VIP X16 XF E: Installation Manual
Contents
1. Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 20 en Configuration VIP X16 XF E 6 Configuration 6 1 Setup Before you can operate the unit within your network it must have a valid IP address for your network and a compatible subnet mask NOTICE As a default DHCP is enabled in the unit s network settings With an active DHCP server in the network you must know the IP address assigned by the DHCP server to operate the unit The following default address is preset at the factory 192 168 0 1 The setup procedure is carried out via Bosch Video Client or other management systems All information regarding the configuration can be found in the relevant documentation of the video management system in use 6 2 Setup using Bosch Video Client For the current version of the Bosch Video Client BVC management software access your Bosch product catalog on the Internet This program allows you to implement and set up the unit in the network quickly and conveniently Installing the program 1 Download Bosch Video Client from the Bosch product catalog on the Internet 2 Unzip the file 3 Double click the installer file 4 Follow the instructions on the screen to complete the installation Configuring the unit You can start Bosch Video Client immediately after installation 1 Double click the ERA icon on the desktop to start the program Alternatively start the application vi2. The cable connection between the serial interface and the connected unit is not correct Check all cable connections and ensure all plugs are properly fitted The interface parameters do not match those of the other unit connected Make sure that the settings of all units involved are compatible F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E Troubleshooting en 23 Malfunction Possible causes Recommended solution The unit is not Power failure during Have the unit checked by operational after a programming by firmware file Customer Service and replace it firmware upload if necessary Incorrect firmware file Enter the IP address of the unit followed by main htm in your Web browser and repeat the upload Placeholder with a red JVM not installed on your Install Sun JVM from the Bosch cross instead of the computer or not activated product catalog on the Internet ActiveX components Web browser contains Active proxy server in network Create a rule in the local empty fields computer s proxy settings to exclude local IP addresses The STATUS LED flashes Firmware upload failed Repeat firmware upload 7 3 Malfunctions with iSCSI connections Malfunction Possible causes Recommended solution After connecting to the Incorrect LUN mapping during Check the iSCSI system iSCSI target no LUNs are i
3. 5 5 Vp p max input voltage microphone amplifier 60 dB max 1 line out 3 0 Vp p typ output voltage at 10 kohm impedance The stereo plug must be connected as follows Contact AUDIO IN AUDIO OUT Tip Channel 1 Channel 1 Middle ring Channel 2 Lower ring Ground Ground 1 Connect an audio source to the AUDIO IN socket with a 3 5 mm 1 8 in stereo plug 2 Connect an audio receiver with line in connection to the AUDIO OUT socket with a 3 5 mm 1 8 in stereo plug Note that the audio function is not activated by default To use audio connections activate the corresponding setting when configuring the unit 5 4 Connecting alarm inputs and relay output Alarm inputs The VIP X16 XF E encoder has four alarm inputs on the terminal block The alarm inputs are used to connect to external alarm devices such as door contacts or sensors With the appropriate configuration an alarm sensor can automatically connect the VIP X16 XF E encoder to a remote location for example Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 18 en Connection VIP X16 XF E A zero potential closing contact or switch can be used as the actuator If possible use a bounce free contact system as the actuator CAUTION Please observe the labeling on the unit 1 Connectthe lines to the appropriate terminals on the terminal block IN1 to IN4 and check that the connectio
4. 1 8 2 8 3 Maintenance Updates Firmware updates are carried out via Bosch Video Client or other management systems in use Please refer to the relevant documentation Factory reset You can use the factory reset button to restore the unit to its original settings Any changes to the settings are overwritten by the factory defaults A reset may be necessary for example if the unit has invalid settings that prevent it from functioning as desired 1 All configured settings will be discarded during a reset If necessary back up the current configuration beforehand Enter the IP address of the unit as URL in the Web browser and use the Download button on the SETTINGS gt Advanced Mode gt Service gt Maintenance configuration page 2 Using a pointed object press the factory reset button located on the front panel until the STATUS LED flashes All settings will revert to their defaults 3 The unit is ready for use as soon as the CONNECT LED lights up 4 See the relevant chapter in this manual for information on configuration of the unit Further topics Section 3 4 Connections controls and displays page 11 Section 6 Configuration page 20 Repairs Never open the housing of the unit The unit does not contain any user serviceable parts Ensure that all maintenance or repair work is carried out only by qualified personnel electrical engineers or network technology specialists In case of doubt contact your
