USER MANUAL
Contents
1. NOTICE FOR CUSTOMERS IN THE UNITED KINGDOM WARNING If the plug supplied is not suitable for the socket outlets in your premises it should be cut off and an ap propriate plug should be fitted in accor dance with the following instructions IMPORTANT The wires in the mains lead are coloured as follows GREEN and YELLOW EARTH BLUE NEUTRAL BROWN LIVE As the colours of the cores in the mains lead of this equipment may not corre spond with the colour markings identifying the terminals in your A the plug proceed as follows The green and yellow lead must be connected to the ter minal in the plug marked with the letter E or with the earth symbol or coloured yellow and green The blue lead must be connected to the terminal that is marked with the letter N or coloured black The brown lead must be connected to the terminal that is marked with the letter L or coloured red 7 1 REAR PANEL CONNECTIONS A Connect the printer to the mains with the power cable supplied B Use a serial cable type D 9 pins to connect the printer to an external control device PC terminal etc and connect it to the serial port point 1 figure 4 C Turn the printer on with the switch point 2 figure 4 8 OPERATIONS PRIOR TO USE WARNING Before carrying out the operations described below turn the printer off with the power switch and remove the2. as shown in point 2 of figure 11 Feed the paper between the printhead and the rubberised roller point 2 figure 11 Feed through a strip of at least 20 cm and remove all of the labels from it Pass the backing paper over the dispenser bar point 1 fig ure 12 The backing paper should then be fed under the rubberised roller point 3 figure 11 ST 302 amp ST 312 USER MANUAL Page 7 Wrap the backing paper around the rewinder two or three times in an anti clockwise direction and secure it with the metal fork point 4 figure 11 printhead in printing mode and secure the pressure bar Reposition the Fig 11 Fig 12 DATAPROCESS EUROPE S p A D Leptons 4 3 LOADING _OF _LABE ROLL FOR REWINDING ONTO EXTERNAL REWINDER This technique is used when there is a large quantity of la bels to be printed and the la bels are to be rewound onto a roll WARNING To operate in re winding mode the printer must be equipped with the optional external unwinder rewinder After loading the roll feed the label strip through as shown in paragraph 9 1 10 LOADING RIBBON FOR ST312 OF Prepare the printer with the covers open and the printhead raised as shown in paragraphs 8 1 and 8 2 Take the ribbon roll and posi tion it upon the unwinder shaft point 1 figure 13 WARNING The ribbon roll is unwound in an anti clockwise direc tion as shown in figure
3. SCHUKO plug of the power cable from the mains socket 8 1 OPENING THE FRONT AND SIDE COVERS Looking at the front of the printer open the front flap point 1 figure 5 and then raise the side cover point 2 figure 5 ST 302 amp ST 312 USER MANUAL Page 5 8 2 RAISING THE PRINTHEAD Raise the printhead from the printing position by turning the steel lever in a clockwise di rection as shown in figure 6 The ST 312 has a black lever instead of the steel lever which functions in the same way Turning the mecha nisms in an anti clockwise direction repositions the printhead in printing mode Fig 5 Fig 6 Fig 7 8 3 REMOVING BACKING PAPER FROM REWINDER DATAPROCESS EUROPE S p A D Leptons Any backing paper on the re winder should be removed af ter freeing the retainer roll by red knob turning the in a clockwise direction as shown in figure 7 Turning the knob in an anti clockwise direction reposi tions the retainer roll to the feeding roller 9 LOADING OF LABEL ROLL Prepare the printer with the covers open and the printhead raised in accordance with the instructions in para graphs 8 1 and 8 2 Remove the disc from the roll holder by pulling it towards you figure 8 Load the label roll on the roll holder and block it with the disc figure 9 After these preliminary opera tions the following sections explain how to use the printer in t
