL Tegjet 45
21. ess the key indicated by the arrow The screen shows the MODE you have selected In this case the sprayer mode indicated by the symbol The two oblong squares shows Tegjet 23 TEEJET 4000 OPERATORS MANUAL The upper 1 one job no is used oblong is occupied The lovver 34 are empty Press the START TASK key START TASK TASK You may now use the cursor to select the individual task to open The Task number you select is your Log Book reference no NOTE Should you select an already used task The trip counter status will remain Consequently Any new recordings are added on All trip counters are reset when any empty task is started Select a TASK The following screen 24 Tegjet TEEJET 4000 OPERATORS MANUAL STOP TASK SEE TASK DELETE TASK Press the RETURN key to proceed The main operating screen appears indicating through the displayed text TASK NO and the oblong indicating you are in LOG BOOK mode END TASK You can at any time interrupt your present TASK All recordings will be memorised until you delete the task Please Note You cannot escape your operation in the
22. ing width of your implement in cm Do not forget the overlap which may cause incorrect measurements 32 Tegjet TEEJET 4000 OPERATORS MANUAL SPEED SENSOR VVHEEL TRACTOR VVHEEL IMPLEMENT Your TeeJet 4000 provides for two differently located speed sensors WHEEL TRACTOR A sensor fitted on the tractor NOTE Possible wheel slippage will interfere with accuracy unless you compensate through with wheel calibration WHEEL IMPLEMENT You may desire to have a permanent sensor fitted on a trailed machine for improved accuracy Whenever applicable speed sensors located on large driven wheels enhances accuracy SPEED SENSOR CALIBRATION The TeeJet 4000 provides an automatic calibration feature for the speed sensor However you may need or desire to calibrate using a manual procedure Both procedures are detailed in the SPRAYER section pages 19 8 20 Calibrate your sensor as described IMPLEMENT SENSOR The implement sensor is the sensor that starts and stops the area meters In OTHER IMPLEMENT you can choose between the following 1 Lift sensor connected via rear of 7 pin socket 2 if a PTO sensor has been mounted 3 Implement sprayer main on off switch starts stops area recordings METRE SWITCH The menu where you decide whether distance recording is controlled manually or in conjunction with the override sensor WARNING ENCODE PTO Warning ON OFF and rev MIN MAX limits KM H Warning ON OF
23. is available only in this menu Set the cursor use the arrow keys to the counter to be deleted Press the DELETE key to erase Should you like to reset ALL TRIP COUNTERS press the DELETE TRIP key NOTE Do not forget to take your notes before deleting The functions are TIME Time counter for consumed time since reset TIME Total operation time since reset HA Area counter Worked area since reset HA Area counter Total area worked since reset Total distance travelled since LITRE Litres consumed since reset Total litres consumed since reset NOTE The total info is accessible only in the DATA DELETE menu 22 Tegjet TEEJET 4000 OPERATORS MANUAL LOG BOOK Your TeeJet 4000 holds a comprehensive LOG BOOK facility A total of 35 jobs tasks can be memorised individually Should you like to use this you must allocate a job No in advance NOTE The trip counters Time Area Litres are all automatically reset when you allocate a new Task no The functions to manipulate in the Log Book mode are basically START TASK END TASK SEE TASK DELETE TASK THE LOG BOOK HOW TO USE THIS FEATURE EE Pressing the lower function key displays the following Pr
24. ities in the computer control mode gt m gt ZA NOTE aware Should you have selected MANUAL mode is the computer unable to resume to control before you reset to AUTOMATIC control mode Pressing the NEXT PAGE key displays the next functions RPM Shaft speed of an axle only displayed if RPM ON is selected in encode TEEJET 4000 OPERATORS MANUAL AREA FUNCTIONS HA LEFT HAM VVork efficiency HA Area vvorked HA LEFT Remaining area VVork efficiency The actual area capacity per hour Area counter The recorded area vvorked since reset of counter May be reset in the DATA DELETE menu This is also where you vvill find the Grand Total Area counter Remaining area to vvork This function requires encodement of actual size of the area in encode HA LEFT TIME FUNCTIONS 25 2 LIZ 3 mi Olm TIMER END TIME CLOCK DATE TIMER Work hours minutes END TIME Expected time of finalisation CLOCK Actual time DATE Day month year Records the vvork time on a specific job You start and stop this recorder manually May be reset in menu DATA DELETE where the Total time recorder is also available Expected time of day at which the job will be complete Requires field size to be entered in encode HA LEFT
25. ke yourself familiar with the keys and their use Please read carefully and study the following pages Unfold the back page which shows the fascia of the computer You communicate with the computer using only 5 keys You will appreciate that the screens relating to the four upper function keys softkeys change as you proceed The screen shows the present significance of each individual key The lower enter return key allows you to return to the previous screen Softkeys Function keys Enter TRACTOR INFO This key instantly displays ACTUAL SPEED VVORK EFFICIENCY AREA VVORKED REMAINING AREA Tegjet TEEJET 4000 OPERATORS MANUAL CONTRAST MEMORY KEY TANK FILL CONTROL CLEAR KEY C 2 SCREEN LIGHT L NUMERIC KEYS 1 9 Adjustment of screen contrast Can be useful vvhen vvorking under dark or sunny conditions NOTE The screen may go dark in extreme hot or cold conditions The display will return to normal when the working temperature of the monitor is back to normal To adjust the screen contrast Use the keys If you want an instant return to any screen press this key before you scroll to another screen The memo key allows for instant return to the memorised screen This key activates the FILL feature which is detailed later in this manual Only active in conjunction with encoding Will erase any incorrectly e
