Operating Instructions
Contents
1. Express cable to the PCI Express connector of the P2 drive and then connect the other end to the PCle interface connector of the PCI Express board already attached to the personal computer After connecting the cable tighten the screws on the connector to firmly attach the connector PCle interface connector Screw lt Notes gt When connecting the cable ensure that both the P2 drive and the personal computer are off Connect after carefully checking the configuration of the PCI Express cable Connecting the ends in reverse will damage internal parts and cause malfunction Use the PCI Express cable included with the P2 drive The unit may not operate properly if a commercially available cable of 2 meters or longer is used Installation continue 7 Connect the AC adapter included with the P2 drive to the unit s DC IN 16V socket Start up the P2 drive Check that the green light on the unit s power indicator turns on and that the status indicators for all card slots blink about once per second oco PCle I F DC IN 16V 0G 8 Start up the personal computer 9 Verify that the personal computer recognises the P2 drive lt Notes gt In Windows XP or Windows Vista some card slots of the P2 drive may be assigned drive names that have already been assigned to existing networks Reassign network drive names if your personal computer do2. Extension cords used with the equipment must be three core and be correctly wired to provide connection to earth Wrongly wired extension cords are a major cause of fatalities The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe For your safety if in any doubt about the effective earthing of the power point consult a qualified electrician indicates safety information Read this first continue For AJ PCD35P FCC NOTICE Declaration of Conformity Model Number AJ PCD35P Trade Name Panasonic Responsible Party Panasonic Corporation of North America One Panasonic Way Secaucus NJ 07094 Support contact Panasonic Broadcast amp Television Systems Company 1 800 524 1448 This device complies with Part 15 of FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation To assure continued compliance follow the attached installation instructions and do not make any unauthorized modifications CAUTION This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interfe
3. If the cable is bent sharply it may disconnect 8 Undo the six screws and remove the cover Installation continue 9 10 Mount the P2 drive in a 5 inch bay on the personal computer Use the screws page 7 supplied with the P2 drive for mounting Please refer to your computer s instruction manual for guidance in mounting to 5 inch bay drives SX L Holes for securing the screws the other side is the same lt Notes gt The P2 drive may not be able to be fastened securely in some types of personal computers If all 5 inch bays are occupied you will need to remove one of the built in drives to make room for the P2 drive The P2 drive should be used in a personal computer whose design allows the front panel of the Drive to be manipulated Connect the other end of the PCI Express cable to the P2 drive PCle interface connector After connecting the cable tighten the screws on the connector to firmly attach the connector DGIN Jev DC IN 12V xm PCle VF is D PCle interface connector Screw Il Connect the P2 drive to the internal power cable 4 pins of the personal computer osiniev i DC IN 12V PCle VF Power cable 12 Start the personal computer and ver
4. NMB 003 du Canada indicates safety information Read this first continue For AJ PCD35E Caution for AC Mains Lead FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY This product is equipped with 2 types of AC mains cable One is for continental Europe etc and the other one is only for U K Appropriate mains cable must be used in each local area since the other type of mains cable is not suitable FOR CONTINENTAL EUROPE ETC FOR U K ONLY Not to be used in the U K oe FOR U K ONLY How to replace the fuse 1 Open the fuse compartment with a This appliance is supplied with a moulded screwdriver three pin mains plug for your safety and convenience A 13 amp fuse is fitted in this plug Should the fuse need to be replaced please ensure that the replacement fuse has a rating of 13 amps and that it is approved by ASTA or BSI to BS1362 Check for the ASTA mark or the BSI mark amp on the body of the fuse If the plug contains a removable fuse cover you must ensure that it is refitted when the fuse is replaced If you lose the fuse cover the plug must not be used until a replacement cover is obtained A replacement fuse cover can be purchased from your local Panasonic Dealer indicates safety information Table of Contents Read this firsth ai hep ett tk fede ct MD hae ek
