CR-R890-BL : Installation and Operating Instructions
Contents
1. 2 Mounting and WiriNng ii 2 Mounting on Metal Surfaces 3 Technical SpecificationS 3 Feed back sx ieiiceecuvesdeitechene never vseeaeedtecseieeecas 5 ProgrammIing veri 6 Card Code Options i 7 Keypad Communication Format 7 Transfer Limit for 4 bits Buffered Format 8 Display on Card Read eeeeeeeaeee 9 Keypad LOCKOUt u rri ri 9 26 bit Wiegand Card Family Code Setting 10 Reader s InterfacCe ci 10 Check in Supervision ei 11 Buzzer SeCttinG ws asic cence ced in 11 Face Light Intensity ee enna eee 12 Face Light Operation enna 12 Face l ight ColoUr sirena 12 Changing the Installer Code 13 Panic Alarm cs eta 13 Resetting to DefaUlt Le 13 Card Presentation TEeSt Le 14 Warranty bei 14 PosiPin 1 INSTALLATION For PosiPin to function correctly with the access control system some programming may be required in the controller or control panel of the host system For further instructions refer to the appropriate manual Only explanations directly concerning PosiPin s programming will be included in this manual SELECTING AN INSTALLATION SITE e Avoid wiring the PosiPin cables in the same conduit as AC power cables lock power or signal wiring e Reader w2. CHANGING THE INSTALLER CODE Section 200 Default 000000 The Installer Code is used to enter PosiPin s programming mode The Installer Code is six digits long where each digit can be any value from 0 to 9 PANIC ALARM A panic code can be generated and transmitted to the controller by pressing and holding the CLEAR and ENTER keys for 2 seconds 26 bit Wiegand 255 65534 37 bit Wiegand 65535 65534 This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand or Option 2 37 bit Wiegand RESETTING TO DEFAULT To reset PosiPin to factory defaults disconnect its power supply Press and hold the 1 and 2 keys simultaneously while reconnecting its power supply CARD PRESENTATION TEST Present the card to the reader as shown in the figure below Place the card parallel to the PosiPin reader and move it toward the reader until the card code PosiPin 13 displays on the controller screen At this point the card is read decoded data transmitted to the controller and the controller has responded accordingly To read the card again remove and re insert the card into the reader s field WARRANTY The Seller warrants its products to be free from defects in materials and workmanship under normal use for a period of one year Except as specifically stated herein all express or implied warranties whatsoever statutory or otherwise includ
3. 3 Technical SpecificationS 3 Feed back sx ieiiceecuvesdeitechene never vseeaeedtecseieeecas 5 ProgrammIing veri 6 Card Code Options i 7 Keypad Communication Format 7 Transfer Limit for 4 bits Buffered Format 8 Display on Card Read eeeeeeeaeee 9 Keypad LOCKOUt u rri ri 9 26 bit Wiegand Card Family Code Setting 10 Reader s InterfacCe ci 10 Check in Supervision ei 11 Buzzer SeCttinG ws asic cence ced in 11 Face Light Intensity ee enna eee 12 Face Light Operation enna 12 Face l ight ColoUr sirena 12 Changing the Installer Code 13 Panic Alarm cs eta 13 Resetting to DefaUlt Le 13 Card Presentation TEeSt Le 14 Warranty bei 14 PosiPin 1 INSTALLATION For PosiPin to function correctly with the access control system some programming may be required in the controller or control panel of the host system For further instructions refer to the appropriate manual Only explanations directly concerning PosiPin s programming will be included in this manual SELECTING AN INSTALLATION SITE e Avoid wiring the PosiPin cables in the same conduit as AC power cables lock power or signal wiring e Reader wiring must remain a minimum of 30cm 12in away from other wiring such as wiring for AC power computer data
4. I flash remain constant or extinguish depending on the operation PosiPin 5 Confirmation Beep When an operation is successfully entered the reader emits a rapid series of beep tones beep beep beep beep beep Rejection Beep When the system reverts to a previous status or an operation is incorrectly entered the reader emits one long beep tone beeeeeeeeeep PROGRAMMING Ensure that corresponding programming is completed in the control panel or controller connected to the PosiPin To Program 1 Press and hold the CLEAR key for 4 seconds The reader emits a confirmation beep and the green LED illuminates 2 Enter the INSTALLER CODE Press the ENTER key default 000000 Reader emits a confirmation beep and the green LED flashes 3 Enter the 3 digit SECTION Press the ENTER key Reader emits a confirmation beep and the green LED stops flashing 4 Enter the required DATA Press the ENTER key The reader emits a confirmation beep and the green LED flashes 6 Installation Manual 5 To program another section repeat steps 3 and 4 To exit programming mode press and hold the CLEAR key for 4 sec The reader emits a rejection beep and the green LED extinguishes CARD CODE OPTIONS Section 001 Default 3 PosiPin can function as a reader a keypad or as both combined Enter Description 0 Keypad and reader disabled For programming only Reader onl
5. 0 Face Light constant Enter Description 0 Blue Face Light 1 Green Face Light CHANGING THE INSTALLER CODE Section 200 Default 000000 The Installer Code is used to enter PosiPin s programming mode The Installer Code is six digits long where each digit can be any value from 0 to 9 PANIC ALARM A panic code can be generated and transmitted to the controller by pressing and holding the CLEAR and ENTER keys for 2 seconds 26 bit Wiegand 255 65534 37 bit Wiegand 65535 65534 This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand or Option 2 37 bit Wiegand RESETTING TO DEFAULT To reset PosiPin to factory defaults disconnect its power supply Press and hold the 1 and 2 keys simultaneously while reconnecting its power supply CARD PRESENTATION TEST Present the card to the reader as shown in the figure below Place the card parallel to the PosiPin reader and move it toward the reader until the card code PosiPin 13 displays on the controller screen At this point the card is read decoded data transmitted to the controller and the controller has responded accordingly To read the card again remove and re insert the card into the reader s field WARRANTY The Seller warrants its products to be free from defects in materials and workmanship under normal use for a period of one year Exc
