Operating Instructions Tumble dryer
Contents
1. Outer casing material Setup Drain Standard tests Europe Drying performance Energy declaration 850mm 595mm 585mm 47kg 1111 7kg 52 rpm See type plate Stainless steel Powder coated and hot galvanized sheet steel or stainless steel Stacking or freestanding 1 7m polypropylene hose 3 4 BSP connection EN 611 21 95 13 EEC Auto normal dry 7kg cotton EN 611 21 95 13 EEC Auto normal dry 7kg cotton Test method for noise measurement IEC 60 704 2 6 Service Before contacting the service division Before contacting the service division you should find out whether you can resolve the fault yourself See the Troubleshooting and Care and cleaning chapters If you still need to contact the service division make sure that you know the model designation type designation and serial number The model designation can be found in the stamped hole on the first page of the operating instructions and on the machine s panel The type designation and serial number can be found on the type plate Model designation Type plate 17 18 Installation Positioning the tumble dryer The tumble dryer can be free standing or ina stack Remember that the tumble dryer produces heat and should therefore not be located in a room that is too small If the room is very small drying will take longer d2. Dry fabrics of the same type together to ensure that they dry as evenly as possible 2 Turn on the main power switch e Close the door 3 Load the garments Art No 80 901 10 Rev 01 We reserve the right to make changes Select a programme and any options e Turn the programme selector to the required programme e Select any options and settings 5 Press the Start button Drying programme finished e END appears on the display when the programme is finished e Clean the lint filter after each load Once drying has finished e Turn off the mains power switch and close the door CE Printed on environmentally friendly paper that meets the requirements of Mllj6f rbundet and Naturskyddsf reningen
3. Overheating cut out Drying takes too long The washing does not dry or is too dry Error messages Technical information Technical data Standard tests Service Before contacting the service division Installation Positioning the tumble dryer Adjusting the feet Air evacuation Electrical installation Door hanging Follow these instructions Quick guide Fabrics Turn on the main power switch Load the garments Select a programme and any options Press the Start button Drying programme finished Once drying has finished 14 14 14 15 15 15 15 15 15 16 16 16 17 17 18 18 19 19 21 22 23 24 24 24 24 24 24 24 24 Before using your machine for the first time Do not tumble dry Certain materials are not suitable for tumble drying Always check and follow the instructions on each item s laundry label You can find more information in the chapter Advice and tips before you tumble dry Note When starting the tumble dryer for the first time or after a long period without use you may notice a slight thumping noise This noise is completely normal and will disappear after a few loads See the Quick guide on the last page Safety instructions Read the operating instructions and keep them in a safe place e Electrical installation if required should be carried out by a qualified electrician e The machine should only be used for tumble drying as described in these instructions e Repairs
4. be tumble dried because of the risk of felting Static electricity To reduce the risk of static electricity in the laundry after tumble drying you can e Use fabric softener when washing e Wait five minutes after the drying program ends before opening the door and removing the laundry from the dryer Note If the door is opened during the programme the programme will be interrupted and will return to the start The clothes may be too damp or too dry as a result 10 Tumble drying Below are step by step instructions to help you achieve the best possible tumble drying results Sort your fabrics You will achieve the most uniform drying results if the items are made of the same type of material Do up zips and buttons fasten belts sort the items and adjust the load and temperature Turn on the main power switch Open the door load the items 3 and then close the door A the programme Guidelines as to what specific programmes can be used for The Auto extra dry Auto dry and Auto normal dry programmes have two temperature settings Normal temperature but also low temperature for more delicate items Auto extra dry This programme is for items that are particularly difficult to dry e g jeans with very thick seams Auto dry These programmes shut off the heat once the load is dry but before itis over dry The Auto dry programme shuts off the heat slightly later than Auto normal dry Use trial and
