KIP 7170K User Manual
Contents
1. A NOTE 1 A paper mis feed tends to occur just before out of a roll paper 2 A tracing roll paper is recommended to be loaded to Roll Deck 1 front 1 Pull the blue lever 1 to unlock the Roll Deck Draw out the Roll Deck 2 5 Chapter 2 Basic Operation 3 Raise the green lever 4 on Flange 2 Remove both Flanges 4 from the roll core 3 4 Move a right Slide Guide 5 to match your roll media s width The right and left Side Guides will automatically move together vr dr V 2 6 Chapter 2 Basic Operation 5 Insert each Flange 2 into both ends of the roll media core to be installed A NOTE 1 Fully insert Flange into the roll media core so that the inside rim of Flange evenly touches the side face of the roll media Inside Rim Inside Rim Correct Fully inserted Wrong not touching roll side 2 Flange has Stoppers with sharp edge Be sure not to touch them 6 Push both the levers 4 down in either way Position them flat against Flange to secure the roll media 2 7 Chapter 2 Basic Operation 7 Lift the roll media by holding both Flanges Lower Flanges onto Slide Guides 5 in Roll Deck A NOTE 1 Be careful of the winding direction of the roll media Rear Deck back Rear Deck back Front to media path Correct Edge comes from bottom Wrong Edge comes from top 2 The outside rim 6 of Flange should meet the black triangle 7 marked on Slide2. 1 Be sure to close the Engine Unit firmly until it locks at the correct position 2 The mis feed cut sheet should be replaced with a new one if its leading edge has a torn or fold Or it should be used upside down to keep the damaged edge from been inserted An extremely creased cut sheet may cause mis feed again 5 Replace Print Trays in the original position 3 7 Chapter 3 Error Correction 3 1 3 Media Feed Section Jam Registration Mis feed Separation Mis feed Media Feed Section Media Feed Section Registration Mis feed Separation Mis feed ununi 1 Remove all Print Trays 1 3 8 Chapter 3 Error Correction 3 Remove the mis fed paper 4 Gently close the Engine Unit A NOTE Be sure to close the Engine Unit firmly until it locks at the correct position 5 Replace Print Trays in the original position 3 9 Chapter 3 Error Correction 3 1 4 Fuser Section Jam Exit Back Mis feed Fuser Section Exit Back Mis feed C o dp 1 Remove all Print Trays 1 3 10 Chapter 3 Error Correction 3 Remove the mis fed paper If the mis fed paper cannot be seen or removed leave the media and go to the next step If the paper including any torn part can be removed go to step 8 4 Hold the gray handles and open the Exit Cover 3 5 Pull and remove the jammed print to the rear If you remove the print at this time just close the Exit Cover I
3. Press down Scanner Unit on both side to close it Do not close it by pressing only one side down 4 6 Chapter 4 Maintenance 4 2 Touch Screen 1 Wipe the Touch Screen with a dry cloth Do not use water alcohol organic solvent and glass cleaner for the cleaning 4 7 Chapter 4 Maintenance Multi Function Printer KIP 7170 Hardware Operation Guide Version A 1 Issued on April 20 2015 Please note that some articles illustrations and photographs might be partially different from the actual machine because of the modification of machine and so on No part of this publication may be copied reproduced or distributed in any form without express written permission from KIP
4. The above specifications are subject to change without notice 1 7 Chapter 1 Before Use 1 4 3 Scanner part Subject Scanning method Contact Image Sensor CIS 5 pieces of A4 sized CIS Light source LED R G B Scanning speed Monochrome 65mm s 600 dpi normal quality Grayscale 65bmm s max Color 22mm s NOTE The actual speed may vary by the scan software Setting of original Starting point of scan Scan width Max 914 4mm 36 Min 210mm Scan length Max 6 000mm 19 7ft Including the margin area Min 210mm 8 5 Including the margin area NOTE If the print is longer than 6 000mm its image quality or the reliability of paper feeding is not guaranteed Optical resolution 600dpi Digital resolution 200 300 400 600 dpi Original transportation Sheet through type Transportable original Max 1 60mm thickness Min 0 05mm NOTE Suggest to change It does not guarantee both scan copy image quality and original feeding reliability in case the original is non standard size one of which thickness is 0 25mm or thicker A NOTE The above specifications are subject to change without notice 1 8 Chapter 1 Before Use 1 5 Appearance 1 5 1 Front view ame ain Switch You can turn on off the KIP 7170 riginal Guides Feed the original under the Scanner Unit along the Original Guides User Interface This is a Touch Screen and many kinds of user operation are available P
5. KIP KIP 7170K User Manual Version A 1 SYSTEM K SOFTWARE gt Thank you for purchasing the Multi Function Printer KIP 7170 This Hardware Operation Guide contains functional and operational explanations for the KIP 7170 Please read this Hardware Operation Guide carefully before using the printer Please keep this Hardware Operation Guide for future reference 1 When this product is installed in North America This product complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This product may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation FCC CAUTION Changes or modifications not expressly approved by the party responsible for compliance could void the user s authority to operate the product Note This product has been tested and found to comply with the limits for a Class A digital equipment pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the product is operated in a commercial environment This product generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this product in a residential area is likely to cause harmful interference in which case the user wi