26. mmend that you check the sensor calibration during the season This will ensure of compensation for tyre wear However the design of the TeeJet 4000 makes calibration easy You can calibrate using two methods Automatic or Manual AUTOMATIC SPEED SENSOR CALIBRATION 1 Carefully measure and mark a distance of 100 metres Not on tarmac but field condition soil surface 2 Drive to start position of the 100 m distance and press the CALIB CALC key The screen to the left vvill appear 3 Drive the 100 metre distance Stop exactly at the 100 m mark 4 Anew function key will appear CALC WHEEL Press this key and the computer has automatically calculated and entered the calibration figure Should the flashing WHEEL however not appear the computer has received insufficient pulses from the sensor enabling it to auto calibrate You must calibrate using one of the two manual alternatives Tegjet 19 TEEJET 4000 OPERATORS MANUAL MANUAL SPEED CALIBRATION E g when sensor is fitted to a wheel Mark the wheel e g the valve and mark the field Drive the machine exactly 10 revs of the wheel Mark out on the Field Measure the driven distance carefully to nearest cm Calculate your calibration figure Use the following formula gt m Example The measured distance between marks 52 80 metre 5280 centime
27. moving This is to prevent operator mistakes and incorrect recordings STATUS SCREEN Any time the operation menu is selected or you leave any encode menu the status screen will appear Here all the current encoded values will be shown CHECK amp ACCEPT the values before proceeding by pressing the enter return key NOTE Before start remember to cancel reset all relevant counters Area litre etc using the DATA DELETE function if required SPRAY PROGRAM From the basic menu select sprayer Move cursor to SPRAYER Press SELECT From there you can choose OPERATION ENCODE DATA DELETE LOG BOOK 10 Tegjet TEEJET 4000 OPERATORS MANUAL SPRAYER OPERATION Two Status screens must be accepted Press the Return key until the following screen is displayed Standard functions Display of selectable functions Selectable functions PRE DEFINED FUNCTIONS DOSAGE APPLICATION The primary function under sprayer is dosage The dosage application rate is shown in Litres per Hectare calculated as a result of the flow through the flowmeter the speed and the recorded area Subsequently no reading will show if the machine is stationary or if there is no flow through the flovvmeter Two arrows in the upper left corner of screen indicate the length and status of control signals to
28. ning litres in tank on the tank scale Note machine must be level Place the cursor on TANK LIT and encode the amount remaining in the tank Press the flashing CALC FLOW key The new flow figure is now calculated and automatically encoded NOTE If you should be uncertain regarding the accuracy of the tank scale it is recommended to take the machine to a weigh bridge for verification Tegjet 17 TEEJET 4000 OPERATORS MANUAL Method 2 Manual calibration method Your flovv calibration figure may be calculated as follovvs 1 2 3 NEW FLOVV FIGURE Fill tank vvith minimum 600 Litres Reset your LITRE counter using the DATA DELETE menu Spray minimum 500 litres All boom sections open keep within normal pressure range e g 3 Bar You may keep the machine stationary using the simulated speed facility see SYSTEM or select MANUAL and set your pressure see page 14 Verify the remaining litres in tank on the tank scale Note machine must be level Verify your LITRE recorder reading in the DATA DELETE menu Calculate your correct flow figure using this formula Present flow figure x sprayed amount Litre recorded on computer 2000 x 500 2053 487 The calculated new figure must be encoded in the computer BOOM WIDTH The effective width of your sprayer in cm The TeeJet 4000 computer automatically compensates for open and closed boom sections Conseq
29. ntered figure Switches the back light on and off Only active when encoding values or when simulating forward speed Tegjet TEEJET 4000 OPERATORS MANUAL THE DISPLAY The screen is divided in two sections The upper section is the information screen The lovver relates to the softkeys THE INFO SCREEN You will appreciate the information screen is SYSTEM Info part designed by the manufacturer and cannot be altered by you Bre THE LOWER SOFTKEY FUNCTION Softkeys SCREEN Function keys ve YS The actual significance of the four keys is displayed You will notice that this status changes as you proceed see the following examples m m d 25 gt cS c When powered up the screen will light up and display the main menu Should you have selected an other screen press the return key until the main menu is displayed again SPRAYER OTHER IMPLEMENT SYSTEM The cursor can be moved up amp down using the softkeys Place the cursor on the function you require and press SELECT Tegjet 9 TEEJET 4000 OPERATORS MANUAL IMPORTANTI IMPORTANTI IMPORTANTI The software program does not allow menu changes whilst the machine is