5. filter If the display reads Insert filter the tumble dryer will not start Insert the lint filter in its holder The lint filter must be cleaned after each load If you have very hard water this can cause limescale deposits in the lint filter Check for any limescale deposits when cleaning the lint filter and if necessary wash the filter by hand 1 Grasp the filter handle and pull it towards you 2 Pull the filter out of its holder 3 Open the filter and remove the lint from all sides of it by hand Use a soft dry cloth to remove any deposits 4 Replace the filter in its holder Note If you have hard water the filter should be washed with water to get rid of any limescale deposits Use a sponge and alittle dishwashing detergent if necessary Dry the filter carefully with a towel If you cannot remove the limescale you can buy a new filter from the retailer where you bought the tumble dryer Cleaning the outside of the machine Clean the outside of the machine and the programme panel with a mild cleaner Do not use solvents as these can damage the machine Do not hose down or spray the machine with water Note Do not allow dust to accumulate around the machine Keep the area around the tumble dryer clean and cool dust heat and moisture prolong drying times Troubleshooting The machine will not start Check e that the door is properly closed e that the main power switch is on e that
6. ool ol oN ol oo ol Kolo 5 Outer door Main power switch 2 Panel 1 6 Fan behind hatch 7 Lint filter 3 Type plate 4 Lint filter holder Front panel 1 Main power switch 2 Programme selector 3 Display window aw 4 Start 5 Stop lt 4 Ol Advice and tips before you tumble dry Here are some tips that may help you before you begin tumble drying Have the clothes been spun Items to be tumble dried should be spun at 1000 rpm or faster Higher spin speeds save both energy and drying time Materials that can be tumble dried This symbol means that the material is suitable for tumble drying Fabrics best suited to tumble drying are cotton fabrics terry cloth and synthetic fibres Garments will be softer and lighter when tumbled than when hung out to dry Note The tumble dryer does not cause any significant wear to fabrics The lint that is trapped in the lint filter consists of dust and fibre residues which form when the items are used Materials that must not be tumble dried Kl this symbol means that the material is not suitable for tumble drying Certain materials may melt or become a fire hazard if exposed to heat and others can lose their shape or shrink And do not tumble dry e materials labelled Do not dry near heat e garments that have been dry cleaned at home e plastic foam e fibreglass material e wool must not
7. the plug is connected e that the fuses circuit breakers in your house are intact Swap two circuit breakers over to make sure You cannot always tell from the outside if a circuit breaker is broken e thatthe overheating cut out has not been triggered see below e that the lint filter is in place and is clean Overheating cut out The overheating cut out shuts off the tumble dryer if the temperature is too high e g because dust is clogging the lint filter e Clean the lint filter e The overheating cut out will reset automatically once the machine has cooled down Drying takes too long e Check that the lint filter is not clogged see the Care and cleaning chapter The washing does not dry or is too dry e The door has been opened while the programme is running which disrupts the moisture monitoring function Error messages e If Max program time appears on the display the maximum programme time has been reached Read Drying takes too long in the Troubleshooting chapter to find out what to do e If Clean lint filter appears on the display clean the lint filter e Press the Stop button to close error messages e The tumble dryer cannot start if the lint filter is not in place The error message Insert filter appears on the display 15 Technical information Technical data Height Width Depth Weight Cylinder volume Max drying capacity Speed Rated power Drum material
8. Operating Instructions Tumble dryer Imesa ES7PEE Dear Imesa customer Welcome to the family of Imesa customers We hope that you will have many years of use from your new machine The machine has many special functions To ensure that you get the most out of these functions we recommend that you read the operating instructions before using the machine The operating instructions contain information on how to avoid damaging the environment oImMmESA Contents Before using your machine for the first time Do not tumble dry Safety instructions Installation Safety Interrupting a programme Packing material Recycling Child safety General Activating deactivating Child safe start Description of the tumble dryer Front panel Advice and tips before you tumble dry Have the clothes been spun Materials that can be tumble dried Materials that must not be tumble dried Static electricity Tumble drying Sort your fabrics Turn on the main power switch Open the door load the items and then close the door Select the programme Press the Start button Drying programme finished Once drying has finished Settings How to choose the settings Language Child safe Audible Volume Element 2 OounKR KA RAR RWW oN OD co 10 10 10 10 10 12 12 12 13 13 13 13 13 13 Care and cleaning Cleaning the lint filter Cleaning the outside of the machine Troubleshooting The machine will not start