6. Guide Otherwise the roll media may fall in Roll Deck or result in an incorrect media feeding Correct 2 8 Chapter 2 Basic Operation 8 Insert the leading edge of the roll media under Guide Plate 8 until it touches the feeding roller Rotate Feed Knob 9 clockwise so that the feeding rollers catch the leading edge A NOTE Use the rear Feed Knob 10 for Roll Deck 2 9 Hold the green grip 11 on the middle of Guide Plate and turn Guide Plate outside With holding rotate Feed Knob 9 again so that the leading edge comes out in 100mm Leading edge of 2 9 Chapter 2 Basic Operation 10 Slide the green Cutter Knob 12 fully from one side to the other to make a new straight edge Remove the cut portion A NOTE Completely slide Cutter Knob 12 until it stops at either end Not doing so may cause a paper jam Correct 11 Gently close Roll Deck A NOTE Be sure to close the Roll Deck fully until it locks at the correct position A paper jam may occur if it is not locked firmly 2 10 Chapter 2 Basic Operation 2 4 Replacing Toner Cartridge A WARNING There is combustible powder in the toner cartridge Do not burn up the used toner cartridge Reference When the toner is empty the Ul Screen will display Toner Empty sign Follow the later procedure or as noted in the Ul s User Guide to replace the Toner Cartridge with a new one genuine A NOTE 1 The KI
7. Service Call Errors If an error with significant effect on the printer occurs the printer stops the operation and indicates a related Customer Engineer Call Error Code or description and its equivalent internal code on the UI screen Call the service staff immediately as these problems can be fixed by a well trained technician only Before calling the service staff try to turn on off the Printer If Service Call Error is indicated again turn off the machine unplug it and call the service staff with reporting the error description in the Ul screen Service Call Error Fusing Temperature Error Motor Error Developer Error Counter Error Cutter Error Density Sensor Error High Voltage Power Supply Error A corresponding description will be displayed in the top column status region in the UI screen PE eer COPY SCAN PRINT COPY SCAN PRINT JOB INFO ACCOUNTING GUIDES a 9 MEDIA TONER Roll 1 Roll 2 DI HH 99 o ISO A1 ISO A2 eee Bond Bond e hd e hd 3 21 Chapter 3 Error Correction Chapter 4 Maintenance page 4 1 SSO Taille TG 4 2 4 1 1 Scan Glass Feed Roller Guide Plate s 4 2 4 1 2 Sensor 4 5 4 2 TOUCh SGre Sart eee E S E 4 7 4 1 Chapter 4 Maintenance 4 1 Scanner Unit 4 1 1 Scan Glass Feed Roller Guide Plate It is recommended to clean each Scan Glass Feeding Rollers and Guide Plates as the scan copy image may become defective
8. if these parts are dirty NOTE For ease of visual check this document shows the Upper Unit fully open not actual wide 1 Turn off KIP 7170 2 Lift up both sides 1 of the Scanner Unit 4 2 Chapter 4 Maintenance 3 Gently wipe the Scan Glass 2 and Feed Rollers white 3 with a soft cloth Equal mixture of water and neutral detergent can be used Do not use organic solvent glass cleaner and anti static spray for the cleaning 4 Wipe the Feed Rollers rubber 4 with a dry cloth 5 Wipe dry the Feeding Rollers 4 3 Chapter 4 Maintenance 6 Wipe the Upper Guide Plate 5 and the Lower Guide Plate 6 with a dry cloth 7 Gently press Scanner Unit down and firmly close it NOTE Press down Scanner Unit on both side to close it Do not close it by pressing only one side down 4 4 Chapter 4 Maintenance 4 1 2 Sensor If Sensors are dirty the original may be detected incorrectly Perform cleaning or as needed NOTE For ease of visual check this document shows the Upper Unit fully open not actual wide 1 Turn off KIP 7170 2 Lift up both sides 1 of the Scanner Unit 4 5 Chapter 4 Maintenance 3 Gently wipe Sensors 2 with a dry cotton bud Do not use water organic solvent glass cleaner or antistatic spray for cleaning 4 Gently press Scanner Unit down and firmly close it NOTE
9. 1 Pull the blue lever 1 to unlock the Roll Deck Draw out the Roll Deck 2 Rewind the roll media 3 3 Chapter 3 Error Correction 3 Insert the leading edge of the roll media under Guide Plate 2 until it touches the feeding roller Rotate Feed Knob 3 clockwise so that the feeding rollers catch the leading edge A NOTE 1 The leading edge should be trimmed with a cutter in case of an extreme crease 2 Use the rear Feed Knob 4 for Roll Deck 2 4 Hold the green grip 5 on the middle of Guide Plate and turn Guide Plate outside With holding rotate Feed Knob 3 again so that the leading edge comes out in 100mm Leading edge of roll media COE 3 4 Chapter 3 Error Correction 5 Slide the green Cutter Knob 6 fully from one side to the other to make a new straight edge Remove the cut portion A NOTE Completely slide Cutter Knob 6 until it stops at either end Not doing so may cause a paper jam 6 Gently close Roll Deck A NOTE Be sure to close the Roll Deck fully until it locks at the correct position A paper jam may occur if it is not locked firmly 3 5 Chapter 3 Error Correction 3 1 2 Manual Feeder Section Jam Registration Mis feed Manual Feeder Section Registration Mis feed O 1 Remove all Print Trays 1 3 6 Chapter 3 Error Correction 3 Remove the mis fed paper pulling frontward 4 Gently close the Engine Unit A NOTE
10. 2 Basic Operation 4 The KIP 7170 will start the copy process x B amp W COPY G AUTO START INTERRUPT TEMPLATES SAVE TEMPLATE LOG OUT Reference Pressing START button may be required to start the scan according to the scanner s controller software O Start Button For further details of Auto Start see the software s n document A NOTE The scanner unit does not accept originals automatically during Sleep Mode Tap on the UI screen and then insert an original 2 18 Chapter 2 Basic Operation The KIP 7170 has 2 print delivery system the print tray front standard rear stacking equipment back option NOTE For the front stacking gently lift up the prints on the print tray to the arrow direction to avoid rubbing the print surface A large number of prints should be removed in several sheets Correct Gently lift up and remove Wrong Do not pull downward For the front stacking the printer will inform you of Upper Bin Full on exceeding capacity of stacking If the Ul screen shows Upper Bin Full remove all the prints on the print tray For further information of switching front back delivery see KIP IPS Touch screen Operator s Guide 2 19 Chapter 2 Basic Operation 2 7 Stop of Scan or Copy 1 If necessary press the Scan Abort Button on the Scanner Unit to immediately stop the original Scan Abort Button while making a copy or scan The LED Indicator flashes red