5. 4CIF resolution the first stream with full frame rate and the second stream with lower frame rate This allows viewing and recording at two different quality levels to save disk space and bandwidth F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E System overview en 9 Video encoding The VIP X16 XF E High Profile encoder uses the H 264 video compression standard Thanks to efficient encoding the data rate remains low even with high image quality and can also be adapted to local conditions within wide limits Audio encoding The VIP X16 XF E encoder uses the G 711 AAC and L16 audio compression standards G 711 is the default setting for live transmission For recording the default setting is AAC When configuring with a Web browser you can select your preferred standard for recording Using video management systems this is also true for live audio Viewing View the VIP X16 XF E encoder video on a PC using a Web browser or Bosch Video Client in the Bosch Video Management System or integrate it into another video management system By routing the IP video to a high performance VIP XD HD video decoder you can present the video with ultimate clarity Recording You can record each video input independently on different media Thus video can be recorded centrally on iSCSI drives managed by VRM Video Recording Manager The encoder features a highly flexible recording scheduler prov
6. changes Four alarm inputs and one relay output Built in video sensor for motion alarms Event controlled automatic connection Convenient maintenance via uploads Flexible encryption of control and data channels Authentication according to international standard 802 1x Bidirectional audio mono for line connections Audio encoding to international standards AAC G 711 and L16 F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E System overview en 11 3 4 Connections controls and displays 3 4 1 Front view 1 Factory reset button to restore factory default settings 2 LED ACTIVITY flashes during data transmission 3 LED LINK lights up when the unit is connected to the network 4 LED STATUS lights up during startup 5 LED CONNECT lights up when supplied with power after startup Further topics Section 7 4 LEDs page 23 Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 12 en System overview VIP X16 XF E 3 4 2 Rear view QA OO OO OO OLLEELLE A JI 1 VIDEO IN 1 to 16 video inputs BNC socket for connecting the video source 2 ETH RJ45 socket for connecting to an Ethernet LAN local network 10 100 1000 MBit Base T 3 AUDIO IN audio connection mono 3 5 mm 1 8 in stereo socket audio in for connecting two audio sources 4 Terminal block for alarm inputs relay output and serial interface 5 AUDIO OUT audio connection mon
7. dealer s technical service center F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E Setting out of order en 27 9 Setting out of order 9 1 Transfer and disposal The VIP X16 XF E encoder should only be passed on together with this installation manual Your Bosch product is designed and manufactured with high quality materials and components which can be recycled and reused This symbol means that electrical and electronic equipment at their end of life should be disposed of separately from your household waste In the European Union there are separate collection systems for used electrical and electronic products Please dispose of this equipment at your local community waste collection recycling center Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 28 en Technical data VIP X16 XF E 10 10 1 10 2 10 3 10 4 Technical data Electrical Input voltage Input current Power consumption Connectors Mechanical Dimensions H x W xD Weight Video Audio Signal line in Signal line out Ethernet COM port Alarm Relay Display 100 to 240 V AC 47 to 63 Hz 0 32 to0 15A 16 W IEC 320 C14 44 x 443 x 157 mm 1 732 x 17 441 x 6 181 in without brackets including BNC sockets Approx 1 7 kg 3 7 Ib 16 x BNC socket 75 ohm terminated Analog composite 0 7 to 1 2 Vp p NTSC or PAL 2 x 3 5 mm 1 8 in
8. information to help you when troubleshooting or fine tuning the unit The values indicate the proportions of the individual functions on the coder load shown as percentages gt Move the cursor over the graphic indicator Some additional numerical values are also displayed Network connection la BOSCH You can display information about the network connection To do this move the cursor over Link Ethernet link type UL Uplink speed of the outgoing data traffic DL Downlink speed of the incoming data traffic Terminal block The terminal block has several contacts for Serial data transmission 4alarm inputs 1 relay output Pin assignment serial interface Options for using the serial interface include transferring transparent data controlling connected units or operating the unit with a terminal program The serial interface supports the RS 232 RS 422 and RS 485 transmission standards The mode used depends on the current configuration The pin assignment of the serial interface depends on the interface mode used Contact RS 232 mode RS 422 mode RS 485 mode CTS RxD receive data minus TXD TxD transmit data TxD transmit data minus Data RTS TxD transmit data plus Data F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E Troubleshooting en 25 Contac