5. eM od bce thats A ace ne 2 Be fOre USE E Sete p nas secde padenied on ots hans sedis E EE got den E 6 OVErVIOW 0 nent teens 6 FOatuies eka e aaraa hides ahi ack he ela ate Panes en atid Waa ele 6 Supplied Accessories AJ PCD35P AJ PCD35E 0 0 000 ccc 7 Operating Environment Required for Installation 0 0000 c cece eee eee 7 Parts and their Functions 0 000 te eee 8 Front Panel icteric tans att e SS leat ah Oe Baten es 8 Rear Panelis Goera ease A Fane pict ee te ane eke eee a ae ae aE 8 Inserting aP2 Cardz eee rodor a cent eee nes 9 Write protection of P2 Card 1 0 0 0 tee 9 Installations ti ees eel eats Ca der ol a ae MA a a eee ae 9 To Connect the P2 drive to a Personal Computer for External Use 10 To Mount the P2 drive in a Personal Computer 5 inch Bay 12 PCI Express Driver for Windows 0000 cece eee eee 14 1 Before installation 0 0 een eee nee 14 2 Installation of the PCI Express driver 0 20 000 c cee eee 14 3 Confirmation of installation of the PCI Express driver 000 14 PCI Express Driver for Macintosh 00 00 eee eee eee 16 Installation of the PCI Express driver 0 00 200000 e eee eee eee 16 Specifications sins radit aid waked g nie see iw eid weeks ee ee ES ee eet 17 Windows Windows XP and Windows Vista are trademarks of Microsoft Corporation of the United States Macnintosh Mac Pro and Mac OS X ar
6. following procedures I In accordance with the descriptions in 4 Installation of the P2 Software from pages 4 to 7 of the installation manual install the software up to Procedure No 9 2 When the window shown in Figure 10 of Procedure No 9 page 7 in the installation manual is displayed select AJ PCD35 P2 drive PCle driver and then click OK 3 The warning box may be displayed in such a case click Continue Anyway The warning box may be displayed two or more times 4 In accordance with the instructions on the screen complete the installation and restart the personal computer 14 lt Notes gt f a panel not described in this manual is displayed during installation click Cancel or Complete to close it When connecting a second additional unit install the PCI Express driver once more following the same procedures 3 Confirmation of installation of the PCI Express driver When checking that the PCI Express driver is properly installed be sure to connect the appropriate device to the personal computer Devices not connected to the personal computer cannot be checked using the following method For Windows Vista Business select Start Control Panel System Click on Device Manager For Windows XP Professional select Start Control Panel System The System Properties window appears Select the Hardware tab then c
7. CD35 folder Double click PCD35Driver dmg in the AJ PCD35 folder Double click PCD35Driver pkg Nn RWS NN When driver installation starts follow the instructions on the installation screen lt Notes gt By installing this driver it is possible to connect to this unit to the Macintosh using PCI Express to transfer data at a higher rate When the P2 card is removed drag the icon for the P2 card to Trash and confirm that the P2 card icon disappears before executing removal Reinsert the P2 card if the P2 card icon is not displayed lt Reference gt Occasionally a message regarding Device Removal may be displayed when the P2 drive is connected and the Macintosh is turned on The same message may also be displayed when reinserting the P2 card because the P2 card icon is not displayed but this is not a malfunction Click OK and proceed to use the card 16 Specifications AC adapter DC 16 V 0 6 A when used with AC adapter DC 12 V 0 8 A Power Source when mounted in a personal computer AC 100 240 V 1 20 A 50 60 Hz Power Output indicates safety information DC 16 0 V 3 75 A External dimensions W x H x D indicates safety information 148 4 mm x 42 5 mm x 199 5 mm 5 7 8 inches x 1 11 16 inches x 7 7 8 inches excluding protruding parts Weight 1 2 kg 2 6 Ib Environmenta