4. Reconfigure the printer ETRE tion printhead energy speed using the correct parame Poor print quality in all areas of ters the label The printhead is worn or ap plied to the label Try printing whilst exerting a slight pressure on the printhead Call for technical assistance if necessary Replace the head or call for technical assistance Dirty printhead Clean the head with suita ble solvent Printhead worn or damaged Poor print quality parallel lines Replace the head or call for in the direction of the paper Rubberised roller is dirty technical assistance feed worn or damaged Clean the roller and call for technical assistance to re place it if necessary Dirt between the paper and the Make sure that materials ribbon used are upto standard Poor print quality light areas Unsuitable paper Replace with better quality paper Rubberised roller is damaged Check the roller and call technical assistance to re place it if necessary The printhead is dirty or da Clean with a suitable sol maged vent and replace the head if necessary or call for tech White lines in the direction of Internal fault nical assistance the paper feed AVANZAMENTO CARTA Call for technical assistan ce ST 302 amp ST 312 USER MANUAL Page 18 16 APPENDIX A 16 1 Interface with ex ternal devices This range of printers has been designed to be easily interfaced with most of the equipment used in any
5. company e SERIAL INTERFACE 16 2 SERIAL INTERFACE The terminal pins os the Cannon 9 pin female con nector enable the printer to communicate in a bidirec tional asynchronous mode with external control devices e g personal computers and other equipment with a compatible interface The following table repre sents the pins and signals The terminal pins of a serial cable for a personal com puter which has a serial port with a Cannon 25 pin con nector are shown in figure 22 DATAPROCESS EUROPE S p A D Leptons PIN SEGNALE DESCRIZIONE 1 Notconnected 2 RxD Datareceived input signal 3 TxD Data transmitted output signal 4 Notconnected 5 GND logicalground 6 Notcomnected 8 CIS Cleartosend input signal 9 Notcomected ________ Table 1 Fig 22 ST 302 amp ST 312 USER MANUAL Page 19 DATAPROCESS EUROPE S p A D Leptons The terminal pins of a serial cable for a personal com puter which has a serial port with a Cannon pin connec tor are shown in figure 22 Fig 23 ST 302 ST 312 Cannon 9 pin ST 302 amp ST 312 USER MANUAL Page 20 DATAPROCESS EUROPE S p A o Leptons INDEX 1 GENERAL INFORMATION 11 211rrrniiii eee 1 2 PRODUCT DESCRIPTION 1 1rrsrcrieee iii 1 3 TECHNICAL SPECIFICATIONS 11 210rrrsai rire iii
6. 2 4 UNPACKING ANDINSPECTION 111 2 1rreni iii eee 3 GEN EE 4 4 2 List Of internal components i 4 S STORAGE i Li LIL LIL LIL LLANO 4 D WORKPLACE civinnsiininnnnzoniniozizionen zizi sinzizanenzinianionizionezizioneiziiozeniniza nazio inizio niorezinionine 5 T MAINS CONNECTIONS cicci inizi aaa dai 5 7 1 REAR PANEL CONNECTIONS edi 5 8 OPERATIONS PRIOR TO USE 11 11rrrsi iii reni 5 8 1 OPENING THE FRONT AND SIDE COVERS iii 5 8 2 RAISING THE PRINTHEAD Fair ine ihre opio NAZ SEZARE SAR ASA Prop O ARESE RA ab RE ABAGRAA GA A SAGRA SIAE LASA ASA BODA AAA 6 8 3 REMOVING BACKING PAPER FROM REWINDER iii 6 9 LOADING OF LABEL ROLL 1 21xrrncc reina iii 6 9 1 LOADING OF LABEL ROLL FOR STRIP MODE ii 7 9 2 LOADING OF LABEL ROLL IN LABEL DISPENSING MOD 7 9 3 LOADING OF LABEL ROLL FOR REWINDING ONTO EXTERNAL REWINDER ooncccnccniocininncnno 8 10 LOADING OF RIBBON FOR ST312 1 111vssssreeeeaiii eee 8 11 FINAL OPERATIONS tool ee ge detent sree tun deine Suis ete ee de 9 12 USINGTHE PRINTER 0 a Nay dieat inuiti 9 12 1 FRONT PANEL AND OPERATING FUNCTIONS ii 11 122 OPERATION KEYS a acacia 11 12 3 LUMINOUS DISPLAYS ae Nee steet louie daddies ial adiae 12 13 MAINTENANCE OF THE PRINTER 14 13 1 CLEANING THE PRINTHEAD cnn rra cnn EnA nnn nn n nn nennnnnnnnnns 14 ST 302 amp ST 312 USER MANUAL Pag