9. stereo socket 2 x mono in microphone line 1 x mono line out 9 kohm typical 5 5 Vp p max microphone amplifier 60 dB max 3 0 Vp p at 10 kohm typical 10 100 1000 Base T auto sensing half full duplex RJ45 1 x RS 232 RS 422 RS 485 bidirectional push in terminal 4 x push in terminal input non isolated closing contact activation resistance 10 ohm max 1 x push in terminal output 30 Vp p SELV 0 2 A 4 x LED ACTIVITY LINK STATUS CONNECT on the front panel 2 x LED data transfer network connection on the rear panel Environmental conditions Operating temperature Storage temperature Relative humidity Thermal value 0 C to 50 C 32 F to 122 F 0 C to 50 C 32 F to 122 F 0 to 95 atmospheric humidity non condensing 55 BTU h max Certifications and approvals Safety System IEC 60950 IEC 62676 2 EN50132 5 2 F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH Technical data en 29 Electromagnetic compatibility Approvals Standards Video standards Video coding protocols Video data rates Connections Image resolutions PAL NTSC GOP structure Total delay Dual Streaming Frame rate Audio standards Audio frequency rate Audio sampling rate Audio data rate Signal to noise ratio Network protocols Encryption EN55103 1 EN55103 2 EN50130 4 EN50121 4 EN55022 EN55024 EN61000 3 2 EN61000 3 3 FCC 4
10. 7 CFR Part 15 Subpart B Class B AS NZS 3548 Class B CE UL PAL NTSC H 264 High Profile ISO IEC 14496 10 M JPEG 9 6 kbps to 2 Mbps per channel 16 simultaneous unicast multicast ACIF 704 x 576 480 I IP 260 ms typical Full performance on first stream limited frame rate on second stream 1 to 25 30 ips PAL NTSC G 711 L16 AAC LC G 711 300 Hz to 3 4 kHz L16 300 Hz to 6 4 kHz AAC LC 300 Hz to 6 4 kHz G 711 8 kHz L16 16 kHz AAC LC 16 kHz G 711 80 kbps L16 640 kbps AAC LC 48 kbps gt 50 dB IPv4 IPv6 UDP TCP HTTP HTTPS RTP IGMP V2 V3 ICMP RTSP FTP Telnet ARP DHCP SNTP 802 1x SMTP iSCSI UPnP SSDP TLS 1 0 SSL AES licensed option Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 30 en Technical data VIP X16 XFE F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH Bosch Sicherheitssysteme GmbH Robert Bosch Ring 5 85630 Grasbrunn Germany www boschsecurity com Bosch Sicherheitssysteme GmbH 2012
11. SCSI system configuration configuration and reconnect displayed After connecting to the The LUN list could not be read Check the iSCSI system iSCSI target LUN FAIL as it was assigned to the wrong configuration and reconnect appears below a node network interface LUN mapping is not Some iSCSI systems do not Delete the initiator extension possible support the use of an initiator extension 7 4 LEDs The VIP X16 XF E encoder has LEDs on its front and rear panels that show the operating status and can give indications of possible malfunctions ACTIVITY LED Flashes LINK LED Lights up STATUS LED Lights up Flashes CONNECT LED Lights up Flashes Traffic on the network Network connection established Startup in progress The unit is faulty for example following failed firmware upload The unit is switched on and startup completed Video connection active Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 24 en Troubleshooting VIP X16 XF E 7 5 7 6 7 7 RJ45 socket LEDs Left LED flashes as ACTIVITY Traffic on the network LED Right LED lights up as LINK Network connection established LED Processor load If the VIP X16 XF E encoder is accessed via the Web browser you will see the processor load indicator bar in the top right of the window next to the information icon T lo BOSCH You can obtain additional
12. VIP X16 XF E VIP X16XF E BOSCH en Installation Manual VIP X16 XF E Table of Contents en 3 Table of Contents 1 Safety 5 1 1 Electric shock hazard 5 1 2 Installation and operation 5 1 3 Maintenance and repair 5 2 Short information 7 2 1 About this manual 7 2 2 Conventions in this manual 7 2 3 Intended use 7 2 4 EU Directives 7 2 5 Rating plate 7 3 System overview 8 3 1 Parts included 8 3 2 System requirements 8 3 3 Overview of functions 8 3 4 Connections controls and displays 11 3 4 1 Front view 11 3 4 2 Rear view 12 4 Installation 13 4 1 Preparations 13 4 2 Installing in a switch cabinet 13 5 Connection 15 5 1 Connecting cameras 15 5 2 Establishing the network connection 16 5 3 Connecting audio 16 5 4 Connecting alarm inputs and relay output 17 5 5 Creating a serial connection 18 5 6 Power on power off 19 6 Configuration 20 6 1 Setup 20 6 2 Setup using Bosch Video Client 20 7 Troubleshooting 22 TA Contact 22 7 2 General malfunctions 22 7 3 Malfunctions with iSCSI connections 23 7 4 LEDs 23 7 5 Processor load 24 7 6 Network connection 24 7 7 Terminal block 24 Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 4 en Table of Contents VIP X16 XF E 7 8 Copyrights 25 8 Maintenance 26 8 1 Updates 26 8 2 Factory reset 26 8 3 Repairs 26 9 Setting out of order 27 9 1 Transfer and disposal 27 10 Technical data 28 10 1 Electrical 28 10 2 M