8. Cservice us panasonic com Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario LAW 2T3 Tel 905 624 5010 Panasonic de M xico S A De C V Casa Matriz Moras No 313 Col Tlacoquemecatl Del Valle Del Benito Juarez M xico D F C P 03200 Tel 55 5488 1000 Fax 55 5575 6783 Panasonic Latin America S A P O Box 0816 03164 Panama Republic of Panama Tel 507 229 2955 Fax 507 229 5352 Panasonic do Brasil Ltda Rua Cubat o 320 6 andar Paraiso CEP 04013 001 S o Paulo SP Tel 11 3889 4000 Fax 11 3889 4004 Professional amp Broadcast IT Systems Business Unit Europe Panasonic AVC Systems Europe a Division of Panasonic Marketing Europe GmbH Hagenauer Str 43 65203 Wiesbaden Biebrich Deutschland Tel 49 611 235 481 Panasonic Systems Asia Pacific Broadcast Regional Operation Center 2 Jalan Kilang Barat Panasonic Building Singapore 159346 Tel 65 6270 0110 Panasonic Corporation 2008 F E
9. Panasonic Operating Instructions Memory Card Drive wano AJ PCD35P vaino AJ PCD35E Before operating this product please read the instructions carefully and save this manual for future use ENGLISH F1108TO F gt Printed in Japan VQT1X46 Read this first For AJ PCD35P and AJ PCD35E WARNING TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD KEEP THIS EQUIPMENT AWAY FROM ALL LIQUIDS USE AND STORE ONLY IN LOCATIONS WHICH ARE NOT EXPOSED TO THE RISK OF DRIPPING OR SPLASHING LIQUIDS AND DO NOT PLACE ANY LIQUID CONTAINERS ON TOP OF THE EQUIPMENT CAUTION TO REDUCE THE RISK OF FIRE OR SHOCK HAZARD AND ANNOYING INTERFERENCE USE THE RECOMMENDED ACCESSORIES ONLY CAUTION THE MAINS PLUG OF THE POWER SUPPLY CORD SHALL REMAIN READILY OPERABLE THE AC RECEPTACLE MAINS SOCKET OUTLET SHALL BE INSTALLED NEAR THE EQUIPMENT AND SHALL BE EASILY ACCESSIBLE TO COMPLETELY DISCONNECT THIS EQUIPMENT FROM THE AC MAINS DISCONNECT THE POWER CORD PLUG FROM THE AC RECEPTACLE AC Adapter Disconnect the AC mains plug from the AC mains socket when not in use This apparatus must be earthed To ensure safe operation the three pin plug must be inserted only into a standard three pin power point which is effectively earthed through the normal house hold wiring
10. and writing and deleting of data deleting of data Installation There are two ways to connect the P2 drive to a personal computer Windows Apple Macintosh 1 Using the P2 drive as an external drive connected to a personal computer Windows Apple Macintosh 2 Mounting the P2 drive in a 5 inch bay of a desktop personal computer Windows Installation continue To Connect the P2 drive to a Personal Computer for External Use I 2 Dimples 10 After switching the personal computer off remove the power cord from the personal computer After checking that the personal computer is off remove the cover from the personal computer Insert the PCI Express board included with the P2 drive into the PCI Express connector inside the personal computer AARAAARAAARRORARARAR eeeeeeeee prErzEY eller PCI Express connector for example BMN pp OE pa DAN pa NADI g BAE lt Notes gt Install the PCI Express board with the PCI Express connector Installing with an ordinary PCI connector may cause damage to the personal computer Since the included PCI Express board uses a full height bracket it cannot be installed in a low profile slot Refer to page 11 if you are using Mac Pro 1st Generation Tighten the screws etc to attach the PCI Express board to the personal computer Attach the rubber feet to the dimples on the base of the P2 drive 6 Connect the included PCI
11. e connector About 20 cm Cable stop Put the cable in from above 4 Attach the PCI Express cable with the cable stop on the top of the PCI Express board base plate 5 After passing the PCI Express cable through the slot attaching the PCI Express board insert the PCI Express board into the PCI Express connector inside the personal computer AAAAAAAAAANORARAAAA PCI Express EEE EEE EEEEEEE connector HHHHBHAABAE CO BBBBAA for example lt Notes gt Install the PCI Express board with the PCI Express connector Installing with an ordinary PCI connector may cause damage to the personal computer Since the included PCI Express board uses a full height bracket it cannot be installed in a low profile slot 12 If you are unable to pass the PCI Express cable through the slot on your personal computer the P2 drive cannot be mounted in the 5 inch bay In this case use the P2 drive as an external drive 6 Firmly attach the PCI Express board to the personal computer with the screws etc included with the personal computer The PCI Express cable will extend about 20 cm from the connector to the exterior of the personal computer 7 Connect the PCI Express cable to the PCle interface connector of the PCI Express board After connecting the cable tighten the screws on the connector to firmly attach the connector Bend the cable so that it loosely arcs between the area connected to the board and the notch