7. MANUAL Page AND Open the packaging and check that the following stan dard parts are included as shown in figure 1 4 1 List of parts User Manual Printer ST302 or ST312 Power cable Dust cover 4 2 List of internal compo nents e Label roll blocking clamp e Ribbon roll retaining disc only with ST312 e Ribbon roll rewinder blocking fork only with ST312 e Backing paper rewinder blocking fork WARNING The USER MANUAL contains safety instructions for the printer and should be re nead AN D A Retain the carton and packaging materials as these may be useful if the printer is to be moved DATAPROCESS EUROPE S p A D Leptons Fig 1 Inspect the printer for any damage which may have arisen during transport and in particular 1 Check the entire outer part of the printer 2 Open the side cover and check for any internal damage In the event of visible damage 3 Immediately notify the transporter of the damage sustained by the printer 4 Keep all packaging mate rials for inspection by the transporter 5 Prepare a detailed report including the extent of the damage and trans porter used and advise DATAPROCESS EUROPE SpA and or your local Dealer WARNING DATAPROCESS EUROPE SpA is not in any way liable for damage sustained during the transport of the equip ment and will not repair the equipment under warranty 5 STORAGE If
8. option has been di sactivated in the configura tion The PRINT light will come on while the label is being printed ST 302 amp ST 312 USER MANUAL Page 9 DATAPROCESS EUROPE S p A D Leptons ST 302 E1 2 19 247 032 000 08 35 40 un 05 Feb 1996 00000 gt P120078093187240 P078H0270 G00000008N00000000 00 K1000J1506V08105800 amp 0000000000000000 gt T302C0561599680174B1100002A202A2 Ymax 199 mm gt S2000104010100 gt B28N1 gt A00 gt C gt L000 HON 0 05 LP 19 TI3 ist label printed when D nter is switched on is shown in figure 15 and is divi ded into the following sections ST 302 8 ST 312 SWON 0 KP 0 001 Fig 15 PRINTER MODEL ROM TYPE FIRMWARE VERSION SERIAL NUMBER 2 PRINTHEAD TEMPERATURE PHOTOSENSOR SENSITIVITY LABEL FEED END OF PAPER END OF RIBBON 3 DATE AND TIME 4 TEST TO CHECK THE PRINTHEAD OPERATION AND ALIGNMENT THIS CONSISTS OF A BLACK AREA AND A GREY AREA WITH VERTICAL AND HORIZONTAL BARS 5 CURRENT PARAMETER VALUES IN THE NON VOLATILE MEMORY The current values of the pa rameters contained in the non volatile memory are DESCRIPTION IDENTIFICATION OF THE PRINTER AND THE MEMORY CONFIGURATION PARAMETERS PARAMETERS gt S FOR THE LABEL PAPER FEED PARAMETERS gt B FOR THE SERIAL INTERFACE NETWORK ADD
9. 13 Position the disc in one of the four grooves between the un winder shaft and the internal core of the ribbon roll in such a way that the ribbon roll is firm and secure point 2 figure 13 ST 302 amp ST 312 USER MANUAL Page 8 Take the first part of the rib bon usually transparent or metal foil and pass it around the outside of the two guide shafts shown in point 3 of fig ure 13 and then between the black rubberised roller and the printhead Fix the ribbon to the rewinding shaft and use the metal fork to secure the ribbon as shown in points 4 and 5 of figure 13 Rewind the ribbon a number of times in an anti A clockwise direction un til the transparent part has completely disappeared and the inked part is positioned under the printhead Fig 13 Fig 14 Reposition the printhead in printing mode DATAPROCESS EUROPE S p A D Leptons 11 FINAL OPERATIONS Close the covers starting with the side panel and then the flap at the front as shown in points 1 and 2 of figure 14 WARNING Whilst closing the covers the side panel must always be guided 12 USING THE PRINTER When the printer is switched on the POWER LED will light up and after a brief initiallisa tion process the LINE light comes on If the printer is in normal working conditions with labels and ribbon only in the case of the ST312 correctly installed a test label is printed unless this