9. and maintenance relating to safety or performance must be carried out by a qualified professional e Damaged mains cables must only be replaced by a qualified electrician e Sufficient ventilation is required to prevent smoke from open fires or fumes from equipment burning other fuels being sucked into the room when the tumble dryer is running e Do not dry dirty laundry in the tumble dryer e Items that are stained with e g cooking oil acetone alcohol petrol kerosene stain remover turpentine wax and wax remover should be washed in hot water with extra detergent before they go in the tumbler dryer e Items such as foam rubber latex plastic waterproof textiles rubber coated items and clothes and foam rubber filled cushions must not be dried in the tumbler dryer e Fabric softener or similar products should be used as per the recommendations of the detergent manufacturer e The machine is not designed to be used by persons even children that are physically or mentally handicapped or lack experience and knowledge Such persons must receive instruction in how to use the machine from the person responsible for their safety e Children must be watched to ensure they do not play with the machine e Do not let lint accumulate near the dryer e Do notinstall the dryer behind doors with lock sliding doors or next to the doors with hinges so that opening of the dryer door will never be hindered Caution A Never stop a tumbl
10. door is closed if a child pulls the door shut from the inside for example In order to prevent children from starting a programme or changing one that has already started you can activate the Child safe Start option Activating deactivating Child safe start Do as follows to open the settings menu 1 Turn off the machine using the main power switch 2 Press the Stopbutton and switch on the machine with the main power switch Then press the Stopbutton 5 times within 10 seconds 3 Select the setting you want to change by turning the programme selector 4 Press the Stopbutton once 5 Change and save the setting as described below 6 Press Start to return to the programme menu You can activate the Child safe start option to prevent children from starting the machine 1 Turn the programme selector and choose Child safe start on or Child safe start off 2 Press the Stopbutton once to save the setting You can temporarily deactivate Child safe start by pressing Start and Stop at the same time Child safe start will be deactivated for 3 minutes Description of the tumble dryer 0000000000000000 00000000000000 000 000000000000000 00 00000000000000 000 000000000000000 00 000000000000000 00 0000000000000000 0 P0000000 000000000 O0000000000000000 0000000000000000 0 00000000000000 000 O00000 00000000000 00000000000000 000 00000000000000 000 O00000 0000000000 lool ol ool
11. dryer is correctly positioned on the washing machine Break off tag A on the cup fitted on the right hand side and tag B on the cup fitted on the left hand side Then remove the paper from the self adhesive surface under the plastic cups a a B Installation 5 Fit the plastic cups so that the tags marked with arrows are against the front edge or side edge of the cover and press them firmly onto the cover Then break off the remaining tags 27 6 Push out the knock out hole on the back of the dryer you must not remove it just open it using a hammer and screwdriver 7 Push the tumble dryer in under the metal brackets Atthe same time keep the front edge raised by 10mm to 20mm a a L 8 Lower the tumble dryer s front feet into the plastic cups and adjust the dryer to ensure that it is balanced Adjusting the feet Screw the feet in or out so that the tumble dryer is steady and balanced on the floor or on the washing machine Then tighten the lock nuts Air evacuation Waste air from the tumble dryer must be taken to an evacuation duct or to an outlet in the wall using the vent hose supplied Connection to the tumble dryer The tumble dryer has three options for venting air at the back on the right side and on the left side One hole is open when the tumble dryer is supplied The other two have covers The tumble dryer comes with a connector 1 a plastic band 2 and a vent h
12. e dryer before the programme is completed unless you immediately remove all the laundry and spread it out so that the heat can disperse Installation See the Installation chapter Safety e The machine must not be used for drying items that have been dry cleaned at home or fabrics that may contain residues of flammable liquids e The tumble dryer is protected by an overheating cut out This shuts off the machine if the temperature gets too high Caution A When the tumble dryer is operating the back of the tumble dryer will get very hot Leave the machine to cool completely before touching the back Interrupting a programme You can stop a drying programme by e Open the door The drum will then then stop automatically e Press the main power switch e Press the Stop button for three seconds When you want to resume tumble drying simply close the door and press the Start button Packing material Please sort waste materials in accordance with local guidelines Safety instructions Recycling This machine is manufactured and labelled for recycling In order to prevent injuries the machine must be made unusable once the decision has been taken to dispose of it Contact your local authority for information about where and how your machine can be recycled correctly Child safety General Do not allow children to play with the tumble dryer A The tumble dryer does not start automatically when the
