Whity 1 Zoom series USER MANUAL
Contents
1. White led s Third channel Strobe Fourth channel Zoom DMX start address setting This device has a maximum of 4 DMX channels in mode 2 If you set for example the DMX start address to channel 1 the device will use the channels 1st to 4th channel for control The first available channel for the next fixture will be the 5 DMX adress Please be sure that you do not have any overlapping channels in order to control each device correctly and independently from any other fixture on the DMX chain GLG Lighting products 7 If two three or more devices are addressed similarly they will work similarly Press the Menu button Press the Up Down button until it shows AXXX in the display XXX is the address you set last time Press Enter button Press Up Down button to select your desired address e g A001 Press Enter button to save or press Menu button to exit Pirin ld MILILI MENU ENTER UP DOWN t y Factory default setting Press the Menu button Press the Up Down button until it shows Reset in the display Press the ENTER button It will reset all functions The spot will go to mode 2 with start address A001 Master slave operation More devices can work syncronizely when there is no DMX signal input For Master slave operation you need to use one device as the master The master device can be any one in a DMX Master slave chain CLEANING AND MAINTENANCE DANGER TO LIFE Disconne2. Whity 1 Zoom series USER MANUAL CAUTION Keep this device a way from r ainand moisture Unplug mains lead before op ening the h ousing For your own safety please read this user manual carefully be fore your initially start up Every person involved with the installation operation and maintenance of this device has to be qualified follow the instructions of this manual consider this manual to be part of the total product keep this manual for the entire service life of the product pass this manual on to every further owner or user of the product include every supplementary update with the original manual Before your initial start up please make sure that there is no damage caused during shipment Should there be any do not use the device and consult your supplier SAFETY INSTRUCTIONS This device has left our premises in absolutely perfect condition In order to maintain this condition and to ensure a safe operation it is absolutely necessary for the user to follow the safety instructions and warning notes written in this user manual Important Damages caused by the disregard of this user manual are not subject to warranty The dealer will not accept liability for any resulting defects or problems Always plug in the power unit least Keep away from heaters and other heating sources Keep away children and amateurs from the device Never leave the device running unattended If the device has been e
3. ct from mains befo re starting maintenance operation The operator has to make sure that safety relating and machine technical installation are inspected by an expert after every four years in the course of an acceptance test a skilled person once a year 1 All screws used for installing the devices or parts have to be tightly connected and must not be GLG Lighting products 8 corroded 2 There must not be any deformations on the housing fixations and installation spots ceiling suspension trussing etc 3 The electric power supply cables must not show any damages material fatigue e g porous cables or sediments Furthur instructions depending on the installation spot and usage have to be adhered by a skilled installer and any safety problems have to be removed The interior of the device need to be cleaned at least annually by an air jet or a vacuum cleaner There are no serviceable parts inside the device except for the lamp and fuse Maintenance and service operation can be only carried by authorized dealers Should you need any spare parts please use genuine parts Should you have further questions please contact GLG TECHNICAL SPECIFICATIONS Power supply AC 200 250V 50Hz Power consumption 130W LED quantity 36x3W WW leds Service life Exceed 30 000 hours Working mode Manuel setting DMX 512 control 4 channels maximum Dimmension 230x230x330mm Cart
4. e the first slave device with the DMX input of the third device the second slave device Always connect one output with the input of the next device until all devices are connected Caution At the last fixture the DMX cable has to be terminated with a terminator Solder a 120 Q resistor between Signal and Signal into a 3 pin XLR plug and plug it in the DMX output of the last fixture 120 Q a PIN 1 PIN 3 PIN 2 GLG Lighting products 5 4 Control panel and display The control panel on the device allows you to control the device including DMX start address setting Automatic operation setting Manuel dimmer Rainbow effect setup etc Display window The device use a 4 digits red color LED display module for displaying your setting The module can display some simple letters and figures Buttons for setup MENU button Prepare to select the menu or exit without saving UP DOWN Select the menu or select your desired value ENTER SAVE Enter main menu Save your selected value Menu extension The LED display allows you to extend or abbriviate the menu Press the Menu button Press the Up or Down buttons until it shows Menv in the display Press Enter button to enter setting Press the Up or Down buttons to select on or oFF Then press the Enter button to save or press the Menu button to exit If you select on then the menu is complete If you select oFF then the menu is