11. In case that Front Cover Open is still displayed even when each door is closed securely either interlock switch may be opened For this case open the Engine Unit once and then close it securely 3 18 Chapter 3 Error Correction 3 2 3 Paper Exit Door Paper Exit Door Open Close the Paper Exit Door securely to clear Paper Exit Door Open 3 2 4 Scanner Unit Scanner feeder open The Ul screen shows Scanner feeder open if the Scanner Unit is open not closed properly For closing the Scanner Unit see 3 1 6 Original Jam 3 19 Chapter 3 Error Correction 3 3 Other Operator Call Error 3 3 1 Roll Replacement When the printer is running out of an loaded roll media the UI Screen will display Out of Paper sign If there is no suitable roll media required for the current print job the Ul Screen will display Out of Paper sign as well Please load the required roll media to any Roll Deck For the roll replacement procedure see 2 3 Replacing Roll Media 3 3 2 Toner Empty When the printer is running out of toner the Ul Screen will display Toner Empty sign For the toner supply procedure see 2 4 Replacing Toner Cartridge 3 3 3 Accessory Error If your finishing device Auto Stacker Folder has an error the UI screen of the printer would also show an error message For clearing errors on such devices see the concerning device s User s Manual 3 20 Chapter 3 Error Correction 3 4
12. LEASE DO NOT push the LCD area too strong can Abort Button While scanning emergency stop At Standby position eject O CD OD tart Button Starts scanning if the controlling software requires user intervention canner Unit oner Hatch Open the Toner Hatch when you replace the Toner Cartridge Original Table Also put the original here and then feed it into the Scanner Unit when you make scan or copy ngine Unit Open Lever ypass Feeder oll Deck rint Tray ED Indicator Indicates the status of Scanner Unit green Ready red Error green to and fro Scanning red flashing Scanner Unit Open Jam Your USB flash memory storage can be installed here SVDC max Paper Tray OPTION Multiple cut sheets can be stored inside up to 50 1 9 Chapter 1 Before Use Mmmm KS N C LO UJ U O m Lx a I c NO 1 5 2 Rear view ie e ll Open the Paper Exit Door when you remove the paper misfed inside the Fuser Unit For an optional device D Sub Connector 9 pins 12VDC max Service Use 5VDC max Connect the LAN Cable to connect the KIP 7170 to the network Do not connect a telephone line It is possible to shut off supplying the AC power 7 Inlet Socket 5 Dehumidify Heater Switch Turn on the Dehumidify Heater with this switch when you DEHUMIDIFY KIT is an would like to dry the paper in the humid season optional part 6 Nd Connect the Power Cord here Chapte
13. P 7170 will indicate Toner Empty sign if an incorrect toner cartridge or no toner cartridge is installed to the printer 2 At the machine s installation some amount of initial toner powders will be supplied to the machine Thus Toner Empty sign might appear slightly earlier for the first installed toner cartridge than usual 1 Open the Toner Hatch 1 2 11 Chapter 2 Basic Operation Slide the green Lever 2 to the right to unlock the Toner Cartridge Lever 2 is held automatically B J l i WP 2 Ml H f I f J II 3 RE mi Correct disengaged Wrong not disengaged The green Lever 2 is shifted to the right 2 12 Chapter 2 Basic Operation 3 Pressing down the Cartridge Lock Lever 3 turn the body 4 of cartridge to the arrow direction until it stops You can close the toner supply hole of the cartridge firmly by this AAA 1 II ah VE A AN H A NOTE The toner may drop from the toner supply hole and it may scattered into the machine or on the floor if you remove the Toner Cartridge without closing the toner supply hole 5 4 Pressing down the Cartridge Lock Lever 3 bring up the left side of the Toner Cartridge first and then remove the whole cartridge from the machine AUDIO J L LNW ia T i i 15 f 1 A 2 13 Chapter 2 Basic Operation 5 Shake the new Toner Cartridge left and right 5 times or more to make the toner smooth After shaking t
14. Pressing the button stops the current reading a document immediately The current printing is stopped as well and is ejected NOTE Do not pull back or hold down the original on Original Table as an attempt to stop feeding it through Scanner Unit 2 20 Chapter 2 Basic Operation 2 8 Canceling Sleep Mode The KIP 7170 has two Sleep Modes to reduce the power consumption The KIP 7170 will enter Sleep Mode after a certain period of inactivity In the default setting e Warm Sleep Mode will start after a 15 minute of inactivity in order to reduce the power supply for Fuser Unit e Cold Sleep Mode will start after a 60 minute of inactivity to stop the power supply for Fuser Unit and some other components Sleep Mode is canceled and the machine gets ready when e the machine receives a print job through the network e you tap on the UI screen then an original is inserted the scanner unit NOTE 1 It may take time for the machine to get ready 2 Tapping on the UI screen can cancel the screensaver but the KIP 7170 needs to recover temperature on Fuser Unit It may need another waiting time to start warming up for printing 3 Recommended Default Delay Times 60min 2 21 Chapter 2 Basic Operation 2 9 Dehumidifying Roll Media For avoiding dehumidifying of roll media in the Roll Deck KIP7170 has an optional part DEHUMIDIFY KIT When creasing of media or void of image is seen caused by the humidifying of ro
15. and tracing paper 2 Remove the paper from the machine right after the completion of print and keep it in a polyethylene bag Void of image occurs when you print If you will not make print soon remove with tracing paper the tracing paper from the machine and keep it in a polyethylene bag Remove the paper from the machine after everyday use and keep it ina polyethylene bag Void of image occurs when you print If you will not make print soon remove with plain paper and tracing paper the tracing paper from the machine and keep it in a polyethylene bag Void of image crease of paper and 1 Turn on the Dehumidify Heater other problems occurs when you print if installed with plain paper and tracing paper 2 Remove the paper from the machine right after the completion of print and keep it in a polyethylene bag Dehumidify Heater DEHUMIDIFY KIT is optional parts A NOTE 1 KIP7170 has an optional part DEHUMIDIFY KIT Using it in high humidity environment 75 or higher is recommended Refer to 2 9 Dehumidifying Roll Paper 2 Void of image and crease of paper will occur in case of extremely high or low humidity Normal Print Crease of paper If the media is humidified If the media is humidified l 1 17 Chapter 1 Before Use Chapter 2 Basic Operation page Turning on KP 7170 NEE 2 2 Turning Off KIP 7170 encore cee et