6. 4 bits buffered with parity 01 to 11 01 to 10 8 Installation Manual DISPLAY ON CARD READ Section 004 Default 3 PosiPin s response to a card being presented to the reader can be adjusted according to the installation s requirements Enter Description 0 Display on Card Read disabled 1 Red Status LED flashes 2 Green Status LED flashes 3 Red and green Status LEDs flash 4 Face Light flashes 5 Face Light and red Status LED flash 6 Face Light and green Status LED flash 7 Face Light and both Status LEDs flash Select 0 in Face Light Operation see page 12 to enable options 0 to 3 in section 004 or select 1 in Face Light Operation see page 12 to enable options 4 to 7 in section 004 If section 103 page 12 is set to 1 the face light will also flash KEYPAD LOCKOUT Section 005 Default 0 The PosiPin keypad comes with a feature that will lock the keypad for 60 seconds when an installer code is entered incorrectly 3 consecutive times PosiPin 9 Enter Description 0 Keypad Lockout disabled 1 Keypad Lockout enabled 26 BIT WIEGAND CARD FAMILY CODE SETTING Section 006 Default 000 When the keypad is enabled the card s family code must be programmed in order for the keypad to recognize the user s PIN When a user enters a PIN on the keypad PosiPin will aut
7. Keypad Lockout disabled 1 Keypad Lockout enabled 26 BIT WIEGAND CARD FAMILY CODE SETTING Section 006 Default 000 When the keypad is enabled the card s family code must be programmed in order for the keypad to recognize the user s PIN When a user enters a PIN on the keypad PosiPin will automatically add the family code programmed in section 006 to the beginning of the PIN before transmitting the data to the controller Therefore also ensure that all cards to be used with the PosiPin contain the same family code This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand Enter Description 0 to 255 Cards Family Code READER S INTERFACE Section 007 Default 0 The reader component of the PosiPin must be programmed to use the same reader communication format as the controller Enter Description 0 26 bit Wiegand 10 Installation Manual 1 37 bit Wiegand CHECK IN SUPERVISION Section 008 Default 0 This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand or Option 2 37 bit Wiegand When no actions are performed on the PosiPin for a period of time it will communicate its status to the controller every 30 seconds by sending a code to confirm its presence 26 bit Wiegand
8. controller can be programmed to generate an alarm Enter Description 0 Check in Supervision disabled 1 Check in Supervision enabled BUZZER SETTING Section 101 Default 3 The number of beep tones emitted as a response to a card being presented to the reader can be adjusted from 0 disabled to 7 7 rapid beep tones Enter Description Number of beep tones per response 0 to 7 PosiPin 11 FACE LIGHT INTENSITY Section 102 Default 4 The Face Light s illumination can be adjusted according to the installation s requirements from 0 extinguished to 8 brightest Enter Description 0 to 8 Face Light s intensity level FACE LIGHT OPERATION Section 103 Default 0 The Face Light can be set to remain illuminated continually or can follow the Status LEDs state Enter Description O Face Light constant 1 Face Light follows Status LEDs If 0 in section 103 is selected this will override options 4 to 7 in Display on Card Read see page 9 In addition if 1 in section 103 is selected this will override 0 to 3 in Display on Card Read see page 9 FACE LIGHT COLOUR Section 104 Default 0 The Face Light s colour can be blue or green as desired 12 Installation Manual This feature only applies when Face Light Operation programmed in Section 103 is set for Option
9. 255 65535 37 bit Wiegand 65535 65535 If the PosiPin does not communicate its status every 30 seconds the controller can be programmed to generate an alarm Enter Description 0 Check in Supervision disabled 1 Check in Supervision enabled BUZZER SETTING Section 101 Default 3 The number of beep tones emitted as a response to a card being presented to the reader can be adjusted from 0 disabled to 7 7 rapid beep tones Enter Description Number of beep tones per response 0 to 7 PosiPin 11 FACE LIGHT INTENSITY Section 102 Default 4 The Face Light s illumination can be adjusted according to the installation s requirements from 0 extinguished to 8 brightest Enter Description 0 to 8 Face Light s intensity level FACE LIGHT OPERATION Section 103 Default 0 The Face Light can be set to remain illuminated continually or can follow the Status LEDs state Enter Description O Face Light constant 1 Face Light follows Status LEDs If 0 in section 103 is selected this will override options 4 to 7 in Display on Card Read see page 9 In addition if 1 in section 103 is selected this will override 0 to 3 in Display on Card Read see page 9 FACE LIGHT COLOUR Section 104 Default 0 The Face Light s colour can be blue or green as desired 12 Installat
10. ACK Visual Feedback When information is entered on the reader s keypad the red and or green LEDs will I flash remain constant or extinguish depending on the operation PosiPin 5 Confirmation Beep When an operation is successfully entered the reader emits a rapid series of beep tones beep beep beep beep beep Rejection Beep When the system reverts to a previous status or an operation is incorrectly entered the reader emits one long beep tone beeeeeeeeeep PROGRAMMING Ensure that corresponding programming is completed in the control panel or controller connected to the PosiPin To Program 1 Press and hold the CLEAR key for 4 seconds The reader emits a confirmation beep and the green LED illuminates 2 Enter the INSTALLER CODE Press the ENTER key default 000000 Reader emits a confirmation beep and the green LED flashes 3 Enter the 3 digit SECTION Press the ENTER key Reader emits a confirmation beep and the green LED stops flashing 4 Enter the required DATA Press the ENTER key The reader emits a confirmation beep and the green LED flashes 6 Installation Manual 5 To program another section repeat steps 3 and 4 To exit programming mode press and hold the CLEAR key for 4 sec The reader emits a rejection beep and the green LED extinguishes CARD CODE OPTIONS Section 001 Default 3 PosiPin can function as a reader a keypad or a
