BlueGateBrave user guide 2.4 .DOC
Contents
1. MLPHIN Tech G S M G AT E ALPHA Installation guide V 2 4 Basic features Blue Gate A Brave is dual band GSM Gate based on Telit GL865 equipped by a lot of adjustable features increased comfort of service It has been designed for GSM network 850 900 1800 1900Mhz e Polarity reversal of telephone line allows exact detection of start and end of call e CLIP support all ordinary protocol e Call billing allows control exact call duration due tax pulses 12 16 kHz 1 pulse when outgoing call is picked up e Beeps in minute period into the call allows easy identification of GSM call e Monitoring syst m allows sending SMS to preprogrammed number when voltage of Back up batteries drops unit is logged to GSM network no picks up number of ringing called person connected device doesnt react for ringing etc e Possibility of individual ECHO canceler setting up local conditions Options e Option USB port with PC software allows you easy configuration as same as sending and receiving SMS messages via SMS mail sw or data transmission e You can add a backup battery for up to 10 h of operation at power failure e Sending of status SMS 1 30 days adjustable e 2 inputs with SMS sending feature when inputs status is changed up settings Thanks of many BlueGate features you can satisfy very wide group of customers By setting of permitted numbers to memory of BlueGate you can restrict unrequested calls2. 01 19 number of numeral telephone number In n n n Storingof PN O FI Am pici c Sauna tang dire ie i a m CLIR feature switching OFF outgoing CLIP 31 n 0 OFF n 1 ON 10 Eo EK BE B B FR E RE R cereale eee 2 3 mm A o o s s Z 1 x x ly ly Xx 00 No charging pulses Xx 12 12 kHz charging pulses Xx 16 16 kHz charging pulses Yy 00 1 pulse only at the moment of connection Yy 01 to 99 seconds Pulses each 01 up 99 seconds 17 2 n Amplification of sound in incoming direction 1 to 4 LULI 7j3jn n 0 CLIP is switch OFF 1 n 1 FSK CLIP Bell 714 Jn Call progress tone n 0 OFF n 1 ON 7 5 Jn Roaming 1 n 0 prohibited n 1 permitted E Default setting ta 11 Table of tones O e ee A E _ HH Dial tone up setting Mini Gate is ready to accept dial HE EE EEE Busy tone short tone repeated Called part is busy doesnt exist not permitted etc EEE SS BSM Ringing tone long tone and pause repeated Called part is ringing E Waiting tone short tone repated with quick cadence Mini Gate waiting for password insert S E a E Programming short tone with quick cadence i Programming mode of Mini Gate HHE Confirmation inquiry 3 short tones Inquiry to confirm inserted parametr EE Confirmation tone long tone Parametr was saved correctly Minute tone short tone with 1 minute period Minute beep to i
3. Dimensions mm Weight Part of power supply Power supply Protection Safety group Analogue telephopne line telephone interface telephone conector Impedance Dial Billing Start and end of connection Supply conduction Current loop BlueGate A Brave various temperature 20 C 40 C humidity 10 80 at 30 C 100mm x 130mm x 37mm adapter 8 12VAC DC 500mA thermal fuse in adapter CSN EN 60950 group 2 2 wires RJ 11 600 O 20 tone DTMF t gt 30 ms outgoing INBAND OUTBAND 12 16 kHz Polarity reversal 24V max 29 mA Resistance of subscribers conduction max 500 O Ringing Signalization CLIP GSM mobile network provider USB 55 Ve 50 Hz 425 Hz 20Hz FSK Bell Quad Band 850 900 1800 1900Mhz according SIM card 3V and 1 8 V version 1 1 virtual COM 16 Functionality Waiting for dial after pick up 1 99 sec or unlimited Waiting for last digit of dial 1 15 sec Dial after preprogrammed number of digits 1 19 Immediate dial sent up setting K or Permitted direction 9 memories of 4 digits numbers CLIR CLIP Call billing tax pulses 12 16 kHz outgoing DTMF INBAND OUTBAND Reversal polarity start and end of call Roaming ON OFF Call duration control Time beeps in call GSM signal strength identification Sending of preprogrammed SMS to preprogrammed number after voltage drops under setup level and taking longer time than setup time Sendi
4. to public numbers As same as you can set BlueGate to provides incoming calls only INSTALLATION antenna SIM telephone line gt A t telephone line Power supply MiniUSB Insert the SIM card up the picture and by press fix it in operation position Before inserting the SIM card we recommend checking at various mobile phone state of the SIM card logging with or without PIN PIN etc and set logging without PIN When you want logging with PIN you have to preprogrammed this PIN and set logging with PIN via table of programming Without this setting the Gate wont work DO NOT FORGET ANTENNA CONNECTION The available place for installation select up following point of view 1 distance from PBX possibility of GSM interferences to other PBX lines as same as lenght of line from Gate to PBX max 200m 2 main 230 V for power supply of Gate 3 Quality of GSM signal at the installation place of GSM Gate Quality of GSM signal The sound quality depends on BTS setting where you are connected by the Gate To find best place for antenna mounting you can use either mobile phone or yellow LED flashing on front of unit via Table at the end of manual The suitable signal power is 3 scales of mobile graduation To check and find best position from GSM signal point of view you can use also GG SET configuration sw More in manual for GG SET Connection of antenna When you connect magnetic a