16. aper 1 11 Chapter 1 Before Use 1 6 3 Do Not Scan Originals It is impossible to use the following types of originals because they are likely to damage the scanner Do not scan the following kinds of original because you may damage the original or scanner itself Sticked with paste Torn Folded Leading edge So much curled Diameter is smaller than 80mm 1 12 Chapter 1 Before Use Not square Wet image T Wet Made of metal or fabric Metal Fabric Rough surface Carbon paper for example Rough surface Clipped or stapled Clipped Stapled U 7 1 13 Chapter 1 Before Use The following kinds of originals can be read with using a carrier sheet However the image quality and feed reliability are not guaranteed Patched Punched 1 14 Chapter 1 Before Use 1 7 Specifications for the Printing Media 1 7 1 Papers not available to use Do not use the following kinds of printing paper Doing so may damage the print engine Excessively curled a diameter of 50 mm or less Folded 1 15 Chapter 1 Before Use 7 NN M e A CAUTION Do not use the paper with staple or do not use such conductive paper as aluminium foil and carbon paper The above may result in a danger of fire A NOTE 1 Print image may become light if printed on a rough surface of the paper 2 Print image may become defective if
17. be avoided Curl up sheets tend to result in a mis feed Correct curl down Incorrect curl up 2 Setting a cut sheet to the Bypass Feeder while the printer is processing a print job cause a paper jam 2 16 Chapter 2 Basic Operation 2 6 Copyin Please refer to the detailed procedure for making a copy which is included in GUIDES in UI Home screen as well 1 Press COPY in UI Home screen x 7170K Ready Pons B amp W COPY Ready KIP KIP copy SCAN PRINT i COPY COUNT L on START SS lil e COLLATE MEDIA CUT MODE COPY SCAN PRINT AUTO START ma a amp LJ gy T Sei ti m geg ZOOM FINISHING FORMAT VIEWER JOB INFO ACCOUNTING GUIDES E C gt x D ag 100 00 Auto BOA TEMPLATES SS SN Roll 1 Roll 2 gt N d Je Ee HH Hi P FE ie SS 1 0 A2 TO A3 cooo 6 Bond Bond Une Photo 2 here are several size markings on Original Table which indicate possible feed positions Line up Original Guides with the proper markings according to the original width Original Guide 3 Place the original on the Original Table with face up Then insert it under the Scanner Unit along with Original Guides When the leading edge touches the original feeding roller the machine automatically carries and sets the original at the proper position When the original is at wait position the LED Indicator will turn off Original Guide Sep X 7 Original Guide 2 17 Chapter
18. cate stamps which are prescribed by Liquor Tax Act or the Commodity Tax Act Special items to be cared 1 It is warned by the government to copy private issued securities stock certificate draft check goods ticket etc commutation ticket or book of tickets excluding that some specific company copies such originals as many as it requires for its own business 2 We recommend you not to copy freely such originals as government issued passport public or private issued licenses automobile inspection certification IDs and tickets like pass or meal Prohibited items to copy Regulations to control fake currency and Currency Bill Money Bank Note etc Bond Government issued Negotiable Instruments National Bonds Security Local Debt Bonds etc Control Law against Forged amp faked Foreign Currency or Foreign Negotiable Foreign Currency Bill Bank Note and Bond Instruments Forged postal stamps control law Unused postal stamps or government postcards Forged revenue stamps control law Government issued revenue stamps and certificate stamps prescribed by Liquor Tax Act or Commodity Tax Act Currency similarity securities Control Law Private issued securities stock draft check goods ticket etc commutation or book tickets Originals protected by the copyright It is prohibited to copy such originals as book music paintings printed copy maps drawings movie and pictures which are protected by the copyrig
19. d equipment such as noise or flickering may occur Use a separate power line and install the PRINTER as far as possible from said equipment 1 KIP 7170 is an ENERGY STAR qualified multifunction equipment ENERGY STAR The International ENERGY STAR Office Equipment Program is an international program that promotes energy saving through the penetration of energy efficient computers and other office equipment The program backs the development and dissemination of equipment with functions that effectively reduce energy consumption It is an open system in which business proprietors can participate voluntarily The targeted products are office equipment such as computers monitors printers facsimiles copiers scanners and multifunction devices Their standards and logos are uniform among participating nations The symbol shown indicates that this product conforms to Directive 2012 19 EU of the European Parliament and the council of 4 Juiy 2012 on waste electrical and electronic equipment WEEE and does not apply to countries outside of EU emm Only For EU Member States The symbol shown indicates that this product conforms to SJ T11364 2006 of People s Republic of China Electronic eS Gn Industry Standard and does not apply to countries outside of A AL y People s Republic of China The symbol shown indicates that this product conforms to GB 18455 2001 11364 2006 of National Standard of the People s Republic of Ch