11. IFICATIONS Input Voltage Typical 13 8Vdc min 11 0Vdc max 14 5Vdc Input Current Typical 65mA 12 5Vdc with card 105mA Consumption Typical 812mW 12 5Vdc with card 1 31mW Frequency Exciter Field 125KHz Pulse Modulated receive low 12 500KHz Receive high 15 625KHz Operating Temp 25 C 13 F to 65 C 149 F Output formats Reader 26 and 37 bit Wiegand Keypad 8 26 and 37 bit Wiegand 4 bit with or without parity and 4 bits buffered with or without parity Cable Distance 152 4m 500ft PosiPin 3 Suggested Cables Indicators Weight Material Dimensions Approvals 4 Installation Manual 22AWG 0 8mm Multi conductor Alpha 5196 5198 18AWG 1 2mm Multi conductor Alpha 5386 5388 Belden 9553 18AWG 6 conductor stranded w overall shield Beeper red LED green LED blue or green Face Light 280g 9 8 oz Black UV resistant ABS plastic 99 5mm 5 75in x 118 5mm 2in x 19 5mm 1in C Compliant to all EU and EFTA countries except Greece according to RTT amp E directives Figure 1 Connection Drawing ads aygeo sapeas OY JE ANM YILI SUI O PAYS Y JIOUUOI JOU OG affanuoI au Je PAYS EY ABUU Aids sepeal au e pejeunua Apeane BUM PISIS OY UM eos GLI Japeas OY 12 40980 SAM PISIS BY JIOUUOI JOU OG SC037 Snes 4617 3924 aJay sajqeo Ile adds alqes Bunnoy raonUOI ago 10 JAOAUOI Y 0OBA LO weerga Bunim indino puebaim FEEDB
12. PIN and Proximity Reader For Access Control Systems CR R885 BL S 6 18 o Installation and Operating Instructions V1 1 wi Position Technology TABLE OF CONTENTS Selecting an Installation Site 2 Mounting and WiriNng ii 2 Mounting on Metal Surfaces 3 Technical SpecificationS 3 Feed back sx ieiiceecuvesdeitechene never vseeaeedtecseieeecas 5 ProgrammIing veri 6 Card Code Options i 7 Keypad Communication Format 7 Transfer Limit for 4 bits Buffered Format 8 Display on Card Read eeeeeeeaeee 9 Keypad LOCKOUt u rri ri 9 26 bit Wiegand Card Family Code Setting 10 Reader s InterfacCe ci 10 Check in Supervision ei 11 Buzzer SeCttinG ws asic cence ced in 11 Face Light Intensity ee enna eee 12 Face Light Operation enna 12 Face l ight ColoUr sirena 12 Changing the Installer Code 13 Panic Alarm cs eta 13 Resetting to DefaUlt Le 13 Card Presentation TEeSt Le 14 Warranty bei 14 PosiPin 1 INSTALLATION For PosiPin to function correctly with the access control system some programming may be required in the controller or control panel of the host system For further instructions refer to the appropriate manual Only explanations directl
13. PosiPin s programming mode The Installer Code is six digits long where each digit can be any value from 0 to 9 PANIC ALARM A panic code can be generated and transmitted to the controller by pressing and holding the CLEAR and ENTER keys for 2 seconds 26 bit Wiegand 255 65534 37 bit Wiegand 65535 65534 This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand or Option 2 37 bit Wiegand RESETTING TO DEFAULT To reset PosiPin to factory defaults disconnect its power supply Press and hold the 1 and 2 keys simultaneously while reconnecting its power supply CARD PRESENTATION TEST Present the card to the reader as shown in the figure below Place the card parallel to the PosiPin reader and move it toward the reader until the card code PosiPin 13 displays on the controller screen At this point the card is read decoded data transmitted to the controller and the controller has responded accordingly To read the card again remove and re insert the card into the reader s field WARRANTY The Seller warrants its products to be free from defects in materials and workmanship under normal use for a period of one year Except as specifically stated herein all express or implied warranties whatsoever statutory or otherwise including without limitation any implied warranty of merchantability and fitness for a particular purpose are expr
14. SIS OY UM eos GLI Japeas OY 12 40980 SAM PISIS BY JIOUUOI JOU OG SC037 Snes 4617 3924 aJay sajqeo Ile adds alqes Bunnoy raonUOI ago 10 JAOAUOI Y 0OBA LO weerga Bunim indino puebaim FEEDBACK Visual Feedback When information is entered on the reader s keypad the red and or green LEDs will I flash remain constant or extinguish depending on the operation PosiPin 5 Confirmation Beep When an operation is successfully entered the reader emits a rapid series of beep tones beep beep beep beep beep Rejection Beep When the system reverts to a previous status or an operation is incorrectly entered the reader emits one long beep tone beeeeeeeeeep PROGRAMMING Ensure that corresponding programming is completed in the control panel or controller connected to the PosiPin To Program 1 Press and hold the CLEAR key for 4 seconds The reader emits a confirmation beep and the green LED illuminates 2 Enter the INSTALLER CODE Press the ENTER key default 000000 Reader emits a confirmation beep and the green LED flashes 3 Enter the 3 digit SECTION Press the ENTER key Reader emits a confirmation beep and the green LED stops flashing 4 Enter the required DATA Press the ENTER key The reader emits a confirmation beep and the green LED flashes 6 Installation Manual 5 To program another section repeat steps 3 and 4 To exit programm
15. TING Section 006 Default 000 When the keypad is enabled the card s family code must be programmed in order for the keypad to recognize the user s PIN When a user enters a PIN on the keypad PosiPin will automatically add the family code programmed in section 006 to the beginning of the PIN before transmitting the data to the controller Therefore also ensure that all cards to be used with the PosiPin contain the same family code This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand Enter Description 0 to 255 Cards Family Code READER S INTERFACE Section 007 Default 0 The reader component of the PosiPin must be programmed to use the same reader communication format as the controller Enter Description 0 26 bit Wiegand 10 Installation Manual 1 37 bit Wiegand CHECK IN SUPERVISION Section 008 Default 0 This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand or Option 2 37 bit Wiegand When no actions are performed on the PosiPin for a period of time it will communicate its status to the controller every 30 seconds by sending a code to confirm its presence 26 bit Wiegand 255 65535 37 bit Wiegand 65535 65535 If the PosiPin does not communicate its status every 30 seconds the
