DMX LED light effect with 5 lenses User manual - Bax
Contents
1. TIC CROSS DMX LED light effect with 5 lenses User manual Safety precautions WARNING This unit may cause serious injury to the eyes when used incorrectly It is therefore strongly advised to read this user manual carefully to get familiance yourself with the functions of this device WARNING This unit must be operated by or under the supervision of an adult This device is not Suitable for children WARNING Do not look directly into the beam from a short distance This may cause serious injury to the eyes Ayra is not responsible for any injuries caused by incorrect use of this device Installation requirements Always check the power supply to which you want to connect the device If the voltage requirements do not meet do not connect the device as this may cause serious damage This device must be installed by a professional technician in a standing or hanging position Only use the included mounting bracket if you want to position the unit against a ceiling or truss system When installed in a hanging position above your audience this unit MUST be secured by using a safety cable capable of holding 10x the weight of this device The unit is designed to be installed with a halfcoupler or G clamp by using the included mounting bracket Direct installation with proper bolts is also possible Make sure there are no flammable objects in the direct environment of the device Do not block the beam exit Keep2. below the power inlet WARNING Before changing the fuse always disconnect the fixture from your wall outlet or any other power supply to prevent electric shocks Always replace a broken fuse with a fuse that has the same type and rating After the fuse has been replaced always close the fuse cover Reconnect the fixture to your power Supply and check whether the problem is solved When this does not solve your problem contact your local dealer for help Spare parts This unit has no user serviceable parts inside When any damage to internal components occur contact your local dealer or a specialized technician in order to repair the fixture Cleaning Clean the housing of the fixture frequently with a damp cloth to remove dust and or dirt WARNING Always disconnect the fixture from your wall outlet or other power supply and let the fixture dry before reconnecting it This prevents possible electrical shocks The lenses can be cleaned with a non aggressive glass cleaning solution but is not recommended Ayra recommends to clean the mirror and lens with a fine brush while removing dust and or dirt with a vacuum cleaner Avoid touching the lenses with your bare fingers to prevent fingerprints on the optics Checkup To prevent dangerous situations make sure your fixture is in optimal condition before using it Check your fixture frequently by using the following checklist All screws must be mounted tightly Check all screws and
3. MX channel mode between 1 and 4 Each mode has its own characteristics which makes basic medium or advanced control possible Working time hour lt is possible to see the total working time of this fixture by activating this feature Test mode test The unit will test all its internal programs Version Vers This feature is only intended for technical purposes and shows the current firmware version of the unit This can not be changed DMX control mode This fixture can be controlled using a DMX controller and standard XLR male to XLR female cable When doing so make sure your DMX controller is capable of controlling your fixture When in doubt contact your local dealer for_advice Set the correct address on the digital display you are able to choose a value between 001 and 255 When a DMX signal is received a blinking red dot on the display is active NOTE At some point mirror motors and lenses will be identified by using the numbers 1 2 3 and 4 The numbers apply from left to right The most left mirror is mirror 1 the most right mirror is mirror 4 This unit has the following DMX channels and DMX values 1 channel DMX mode Channel 1 Pattern _Start value End value Function gt S O O LI Blackout 8 J17 Chase 57 op Chase 86 88 Chase 96 09 Chase 10 4 channel DMX mode Channel 1 Mode selection _Start value End value Function _ gt Z gt O D LH TOR O Channel 2 Chase selection Startva
4. a minimum distance of 0 25 meter from any walls to provide sufficient cooling Make sure the beam exit is not blocked by any objects in the near environment Always use the included power supply Contact your local dealer for a replacement unit if necessary Maintenance and protection Keep the unit away from dusty environments as this may have negative effects on the ventilation and optics Clean the optics with a small soft brush and vacuum cleaner when needed Clean the housing of the unit with a damp cloth WARNING Always disconnect the unit from the power supply when cleaning the unit Reconnect the unit only when any moist on the fixture has evaporated completely Do not switch the power on and off frequently as this may cause serious damage to the unit Avoid heavy shocks and collision during transport and use as this may cause damage to the LED light source electronic circuit optics and housing Keep the device away from moisture rain water or any liquids as this may cause a short circuit and or electric shocks If any liquid enters the unit power supply or housing of the unit disconnect the unit immediately and do not reconnect the power supply Contact your local dealer or technician to inspect the unit for any damage Box contents Box contents 1x TDC Cross fixture 1x power cable Unit and accessory inspection Always use the supplied power cable to connect the unit to a power supply If the cable appears br