13. a the Start button and the Programs menu path Start Programs Bosch Video Client Bosch Video Client 2 When the program is started for the first time a wizard opens to help you detect and configure devices on the network 3 Ifthe wizard does not start automatically click to open the Configuration Manager application Then click Configuration Wizard on the Tools menu 4 Follow the instructions given in the Configuration Wizard window F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E Configuration en 21 Configuration Wizard BOSCH Welcome refer anager Additional parameters You can check and set additional parameters with the assistance of the Configuration Manager application in Bosch Video Client You can find detailed information on this in the documentation for these applications Note that the audio function is not activated by default To use audio connections activate the corresponding setting when configuring the unit Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 22 en Troubleshooting VIP X16 XF E 7 7 1 7 2 Troubleshooting Contact If you are unable to resolve a malfunction please contact your supplier or systems integrator or go directly to Bosch Security Systems Customer Service The following tables are intended to help you identify the causes of malfunctions and correct them where
14. echanical 28 10 3 Environmental conditions 28 10 4 Certifications and approvals 28 10 5 Standards 29 F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E Safety en 5 1 Safety 1 1 Electric shock hazard Never attempt to connect the unit to any power network other than the type for which it is intended Connect the unit to an earthed mains socket outlet Never open the housing If a fault occurs disconnect the unit from the power supply and from all other units Install the unit only in a dry weather protected location When installing in a switch cabinet ensure that the unit has sufficient grounding If safe operation of the unit cannot be ensured remove it from service and secure it to prevent unauthorized operation In such cases have the unit checked by Bosch Security Systems Safe operation is no longer possible in the following cases if there is visible damage to the unit or power cables ifthe unit no longer operates correctly if the unit has been exposed to rain or moisture if foreign bodies have penetrated the unit after long storage under adverse conditions or after exposure to extreme stress in transit 1 2 Installation and operation The relevant electrical engineering regulations and guidelines must be complied with at all times during installation Relevant knowledge of network technology is required to ins
15. iding up to ten programmable recording profiles and allowing individually assigned camera profiles With these profiles you can accelerate the frame rate as well as increase the quality on alarm saving recording space during non alarm periods Multicast In suitably configured networks the multicast function enables simultaneous real time video transmission to multiple receivers The UDP and IGMP V2 protocols must be implemented on the network for this function Access security The VIP X16 XF E encoder offers various security levels for accessing the network the unit and the data channels As well as password protection with up to three levels they support 802 1x authentication using a RADIUS server for identification You can secure Web browser access by HTTPS using a SSL certificate that is stored in the unit For total data protection each communication channel video audio or serial O can be independently AES encrypted with 128 bit keys once the Encryption Site License has been applied Remote control For remote control of external units such as pan or tilt heads for cameras or motorized zoom lenses control data is transmitted via the encoder s bidirectional serial interface This interface can also be used to transmit transparent data Intelligence VIP X16 XF E comes with built in MOTION video motion detection This motion detection algorithm is based on pixel change and includes object size filtering capabilities On alar
16. m VIP X16 XF E can send an e mail with JPEG images attached ONVIF conformance Conformance to ONVIF 1 02 and ONVIF Profile S provides interoperability between network video products regardless of manufacturer In addition the firmware of the device supports all applicable features of the ONVIF 2 2 specification Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 10 en System overview VIP X16 XF E ONVIF conformant devices are able to exchange live video audio metadata and control information and ensure that they are automatically discovered and connected to network applications such as video management systems Summary The VIP X16 XF E encoder provides the following main functions Video audio and data transmission over IP data networks Dual Streaming function for the encoder for simultaneous encoding with two individually definable profiles Multicast function for simultaneous image transmission to multiple receivers 16 analog BNC composite video inputs PAL NTSC Video encoding to international standard H 264 Deinterlacing at video input and progressive encoding Integrated Ethernet port 10 100 1000 Base T Network attached iSCSI recording Transparent bidirectional data channel via RS 232 RS 422 RS 485 serial interface Configuration and remote control of all internal functions via TCP IP also secured via HTTPS Password protection to prevent unauthorized connection or configuration