16. Vdc with card 105mA Consumption Typical 812mW 12 5Vdc with card 1 31mW Frequency Exciter Field 125KHz Pulse Modulated receive low 12 500KHz Receive high 15 625KHz Operating Temp 25 C 13 F to 65 C 149 F Output formats Reader 26 and 37 bit Wiegand Keypad 8 26 and 37 bit Wiegand 4 bit with or without parity and 4 bits buffered with or without parity Cable Distance 152 4m 500ft PosiPin 3 Suggested Cables Indicators Weight Material Dimensions Approvals 4 Installation Manual 22AWG 0 8mm Multi conductor Alpha 5196 5198 18AWG 1 2mm Multi conductor Alpha 5386 5388 Belden 9553 18AWG 6 conductor stranded w overall shield Beeper red LED green LED blue or green Face Light 280g 9 8 oz Black UV resistant ABS plastic 99 5mm 5 75in x 118 5mm 2in x 19 5mm 1in C Compliant to all EU and EFTA countries except Greece according to RTT amp E directives Figure 1 Connection Drawing ads aygeo sapeas OY JE ANM YILI SUI O PAYS Y JIOUUOI JOU OG affanuoI au Je PAYS EY ABUU Aids sepeal au e pejeunua Apeane BUM PISIS OY UM eos GLI Japeas OY 12 40980 SAM PISIS BY JIOUUOI JOU OG SC037 Snes 4617 3924 aJay sajqeo Ile adds alqes Bunnoy raonUOI ago 10 JAOAUOI Y 0OBA LO weerga Bunim indino puebaim FEEDBACK Visual Feedback When information is entered on the reader s keypad the red and or green LEDs will
17. ajqeo Ile adds alqes Bunnoy raonUOI ago 10 JAOAUOI Y 0OBA LO weerga Bunim indino puebaim FEEDBACK Visual Feedback When information is entered on the reader s keypad the red and or green LEDs will I flash remain constant or extinguish depending on the operation PosiPin 5 Confirmation Beep When an operation is successfully entered the reader emits a rapid series of beep tones beep beep beep beep beep Rejection Beep When the system reverts to a previous status or an operation is incorrectly entered the reader emits one long beep tone beeeeeeeeeep PROGRAMMING Ensure that corresponding programming is completed in the control panel or controller connected to the PosiPin To Program 1 Press and hold the CLEAR key for 4 seconds The reader emits a confirmation beep and the green LED illuminates 2 Enter the INSTALLER CODE Press the ENTER key default 000000 Reader emits a confirmation beep and the green LED flashes 3 Enter the 3 digit SECTION Press the ENTER key Reader emits a confirmation beep and the green LED stops flashing 4 Enter the required DATA Press the ENTER key The reader emits a confirmation beep and the green LED flashes 6 Installation Manual 5 To program another section repeat steps 3 and 4 To exit programming mode press and hold the CLEAR key for 4 sec The reader emits a rejection beep and the green LED extin
18. ating Instructions V1 1 wi Position Technology TABLE OF CONTENTS Selecting an Installation Site 2 Mounting and WiriNng ii 2 Mounting on Metal Surfaces 3 Technical SpecificationS 3 Feed back sx ieiiceecuvesdeitechene never vseeaeedtecseieeecas 5 ProgrammIing veri 6 Card Code Options i 7 Keypad Communication Format 7 Transfer Limit for 4 bits Buffered Format 8 Display on Card Read eeeeeeeaeee 9 Keypad LOCKOUt u rri ri 9 26 bit Wiegand Card Family Code Setting 10 Reader s InterfacCe ci 10 Check in Supervision ei 11 Buzzer SeCttinG ws asic cence ced in 11 Face Light Intensity ee enna eee 12 Face Light Operation enna 12 Face l ight ColoUr sirena 12 Changing the Installer Code 13 Panic Alarm cs eta 13 Resetting to DefaUlt Le 13 Card Presentation TEeSt Le 14 Warranty bei 14 PosiPin 1 INSTALLATION For PosiPin to function correctly with the access control system some programming may be required in the controller or control panel of the host system For further instructions refer to the appropriate manual Only explanations directly concerning PosiPin s programming will be included in this manual SELECTING AN INSTALLATION SITE e A
19. d 1 Check in Supervision enabled BUZZER SETTING Section 101 Default 3 The number of beep tones emitted as a response to a card being presented to the reader can be adjusted from 0 disabled to 7 7 rapid beep tones Enter Description Number of beep tones per response 0 to 7 PosiPin 11 FACE LIGHT INTENSITY Section 102 Default 4 The Face Light s illumination can be adjusted according to the installation s requirements from 0 extinguished to 8 brightest Enter Description 0 to 8 Face Light s intensity level FACE LIGHT OPERATION Section 103 Default 0 The Face Light can be set to remain illuminated continually or can follow the Status LEDs state Enter Description O Face Light constant 1 Face Light follows Status LEDs If 0 in section 103 is selected this will override options 4 to 7 in Display on Card Read see page 9 In addition if 1 in section 103 is selected this will override 0 to 3 in Display on Card Read see page 9 FACE LIGHT COLOUR Section 104 Default 0 The Face Light s colour can be blue or green as desired 12 Installation Manual This feature only applies when Face Light Operation programmed in Section 103 is set for Option 0 Face Light constant Enter Description 0 Blue Face Light 1 Green Face Light
20. east 1 6 4cm remain between the card reader and the metal on all sides of the card reader TECHNICAL SPECIFICATIONS Input Voltage Typical 13 8Vdc min 11 0Vdc max 14 5Vdc Input Current Typical 65mA 12 5Vdc with card 105mA Consumption Typical 812mW 12 5Vdc with card 1 31mW Frequency Exciter Field 125KHz Pulse Modulated receive low 12 500KHz Receive high 15 625KHz Operating Temp 25 C 13 F to 65 C 149 F Output formats Reader 26 and 37 bit Wiegand Keypad 8 26 and 37 bit Wiegand 4 bit with or without parity and 4 bits buffered with or without parity Cable Distance 152 4m 500ft PosiPin 3 Suggested Cables Indicators Weight Material Dimensions Approvals 4 Installation Manual 22AWG 0 8mm Multi conductor Alpha 5196 5198 18AWG 1 2mm Multi conductor Alpha 5386 5388 Belden 9553 18AWG 6 conductor stranded w overall shield Beeper red LED green LED blue or green Face Light 280g 9 8 oz Black UV resistant ABS plastic 99 5mm 5 75in x 118 5mm 2in x 19 5mm 1in C Compliant to all EU and EFTA countries except Greece according to RTT amp E directives Figure 1 Connection Drawing ads aygeo sapeas OY JE ANM YILI SUI O PAYS Y JIOUUOI JOU OG affanuoI au Je PAYS EY ABUU Aids sepeal au e pejeunua Apeane BUM PISIS OY UM eos GLI Japeas OY 12 40980 SAM PISIS BY JIOUUOI JOU OG SC037 Snes 4617 3924 aJay s