30. ow in Litres per minute through the flowmeter Do not regard this as the Pump capacity Pressing the NEXT PAGE key displays the next functions XX 96 XX 96 NORMAL DOSAGE XX 96 Increase of application rate XX 96 Decrease of application rate DOSE RATE NORMAL Encodement of application rate OR instant return to normal rate 96 activation Percentile increase of the application rate You select the percent figure you require in encode STEP Percent decrease of application rate similar figure will be entered automatically ref the above Multifunctional softkey It will read DOSE RATE normally Select and you will have instant access to enter or alter your desired application rate However should you have activated either your or 96 keys the softkey will read NORMAL Subsequently pressing this key will return your application rate to normal regardless what over under rate you are currently applying Tegjet 13 TEEJET 4000 OPERATORS MANUAL Pressing the NEXT PAGE key displays the next functions Manual increase of pressure application Manual decrease of pressure application AUTOIMAN Select automatic or manual application control keys will appear when you select manual mode This facility may be used e g under severe field conditions where automatic computer control is inefficient or you have observed abnormal
31. to start of track headland border Press REDUCE TRA M and drive along the tramline An audible and visual warning will be given 5 metres before the location at which the tank ran empty VVhen the position is instruction is given to start spraying METRE The total distance driven in metres This is measured vvith the vvheel vvith the speed sensor fitted You may choose manual startistop of counter Or automatically via the override sensor sprayer main valve switch Select your mode in ENCODE METRE SWITCH Or METRE START METRE STOP Manual Start Stop of metre counter The start stop selection screen will only appear if MANUAL has been selected in ENCODE BATT The current voltage of battery 12 Tegjet TEEJET 4000 OPERATORS MANUAL SPRAY FUNCTIONS LITRE LEFT LITRE MIN LITRE Amount consumed from tank LITRE LEFT Amount remaining in tank LITRE MIN Litre consumption per minute The total amount consumed since counter was reset This function is a trip counter which may be reset using the DATA DELETE function The grand total counter is also available in this menu The amount of liquid in tank However this feature requires encoding the tank volume amount filled before starting This is done in encode LITRE LEFT This value is automatically entered is the optional tank fill feature is used The actual fl
32. tre The wheel turned 10 revs Four 4 magnets are fitted 5280 the distance driven in cm 132 000 cm 10 the revs X 4 the magnets This figure 132 is to be encoded Press function key WHEEL TRACTOR Encode 1 3 2 using the numerical keypad Incorrect encodements can be deleted using the C key Manual speed calibration e g sensor fitted to a prop shaft 1 Press the function key CALIB CALC The screen to the left will appear 2 Move drive slowly Stop when NO OF PULSES changes from 0 nil to 1 3 Markthe field 4 Drive slowly Stop when NO OF PULSES changes from 50 to 51 5 Markthe field Measure the distance between the two marks 6 Divide the measured distance cm by 50 Encode the result in cm using the numerical keypad TANK VOLUME The sprayer s tank size is encoded here This is required if the automatic tank fill feature is to be used 20 Tegjet TEEJET 4000 OPERATORS MANUAL METRE SVVITCH Select vvhether distance recording is startedistopped manually MANUAL or by the selected override service sensor e g spray on off switch INPUT SET UP The TeeJet 4000 software allows for a flexible set up of electric connections to ANY TYPE of Crop Sprayer controls Select either MAIN VALVE or BOOM SECTION The screen will read the current status You may change setting by
33. uently each individual spray sections must be encoded into the computer Encode the widths one by one Start with the left hand side section 1 Proceed thus Move cursor to first section Enter width in Cm using the numeric keypad Proceed to section 2 3 etc DRIVE FACTOR The response factor for automatic application control mode This parameter sets the speed of the reaction time of regulation e g Sprayer press regulation valve If the reaction is too slow increase figure or vice versa Min fig 1 500 Normal status Start with 50 REGULATION DELAY Encode the number of seconds that regulation is delayed by after the main valve is opened It is possible to encode from 0 to 9 seconds 18 Tegjet TEEJET 4000 OPERATORS MANUAL UNIFORM PRESSURE Encode vvhether the controls of the sprayer are equipped vvith uniform pressure valves balance return valves or not Yes OFF No If ON remember to adjust your valves SPEED SENSOR WHEEL TRACTOR WHEEL SPRAYER You can chose between two different located speed sensors WHEEL TRACTOR Sensor fitted to the tractor Either externally or an integrated gearbox sensor May apply e g if machine is self propelled type WHEEL SPRAYER Sensor located on the sprayer e g trailed sprayers Calibration of speed sensor Sensors must be calibrated individually SPEED SENSOR CALIBRATION Speed sensor calibration is extremely important We reco
Download Pdf Manuals
Related Search
Related Contents
MS3 Add-On Computer Peripherals (ACP) ADD-GMC-SX-2SC network media converter Manuel d`utilisation Copyright © All rights reserved.
Failed to retrieve file