17. nable cookies to be set from the IP address of the unit In Windows 7 deactivate protected mode on the Security tab under Internet Options You can find notes on using Microsoft Internet Explorer in the online Help in Internet Explorer Additional configuration and operational requirements You find the information on additional configuration and operational requirements in the Releaseletter document for the respective firmware For the latest version of the firmware required programs and controls and the current version of the Bosch Video Client BVC management software access your Bosch product catalog on the Internet 3 3 Overview of functions Network video server The VIP X16 XF E encoder is a compact network video server for 16 connected video sources It is primarily designed for encoding video audio and control data for transfer over an IP network With its encoding in the H 264 format the unit is ideally suited for making existing analog CCTV cameras IP compatible and for remote access to digital VCRs and multiplexers The use of existing networks means that integration with CCTV systems or local networks can be achieved quickly and easily Video images from a single sender can be received simultaneously on multiple receivers Audio signals can also be transmitted from and to compatible units Dual Streaming The VIP X16 XF E encoder uses the feature Dual Streaming to generate two independent IP video streams per channel both at full
18. ns are secure 2 Connect each alarm input to a ground contact GND Relay output The VIP X16 XF E encoder has one relay output for switching external units such as lamps or alarm sirens You can operate the relay output manually while there is an active connection to the encoder The output can also be configured to automatically activate sirens or other alarm units in response to an alarm signal The relay output is also located on the terminal block CAUTION Please observe the labeling on the unit A maximum load of 30 Vp p SELV and 200 mA may be applied to the relay contacts 5 5 1 Connect the lines to the appropriate terminals R on the terminal block and check that the connections are secure 2 Connect the terminal block to the socket on the unit observing the labeling Further topics Section 7 7 Terminal block page 24 Creating a serial connection The bidirectional data interface is used to control units connected to the VIP X16 XF E encoder such as a dome camera with a motorized lens The connection supports the RS 232 RS 422 and RS 485 transmission standards A video connection is necessary to transmit transparent data F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E Connection en 19 The encoder offers the serial interface via the terminal block The range of controllable equipme
19. nsors Other applications are not permitted In the event of questions concerning the use of the unit which are not answered in this manual please contact your sales partner or Bosch Sicherheitssysteme GmbH Robert Bosch Ring 5 85630 Grasbrunn Germany www boschsecurity com 2 4 EU Directives The VIP X16 XF E encoder complies with the requirements of EU Directives 89 336 Electromagnetic Compatibility and 73 23 amended by 93 68 Low Voltage Directive 2 5 Rating plate For exact identification the model name and serial number are inscribed on the bottom of the housing Please make a note of this information before installation if necessary so as to have it to hand in case of questions or when ordering spare parts Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 8 en System overview VIP X16 XF E 3 System overview 3 1 Parts included 1VIP X16 XF E video encoder 1 accessory bag 1 Installation Manual 2 power cords EU US one each NOTICE Check that the delivery is complete and in perfect condition Arrange for the unit to be checked by Bosch Security Systems if you find any damage 3 2 System requirements General requirements Computer with Windows XP or Windows 7 operating system Network access Intranet or Internet Screen resolution at least 1 024 x 768 pixels 16 or 32 bit color depth Installed Sun JVM NOTICE The Web browser must be configured to e