21. ept as specifically stated herein all express or implied warranties whatsoever statutory or otherwise including without limitation any implied warranty of merchantability and fitness for a particular purpose are expressly excluded Because Seller does not install or connect the products and because the products may be used in conjunction with products not manufactured by Seller Seller cannot guarantee the performance of the security system Seller obligation and liability under this warranty is expressly limited to repairing or replacing at Seller s option any product not meeting the specifications In no event shall the Seller be liable 14 Installation Manual to the buyer or any other person for any loss or damages whether direct or indirect consequential or incidental including without limitation any damages for lost profits stolen goods or claims by any other party caused by defective goods or otherwise arising from the improper incorrect or otherwise faulty installation or use of the merchandise sold Notes PosiPin 15 16 Installation Manual Position Technology 780 Boul Industriel St Eustache Qu bec Canada J7R 5V3 Fax 450 491 2509 www postech ca Printed in CANADA 06 2003 PPIN E101 PIN and Proximity Reader For Access Control Systems CR R885 BL S 6 18 o Installation and Operating Instructions V1 1 wi Position Technology TABLE OF CONTENTS Selecting an Installation Site
22. er must be installed in a metal enclosure ensure that the face of the card reader is not covered and that at least 1 6 4cm remain between the card reader and the metal on all sides of the card reader TECHNICAL SPECIFICATIONS Input Voltage Typical 13 8Vdc min 11 0Vdc max 14 5Vdc Input Current Typical 65mA 12 5Vdc with card 105mA Consumption Typical 812mW 12 5Vdc with card 1 31mW Frequency Exciter Field 125KHz Pulse Modulated receive low 12 500KHz Receive high 15 625KHz Operating Temp 25 C 13 F to 65 C 149 F Output formats Reader 26 and 37 bit Wiegand Keypad 8 26 and 37 bit Wiegand 4 bit with or without parity and 4 bits buffered with or without parity Cable Distance 152 4m 500ft PosiPin 3 Suggested Cables Indicators Weight Material Dimensions Approvals 4 Installation Manual 22AWG 0 8mm Multi conductor Alpha 5196 5198 18AWG 1 2mm Multi conductor Alpha 5386 5388 Belden 9553 18AWG 6 conductor stranded w overall shield Beeper red LED green LED blue or green Face Light 280g 9 8 oz Black UV resistant ABS plastic 99 5mm 5 75in x 118 5mm 2in x 19 5mm 1in C Compliant to all EU and EFTA countries except Greece according to RTT amp E directives Figure 1 Connection Drawing ads aygeo sapeas OY JE ANM YILI SUI O PAYS Y JIOUUOI JOU OG affanuoI au Je PAYS EY ABUU Aids sepeal au e pejeunua Apeane BUM PI
23. essly excluded Because Seller does not install or connect the products and because the products may be used in conjunction with products not manufactured by Seller Seller cannot guarantee the performance of the security system Seller obligation and liability under this warranty is expressly limited to repairing or replacing at Seller s option any product not meeting the specifications In no event shall the Seller be liable 14 Installation Manual to the buyer or any other person for any loss or damages whether direct or indirect consequential or incidental including without limitation any damages for lost profits stolen goods or claims by any other party caused by defective goods or otherwise arising from the improper incorrect or otherwise faulty installation or use of the merchandise sold Notes PosiPin 15 16 Installation Manual Position Technology 780 Boul Industriel St Eustache Qu bec Canada J7R 5V3 Fax 450 491 2509 www postech ca Printed in CANADA 06 2003 PPIN E101
24. five digits are entered on the keypad This feature only applies when the format programmed in Section 002 is set for Option 5 4 bits buffered without parity or Option 6 4 bits buffered with parity Enter Description If section 002 is Option 5 4 bits buffered without parity If section 002 is Option 6 4 bits buffered with parity 01 to 11 01 to 10 8 Installation Manual DISPLAY ON CARD READ Section 004 Default 3 PosiPin s response to a card being presented to the reader can be adjusted according to the installation s requirements Enter Description 0 Display on Card Read disabled 1 Red Status LED flashes 2 Green Status LED flashes 3 Red and green Status LEDs flash 4 Face Light flashes 5 Face Light and red Status LED flash 6 Face Light and green Status LED flash 7 Face Light and both Status LEDs flash Select 0 in Face Light Operation see page 12 to enable options 0 to 3 in section 004 or select 1 in Face Light Operation see page 12 to enable options 4 to 7 in section 004 If section 103 page 12 is set to 1 the face light will also flash KEYPAD LOCKOUT Section 005 Default 0 The PosiPin keypad comes with a feature that will lock the keypad for 60 seconds when an installer code is entered incorrectly 3 consecutive times PosiPin 9 Enter Description 0
25. guishes CARD CODE OPTIONS Section 001 Default 3 PosiPin can function as a reader a keypad or as both combined Enter Description 0 Keypad and reader disabled For programming only Reader only enabled A user must 1 presenta valid card to the reader for Access Granted Keypad only enabled A user must enter 2 a valid code on the keypad for Access Granted Keypad and reader enabled A user 3 must present a valid card and enter a valid code for Access Granted KEYPAD COMMUNICATION FORMAT Section 002 Default 1 PosiPin must use the same keypad communication format as the controller Enter Description 0 8 bit Wiegand Motorola ARK 1 26 bit Wiegand default used by Centaur also see section 006 PosiPin 7 2 37 bit Wiegand Not supported by Centaur 3 4 bits without parity 4 4 bits with parity 5 4 bits buffered without parity also see section 003 6 4 bits buffered with parity also see section 003 Note that BCD is not supported TRANSFER LIMIT FOR 4 BITS BUFFERED FORMAT Section 003 Default 00 This feature sets the number of digits retained in memory before the data is sent to the controller For example if section 003 is set at 05 PosiPin will transmit once five digits are entered on the keypad This feature only applies when the format programmed in Section 002
