INSTALLATION MANUAL
Contents
1. A01GIXC053DA A01GIXC011DD A01GIXCO55DB 3 Remove the fixing bracket of the tray unit three IV Installation procedures screws each 1 Turn off the machine and unplug the power cord from the power outlet 2 Remove the sub tray of the machine Remove it while pushing the claws of the sub tray in the direction of the allow shown on the illus tration and unhook A01GIXC013DB A083IXCO06DB 3 Remove the fixing leg and fixing leg cover of the front left leg only when the paper feed cabinet or the desk is mounted A01GIXCOS56DA Peel seals off the machine two seals LL AIL LU Ml A083IXC007DA 5 Install the mounting bracket A four screw A s fur 8 Align the hole of the finisher unit to the positioning nished with the finisher pin then set it all the way in Note Note The clearance between the mounting bracket A e Set it so that the hole indicated in the illustration and the machine must parallel will meet the stabilizing pin e When carrying the finisher unit hold the posi tions as shown on the illustration LLY NIL A01GIXC057DB Clearance A01GIXCO58DA Machine 9 Set the tray unit Note To set the tray unit use the area of A as a guide Mounting bracket A 9J08IXC082D2. 5 Remove three fixing brackets on the left side of the finisher unit two screws 9J08IXC018DD 6 Remove the protective layer Note Take care so that the mylar will not be bent Protective layer el BOSS SIZ 9J08IXC019DC 7 Remove the protective tape on the front side of the finisher unit 9J08IXC020DC 8 Remove two screws at the bottom of the finisher unit and remove the fixing bracket 9J08IXC021DC 9 Remove the fixing bracket upper on the front side of the finisher unit two screws 10 Remove the fixing bracket lower on the front side of the finisher unit two screws 11 Remove the fixing bracket on the right side of the finisher unit two screws 9J08IXC023DB lt Tray unit gt 1 Raise the box of the tray unit and remove the tray unit from the box Note When removing the tray unit from the box grasp the tray unit at the areas as shown in the illustra tion below A01GIXCO08DA A01GIXC051DA A01GIXC041DB Note 2 Remove protective tape from different parts of the e Set the tray unit upright on the table to conduct tray unit operation Note Take care so that the plate spring on the tray Be sure not to remove the stopper until the tray unit will not be bent unit is installed into the main unit Plate spring
3. B 6 When the punch kit and the saddle stitcher are to be mounted along with the finisher mount the punch kit and the creasing unit for the saddle stitcher to the finisher Note For the punch kit and the saddle stitcher mounting procedures see installation manual for them 7 Remove the job separator JS 505 if it is A01GIXCOS9DA mounted on the machine Note For the removal procedure see the installation manual for the job separator JS 505 A01GIXCO60DA 10 Fix the tray unit to the machine four screw A s furnished with the finisher Note Adjust the casters to align the screw holes A01GIXC061DA 11 Install the mounting bracket B two screw B s furnished with the finisher Note Mount it so that the protruding part will face upward A01GIXCO62DA 12 Remove the exit tray mounting holder and install two shoulder screws furnished with the finisher 13 Reinstall the exit tray mounting holder that has been removed in step 12 one screw 14 Remove the locking tape and the tag A01GIXCO64DA f A01GIXC065DA A01GIXC063DA 16 Attach the stopper which was removed in step 15 to the pos
4. FS 519 Finisher INSTALLATION MANUAL Applied Machines C353 C253 C203 C353P COLOR MFP Color B amp W 35 ppm 35 ppm 25 ppm 25 ppm 20 ppm 20 ppm COLOR PRT Color B amp W 35 ppm 35 ppm Product Code A02E Note Lifting the machine in an awkward position or transporting it in a poorly balanced position could Right cover result in personal injury When transporting the 5 S machine assign an adequate number of persons XS to the job and ensure that each person can take a gt good position of not being excessively loaded mass approx 33 kg 72 3 4 Ib SJoBIXCOO DA Mounting bracket A Name Shape Accessory parts No Name N 9J08IXC010DA 1 Finisher unit Mounting bracket B C 9J08IXC011DA Ly Yyp U 9J08IXC012DA Tray unit Adjusting plate Exit tray upper 4349U015AA Retaining plate 4349U016AA Label Secondary cover 9J08IXCO88DA 9J08IXC004DB s Frontaovap Be sure to keep the adjusting plate which is used when the machine is not equipped with the paper feed cabinet and desk 9J08IXC005DA Connector cover 9J08IXCOO6DA E A01G 9570 01 Name Screw A 4 x 18 mm 9J08IXCO75DA Screw B 3 x 8 mm 9J08IXC077DA Ill Removing protective tape packing and other shipping materials l