20. nt is expanding constantly The manufacturers of the relevant equipment provide specific information on installation and control Please take note of the appropriate documentation when installing and operating the unit to be controlled The documentation contains important safety instructions and information about permitted uses CAUTION Please observe the labeling on the unit 5 6 1 If you require a serial connection to the VIP X16 XF E encoder connect the relevant cables to the terminal block and check that the connections are secure 2 Connect the terminal block to the socket on the unit observing the labeling Further topics Section 7 7 Terminal block page 24 Power on power off The VIP X16 XF E is delivered together with two power cords one for EU one for US mains socket outlets CAUTION Use only the suitable power cord Where necessary use suitable facilities to ensure that the power supply is free of interference such as voltage surges spikes or brownouts Connect the unit to an earthed mains socket outlet Do not connect the unit to the power supply until all other connections have been made 1 Select the suitable power cord and connect it to the unit 2 Plug the power cord into the mains The unit is ready for use as soon as the CONNECT LED lights up Provided the network connection has been correctly made the LINK LED also lights up The flashing LED ACTIVITY signals traffic on the network
21. o 3 5 mm 1 8 in stereo socket line out for connecting one audio connection 6 Power supply input for connecting the power cable Further topics Section 7 4 LEDs page 23 Section 7 7 Terminal block page 24 F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E Installation en 13 4 Installation 4 1 Preparations The VIP X16 XF E encoder is designed for installation in a switch cabinet Mounting the unit in a 19 inch rack using the installation material supplied is a quick and easy operation CAUTION The unit is designed for indoor operation Select a suitable location for installation that guarantees to meet the environmental conditions The ambient temperature must be between 0 and 50 C 32 and 122 F The relative humidity must not exceed 95 non condensing The unit generates heat during operation During installation please note the maximum heat value of 55 BTU h Ensure that there is adequate ventilation and enough clearance between the unit and heat sensitive objects or equipment Please ensure the following installation conditions Do not install the unit close to heaters or other heat sources Avoid locations exposed to direct sunlight Allow sufficient space for running cables Ensure that the unit has adequate ventilation Bear the total heat output in mind particularly when installing multiple units in a switch cabinet When making connections
22. possible General malfunctions Malfunction Possible causes Recommended solution No image transmission to remote station Camera error Connect local monitor to the camera and check the camera function Faulty cable connections Check all cables plugs contacts and connections No connection established no image transmission The unit s configuration Check all configuration parameters Faulty installation Check all cables plugs contacts and connections Wrong IP address Check the IP addresses Faulty data transmission within the LAN Check the data transmission with e g ping The maximum number of connections has been reached Wait until there is a free connection and then call the unit again No audio transmission to remote station Hardware fault Check that all connected audio units are operating correctly Faulty cable connections Check all cables plugs contacts and connections Incorrect configuration Check audio parameters The audio connection is already in use by another receiver Wait until the connection is free and then call the unit again The unit does not report an alarm Alarm source is not selected Check alarm source settings No alarm response specified Specify the desired alarm response change the IP address if necessary Control of cameras or other units is not possible
23. rews are tight Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 14 en Installation VIP X16 XFE F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E Connection en 15 5 Connection 5 1 Connecting cameras You can connect a maximum of 16 video sources to the VIP X16 XF E encoder Any cameras and other video sources that produce a standard PAL or NTSC signal are suitable gt Connect each of the cameras or other video sources to BNC sockets Video In 1 to Video In 16 using a video cable 75 Ohm BNC plug Note that termination is always on Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 16 en Connection VIP X16 XF E 5 2 Establishing the network connection You can connect the VIP X16 XF E encoder to a 10 100 1000 Base T network using a standard UTP category 5 cable with RJ45 plugs gt Connect the unit to the network via the ETH socket 5 3 Connecting audio Line Out 1 GND N The VIP X16 XF E encoder has two audio ports for audio line signals F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E Connection en 17 The audio signals are transmitted two way and in sync with the video signals The following specifications should be complied with in all cases 2 x audio in Impedance 9 kohm typ