26. in order for the keypad to recognize the user s PIN When a user enters a PIN on the keypad PosiPin will automatically add the family code programmed in section 006 to the beginning of the PIN before transmitting the data to the controller Therefore also ensure that all cards to be used with the PosiPin contain the same family code This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand Enter Description 0 to 255 Cards Family Code READER S INTERFACE Section 007 Default 0 The reader component of the PosiPin must be programmed to use the same reader communication format as the controller Enter Description 0 26 bit Wiegand 10 Installation Manual 1 37 bit Wiegand CHECK IN SUPERVISION Section 008 Default 0 This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand or Option 2 37 bit Wiegand When no actions are performed on the PosiPin for a period of time it will communicate its status to the controller every 30 seconds by sending a code to confirm its presence 26 bit Wiegand 255 65535 37 bit Wiegand 65535 65535 If the PosiPin does not communicate its status every 30 seconds the controller can be programmed to generate an alarm Enter Description 0 Check in Supervision disable
27. ing without limitation any implied warranty of merchantability and fitness for a particular purpose are expressly excluded Because Seller does not install or connect the products and because the products may be used in conjunction with products not manufactured by Seller Seller cannot guarantee the performance of the security system Seller obligation and liability under this warranty is expressly limited to repairing or replacing at Seller s option any product not meeting the specifications In no event shall the Seller be liable 14 Installation Manual to the buyer or any other person for any loss or damages whether direct or indirect consequential or incidental including without limitation any damages for lost profits stolen goods or claims by any other party caused by defective goods or otherwise arising from the improper incorrect or otherwise faulty installation or use of the merchandise sold Notes PosiPin 15 16 Installation Manual Position Technology 780 Boul Industriel St Eustache Qu bec Canada J7R 5V3 Fax 450 491 2509 www postech ca Printed in CANADA 06 2003 PPIN E101 PIN and Proximity Reader For Access Control Systems CR R885 BL S 6 18 o Installation and Operating Instructions V1 1 wi Position Technology TABLE OF CONTENTS Selecting an Installation Site 2 Mounting and WiriNng ii 2 Mounting on Metal Surfaces
28. ing mode press and hold the CLEAR key for 4 sec The reader emits a rejection beep and the green LED extinguishes CARD CODE OPTIONS Section 001 Default 3 PosiPin can function as a reader a keypad or as both combined Enter Description 0 Keypad and reader disabled For programming only Reader only enabled A user must 1 presenta valid card to the reader for Access Granted Keypad only enabled A user must enter 2 a valid code on the keypad for Access Granted Keypad and reader enabled A user 3 must present a valid card and enter a valid code for Access Granted KEYPAD COMMUNICATION FORMAT Section 002 Default 1 PosiPin must use the same keypad communication format as the controller Enter Description 0 8 bit Wiegand Motorola ARK 1 26 bit Wiegand default used by Centaur also see section 006 PosiPin 7 2 37 bit Wiegand Not supported by Centaur 3 4 bits without parity 4 4 bits with parity 5 4 bits buffered without parity also see section 003 6 4 bits buffered with parity also see section 003 Note that BCD is not supported TRANSFER LIMIT FOR 4 BITS BUFFERED FORMAT Section 003 Default 00 This feature sets the number of digits retained in memory before the data is sent to the controller For example if section 003 is set at 05 PosiPin will transmit once
29. ion Manual This feature only applies when Face Light Operation programmed in Section 103 is set for Option 0 Face Light constant Enter Description 0 Blue Face Light 1 Green Face Light CHANGING THE INSTALLER CODE Section 200 Default 000000 The Installer Code is used to enter PosiPin s programming mode The Installer Code is six digits long where each digit can be any value from 0 to 9 PANIC ALARM A panic code can be generated and transmitted to the controller by pressing and holding the CLEAR and ENTER keys for 2 seconds 26 bit Wiegand 255 65534 37 bit Wiegand 65535 65534 This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand or Option 2 37 bit Wiegand RESETTING TO DEFAULT To reset PosiPin to factory defaults disconnect its power supply Press and hold the 1 and 2 keys simultaneously while reconnecting its power supply CARD PRESENTATION TEST Present the card to the reader as shown in the figure below Place the card parallel to the PosiPin reader and move it toward the reader until the card code PosiPin 13 displays on the controller screen At this point the card is read decoded data transmitted to the controller and the controller has responded accordingly To read the card again remove and re insert the card into the reader s field WARRANTY The Seller warrants i
30. iring must remain a minimum of 30cm 12in away from other wiring such as wiring for AC power computer data telephones electric locks etc eAvoid sites within 1 1m 3 5ft of computer monitors or CRTs e Avoid sites near sources of broad spectrum EMI noise such as motors pumps generators DC to AC converters AC switching relays power supplies and light dimmers e Avoid sites near potential sources of RF signals such as cellular phones two way radios etc MOUNTING AND WIRING After selecting a site for the PosiPin use the mounting plate as a guide to drill two holes to secure the mounting plate and a hole for the cable 0 95cm to 2 54cm 0 375in to 1in wide Place a grommet around the edge of the hole for the cable Prepare PosiPin s cable by cutting the cable jacket back 3 175cm 1 25in and stripping the wires back 2 Installation Manual 0 635cm 0 25in Splice PosiPin s wires with a recommended cable wire Route the cable to the controller and connect as shown in Figure 1 Connection Drawing on page 5 MOUNTING ON METAL SURFACES Although the read range may slightly decrease PosiPin can be mounted on metal However do not box in or surround the card reader with any kind of metal If the reader must be installed in a metal enclosure ensure that the face of the card reader is not covered and that at least 1 6 4cm remain between the card reader and the metal on all sides of the card reader TECHNICAL SPEC