13. error to find out what works best Use these programmes when you want items to be completely dry Auto normal dry These programmes shut off the heat once the load is dry but before itis over dry The Auto dry programme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best Use these programmes when you want items to be completely dry Auto extra dry fe low temperature This programme is for items that are particularly difficult to dry e g jeans with very thick seams Auto dry fe low temperature These programmes shut off the heat once the load is dry but before itis over dry The Auto dry programme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best Use these programmes when you want items to be completely dry Auto normal dry fe low temperature These programmes shut off the heat once the load is dry but before it is over dry The Auto dry programme shuts off the heat slightly later than Auto normal dry Use trial and error to find out what works best Use these programmes when you want items to be completely dry Auto iron dry This programme shuts off the heat once the load is just damp enough for ironing or pressing Tumble drying Programme chart Here we present a few examples of the energy and time consumption of a few different programme settings Consumption can vary according to room temperature hu
14. midity load variations in the power supply and selected options For the consumption values given below the requirements are as follows Temperature of intake air 23 C Moisture content of intake air 55 Drying temperature Normal or low Heater output 3000W Programme chart Program Material Temper Max load kg Energy consumption Programme time ature approx kWh approx hrs and min 800 rpm 1600 rpm 800 rpm 1600 rpm Auto extra dry Cotton linen Normal 7 0 4 4 4 1 2 01 1 55 Auto dry Cotton linen Normal 7 0 4 1 3 8 1 51 1 45 Auto normal dry Cotton linen Normal 7 0 3 5 3 4 1 31 1 30 Re Low 2 3 1 53 Auto extra dry low temperature R A Crease resistant Low 3 5 2 0 1 28 Auto dryf low temper Polyester cotton ature P Crease resistant Low 3 5 1 8 1 23 Auto normal nh low polyester cotton temperature Auto iron dry Cotton linen Normal 7 0 3 1 2 8 1 48 1 45 This programme is EN 61121 compliant Energy and time consumption in compliance with EN 61121 12 Tumble drying Press the Start button Remaining drying time An estimate of the remaining drying time will be shown on the display a few minutes after the drying programme starts For example 1 35 means that it will take approximately 1 hour and 35 minutes for the load to dry The actual remaining time may be longer than the estimated time shown on the display The remaining time is then sh
15. on the upper and lower edges 22 Door hanging You can choose whether the door is hung on the right or the left Follow these instructions 1 Remove the plinth 2 Remove the hinge two screws 3 Lift the door up and remove it Support the door at the same time 4 Remove both door pins top and bottom Fit them on the other side of the machine Refit the hinge 5 Loosen the screws 13 in total on the inside of the door 6 Loosen the inner part of the door pull down and lift out 7 Switch the catch magnetic lock and the cover plate First loosen the screw holding the catch magnetic lock in place Then use a flat bladed screwdriver to remove the cover plate Refit the catch magnetic lock and the cover plate on the other side 8 Reattach the inner part of the door with the screws 13 in total 9 Move the plastic plugs on the upper and lower edges of the door Use a flat bladed screwdriver to remove the plugs 10 Loosen the two screws holding the handle in place on the door Push out the two plastic plugs inside the screw holes on the other side of the door Use the two screws to attach the handle to the other side of the door and press the plastic plugs into the holes where the handle was previously fitted 11 Refit the door by loosening the hinge screws slightly affixing the door and closing it Retighten the hinges Replace the plinth 23 24 Quick guide Fabrics e
16. ose 3 Fit the air evacuation system as follows 1 Slip the vent hose onto the connector and secure it using the plastic band 2 Remove the plastic cover if you want to fit the vent hose to one of the holes other than the one already open 3 Insert the connector with the vent hose into the opening 4 Place the cover over the open hole 19 20 Installation Connection to the evacuation duct The vent hose must take the shortest and straightest route possible from the tumble dryer to the evacuation duct Trim or cut the vent hose if itis too long If necessary the vent hose can be extended to a maximum of 8 metres inner diameter 102 mm If a longer hose is needed a larger inner diameter is required in order to maintain the tumble dryer s fan capacity Any bends must be as gradual as possible If 90 bends are necessary there must be no more than four More bends will reduce the tumble dryer s fan capacity a Examples of installations Caution Air from the tumble dryer must not be fed through ducts used for equipment that burns gas or other fuels Installation in a hot environment If you install the tumble dryer in a small room with a high atmospheric humidity where the temperature may exceed 25 C there is a risk of condensation accumulating in a kink and obstructing the air flow resulting in poor drying results To avoid this happening