20. e eee 2 4 Replacing Roll Media eee ee 2 P Replacing Toner Cartridge M n 2 11 Cut Sheet Media ossis hori eee lees bidet eles 2 16 Copying E 2 17 Stop ol Scan Of Copy 44 ee E 2 20 Canceling Sleep Mod 45 eee eee 2 24 Dehumidifying Roll Media M MM Md 2 22 2 1 Chapter 2 Basic Operation 2 1 Turning on KIP 7170 1 Plug the power cord for KIP 7170 into a dedicated wall outlet A WARNING 1 Do not handle the Power Plug with wet hands or you may receive an electrical shock 2 Make sure to earth the machine for safety 3 Do not plug the printer into a multi wiring connector in which other devices are plugged It may overheat the outlet and may result in a fire 4 The OUTLET must satisfy the following conditions In the U S A 120V plus minus 10 50 60Hz and 15A In Europe 220 240V plus 6 or minus 10 50 60Hz and 10A 2 Press side the Power Switch on the right side of the printer to turn on the KIP 7170 Power Switch Press side 2 2 Chapter 2 Basic Operation 3 The User Interface UI starts operating and displays the following Copy Mode Screen in one minute Warming Up is displayed in the status indication while warming up P 7170K Warming Up COPY SCAN PRINT COPY SCAN PRINT JOB INFO ACCOUNTING GUIDES Roll 1 Roll 2 ISO A1 ISO A2 Bond Bond The UI screen may vary depe
21. eececooososoccoooooooocoocosoococssocosoccoosocosococososocosocosococosooosocoocoososoooooosooocossosoooocoosocososososococosososoosoosooosocooooooocococosooocoosooocococosocososososoocoosocosocoococoocoosooooooeo 1 4 2 Printer part et0sososesosesoscososssosesosesss 0c000000000000000000000000000009000090000900009000090900000000900009000090000000000000000009000009000090000900000000090000900009000090000900000000009000090000900009000009000090900090900090900009909099909 1 4 3 Scanner part eesecsososocoocosocosocsocooooocoosocsoocooosocsososososocooosososococosososococooooosoosoosooocossoesoosososococosososococosooococsososooococooosoooooosoocoosocosococoosososococosooosococosocosocososooooooo 1 5 Appearance Sella aah Satie te ele ahaa an thas AO aes Nh P EP 1 5 1 Front view T P PPPPPPPPPPPPPPPo PPPPPPP P POwww0PPPOPOPOPOP POPPww 0 0w 0n0 eeeeeeeeeee eieeeeeePepePerr 1 5 2 Rear view etosososesosesssesosososesostos0000000000000900000000000000000000000000090000900090900900000090000900009000090000000000000000009090000900009000090000000000900009000090000900000000000000900009000090000900009000090900090900009000990909996 1 6 Specifications for Scan Original xut ep ac EU E ME Em ME DU d 1 6 1 Original E Standard EE 1 6 2 Special Dy VII IIR S LS et 1 6 3 Do Not Scan Originals FS CE AEA SRE EE d e 1 7 Specifications for the Printing WIG ace titre eden
22. f the print cannot be removed go to the next step If the print including any torn part can be removed go to step 8 jammed print 4 A NOTE If removed a mis fed paper inside the Exit Cover scattered toner can be adhered to the next print 3 11 Chapter 3 Error Correction Hold the gray areas 4 and release the Fuser Door 5 Pull and remove the jammed print to the rear A jammed print A WARNING There are extremely hot parts inside the Fuser Door Do not touch any parts in the Heater Unit or you will be burnt Also be careful not to get burnt when you touch the printing paper as it may be very hot A NOTE If removed a mis fed paper inside the Fuser Door scattered toner can be adhered to the next print Close Fuser Door 5 and Exit Cover 3 3 12 Chapter 3 Error Correction 8 Gently close the Engine Unit NOTE Be sure to close the Engine Unit firmly until it locks at the correct position 9 Replace Print Trays in the original position 3 13 Chapter 3 Error Correction 3 1 5 Stack Jam 1 Remowve print s on Print Trays 2 Remove all Print Trays 1 4 Pull and remove the jammed print to the top If the print cannot be removed see 3 1 4 Fuser Jam for the later procedure of clearing the jammed print 1 E y yi l lt y i f ti U jammed print 3 14 Chapter 3 Error Cor
23. hock due to a hot item or electrically charged part inside of the printer Do not disassemble or tamper with the printer It may result in a fire or an electrical shock Do not plug in the printer into a multi wire connector in which some other equipment is plugged into It may cause a fire due to outlet overheating Do not damage the Power Cord by stepping on or placing heavy items on it If the Power Cord is damaged it may cause a fire or you may receive an electric shock REPLACE THE CORD IF DAMAGED Do not put a flower vase a flowerpot or any water filled item on the product Spilt water could cause a fire or an electric shock If the product generates an abnormal smell or noise turn it off and unplug it from the wall electrical outlet immediately Do not throw the toner into a fire or other sources of heat as it can explode 4 CAUTION Do not install the printer in a humidified room or a dusty room Also do not install the printer on an unstable floor as injuries may occur 1 Unplug the printer before you move it The power cord may be damaged and it may result in a fire or electric shock If you do not use the printer for a long duration holidays company shutdown turn off and unplug the printer from the outlet for safety Do not pull the cord when you unplug the printer as you may damage the Power Cord There are hot items inside of the printer Take great care not to touch these items when y
24. ht except for personnel or family use or similar purpose 1 3 Chapter 1 Before Use 1 3 Features 1 KIP 7170 is a single footprint Multi Function Printer which can copy scan and print Advanced drivers and comprehensive print utilities make the KIP 7170 an advanced easy to use system some functions may be optional 2 KIP HDP technology generates no waste toner 3 The KIP HDP Plus imaging system produces high definition lines distinctive greyscale and consistent blacks 4 The maximum paper width is 36 914mm wide and the minimum is 11 279mm The maximum paper length is 6m with 36 paper or and the minimum is 8 5 210mm 5 Up to 600dpi print resolutions with an enhanced scanning system produces the highest quality images controlled by an advanced KIP Image Process System 6 Easy access to USB port allows users to provide efficient productivity by using File to Print Scan to USB option 7 2 way print delivery front up to 50 sheets of plain paper rear suits the preference of the user s print handling rear stacking requires a stacking device option 8 Various media source roll media feeding 2 rolls cut sheet manual feeding Paper Tray multiple cut sheet feeder option 9 Contactless IC card reader for more efficient accounting management option 10 KIP 7170 adopts 12 1 inch screen for the Ul wider than 8 5 for our old products The capacitive multi touch screen offers smooth var