12. e that both the P2 drive and the personal computer are switched off when connecting the cable 2 DC IN 16V Socket For external use of the P2 drive connect an AC adapter to this socket 3 DC IN 12V Socket To use the P2 drive mounted in a personal computer connect one of the power supply connectors inside the personal computer to this socket See page 13 lt Note gt Do NOT supply power to both the DC IN 12V socket and DC IN 16V socket at the same time 4 Cable Clamp Use this clamp to secure the AC adapter cable when connecting the P2 drive to a personal computer for external use of the Drive 5 Antitheft Lock A commercially available antitheft cable can be connected to this lock Inserting a P2 Card When inserting a P2 card into the slot in the P2 drive make sure you keep the card horizontal as you ease it in J Forcing the card in on an angle may cause a problem Write protection of P2 Card A P2 card has a write protect switch Setting this switch to PROTECT can prevent writing and AEA S QS deleting of data A Note The write protect switch is not effective when the P2 card is inserted in the P2 drive Make sure you remove the P2 card from the P2 Te drive set the switch then re insert the card in order to effect the switch setting Setting the write Setting the write protect switch to protect switch to PROTECT can this side allows prevent writing
13. e to connect up to 2 units Operation may not be possible with graphic card slots The following environment is recommended for the host computer to make full use of the features of P2 drive A striping configuration using 4 or more hard disk drives is recommended to attain sufficient transfer speed when transferring data to the hard disk drive Parts and their Functions Front Panel 1 2 3 4 1 Power Indicator This indicator lights up in green when the P2 drive is running 2 Status Indicator This indicator blinks in green during access to a P2 card lt Note gt Do not remove the P2 card during access of the card otherwise files may be corrupted or the P2 card may fail 3 Card Slots The P2 drive s card slots are designed for P2 cards The P2 drive does not operate with cards other than P2 cards 4 EJECT Button To remove a P2 card press this button so that the button pops out then press it in again lt Note gt For Macintosh only To remove a P2 card drag the icon of the P2 card to Trash and then press the EJECT button after confirming that the P2 card icon disappears Rear Panel oco PCle VF DC IN 16V DC IN 12V D Fea 1 5 4 2 3 The picture shows the rear panel with its cover removed 1 PCle interface connector This connects a PCI Express cable lt Note gt Ensur
14. e trademarks of Apple Computer Inc of the United States PCI Express and PCle are trademarks of PCI SIG Other names of companies and products are trademarks or registered trademarks of the respective companies In these instructions Microsoft Windows Windows XP Professional and Windows Vista Business are given as Windows Windows XP Professional and Windows Vista Business respectively Similarly in these instructions Macintosh Mac Pro and Mac OS X are given as Macintosh Mac Pro and Mac OS X respectively Similarly in these instructions PCI Express and PCle are given as PCI Express and PCle respectively Before use While AJ PCD35 is connected to the personal computer install the required drivers from the CD ROM For details refer to the install manual and PCI Express Driver for Windows page 14 or PCI Express Driver for Macintosh page 16 in this document The AJ PCD35 may become warm during use but this is not a malfunction When using the AJ PCD35 mounted internally part of the PCI Express cable will extend to the exterior of the personal computer Place the personal computer with the AJ PCD35 internally mounted in an area with sufficient space around the back of the computer Overview The AJ PCD35 hereinafter referred to as P2 drive is a data transfer device that uses a PCI Expres