31. is set for Option 5 4 bits buffered without parity or Option 6 4 bits buffered with parity Enter Description If section 002 is Option 5 4 bits buffered without parity If section 002 is Option 6 4 bits buffered with parity 01 to 11 01 to 10 8 Installation Manual DISPLAY ON CARD READ Section 004 Default 3 PosiPin s response to a card being presented to the reader can be adjusted according to the installation s requirements Enter Description 0 Display on Card Read disabled 1 Red Status LED flashes 2 Green Status LED flashes 3 Red and green Status LEDs flash 4 Face Light flashes 5 Face Light and red Status LED flash 6 Face Light and green Status LED flash 7 Face Light and both Status LEDs flash Select 0 in Face Light Operation see page 12 to enable options 0 to 3 in section 004 or select 1 in Face Light Operation see page 12 to enable options 4 to 7 in section 004 If section 103 page 12 is set to 1 the face light will also flash KEYPAD LOCKOUT Section 005 Default 0 The PosiPin keypad comes with a feature that will lock the keypad for 60 seconds when an installer code is entered incorrectly 3 consecutive times PosiPin 9 Enter Description 0 Keypad Lockout disabled 1 Keypad Lockout enabled 26 BIT WIEGAND CARD FAMILY CODE SET
32. omatically add the family code programmed in section 006 to the beginning of the PIN before transmitting the data to the controller Therefore also ensure that all cards to be used with the PosiPin contain the same family code This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand Enter Description 0 to 255 Cards Family Code READER S INTERFACE Section 007 Default 0 The reader component of the PosiPin must be programmed to use the same reader communication format as the controller Enter Description 0 26 bit Wiegand 10 Installation Manual 1 37 bit Wiegand CHECK IN SUPERVISION Section 008 Default 0 This feature only applies when the communication format programmed in Section 002 is set for Option 1 26 bit Wiegand or Option 2 37 bit Wiegand When no actions are performed on the PosiPin for a period of time it will communicate its status to the controller every 30 seconds by sending a code to confirm its presence 26 bit Wiegand 255 65535 37 bit Wiegand 65535 65535 If the PosiPin does not communicate its status every 30 seconds the controller can be programmed to generate an alarm Enter Description 0 Check in Supervision disabled 1 Check in Supervision enabled BUZZER SETTING Section 101 Default 3 The numbe
33. r Description If section 002 is Option 5 4 bits buffered without parity If section 002 is Option 6 4 bits buffered with parity 01 to 11 01 to 10 8 Installation Manual DISPLAY ON CARD READ Section 004 Default 3 PosiPin s response to a card being presented to the reader can be adjusted according to the installation s requirements Enter Description 0 Display on Card Read disabled 1 Red Status LED flashes 2 Green Status LED flashes 3 Red and green Status LEDs flash 4 Face Light flashes 5 Face Light and red Status LED flash 6 Face Light and green Status LED flash 7 Face Light and both Status LEDs flash Select 0 in Face Light Operation see page 12 to enable options 0 to 3 in section 004 or select 1 in Face Light Operation see page 12 to enable options 4 to 7 in section 004 If section 103 page 12 is set to 1 the face light will also flash KEYPAD LOCKOUT Section 005 Default 0 The PosiPin keypad comes with a feature that will lock the keypad for 60 seconds when an installer code is entered incorrectly 3 consecutive times PosiPin 9 Enter Description 0 Keypad Lockout disabled 1 Keypad Lockout enabled 26 BIT WIEGAND CARD FAMILY CODE SETTING Section 006 Default 000 When the keypad is enabled the card s family code must be programmed
34. r of beep tones emitted as a response to a card being presented to the reader can be adjusted from 0 disabled to 7 7 rapid beep tones Enter Description Number of beep tones per response 0 to 7 PosiPin 11 FACE LIGHT INTENSITY Section 102 Default 4 The Face Light s illumination can be adjusted according to the installation s requirements from 0 extinguished to 8 brightest Enter Description 0 to 8 Face Light s intensity level FACE LIGHT OPERATION Section 103 Default 0 The Face Light can be set to remain illuminated continually or can follow the Status LEDs state Enter Description O Face Light constant 1 Face Light follows Status LEDs If 0 in section 103 is selected this will override options 4 to 7 in Display on Card Read see page 9 In addition if 1 in section 103 is selected this will override 0 to 3 in Display on Card Read see page 9 FACE LIGHT COLOUR Section 104 Default 0 The Face Light s colour can be blue or green as desired 12 Installation Manual This feature only applies when Face Light Operation programmed in Section 103 is set for Option 0 Face Light constant Enter Description 0 Blue Face Light 1 Green Face Light CHANGING THE INSTALLER CODE Section 200 Default 000000 The Installer Code is used to enter
35. s both combined Enter Description 0 Keypad and reader disabled For programming only Reader only enabled A user must 1 presenta valid card to the reader for Access Granted Keypad only enabled A user must enter 2 a valid code on the keypad for Access Granted Keypad and reader enabled A user 3 must present a valid card and enter a valid code for Access Granted KEYPAD COMMUNICATION FORMAT Section 002 Default 1 PosiPin must use the same keypad communication format as the controller Enter Description 0 8 bit Wiegand Motorola ARK 1 26 bit Wiegand default used by Centaur also see section 006 PosiPin 7 2 37 bit Wiegand Not supported by Centaur 3 4 bits without parity 4 4 bits with parity 5 4 bits buffered without parity also see section 003 6 4 bits buffered with parity also see section 003 Note that BCD is not supported TRANSFER LIMIT FOR 4 BITS BUFFERED FORMAT Section 003 Default 00 This feature sets the number of digits retained in memory before the data is sent to the controller For example if section 003 is set at 05 PosiPin will transmit once five digits are entered on the keypad This feature only applies when the format programmed in Section 002 is set for Option 5 4 bits buffered without parity or Option 6 4 bits buffered with parity Ente