25. ilt the Toner Cartridge to the cap side 6 Keep pressing down the Cartridge Lock Lever 3 Direct the toner supply hole to the floor fit the pin 6 on the left side of the cartridge to the groove 7 on the machine side A NOTE Please confirm that the Cartridge Lock Lever 3 firmly locks the Toner Cartridge at the correct position It must be at a level position 2 14 Chapter 2 Basic Operation 7 Turn the body 4 of the cartridge in two or more revolution to the arrow direction to open the toner supply hole Confirm that the projection 8 if fitted into the notch 9 It is not necessary to lock the cartridge with the Lever 2 Lever 2 will engage on its own after MA u UN MI II I closing the Toner Hatch A VW WI E HUE 8 Close the Toner Hatch 1 2 15 Chapter 2 Basic Operation 2 5 Cut Sheet Media 1 Open the Bypass Feeder 1 Bypass Feeder 2 here are several size markings on the table of Bypass Feeder which indicate possible feed positions Place the cut sheet paper on the table between its concerning size markings then insert it into the Bypass Feeder When the leading edge touches the feeding roller the machine automatically carries and sets the paper at the proper position size markings A NOTE 1 As a curly cut sheet will cause a mis feed straighten the sheet as far as possible before printing And set the sheet in curl down direction as a mis feed can
26. ina and does not apply to countries outside of People s Republic of China The product shown with available options May vary from the actual product 2 Safety Warnings The following warnings are very important in order to safely use this product These notes are important in preventing danger to the operator or operation of the printer The following symbols are found throughout the USER S Manual and have the following meaning WARNING This WARNING mark means that there is a possibility of death or serious injury if you ignore or do not follow the said instruction CAUTION This CAUTION mark means that there is a possibility of injury or physical damage if you ignore or do not follow the said instruction When marked with this symbol DO NOT ATTEMPT When marked with this symbol pay close attention to 3 WARNING Ground the product with a correct ground source or you may be electrically shocked The Power source should be as follows In USA 120V plus minus10 50 60Hz 15A or higher In Europe 220 240V plus6 or minus10 50 60Hz 10A or higher Use a circuit with a dedicated breaker Install the product as close to the wall outlet as possible If you wish to move the printer please contact your service personnel Do not remove the screw and do not open the cover if not instructed to do so in this User s Manual If you ignore this warning you may be burnt or receive an electric s
27. ious and intuitive user operation that a pressure sensing device lacks 1 4 Chapter 1 Before Use 1 4 Specifications 1 4 1 General Subject Specification KIP 7170 Configuration Power consumption 1 440W US model 1 680W or less EU Asia model scanner controller included Low power mode Acoustic noise Idling puce cL IE EE Aaah Max 50db Printing Ee Max 57db impulse sound excluded EN ISO 7779 Max 0 05ppm Measurement method under UL Standard Dimensions In case of attaching UI Tray 1587mm Width x 704mm Depth x 1510mm Height In case of excluding UI Tray 1346mm Width x 704mm Depth x 1105mm Height Environmental condition Temperature for usage 10 to 32 degrees Centigrade 50 to 89 6 F Humidity 15 to 85 RH Network Interface 10 BASE T 100 BASE TX 1000 BASE T USB2 0 5VDC max Inthe US 120V plus minus 1096 50 60Hz 12A In Europe 220 240V plus 6 or minus 1096 50 60Hz 7A A NOTE The above specifications are subject to change without notice 1 5 Chapter 1 Before Use 1 4 2 Printer part Subject Specification Printing method LED Array Electro photography Photoreceptor Organic Photoconductive Drum Print speed 80mm per second 3 4ppm E 5 8ppm D Landscape i 3 3ppm AO0 5 6ppm A1 Landscape Print head LED Array Resolution of print head 600dpi x 2400dpi Print width Maximum 914mm 36 Minimum or 297mm 11 roll media or 210mm 8 5 cut sheet Print leng
28. light as this will damage the Drum Ozone will be generated while this equipment is use although the quantity generated is within safe levels see certifications Ventilate the room if required Keep ample room around the equipment to ensure comfortable operation Refer to the following figure The equipment must be leveled and the floor strength must be ample to sustain the weight of the equipment 30cm 12 or larger Rear w o option KIP 7170 lt P lt _______ L R L R 35cm 14 or larger R must be larger than L L 5cm 2 or larger Front 80cm 32 or larger recommended 90cm 35 4 or larger for Paper Tray option 1 2 Chapter 1 Before Use 1 2 Originals Prohibited from Duplication It is not necessarily allowed to copy every kind of original You may be punished by the law if only you possess the copy of some kind of original We recommend you to consider enough before you copy such original Originals prohibited from copying by the law 1 It is not allowed to copy Currency Bill Money Bank Note etc Government issued Negotiable Instruments National Bonds Security Local Debt Bonds etc 2 It is not allowed to copy Foreign Currency or Foreign Negotiable Instruments 3 It is not allowed to copy unused postal stamps or government postcards without permission to make replica from Government 4 It is not allowed to copy Government issued revenue stamps certifi
29. ll Deck Deck 1 Open tela 3 18 3 2 2 Engine Unit Front Cover Open Eege 3 18 3 2 3 Paper Exit Door Paper Exit Door Open M 3 19 3 2 4 Scanner Unit Scanner feeder open satel a e Md cU ae ie cea cat eect ES 3 19 8 Other Operator Call e M M 3 20 3 93 4 ER EE E 3 20 3 9 2 Toner Emply ete et eect 3 20 3 3 3 Accessory Error D 1 m 3 20 4 Service Call Error i e a A a ea i E 3 21 3 1 Chapter 3 Error Correction 3 1 Paper Jam xxxx Mis feed is displayed in the Ul screen when the media is jammed The jammed location when displaying xxxx Mis feed is shown below Media Feed Section Manual Feeder Section Fuser Section Zu Ia O l D 9 E uu Roll Deck Section Roll Deck Section U NOTE 1 Be careful not to get paper cuts on your hand 2 Gently remove a jammed paper When it does not reach Fuser Unit toner on it may spill off If toner gets into eyes or your mouth immediately rinse them with water and contact a doctor 3 Gently remove a jammed paper When it does not reach Fuser Unit toner on it may spill off on your cloth Dust off your cloth Use cold water to wash in out Using hot water may leave a stain 3 2 Chapter 3 Error Correction 3 1 1 Roll Deck Section Jam Deck 1 2 Mis feed pU CT O O Roll Deck Section Deck 1 Mis feed Roll Deck Section Deck 2 Mis feed NS