10. DATAPROCESS EUROPE S p A D Leptons ST 302 ST 312 USER MANUAL REL 1 2 DATAPROCESS EUROPE S p A 1D 20082 Binasco MI Viale dell Artigianato 19 Sec Tel 02 90022 1 Fax 02 90091353 ST 302 amp ST 312 USER MANUAL Page 1 GENERAL INFORMATION This USER MANUAL con tains all of the information and instructions necessary to en sure that the ST302 or ST312 printer functions prop erly over a lengthy period of time Maintenance must be carried out at regular intervals and any repairs if required must be undertaken at our premises or by our Authorised Distributors who have the necessary equipment and qualified per sonnel trained in accordance with our technical instructions DATAPROCESS EUROPE SpA declines any responsibility due to incorrect maintenance undertaken by unauthorised technicians nor shall it be held liable for any damages arising from the use of uncertified spare parts DATAPROCESS EUROPE SpA declines any responsibility for damages which may be sustained directly or indirectly by persons or things arising from installation or use of the ST302 or ST312 printer which differs from that stated in this manual The ST302 or ST312 printer must be installed in accor dance with the safety pre cautions and installation procedures contained in this USER MANUAL DATAPROCESS EUROPE SpA declines any responsibility for damages arising from the incorrec
11. MENTAL TEMPERATURE HUMIDITY 192 mm 392 mm 195 mm Thermal transfer ST312 Thermal direct ST302 8 dots mm Variable from 50 to 150 mm sec Variable from 50 to 150 mm sec 56 mm equivalent to 448 dots Upto 200 mm equivalent to 1600 scanlines Upto 200 mm From 40 to 63 mm Maximum 140 mm From 40 to 45 mm From 60 to 200 um from 50 to 180 g m 5 mm from the label edge Three fixed space fonts fonts fonts for logos character set five proportionally spaced and symbols international Code 39 Code 93 Interleaved 2 5 Codabar EAN 8 EAN 13 EAN 128 UPC A UPC E Code 128 Add on ITF 14 ITF 16 RS232C asynchronous serial full duplex From 300 to 38 400 bits sec RTS CTS XON XOFF with 64 kb reception buffer 230 VAC 6 10 50 60 Hz 200 VA 10 kg From 5 to 35 C From 20 to 90 without condensation ST 302 amp ST 312 USER MANUAL Page The maximum height is based on the ST302 or ST312 basic printer 256 kb memory With op tional memory expansion the maximum height can be extended to 492 mm 384 kb or to 784 mm 512 kb These values are based on single bitmap configuration The maximum heights that can be achieved with double bitmap con figuration are exactly half i e 100 mm 256 kb 246 mm 384 kb 392 mm 512 kb DATAPROCESS EUROPE S p A D Leptons cle LS Y C0 LS 4 UNPACKING INSPECTION ST 302 amp ST 312 USER
12. RESS PHOTOSENSORS SENSITIVITY SENSITIVITY LABEL PHOTOSENSOR PARAMETER COMMAND USER MANUAL Page 10 DATAPROCESS EUROPE S p A D Leptons WHICH CONTROLS THE LABEL ALIGNMENT PRINTING AREA INITIAL COORDINATES a PARAMETERS MODE PRINT SPEED AND VIEW PRINT PRINTHEAD ENERGY The last two lines of the la bel show the values of some of the printers internal counters HON 0 05 TOTAL AMOUNT OF TIME THE PRINTER HAS BEEN SWITCHED ON SWON 8 NUMBER OF TIMES THE PRINTER HAS BEEN SWITCHED ON LP 19 TOTAL NUMBER OF LABELS PRINTED KP 0 000 TOTAL NUMBER OF KILOMETERS OF PAPER PRINTED same as the one used for cor responding commands which can be sent from aan external control device A complete desscription of the commands on the test label is included in the PROGRAMMING MANUAL 12 1 FRONT PANEL AND OPERATING FUNCTIONS The ST302 and ST312 prin ters are equiped with a front command panel consisting of two buttons and a series of lights The panel is shown in figure 16 on the next page 122 OPERATION KEYS The two buttons on the front panel have the following functions Switches from ONLINE or PRINT to OFFLINE status or vice versa The format used to represent the parameter values is the ST 302 amp ST 312 USER MANUAL Page 11 If the printer is in OFFLINEstatus this button can be used to print a copy of th