36. telephones electric locks etc eAvoid sites within 1 1m 3 5ft of computer monitors or CRTs e Avoid sites near sources of broad spectrum EMI noise such as motors pumps generators DC to AC converters AC switching relays power supplies and light dimmers e Avoid sites near potential sources of RF signals such as cellular phones two way radios etc MOUNTING AND WIRING After selecting a site for the PosiPin use the mounting plate as a guide to drill two holes to secure the mounting plate and a hole for the cable 0 95cm to 2 54cm 0 375in to 1in wide Place a grommet around the edge of the hole for the cable Prepare PosiPin s cable by cutting the cable jacket back 3 175cm 1 25in and stripping the wires back 2 Installation Manual 0 635cm 0 25in Splice PosiPin s wires with a recommended cable wire Route the cable to the controller and connect as shown in Figure 1 Connection Drawing on page 5 MOUNTING ON METAL SURFACES Although the read range may slightly decrease PosiPin can be mounted on metal However do not box in or surround the card reader with any kind of metal If the reader must be installed in a metal enclosure ensure that the face of the card reader is not covered and that at least 1 6 4cm remain between the card reader and the metal on all sides of the card reader TECHNICAL SPECIFICATIONS Input Voltage Typical 13 8Vdc min 11 0Vdc max 14 5Vdc Input Current Typical 65mA 12 5
37. ts products to be free from defects in materials and workmanship under normal use for a period of one year Except as specifically stated herein all express or implied warranties whatsoever statutory or otherwise including without limitation any implied warranty of merchantability and fitness for a particular purpose are expressly excluded Because Seller does not install or connect the products and because the products may be used in conjunction with products not manufactured by Seller Seller cannot guarantee the performance of the security system Seller obligation and liability under this warranty is expressly limited to repairing or replacing at Seller s option any product not meeting the specifications In no event shall the Seller be liable 14 Installation Manual to the buyer or any other person for any loss or damages whether direct or indirect consequential or incidental including without limitation any damages for lost profits stolen goods or claims by any other party caused by defective goods or otherwise arising from the improper incorrect or otherwise faulty installation or use of the merchandise sold Notes PosiPin 15 16 Installation Manual Position Technology 780 Boul Industriel St Eustache Qu bec Canada J7R 5V3 Fax 450 491 2509 www postech ca Printed in CANADA 06 2003 PPIN E101 PIN and Proximity Reader For Access Control Systems CR R885 BL S 6 18 o Installation and Oper
38. void wiring the PosiPin cables in the same conduit as AC power cables lock power or signal wiring e Reader wiring must remain a minimum of 30cm 12in away from other wiring such as wiring for AC power computer data telephones electric locks etc eAvoid sites within 1 1m 3 5ft of computer monitors or CRTs e Avoid sites near sources of broad spectrum EMI noise such as motors pumps generators DC to AC converters AC switching relays power supplies and light dimmers e Avoid sites near potential sources of RF signals such as cellular phones two way radios etc MOUNTING AND WIRING After selecting a site for the PosiPin use the mounting plate as a guide to drill two holes to secure the mounting plate and a hole for the cable 0 95cm to 2 54cm 0 375in to 1in wide Place a grommet around the edge of the hole for the cable Prepare PosiPin s cable by cutting the cable jacket back 3 175cm 1 25in and stripping the wires back 2 Installation Manual 0 635cm 0 25in Splice PosiPin s wires with a recommended cable wire Route the cable to the controller and connect as shown in Figure 1 Connection Drawing on page 5 MOUNTING ON METAL SURFACES Although the read range may slightly decrease PosiPin can be mounted on metal However do not box in or surround the card reader with any kind of metal If the reader must be installed in a metal enclosure ensure that the face of the card reader is not covered and that at l
39. y concerning PosiPin s programming will be included in this manual SELECTING AN INSTALLATION SITE e Avoid wiring the PosiPin cables in the same conduit as AC power cables lock power or signal wiring e Reader wiring must remain a minimum of 30cm 12in away from other wiring such as wiring for AC power computer data telephones electric locks etc eAvoid sites within 1 1m 3 5ft of computer monitors or CRTs e Avoid sites near sources of broad spectrum EMI noise such as motors pumps generators DC to AC converters AC switching relays power supplies and light dimmers e Avoid sites near potential sources of RF signals such as cellular phones two way radios etc MOUNTING AND WIRING After selecting a site for the PosiPin use the mounting plate as a guide to drill two holes to secure the mounting plate and a hole for the cable 0 95cm to 2 54cm 0 375in to 1in wide Place a grommet around the edge of the hole for the cable Prepare PosiPin s cable by cutting the cable jacket back 3 175cm 1 25in and stripping the wires back 2 Installation Manual 0 635cm 0 25in Splice PosiPin s wires with a recommended cable wire Route the cable to the controller and connect as shown in Figure 1 Connection Drawing on page 5 MOUNTING ON METAL SURFACES Although the read range may slightly decrease PosiPin can be mounted on metal However do not box in or surround the card reader with any kind of metal If the read
40. y enabled A user must 1 presenta valid card to the reader for Access Granted Keypad only enabled A user must enter 2 a valid code on the keypad for Access Granted Keypad and reader enabled A user 3 must present a valid card and enter a valid code for Access Granted KEYPAD COMMUNICATION FORMAT Section 002 Default 1 PosiPin must use the same keypad communication format as the controller Enter Description 0 8 bit Wiegand Motorola ARK 1 26 bit Wiegand default used by Centaur also see section 006 PosiPin 7 2 37 bit Wiegand Not supported by Centaur 3 4 bits without parity 4 4 bits with parity 5 4 bits buffered without parity also see section 003 6 4 bits buffered with parity also see section 003 Note that BCD is not supported TRANSFER LIMIT FOR 4 BITS BUFFERED FORMAT Section 003 Default 00 This feature sets the number of digits retained in memory before the data is sent to the controller For example if section 003 is set at 05 PosiPin will transmit once five digits are entered on the keypad This feature only applies when the format programmed in Section 002 is set for Option 5 4 bits buffered without parity or Option 6 4 bits buffered with parity Enter Description If section 002 is Option 5 4 bits buffered without parity If section 002 is Option 6
Download Pdf Manuals
Related Search