30. ll be required to correct the interference at his own expense This product complies with Part 15 of FCC Rules and Industry Canada licence exempt RSS standard s Operation is subject to the following two conditions 1 this product may not cause interference and 2 this product must accept any interference including interference that may cause undesired operation of this product Le pr sent appareil est conforme aux la partie 15 des r gles de la FCC et CNR d Industrie Canada applicables aux appareils radio exempts de licence L exploitation est autoris e aux deux conditions suivantes 1 l appareil ne doit pas produire de brouillage et 2 l utilisateur de l appareil doit accepter tout brouillage radio lectrique subi m me si le brouillage est susceptible d en comprometter le fonctionnement Contains FCC ID VP8 13551 Contains IC 7391A 13551 2 When this product is installed in Europe This product complies with the requirements in CISPR 22 for a Class A computing equipment Operation of this product in a residential area may cause unacceptable interference to radio and TV reception requiring the operator to take whatever steps are necessary to correct the interference Do not install product around other electronic equipment or other precision instruments Other equipment may be effected by electrical noise during operation If the product is installed near other electronic equipment such as a TV or a radio interference to sai
31. ll media it is recommended to use this kit Ask your service personnel for DEHUMIDIFY KIT If the roll paper is extremely humidified it may cause several kinds of defective print Defective prints you will experience most will be crease of paper and loss of image Normal Print Crease of paper If the media is humidified If the media is humidified SS If the KIP 7170 is installed in such a condition it is recommended to use the optional embedded Dehumidify Heater Turn on the Dehumidify Heater if the room air has too much humidity 75 or higher to prevent the above kinds of print defect Such problems above may be resolved To turn on the Dehumidify Heater press the H side of the Dehumidify Heater Switch on the rear Press its L side to turn off 2 22 Chapter 2 Basic Operation Chapter 3 Error Correction page 4 Paper Jam nnns a9 3 1 1 Roll Deck Section Jam Deck 1 2 Mis feed e e aren M 3 3 3 1 2 Manual Feeder Section Jam Registration Mis feed 3 6 3 1 3 Media Feed Section Jam Registration Mis feed Separation Mis feed 3 8 3 1 4 Fuser Section Jam Exit Back Mis feed le 3 10 3 1 5 STAC ca Sai kites teers A ect teeta tt 3 14 3 1 6 Original JAT e 3 16 3 1 7 Accessory JAY ege 3 17 2 Door Open M de 3 1 8 3 2 1 Ro
32. nding on your system configuration Shown with available options A NOTE It is not possible to print while displaying Warming Up in the status indication 4 Ready is displayed in the status indication when KIP 7170 is available to print Peng COPY SCAN PRINT COPY SCAN PRINT JOB INFO ACCOUNTING GUIDES e 29 MEDIA TONER Roll 1 Roll 2 HH ui e o ISO A1 ISO A2 Bond Bond eeee 2 3 Chapter 2 Basic Operation 2 2 Turning off KIP 7170 1 There is a Power Switch on the right side of KIP 7170 Press its CY side to turn off the KIP 7170 Power Switch Press Cy side A CAUTION The KIP 7170 print engine and UI appear to be shut down when you turn off KIP 7170 However the controller PC embedded inside the KIP 7170 is still operating and will shutdown in approximately two minutes after Power Switch operation Do not unplug the KIP 7170 before the controller PC completes its shutdown Doing so may damage data or the device 2 4 Chapter 2 Basic Operation 2 3 Replacing Roll Media 1 When the printer is running out of a roll media the UI Screen will display Out of Paper sign Follow the later procedure or as noted in the Ul s User Guide to load a roll media Please refer to your KIP IPS Touch Screen Operator s Guide for the Ul screen 2 This section describes how to install a roll media to Roll Deck 1 The same procedure is applied to Roll Deck 2 unless otherwise noted
33. ou remove mis fed media Ventilate the room well if you print in a small area 5 POWER CORD INSTRUCTION The installation of or exchange to a power plug which fits in the wall outlet of the installation location shall be conducted in accordance with the following N WARNING Select a power plug which meets the following criteria The plug has a voltage and current rating appropriate for the product s rating marked on its name plate The plug meets regulatory requirements for the area he plug is provided with a grounding pin or terminal If the appropriate plug does not fit the wall outlet in the installation the customer shall install an appropriate outlet Connector Type Configuration Standard Usually found in IEC60320 C13 10A 250V IEC 15A 125V UL Usuallyfound in Plug Type Model Rating 220 240V Configuration Standard Usually found in 9 o ASINZS 3112 10A 250V Australia New Zealand GB1002 10A 250V China GB2099 1 IRAM 2073 10A 250V BS 1363 10A 250V United Kingdom SASO 2203 10A 250V Saudi Arabia BS 546A 15A 250V United Kingdom IS 1293 India SABS 1293 south Africa SEV 1011 10A 250V Switzerland Chapter 1 Before Use page 1 1 Installation Requirements EE 1 2 Originals Prohibited from Duplication T tats 1 3 Features a E ptam n OIL IE ad SOF OIC A e id OU at RUE I UM a LE an arte TE 1 4 Specifications XII T DET 1 4 1 General