5. lue End value Function gt o S a O o 21 E Chase iim TT A A y PG ES CBT RS NE FS Channel 3 Variable speed slow fast Channel 4 Strobe slow fast Installation and maintenance Mounting the bracket A pre mounted hanging bracket is provided with screwknobs at both sides of the fixture This bracket can be used to install the unit to a fixed structure such as a T bar or truss Installing the scanner in a hanging position When you wish to hang the scanner against a wall ceiling or beam make sure to use proper installation tools and let a skilled technician install the scanner for you When you wish to install the scanner to a lighting stand or truss system use a G clamp or halfcoupler for optimal safe and stable fixation Check the technical specifications of your light stand or truss system to gather more information on maximal loads and other safety precautions Transport When using this fixture in mobile setups provide sufficient protection during transport Use the original packaging of this unit or use a professional flightcase with proper foam inlay This way the electronics optics and housing are protected against severe shocks exterior damage and failing electronics Replacing the internal fuse First check whether a failing power supply may be the cause of malfunction When you suspect that the internal fuse is broken the fuse can be replaced by removing the fuse cover located directly
6. male and female Power IEC power connector Included accessories Power cable with Shucko amp IEC connectors 10
7. metal parts for corrosion No visible corrosion may be present The exterior of your fixture must be in optimal condition Check your fixture for dents cracks or missing parts Your installation spot must be in optimal condition Check your installation spot for corrosion cracks dents and strength Electrical components connectors and cables must be in optimal condition Any form of damage cuts exposed wire cores or any other visual deformities should not be present If any visual or mechanical damage is detected contact your local dealer or a specialized technician Do not use a damaged or failing fixture Connectors and wiring schematics DMX connections Electrical wiring DMX output DMX input RENE XLR mounting plug Calle International Brown i 1 Ground vow Blue era N 2 Signal 2 Signal i 3 Signal 3 signal gt YellowGreen oOo Technical specifications LED light effect with 5 lenses Light source 320 LEDs 80 red 80 green 80 blue 40 white 40 amber 1 or 4DMxX channels 3 pin XLR in and output Music controlled mode with internal microphone Microphone sensitivity adjustable through menu Working modes music controlled DMX automatic test master slave Power consumption 40 Watt Fuse T6 3A 250V 20mm glass fast blow Power supply 230V AC 50 Hz Measurements 457 x 433 x 286 mm with bracket Weight 4 kg Connectors DMX 3p XLR
8. oken or has visible damage do not use it If the unit is not going to be used for a longer period of time disconnect it from the power supply and Store it in a dust free environment Always check the unit for possible damage before use If you suspect that something is wrong with the unit do not connect it to a power source When you suspect that your unit is broken or damaged contact your local dealer or a certified technician to inspect the unit When your device does not generate any light do not look directly into the lens When the fixture suddenly produces a beam it may cause injury to your eyes Device overview DISPLAY POWER IN FUSE 100 240V 50 60Hz L r OUT OMX IN Beam output Adjustable bracket IEC Power inlet with integrated fuse holder Control panel display with MENU UP and DOWN buttons Built in microphone for sound active mode DMX input 3P XLR DMX output 3P XLR NOOO PR Go MM Setting up the unit To activate the unit connect the included power supply with the unit and a suitable 230V 50 Hz power outlet The unit will activate directly after it is plugged in to a wall outlet or other power source The status of the fixture is shown on the display Certain values determine the current status and will change when you push buttons on the control panel The buttons each have their own function for easy navigation in the control panel When connecting the unit for the fir
9. st time Press the MENU button to switch modes so you can easily select the built in master slave music controlled or DMX mode Press Enter to confirm a setting Display codes DMX Mode Addr 1 This value represents the DMX channel where the scanner is currently set to 1 stands for channel 1 but can be changed with the UP and DOWN buttons to a value from 1 to 255 When receiving DMX data a small red dot on the display will blink continuously regardless of what function is being used Music controlled mode Soun When oo DMx signal is detected in DMX mode or when you select the master mode the unit will turn itself into music controlled mode displaying Soun Use the microphone sensitivity potentiometer to adjust the sensitivity of the internal microphone for optimal light to sound functionality When no music is detected the scanner will play a slow automatic program until a beat or loud sound is detected The Sound mode can be activated or de activated Master Slave mode Nast SL 1 SL 2 The Nast value stands for the master unit which will use the internal microphone to perform music controlled This fixture will send out a signal for slave fixtures which you may connect using standard XLR male to XLR female cables not included The slave units show SL 1 or SL 2 on the display This way you can select a synchronous or horizontal mirrored slave function for more dynamic effects S
10. tand alone mode Shnd This mode uses the internal programs of the unit to perform a stand alone light show The TDC Cross has 13 built in programs varying from 0 to 12 When the internal microphone is active the unit will change the beam output on every detected beat When there is no music detected the unit will provide a steady and slow change of patterns When the internal microphone is not active the unit will play the programs on a predefined speed Microphone sensitivity Sens The microphone sensitivity is digitally adjustable between 0 and 100 0 is a very low sensitivity 100 is a very high sensitivity Feel free to adjust this sensitivity until you have reached the optimal setting LED display mode Led The LED display of the unit can be turned off during use which makes your light show more attractive especially if the display is visible for your audience When using the menu buttons the display will be lit but after several seconds inactivity the display will be turned off When pressing one of the menu buttons the display will activate itself again The off value means display OFF the on value means display ON The DMX indicating dot will not turn off for convenience reasons Flip display Disp When activating this function the LED display will flip upside down This might be convenient when the fixture is installed in a certain way and you need to read the values on the display Channel mode Chnd This mode changes the D
Download Pdf Manuals
Related Search