13. cohol to wipe the rubberised rollers clean of any dirt residues of adhesives and ribbon rolls which may have accumulated during the printing of the labels as shown in figure 19 The printer s printing quality is significantly affected by the condition of the rubberised rollers as these are the me chanical components which feed the paper through If they are dirty the paper may slip and consequently affect the print quality 133 CLEANING THE METAL PAPER FEED SHAFTS The metal paper feed shafts should be cleaned to eliminate the adhesive residues which are deposited by the adhesive labels They should always be kept clean as the adhesive residues from the labels create a sticky surface which prevents the la bel roll from moving freely DATAPROCESS EUROPE S p A D Leptons Use a soft cloth dampened with isopropyl alcohol and wipe the metal paper feed shafts as shown in figure 20 13 4 CLEANING PHOTOSENSORS THE The photosensors should be cleaned with a soft brush or compressed air jet to remove dust residues deposited by the label roll as it unwinds The position of the photosensors is shown at points 1 and 2 in figu re 21 Once the maintenance has been completed reload the la bel roll and only for the ST312 the ribbon and then close the side panel and front flap The printer can now be switched on again 14 TRANSPORTATION 1 Switch the machine off 2 Disconnect th
14. e 21 DATAPROCESS EUROPE S p A Leptons 13 2 CLEANING THE RUBBERISED ROLLERS iii 13 3 CLEANING THE METAL PAPER FEED SHAPFTG 10 ccccseccccceeeececcesecceceneeccscnneecessneeeeenans 13 4 CLEANING THE PHOTOSENSORBRS iii 14 TRANSPORTAT ON a tanata e 15 TROUBLE SHHOTING rene ene e nese eni eee eni eee 165 APPENDIX A nin ini Ee 16 1 Interface with external dewdcesg iii 16 2 SERIALINTEREAG Eege dE ae india o a ST 302 amp ST 312 USER MANUAL Page 22
15. e last label prin ted or to feed through a blank label depending on the prin ter s configuration Pressing both of the buttons together will abort the current printing session The printer s reset pro a cedure is activated FEED en the two buttons sed together at the same time as the printer is switched on The default parameters are then loaded into the non volatile Memory The menu for the cali bration of the printer and the setting of the label lenght is accessed when the PAUSE button is pressed at the same time as the ma chine is switched on Figure 16 shows the control panel in detail Fig 16 DATAPROCESS EUROPE S p A D Leptons O power O line O print 123 LUMINOUS DISPLAYS The three different coloured lights on the front panel ha ve the following significance POWER This red light indi cates that the printer is switched on LINE This green light indi cates the status of the Com mand Interpreter and can de note 4 different circumstances e ON printer is ON LINE and can process the data it receives Indicates that the e IRREGULAR FLASHING Indicates that the Com mand Interpreter is pro cessing data in the recep tion buffer e REGULAR FLASHING Indicates that the printer requires additional data to complete a command or that the printer is waiting for variable data e OFF Indicates that the Command Interpreter is not processing data becau se the p
16. e pwer cable from the mains supply and then from the printer 3 Disconnect the serial cable 4 Place the printer into its ori ginal packaging NOTE If the printer is to be transfered to another area check the environmental spe cifications as per Chapter 3 Technical specifications ST 302 amp ST 312 USER MANUAL Page 15 DATAPROCESS EUROPE S p A D Leptons 15 TROUBLE SHHOTING Some minor problems may be easily resolved by the operator If the ST302 or ST312 printer should not function properly consult the points listed in the following tables before calling Technical Assistance PROBLEM POSSIBLE CAUSE ACTION Check the power The printer has not been pro lag ane maine sue perly connected to the mains supply RES Unplug the power cable and check that the fuses on the rear The printer does not come on panel have not blown the POWER light does not Faulty fuse Replace any blown fu light up ses with the same ty pe fuse Call for technical as sistance Internal fault The printer comes on but Labels and or ribbon have not Load the labels and or ribbon does not print the test label been loaded gt Move the printhead into the The printhead is raised print position ETICHETTA DI TEST DISABILITATA Set up the printer again ST 302 amp ST 312 USER MANUAL Page 16 DATAPROCESS EUROPE S p A D Leptons PRPBLEM POSSIBLE CAUSE ACTION The p