34. r 1 Before Use 1 6 Specifications for Scan Original A scan original must satisfy the following specifications 0 05mm to 1 60mm Width 210mm to 914 4mm Length 210mm to 6 000mm NOTE 1 Suggest to change It does not guarantee both scan copy image quality and original feeding reliability in case the original is non standard size one of which thickness is 0 25mm or thicker 2 Image quality for an original over 6 000mm in length is not guaranteed 1 6 1 Original Standards 1 The width of original must range from 8 5 to 36 210mm to 914 4mm 2 The length of original must range 8 5 210mm to 6 000mm 3 The thickness of original must range from 0 05mm to 0 25mm 4 The shape of original must be square and it must be standard sized 5 The type of original must belong to any of the followings Plain paper Coated paper High or middle class plain paper is coated with the paint Tracing paper Pansy Trace Paper Both sides of the film is sandwiched between Tracing paper Film Newspaper Cardboard paper 1 6 2 Special Documents The following kinds of originals are special It is possible to scan them Angur R D ESTA and feed relabltv are not gouaranteed 1 The type of original is acceptable but the thickness and type may not be Booklets Original with a Hanger Cut and Pasted originals 2 These original may not damage the scanner but these types are NOT recommended following ones Cloth Aluminium Kent P
35. rection 5 Gently close the Engine Unit A NOTE Be sure to close the Engine Unit firmly until it locks at the correct position 6 Replace Print Trays in the original position 3 15 Chapter 3 Error Correction 3 1 6 Original Jam The scanner may stop feeding the original in the scanner if the original skews b S P Pressing Scan Abort Button during scanning also deele stops the original in the scanner Scan Abort Button In both cases LED Indicator flashes red 1 Lift up both sides 1 of the Scanner Unit and then remove the original deme ege Le E Pee Ra si wr at C TEN um 2 Gently press Scanner Unit down and firmly close it A NOTE Press down Scanner Unit on both the sides to close it Do not close it by pressing only one side down 3 16 Chapter 3 Error Correction 3 1 Accessory Jam The printing paper is mis fed in the optional device such as Auto Stacker or Folder Remove the mis fed paper making reference to the User s Manual of concerning device 3 17 Chapter 3 Error Correction 3 2 Door Open XXXX Open is displayed in the UI screen when the door in each unit is opened 3 2 1 Roll Deck Deck 1 Open Close the Roll Deck securely to clear Deck 1 Open Roll Deck 3 2 2 Engine Unit Front Cover Open Close the Engine Unit securely to clear Front Cover Open Engine Unit A NOTE There is an interlock switch of the Engine Unit on both sides
36. reece teases 1 7 1 Papers VOU UW i TO ht 1 7 2 Keeping the paper in the custody SE 1 7 3 Treatment against environmental condition ier eee eet dee be 1 1 Chapter 1 Before Use 1 1 Installation Requirements The following conditions are required for installation of the equipment Qo 1 POWER SOURCE should be rated as follows In U S A 120V plus minus 1096 50 60Hz 15A or higher In Europe 220 240V plus 6 or minus10 50 60Hz 10A or higher 2 The equipment must be on an exclusive circuit 3 The outlet must be near the equipment and easily accessible Norge Kan kobles til IT strem distribusjonssystemer 1 Make sure to connect this equipment to a grounded outlet 2 For PLUGGABLE EQUIPMENT the socket outlet shall be installed near the equipment and shall be easily accessible The site temperature range 10 to 32 degrees Centigrade with the humidity between 1596 to 85 RH NON CONDENSING Keep the printer away from water sources boilers humidifiers refrigerators or kerosene oil stove 1 The installation site must not have open flames dust or ammonia gases 2 The equipment must not be exposed to the air vents from air conditioners It may affect the image quality 3 The equipment should not be exposed to the direct sunlight Please draw curtains to block any sunlight When you open the Movable Unit do not expose the Photoconductive Drum to strong intense
37. th Maximum Standard 6 000mm 19 7ft for 36 AO wide plain paper bond or 5 x Standard length plain paper bond 2 x Standard length tracing paper vellum 1 x Standard length film 64 000mm H H H H Minimum 210mm 8 5 NOTE If the print is longer than the mentioned above its image quality or the reliability of paper feeding is not guaranteed Paper feeding method 2 Roll Decks Manual Feeder single cut sheet Paper tray multiple cut sheet option Print size from Paper Tray option ISO mm Width sea 420 297 210 x x mw XI IX ANSI inch Wiath SSC RES pne oco ae 9 88 8 x j x I x j dx 2 x txt UJ dx 1x Shorter than 4 minutes 30 seconds At 23 C 60 RH the rated voltage and plain paper is used 21 seconds D Landscape Front Stacking At 23 C 60 RH the rated voltage and plain paper is used Heat and Pressure Rollers Dry type non magnetic mono component toner 1 6 Chapter 1 Before Use Recommended Media US model Bond 64g m to 80g m US Bond PB 20 Vellum US Vellum XV 20 Film 4MIL PF 4DME EU Asia model Plain Paper 64g m to 80g m Tracing Paper Gateway Tracing Paper 73g m Film NSF4mil Storage of consumables Toner cartridge Store the cartridge within the temperature range from O to 35 degrees Centigrade and within the humidity range from 35 to 8596 RH A NOTE
38. the print paper has an excess curl 3 It will become a cause for paper mis feed defective print image or paper creasing if you use a paper that does not satisfy the specification 4 Do not use a paper of which surface is very special such as thermal paper art paper aluminium foil carbon paper and conductive paper 5 Do not use papers with unpacked exposed in high low temperature amp humidity in a long period Such papers may result in mis feed defective image or paper creasing 6 Tracing paper exposed to air over a long period tends to cause a defective printing Removing one round on the surface of the tracing roll paper from the beginning is recommended Refer to 2 3 Replacing Roll Media 1 7 2 Keeping the paper in the custody Keep the paper in the custody taking care of the following matters Do not expose the paper to the direct sunlight Keep the paper away from high humidity It must be less than 70 Put the paper on a flat place If you will keep the paper in the custody which you have already unpacked put it into the polyethylene bag to avoid the humidity DOMI 1 16 Chapter 1 Before Use 1 7 3 Treatment against environmental condition Take a necessary treatment according to the environmental condition as shown below Humidity Void of image crease of paper and 1 Install the humidifier in the room and other problems occurs when you print humidify the room air with plain paper
Download Pdf Manuals
Related Search