5. idden due to safety reasons If this device will be operated in any way different to the one described in this manual it may suffer damages and the guarantee becomes void Furthermore any other operation may lead to dangers like short circuit burns electric shock etc GLG Lighting products 2 REAR PANEL e 6 L DMX INPUT DMX OUTPUT 8888 MENU ENTER UP DOWN POWER IN 0000 CONTROL PANEL 1 LED DISPLAY 2 MENU BUTTON 3 ENTER BUTTON 4 UP BUTTON 5 DOWN BUTTON GLG Lighting products 3 SETUP 1 Rigging the device DANGER OF FIRE Make sure there is no inflammable material nearby during installing Follow the instructions stated on the bottom of the base of this device WARNING Use 2 clamps to rig the fixture onto atruss Make sureit is fixed properly Ensure the structure truss issecure This device can be installed directly onto a truss wall or stage floor in any orientation without altering its operation characteristics Use proper bolts to mount the device via its brackets The brackets should be attached to the device with proper bolts Always use a secondary safety rope that can hold at least 10 times the weight of the device The minimum distance between the device and illuminated surface is 1 meter There should not be any flammable materials 10 meters around the device 2 Connection to mains Connect the device to mains with the enclosed powe
6. incomplete The display will only show the AXXX for DMX control mode and Menu for Menu extention MEAG loft on MENU ENTER UP DOWN MENU ENTER UP DOWN MENU ENTER UP DOWN Complete Main Menu Press The Menu button then press Up or Down button the display will show below 1 AXXX This is the DMX starting address See page 7 2 Menu This is the Menu extension setting See above GLG Lighting products 6 3 ModX This is the mode setting of the spot See page 7 4 C1 This is manual dimmer of the 1 color white 5 Reset xxx This is the loading of the factory default settings OPERATION Manual operation Press the Menu button Press Up Down button until it shows C1 in the display C1 means White led s Press Enter button Press the Enter button the last 2 digits in the display will show C1 12 This is the level of the manual dimmer Press Enter button to save or press Menu button to exit Also there is the option in the menu to manually set the zoom in steps from 1 12 from wide to near DMX operation The DGM Kameleon series gives you the possibility to set the spot in different user modes When you connect a DMX signal to the spots the display will indicate this with a dot on the display Mode 1 3 channels First channel is the master dimmer 14 bit dimming Second channel is white led s Third channel is zoom Mode 2 4 channels First channel Master dimmer 14 bit dimming Second channel
7. on size 240x240x340mm Net weight 4 kgs Gross weight 5 5kgs Please note Every information is subject to change without prior notice GLG is a trademark from GOED LichtenGeluid The Netherlands www goedlichtengeluid nl GLG Lighting products 9
8. r plug The occupation of the connection cables is as below Cable color Pin Internation code Brown Live L Blue Neutral N Yellow Green Earth an The earth has to be connected 3 Master slave DMX 512 connection The wires must notcome into contact with each other otherwise the fixture s will not work at all or will not work properly Only use a stereo shielded cable and 3 pin XLR plugs and connectors in order to connect the GLG Lighting products 4 controller with the fixture or one fixture with another Occupation of the XLR connection DMX input 1 Ground y DMX output XLR mounting 1 2 2 Data 2 j1 XLR mounting socket 3 Data id socket If you are using controllers with this occupation you can connect the DMX output of The controller directly with the DMX input of the 1st device in the DMX chain If you wish to connect DMX controllers with other XLR outputs you need to use adapter cables 1 Ground DMX input KO N 2 Data _ DMX output XLR mounting 9 3 Data S 1 XLR mounting socket 2 SA 4 no use Frs socket 5 no use Building a serial Master slave DMX chain For Master slave connection you need to set a device as the Master device All other devices will be the slave devices Connect the DMX output of the first device Master in the chain with the DMX input of the second device the first slave device Connect the DMX output of the second devic
9. xposed to drastic temperature fluctuation e g after transportation do not switch it on immediately The arising condensation water might damage your device Leave the device switched off until it has reached room temperature Always disconnect from the mains when the device is not in use or before cleaning it GLG Lighting products 1 There are no serviceable parts inside the device Maintenance and service operations are only to be carried out by authorized dealers Please note that damages caused by manual modifications on the device or unauthorized operation by unqualified persons are not subject to warranty OPERATING DETERMINATIONS This device is an LED lighting for color decoration in discotheques on stages etc It is allowed to be operated with an AC of 200 250 V and is designed for indoor use only Do not shake the device Avoid brute force when installing or operating When choosing the installation spot please make sure that the device is not exposed to extreme heat moisture or dust There should not be any cables lying around You endanger your own and the safety of others Operate the device only after having familiarized with its functions Do not permit operation by persons not qualified for operating the device Most damages are the result of unprofessional operation Please use the original packaging if the device is to be transported Please consider that unauthorized modifications on the device are forb
Download Pdf Manuals
Related Search