15. es not display all five card slots Since the P2 drive does not support hot plugging do not insert or remove the PCI Express cable with the personal computer power on While the P2 drive and the personal computer are connected do not insert or remove the unit s AC adapter when the personal computer is on If the personal computer is on with the unit off before turning the unit on turn the personal computer off Pay attention to the items below if you are using Mac Pro 1st Generation Insert the PCI Express board supplied into the slot 1 or 4 in MAC Pro 1st Generation Slot number is for using the number of lanes in a normal condition If you insert the board into the slot 2 or 3 change the number of slot lanes to x4 or x8 before insertion by selecting System gt Library CoreServices Expansion Slot Utility If you use more than x8 lanes of RAID interface card and this device in combination operation speed may be limited due to the setting of the number of lanes 11 Installation continue To Mount the P2 drive in a Personal Computer 5 inch Bay I After switching the personal computer off remove the power cord from the personal computer 2 After checking that the personal computer is off remove the cover from the personal computer 3 Put the PCI Express cable included with the P2 drive through the notch in the board bracket about 20 cm from the cabl
16. ify that it recognises the P2 drive lt Notes gt Use the PCI Express cable included with the P2 drive The unit may not operate properly if a commercially available cable of 2 meters or longer is used Attach the PCI Express cable so that it is not in direct contact with the heat sink fan or fins inside the personal computer In Windows XP or Windows Vista some card slots of the P2 drive may be assigned drive names that have already been assigned to existing networks Reassign network drive names if your personal computer does not display all five card slots Since the P2 drive does not support hot plugging do not insert or remove the PCI Express cable with the personal computer power on Connect after carefully checking the configuration of the PCI Express cable Connecting the ends in reverse will damage internal parts and cause malfunction 13 PCI Express Driver for Windows This driver is for the PCI Express interface for the P2 card on this unit The latest driver information can be viewed at the following website https eww pavc panasonic co jp pro av 1 Before installation System requirements for the PCI Express driver are as follows OS Windows XP Professional SP2 or SP3 Windows Vista Business or higher SP1 RAM 1 GB or more CPU Core 2 Duo 2 GHz or higher is recommended 2 Installation of the PCI Express driver Install the PCI Express driver in accordance with the
17. l conditions Operating temperature 0 C to 40 C 32 F to 104 F Operating humidity 10 to 80 w o condensation Personal Computer System Requirements OS proper operation guaranteed Windows XP Professional SP2 SP3 32 bit Windows Vista Business or higher SP1 32 64 bit Mac OS X 10 4 11 Intel processor Mac OS X 10 5 5 Intel processor Main Memory 1 GB or more is recommended Interface PCI Express Rev1 1 when using the included PCI Express board Card slots PC card Type Il x 5 CardBus compliant Please note that specifications and appearance are subject to change for improvement purpose without notice The latest driver information can be viewed at the following website https eww pavc panasonic co jp pro av 17 Information on Disposal for Users of Waste Electrical amp Electronic Equipment private households This symbol on the products and or accompanying documents means that used electrical and electronic products should not be mixed with general household waste For proper treatment recovery and recycling please take these products to designated collection points where they will be accepted on a free of charge basis Alternatively in some countries you may be able to return your products to your local retailer upon the i purchase of an equivalent new product Disposing of this product correctly will help to save valuable resources and prevent any potential negative effects on hu