5. a command immediately after acknowledge character dialling These parameters can be entered if necessary immediately after switching gates Go into the programming mode in the busy tone see note 3 below Without their setting in some cases may not be available SIM card PIN type of SIM card Notes P Changes are valid after hang up only finishing of programming mode It is very important especially in acknowledge character changes till hang up you must use previous acknowledgement After numbers dialing you must wait for confirming reguest insert acknowledge character and wait for confirming tone When you insert acknowledge charater before wont be accepted Switch to programming mode is possible even in busy tone Some parametres are possible to programm by PC only Table of programming jo o n n n n Password nnnn to programming mode access df gt Type of dial tone n n 0 permanent tone n 1 dial tone up table of tones n 2 dial tone of public lines operator Signalization to the call short tone each minute n 0 tone is turn off n 1 tone is turn on Restriction of call duration n 0 without restriction n 1 call duration restricted at 10 minutes Type of SIM card outgoing DTMF INBAND OUTBAND INBAND DTMF n 1 OUTBAND DTMF Number of dialled numeral after its is dial send immediately lenght of telephone number nn 00 function none active nn
6. e for 2 sec After calling to BlueGate you are hearing busy tone BlueGate is not log into GSM network bad signal The yellow LED communication to GSM is flashing up signal strength After calling to BlueGate is not light up green LED is not light up and in analogue phone is quiet It interrupted conduction of analogue line or so much big resistance in current loop for example longer cabel between PBX and BlueGate Tle yellow LED communication to GSM is flashing up signal strength as same as green LED lights up Tle PBX hold pick up line of GSM Gate By incoming call you can remove this issue In other cases check PBX manual The BlueGate works but call is disturbed by interference Incorrect position of antenna against telephone line Change antenna position Default you make by parametr 99 in programming mode via programming table at page 11 Alle LEDs flashing as same as tone types are mentioned in tables at the end of manual USB You can purchase USB tool for PC configuration of the unit It is optional This tool is connected via 6 wire cable to the units in middle of phone line via picture on page 2 You can control GSM modul directly via virtual COM port The Gate you can further use ordinary GSM modem for data transmission internet connection or for SMS messages When unit is working as GSM modem then is busy for voice connection When you pick up the line you will hear busy tone The unit is m
7. g by hang up a phone SOOOOOS Example programming of new permitted fix numbers 02 to memory 09 Dial acknowledgement default is In phone you are hearing waiting tone 4 Dial password default 0000 Waiting tone is changing to programming tone HH Dial 1902 Wait for tone of confirming request 3 short tones Confirm the feature by dialling acknowledgement Wait for confirming tone one long tone Finish programming mode by hang up a phone Warning After dialling of parametr value you have to wait for 3 short tones and then dial acknowledgement Wait for long tone confirm acceptation of this parametr Notes to each parametres 11 19 When you programm some prefixes the BlueGate A 22 32 35 27 37 Bravellows outgoing calls starts by those prefixes only The others will get busy tone When memories will be empty the calling wont be restricted default Memory of prefixes can content 1 digit only If you insert 1 digit only the BlueGate will check first position only Rewriting of memory by storing of new fix numbers are old fix numbers erased Erasing of memory Memory you will erase by storing of nothing You dial only number of memory which you want erase and confim it very important feature is acknowledge character setting Default is When is used for PBX features you can change it on The GSM phones requested command to connection on inserted number The BLUE GATE will send