5. ition shown in the illustration i g A01GIXCO66DA 17 Pull the lock release lever and remove the fin isher from the machine A01GIXC067DA 18 Connect the three connectors and a ground wire one screw C furnished with the finisher Note Route the connectors bundle of harness and ground wire in a way that one is not placed over the others and the space indicated with the circle on the illustration is secured Make sure that the ground wire is not routed over the connectors illustration A and the bundles of harness do not face downward illustration B A01GIXC022DB lt OK gt Bundle of harness A01GIXC044DA Illustration B lt NG gt 19 Install the connector cover one screw E fur nished with the finisher Fit claws two points into the slots first A01GIXC023DB 20 Install the secondary cover two screw C s fur nished with the finisher Note Make sure that there is a uniform clearance between the misfeed clearing dial and secondary cover A Clearance A01GIXCO70DA A01GIXCO46DA A01GIXCO45DA 21 Install the right cover two screw D s furnished with the finisher Fit claws three points into the slots first A01GIXC071DA 22 Loosen two screws and move the hinge up 23 Set the front cover and move the hinge down to fi
6. removed in step 33 two covers A01GIXCO49DA 36 Set the finisher to the machine 37 Measure the width of Y and Z clearance of the exterior parts on front and back side Specifications Y Z 1 mm Y must be smaller than Z Z 7 2 mm front side Z 9 2 mm back side Note To measure the front side open the front door and measure it using finisher side as supporting point refer to lt Front side measuring method gt shown on the illustration below t7 A01GIXC078DA A01GIXC035DC 38 Lower the left casters until the width of Y and Z is within the specifications For adjusting the casters hold the bottom part of the stand table and turn the adjusting bolt A01GIXC080DA 39 Affix the labels to the position shown below lt Reverse automatic document feeder gt A01GIXC037DA lt by the FD original scale gt A01GIXC038DA
7. t Finisher unit gt Note Place the finisher unit beforehand on the table in a way that the front cover will be off the table Screw C 3 x 8 mm 9J08IXCO78DA Screw D 4 x 8 mm 9J08IXCO79DA Screw E 4 x 8 mm 9J08IXCO80DA Screw F 3 x 8 mm 9J08IXC081DA PTR Cees x f P la a D 44 rd Cn A01GIXCO03DA Shoulder screw GQ lt Q a0 Q Q c0 aH 4582U010AA Installation manual 4980IXC019DA Remove the protective sheet and tape from the finisher unit A WARNING After unpacking be sure to get rid of the D packaging materials and keep them out of the reach of children Putting the head in the plastic bag involves danger of suffocation Note When the punch kit and the saddle stitcher are to be mounted along with the finisher mount the punch kit and the creasing unit for the saddle stitcher to the finisher before mounting the finisher unit to the machine Il When installing to C353P This manual provides the illustration of the machine used as MFP However the same installation proce dure is used for C353P A01GIXCO04DA Remove the front cover two screws A01GIXCOO5DA 3 Remove the fixing bracket of the front cover one screw A01GIXCOO6DA 4 Remove protective tape from different parts of the front cover A01GIXC007DA
8. x the front cover A01GIXC072DA Tighten the screws that have been loosened in step 22 Install the band and the retaining plate to the front cover one screw F furnished with the fin isher Close the front cover A01GIXC073DA 27 Push the board box all the way to the lock posi tion 28 Set the finisher to the machine A01GIXCO74DA 29 Install the upper exit tray two screw F s fur nished with the finisher Note To prevent problems be sure to securely tighten the screws A01GIXCO75DA 30 Connect the hookup cord to the machine A01GIXC081DA 31 Measure the width of X Specifications 5 2 mm Note e If X is out of the specified range follow step 32 and later to adjust the finisher height e If X is within the specified range height adjust ment is not required Move to step 37 YF A01GIXC077DA 32 Pull the lock release lever and remove the fin isher from the machine 33 Remove a cover from each stand leg two A01GIXC047DA 34 Loosen the two screws left and right shown in the illustration and make the height adjustment Then tighten the screws A01GIXC048DA 35 Reinstall the covers that have been
Download Pdf Manuals
Related Search