18. lick on Device Manager PCI Express Driver for Windows continue Check the following items with Device Manager Panasonic AJ PCD35 is displayed below IDE ATA ATAPI controllers MATSHITA AJ PCD35 1 SCSI Disk Device to MATSHITA AJ PCD35 5 SCSI Disk Device are displayed below Disk drives Bi Device Manager File Action View Help e BE m8 m Computer Ee Disk drives x HDS722525VLAT80 ATA Device w MATSHITA AJ PCD35 1 SCSI Disk Device wa MATSHITA AJ PCD35 2 SCSI Disk Device w MATSHITA AJ PCD35 3 SCSI Disk Device g MATSHITA AJ PCD35 4 SCSI Disk Device MATSHITA AJ PCD35 5 SCSI Disk Device Leg ST3808I5A Display adapters f f3 DVD CD ROM drives m e Floppy drive controllers E ca IDE ATA ATAPI controllers ca ATA Channel 0 c ATA Channel 1 C3 Intel R 82801G ICH7 Family Ultra ATA Storage Controllers 27DF PCI Express L ca Panasonic A PCO35 drivers IEEE 1394 Bus host controllers H 2 Keyboards H A Mice and other pointing devices EE Monitors Network adapters E Portable Devices Y Ports COM amp LPT Processors PCI Express Driver for Macintosh This driver is for the P2 card on this unit The latest driver information can be viewed at the following website https eww pavc panasonic co jp pro av Installation of the PCI Express driver Insert the installation CD Double click the Macintosh folder on the CD Double click the AJ P
19. man health and the environment which could otherwise arise from inappropriate waste handling Please contact your local authority for further details of your nearest designated collection point Penalties may be applicable for incorrect disposal of this waste in accordance with national legislation For business users in the European Union If you wish to discard electrical and electronic equipment please contact your dealer or supplier for further information Information on Disposal in other Countries outside the European Union This symbol is only valid in the European Union If you wish to discard this product please contact your local authorities or dealer and ask for the correct method of disposal Panasonic Broadcast amp Television Systems Company Unit Company of Panasonic Corporation of North America Executive Office One Panasonic Way 4E 7 Secaucus NJ 07094 Tel 201 348 7000 Eastern Zone One Panasonic Way 4E 7 Secaucus NJ 07094 Tel 201 348 7196 Southeast Region Tel 201 392 6151 Western Zone 3330 Cahuenga Blvd W Los Angeles CA 90068 Tel 323 436 3608 Government Marketing Department One Panasonic Way 2E 10 Secaucus NJ 07094 Tel 201 348 7587 Broadcast PARTS INFORMATION amp ORDERING 9 00 a m 5 00 p m EST Tel 800 334 4881 24 Hr Fax 800 334 4880 Emergency after hour parts orders Tel 800 334 4881 e mail PBTSparts us panasonic com TECHNICAL SUPPORT Emergency 24 Hour Service Tel 800 222 0741 e mail PBTS
20. rence in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help The user may find the booklet Something About Interference available from FCC local regional offices helpful FCC Warning To assure continued FCC emission limit compliance follow the attached installation instructions and the user must use only shielded interface cables when connecting to host computer or peripheral devices Also any unauthorized changes or modifications to this equipment could void the user s authority to operate this device NOTIFICATION Canada This class B digital apparatus complies with Canadian ICES 003 Cet appareil num ique de la classe B est conforme a la norme
21. s interface and is designed only for P2 cards The P2 drive is capable of making high speed transfers of clip data shot with a memory card camera recorder for P2 cards to a personal computer Windows Apple Macintosh This device supports not only the transferring and copying of clips recorded on P2 cards but also direct editing Features The P2 drive features five card slots it can be used as either an external or an internal drive only Windows It is capable of high speed data transfer of over 1 0 Gbps The transfer speed varies depending on the file to be transferred the system the application software the P2 card version and other conditions When using a 4 GB or 8 GB P2 card the maximum transfer speed is a total of approximately 800 Mbps Supplied Accessories AJ PCD35P AJ PCD35E AC adapter PCI Express board Mounting screws 8 PCI Express cable Rubber feet 4 NA S A es SAZ For AJ PCD35E For AJ PCD35E continental Europe etc U K CD ROM Driver for P2 P2 card manager dedicated software for the respective P2 devices install manual and operation manual Operating Environment Required for Installation To operate the P2 drive the following environment is required on the host computer Empty slot s full height for the PCI Express 1 or more To mount the each P2 drive in a personal computer 1 empty slot is required It is possibl
Download Pdf Manuals
Related Search