17. own as 0 15 until the load is sufficiently dry Stopping or changing a programme Press and hold button the Stop button for three seconds Note The programme will not be affected if you change the programme selector after the programme has started Loading or removing washing You can stop the tumble dryer after starting a programme by opening the door Load more washing or take out the items you want close the door and press the Start button A new estimate of the remaining programme time will be displayed after a few minutes Drying programme finished 6 The text End appears on the display when the programme is finished Backlighting Two minutes after the drying programme finishes the backlighting on the display and option buttons enters energy saving mode Important e Clean the lint filter after each load Caution A If the lint filter becomes clogged the machine s automatic overheating cut out may be triggered In order to be able to restart the machine you must clean the filter and allow the machine to cool down for around 30 minutes Once drying has finished Turn off the main power switch Remove the clothes and close the door to prevent small children from climbing into the machine Settings How to choose the settings e Language e Child safe e Audible Volume e Element 2 Do as follows to open the settings menu 1 Turn off the machine using the main power switch 2 Press the Stopb
18. the hose must not be fitted so that it goes up a but instead so that it is horizontal b or goes down c from the drier Installation Accessories If the vent hose runs to an outlet in the wall you can prevent the inflow of cold air by fitting a ventilation grill This grill can be installed either outside or inside If there is only one evacuation duct from the room a draught check must be fitted Draught check These accessories can be purchased from your retailer Electrical installation The electrical connection must be made using a cable for permanent installation with a multipolar circuit breaker by a qualified professional Connection on delivery The machine is supplied as 1 Phase 230V 50Hz heat output 3000W and has a 16A plug Any residual current devices must be type A 21 0000000000000000 000000000000000 00 0000000000000000 0 000000000000000 00 0000000000000000 0 o0o0000000000000000 0000000000000000 0 0000000000000000 0 0o0000000000000000 0000000000000000 0 0000000000000000 0 0000000000000000 0 0000000000000000 0 0000000000000000 0 0000000000000000 0000000000000000 Door hanging Locking hook 4 Hinge pins top and bottom 2 Cover washer 1 Hinges left right side Plinth 5 6 3 Plastic plugs
19. ue to the limited quantity of air Caution A e Any electrical installation must be carried out by qualified professionals The machine must not be installed behind a lockable door a sliding door or a door with hinges on the opposite side to those of the tumble dryer The tumble dryer s plinth ventilation must not be blocked by a rug or the like Tip To improve ventilation leave the door to the room where the tumble dryer is located open Freestanding The tumble dryer can be positioned beside the washing machine An air gap of at least 5 mm must be left between the washing machine and the tumble dryer Stacking The tumble dryer can be placed on top of a Imesa washing machine In this case you use the stacking attachments foot cups and anti tilt devices that come with the machine You will find two foot cups in a bag in the drum and two anti tilt devices are attached to the bottom left corner at the back of the machine Extending plates can be ordered from your local retailer How to assemble the stack 1 Undo the anti tilt device 2 Undo the two screws indicated on the back of the washing machine 3 Secure the anti tilt device using the screws as shown in the picture 4 Attach the plastic cups for fixing the tumble dryer s front feet to the washing machine s top cover This is essential as only when the tumble dryer s feet are resting in the plastic cups can you be sure that the
20. utton and switch on the machine with the main power switch Then press the Stopbutton 5 times within 10 seconds Select the setting you want to change by turning the programme selector Press the Stopbutton once Change and save the setting as described below Press Start to return to the programme menu Language 1 Turn the programme selector to choose from US English English svenska dansk norsk Suomea Fran ais Deutsch Italiano Espanol Pyccxun Nederlands 2 Press the Stopbutton once to save the setting Child safe You can activate the Child safe start option to prevent children from starting the machine 1 Turn the programme selector and choose Child safe start on or Child safe start off 2 Press the Stopbutton once to save the setting You can temporarily deactivate Child safe start by pressing Start and Stop at the same time Child safe start will be deactivated for 3 minutes Audible Volume 1 Turn the programme selector and choose Audible Volume on or Audible Volume off to set whether the tumble dryer should audibly indicate that the programme is finished or that an error has occurred 2 Press the Stopbutton once to save the setting Element 2 1 Turn the programme selector and choose Element 2 On 3000W 16A or Element 2 Off 2000W 10A to increase or decrease the heat output 2 Press the Stopbutton once to save the setting oO of W 13 14 Care and cleaning Cleaning the lint
Download Pdf Manuals
Related Search