17. he following modes e STRIP MODE e DISPENSING MODE e REWINDING MODE ST 302 amp ST 312 USER MANUAL Page 6 9 1 LOADING OF LABEL ROLL FOR STRIP MODE This mode is more suitable when there is a small quantity of labels to be printed and they can be allowed to flow freely from the printer After loading the roll proceed as follows Fig 8 Fig 9 Fig 10 Take the strip of labels and pass it over the first roll guide and under the second roll guide point 1 figure 10 If necessary adjust the paper guides on the roll guides to suit the width of the label roll WARNING Ensure that the paper strip passes through the photoelectric cells posi tioned near the roll guides as shown in point 2 of figure DATAPROCESS EUROPE S p A D Leptons printhead and the rub oller point 3 figure 10 printing mode 9 2 LOADING OF LABEL ROLL IN LABEL DISPENSING MODE This technique is used when the labels are to be dispensed removed from the backing paper one at a time to be then applied manually to a product to be labelled After loading the roll proceed as follows Take the label strip and feed it over the first roller guide and under the second point 1 fig ure 11 If necessary adjust the paper guides on the roll guides to suit the width of the label roll WARNING Ensure that the paper strip passes through the photoelectric cells posi tioned near the roll guides
18. ortnightly cleaning is suffi cient A brush or air jet can be used to remove dust residues from labels and particular care should be taken in cleaning the label and ribbon detection photosensors The printhead rubberised rol lers and paper feed shafts should be cleaned with a soft cloth dampened with a mild solvent like denatured alcohol or isopropyl alcohol DATAPROCESS EUROPE S p A D Leptons WARNING Do not use metal or hard objects to clean the printhead or rubberised rollers see figure 17 Before carrying out mainte nance the operator must fol low these instructions WARNING The printer must be switched off at the rear panel and the plug must be removed from the mains Prepare with the front and side panels open see paragraph 8 1 Raise the printhead see pa ragraph 8 2 Remove the the label roll and in the case of the ST312 the ribbon roll The printer is now ready for maintenance to be undertaken as follows 13 1 CLEANING THE PRINTHEAD Use a soft cloth or cotton bud dampened with isopropyl al cohol and gently rub it along the length of the printhead to wipe away all the residues from the printhead figure 18 ST 302 amp ST 312 USER MANUAL Page 14 The print quality is si 8 eur improved by a clean printhead and rubberised roller 132 CLEANING RUBBERISED ROLLERS THE Use a soft cloth dampened with isopropyl al
19. rinter does not respond to commands from the exter nal control device The labels feed through without being printed Irregular paper feed ST 302 amp ST 312 USER MANUAL Page Unsuitable or defective cable or cable not properly con nected Communication incorrect parameters Internal fault The printhead is raised Printhead connection cable and power supply flat Defective printhead Internal fault Dirty damaged or worn rubbe rised roller Incorrect paper path The labels stick Check the cable and replace if necessary Check that the printer baud rate corresponds to the ex ternal control device rate and ensure that the device rate and ensure that the compati ble with those of the printer Call for technical assistance Lower the printhead to the print position Ensure that the flat cable is correctly plugged into the printhead connector and that the head power cable is cor rectly plugged in Replace the printhead or call for technical assistance Call for technical assistance Clean the roller with suitable materials or call for technical assistance to replace it Check that the label roll has been correctly loaded Use a suitable solvent to re move any adhesive residues 17 DATAPROCESS EUROPE S p A D Leptons PROBLEM POSSIBLE CAUSE ACTIONION Unsuitable paper and or rib Replace with appropriate bon paper and or ribbon Incorrect configura