8. nform about GSM call Call progress tone short tones 3 s after sending number to GSM Searching of called part 12 LED signalling Permanent light lights up after power connection Power supply of GSM unit Permanent light line OFF HOOK Doesnt light line ON HOOK Flashing in rhytm of busy tone Programming or PC connection mode Flashing in rhytm of busy tone Initialization mode after power supply connection restart after programming etc 1 5 flashes with period 4 sec stand by mode Number of flashes signal strength Permanent light GSM connection is running call Short lights off with period 2 sec GSM modul doesnt communicate to CPU Flashing in period 2sec SIM is not readed 13 Short flashes in period 2 sec Gate is not registrate to GSM network ACU pack installation Backup battery 9 6 V 800mAh 1 Open Gateway cabinet 2 Remove cover of glue tape at bottom part of ACU pack 3 Fix the ACU pack into Gateway cabinet CAUTION for holes for signalling LEDs DO NOT COVER 4 Acu pack must nost be supplied in charged up status Start ae the gateway first and wait for network log in Then connect cable from ACU pack to appropriate connector 5 Close the gateway cabinet and leave ACU charged up at least 2 hours without power supply disconnection 15 Technical parametres Type Operating position Operating conditions
9. ng of preprogrammed SMS to preprogrammed number at every logging to GSM network Sending of preprogrammed SMS to preprogrammed number when number of none picks up rings into connected device incoming call is higher than setup level Sending of preprogrammed SMS to preprogrammed number when inputs status is changed optional board taking longer time than setup time Periodical sending of status SMS in preprogrammed time period 1 30 days SMS includes time and date of sending time setup on gateway clocks GSM network status power supply voltage GSM modul temperature last call number Cz ALPHA Tech Alphatech spol s r o Jeremenkova 88 140 00 Praha 4 tel 272 103 335 fax 272 103 334 e mail alphatech alphatech cz internet http www alphatech cz na e sou adnice GPS WGS 84 N 50902 35 5 E 14925 42 0 15 1 2013 18
10. ntenna keep on mounting at bigger iron subject This subject makes against weight at its depends the power of radiated signal When you inserted SIM card as same as all cables are connected do not forget that Blue gate is connected on external line not on extension connect device to main 230V Blue LED feeding lights up via LED table and starts flashing yellovv GSM LED in rhytm of busy tone After cca 30 seconds the yellovv LED start flashing up GSM signal strength via LED table VVhen pick up connected analogue phone or call to BlueGate from PBX the LED of analogue line lights up green LED In the phone is hearing dial tone of BlueGate It is ready to use The most often problems during Blue Gate compact installation gt All LED is not lighting Problem in power supply Check connection to main 230V as same as connection of adapter to BlueGate gt The LED power supply lights When you make connection to Gate green LED is ON and in handset you hear busy tone Yellow LED flashing in period GSM modul doesnt communicate with CPU During work with USB could be programmed fix communication rate for GSM modul Use USB to programm rate on sautobauding gt The yellow LED flashing in period PIN unreadable After calling to BlueGate you get busy tone The SIM 4 Note card reguires PIN which is not preprogrammed or is preprogrammed wrongly The LED communication to GSM is flash shortly on
11. onitoring data transmission by modem The data transmission can not be permanent therefore the unit stays in data mode 10 seconds after finishing of data transmission Then is going back to Voice mode calling The same is when you are calling over unit It is busy for data transmission The optional sw supply to unit for sending and receiving SMS messages is SMS mail It is working under Outlook Outlook Expres Opera etc And you can work with SMS as with normal e mails see manual for SMS mail It works in batches and allows programm communication interval 1 to 99 minutes to BlueGate for sending and receiving SMS Due this we avoid situation that unit is permanentlky blocked by data mode for voice communication Further functionality of USB is monitoring BlueGate operation It is possible record even incoming calls includes time and CLIP signal strength etc CONFIGURATION The programming mode is set after acknowledgement dialing to Blue Gate In the analogue phone is waiting tone After password inserting is tone changing to programming tone Then you can programming each features of Blue Gate via table of programming Progress of programming Dial 2 digits number of programming feature Dial 1 to 4 digits number for feature value programming Wait for a tone of confirming reguest 3 short tones Confirm the feature by dialling acknowledgement Wait for confirming tone Follow programming tone again Finish programmin
Download Pdf Manuals
Related Search