24. t RS 232 mode RS 422 mode RS 485 mode RXD RxD receive data RxD receive data plus _ GND GND ground _ _ Pin assignment I O Contact Function IN1 Input alarm 1 IN2 Input alarm 2 IN3 Input alarm 3 INA Input alarm 4 GND Ground R Relay output Connect each alarm input to a ground contact GND 7 8 Copyrights Fonts The firmware uses the fonts Adobe Helvetica Bold R Normal 24 240 75 75 P 138 15010646 1 and Adobe Helvetica Bold R Normal 12 120 75 75 P 70 ISO10646 1 under the following copyright Copyright 1984 1989 1994 Adobe Systems Incorporated Copyright 1988 1994 Digital Equipment Corporation Permission to use copy modify distribute and sell this software and its documentation for any purpose and without fee is hereby granted provided that the above copyright notices appear in all copies and that both those copyright notices and this permission notice appear in supporting documentation and that the names of Adobe Systems and Digital Equipment Corporation not be used in advertising or publicity pertaining to distribution of the software without specific written prior permission Software This software is based in part on the work of the Independent JPEG Group Audio AAC audio technology licensed by Fraunhofer IIS http www iis frauhofer de amm Z Fraunhofer Fraunhofer IIS AAC LC Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 26 en Maintenance VIP X16 XF E 8 8
25. tall the unit Before installing or operating the unit make sure you have read and understood the documentation for the other equipment connected to it such as cameras The documentation contains important safety instructions and information about permitted uses Perform only the installation and operation steps described in this manual Any other actions may lead to personal injury damage to property or damage to the equipment Please ensure the following installation conditions Do not install the unit close to heaters or other heat sources Avoid locations exposed to direct sunlight Allow sufficient space for running cables Ensure that the unit has adequate ventilation Bear the total heat output in mind particularly when installing multiple units in a switch cabinet When making connections use only the cables supplied or use appropriate cables immune to electromagnetic interference Position and run all cables so that they are protected from damage and provide adequate cable strain relief where needed When installing in a switch cabinet ensure that the screw joints are free of tension and subject to as little mechanical stress as possible Ensure that the unit has sufficient grounding 1 3 Maintenance and repair Never open the housing of the unit The unit does not contain any user serviceable parts Bosch Sicherheitssysteme GmbH Installation Manual F 01U 281 864 V2 2012 12 6 en Safet
26. use only the cables supplied or use appropriate cables immune to electromagnetic interference Position and run all cables so that they are protected from damage and provide adequate cable strain relief where needed Avoid impacts blows and severe vibrations as these can irreparably damage the unit 4 2 Installing in a switch cabinet CAUTION When installing in a switch cabinet ensure that there is sufficient ventilation for the unit There must be at least 5 cm 1 97 in of free space to the left and right of the unit and at least 10 cm 3 94 in at the rear The unit generates heat during operation During installation please note the maximum heat value of 55 BTU h When mounting additional units direct contact with the encoder is permitted provided that the surface temperature of the adjacent units does not exceed 50 C 122 F When installing in a switch cabinet ensure that the screw joints are free of tension and subject to as little mechanical stress as possible Ensure that the unit has sufficient grounding 1 Prepare the switch cabinet in such a manner that you are easily able to insert the unit directly at the installation point 2 Place the cage nuts in the corresponding drillings or spaces in the switch cabinet frame 3 Lift the unit into the switch cabinet frame and insert the fastening screws together with the washers 4 Tighten the screws one after the other and then check once more that all the sc
27. y VIP X16 XF E Ensure that all maintenance or repair work is carried out only by qualified personnel electrical engineers or network technology specialists In case of doubt contact your dealer s technical service center F 01U 281 864 V2 2012 12 Installation Manual Bosch Sicherheitssysteme GmbH VIP X16 XF E Short information en 7 2 Short information 2 1 About this manual This manual is intended for persons responsible for the installation and operation of the VIP X16 XF E encoder International national and any regional electrical engineering regulations must be followed at all times Relevant knowledge of network technology is required The manual describes the installation of the unit 2 2 Conventions in this manual In this manual the following symbols and notations are used to draw attention to special situations CAUTION This symbol indicates that failure to follow the safety instructions described may endanger persons and cause damage to the unit or other equipment It is associated with immediate direct hazards NOTICE This symbol refers to features and indicates tips and information for easier more convenient use of the unit 2 3 Intended use The VIP X16 XF E encoder transfers video audio and control signals over data networks Ethernet LAN Internet The unit is intended for use with CCTV systems Various functions can be triggered automatically by incorporating external alarm se
Download Pdf Manuals
Related Search