20. rinter is either OFF LINE or PRINTING PRINT This yellow light gives information on the current O printing session It is OFF when the printer is not printing or when there is no print pending the print com mand may have been received but not immediately proces sed It is ON when there is a printing session in progress or even when the printer may not actually be printing because it is awaiting variable data The light FLASHES when the printing session has been su spended for any reason pause command printing error syn chronisation problems with the external device etc The in terval at which the light flashes indicates the reason for the interruption if the error can be automatically re covered or whether the opera tor has to correct it manually see the relevant paragraph on return messages in the O PROGRAMMING MANUAL ST 302 amp ST 312 USER MANUAL Page 12 DATAPROCESS EUROPE S p A D Leptons cle LS Y C0 LS ST 302 amp ST 312 USER MANUAL Page 13 MAINTENANCE THE PRINTER OF As the printer only has a few moving parts there are no spe cial maintenance requirements other than a periodic cleaning of the parts that can get dirty e PRINTHEAD e RUBBERISED FEED ROLLER e METAL PAPER SHAFTS e LABEL DETECTION PHOTOSENSORS PAPER FEED It is advisable to carry out maintenance on a weekly basis if the printer is subject to heavy usage otherwise monthly or f
21. t installation mainte nance or improper use DATAPROCESS EUROPE S p A D Leptons cle LS Y C0 LS of the printer nor can it be held liable for any loss of income or expenses arising from any fail ure of the printer 2 PRODUCT DESCRIPTION The ST302 and ST312 models are part of a range of printers for self adhesive labels and tags which operate by direct thermal or thermal transfer technology The printers have been de signed in such a way that they can operate in any company environment where heavy work loads and high standards are required Specific knowledge or equip ment are not required for in stallation however for safety reasons the instructions given in section 6 of this manual must be strictly followed The printer is extremely simple to use and does not require any preliminary operations other than the loading of the label roll and ribbon as de scribed in the relevant sec tions ST 302 amp ST 312 USER MANUAL Page 1 DATAPROCESS EUROPE S p A D Leptons 3 TECHNICAL SPECIFICATIONS PRINTING METHOD PRINTHEAD RESOLUTION PRINT SPEED PAPER FEED SPEED PRINTING AREA WIDTH HEIGHT MAXIMUM LABEL LENGTH LABEL ROLL DIMENSIONS WIDTH EXTERNAL DIAMETER INTERNAL DIAMETER PAPER THICKNESS LABEL SENSOR TRANSPARENCY SENSOR FONTS BARCODES STANDARD INTERFACE BAUD RATE PROTOCOL MAINS SUPPLY ABSORBTION SIZE WIDTH DEPTH HEIGHT WEIGHT ENVIRON
22. the printer is not to be used straightaway it should be stored in its original packaging The environmental conditions for storing should be Room tem from 5 C to 35 C perature ST 302 amp ST 312 USER MANUAL Page 4 Relative from 20 to 90 humidity without conden sation 6 WORKPLACE The ST302 or ST312 printer can be placed on any flat sur face provided that it is sturdy the printers weight and that there is enough space for the printer and its accessories Adequate space should be left around the printer to ensure that it is properly ventilated 7 MAINS CONNECTIONS WARNING The printer must be connected to the mai using the cable supplied 1 Plug in the female conhec appropriate socket on printer s rear panel point 1 of figure 2 A 2 Connect the SCHUKO plug of the power cable as shown in figure 3 to a Fig 2 Fig 3 DATAPROCESS EUROPE S p A D Leptons compatible socket which has an electrical output 230VAC 6 10 50 60 Hz WARNING Make sure that the power cable is con nected to mains which are earthed The mains should conform to EU regulations in force
Download Pdf Manuals
Related Search