Operating and Service Manual megaSun 7900 megaSun Cadillac
Contents
1. field once again and keep the key pressed for 0 5 seconds After a short time lag the body fan is then switched off The body fan can be switched on again at any time simply by touching the field With the help of this system you can choose the audio source e g change the CD or go to the next piece of music MP3 The MP3 player is equipped with a 256MB chip which can take the volume of the 3 music CDs The MP3 player is designed in such a way that you only have to change the chip for the music As an optional feature the music of the MP3 player can be turned on during the tanning breaks Tip The music of the MP3 unit can only be controlled by one Operation and Service megaSun 7900 Air conditioning Colour stimulation megaSun Channel selection continued audio source i e either by the chip of the MP3 player or by an external music source The choose of an other music source may be done by a BCD coded signal It is possible to select up to 4 different sources By pressing the or keys you can switch the air conditioning on or off during the tanning session Once the air conditioning has been switched off it can only be switched on again after an interval of 3 minutes A small star is displayed to confirm this If the request to switch on the system is made earlier it will be registered big star and when the interval of 3 minutes is over it will be executed automatically2. 2 Undo the screws of the tube cover in the facial area to Section 3 3 remove the tube cover 4 Liftthebasepane O lt O lt O Section3 2 Operation and Service megaSun 7900 j aae an l ln a TaM j Illustr 5 10 Dismantling the Illustr 5 11 Dismantling the tube cover filter pane frame Cleaning For a harmless cleaning of the filter panes use the special cleaning and disinfectant fluid megaClean which has to be diluted in water in a ratio of 1 13 Or use a normal glass cleaning agent with a soft cloth or a chamois leather 5 4 Tubes and facial tanners Dismantling In order to clean or replace the tubes and facial tanners please proceed as follows Step Procedure Reference Remove the tube covers in the facial area Section 3 3 _ Tilt up the base pane Section 3 2 Cleaning intervals To make sure that the tanning effect is maintained we recommend you to clean the tubes and UV radiators with warm water and a chamois after approx every 200 hours of use Do not use any aggressive or alcoholic cleaning agents Tubes in the The shoulder tanner activeFlex is equipped with 7 tubes of shoulder tanner 25 W each In addition the loudspeakers are located in this element Operation and Service megaSun 7900 megaSun ta mm m E Ta a a a s k a r See i Se i Mo D EE ue pbs cies Buse ki TU Lief f e e oe ine ee ARM Vert Rees n Veer ier bt nl hy a
3. by KBL Operating and Service Manual megaSun 7900 megaSun Cadillac BA_7900_GB_E 0707 Copyright and Trademark Printed in Germany Copyright 2004 KBL Solarien AG This documentation covers only products manufactured by KBL Solarien AG This documentation must not be duplicated photocopied translated or stored on any electronic medium or in a machine readable form neither in whole or in part without prior written consent by KBL Solarien AG For instruction updates please refer to http www kbl support de For software versions without easyCare KBL4_ 64 exe e with easyCare KBL4 ec 35 exe megaSun is a registered trademark of KBL Solarien AG Certified according to DIN ISO 14001 2 N lg 3 f KBL Solarien AG axa Ringstrakke 24 26 56307 Dernbach Germany SUNSHINE COMPANY fon 49 0 2689 9426 0 Fax 49 0 2689 9426 66 eMail megaSun kbl de Internet www megaSun de Operation and Service megaSun 7900 megaSun Table of Content o YT General Safety Instructions cccscsecccssseeseenseesensseecenseeeeoseeseensessoensessonseesees 4 PVG PIAT r a E eeu seateuctscsversuccseeeeseeds 5 eTe ai o p E E E E A 6 Operation during the tanning Session cccccsssseecseseeeeeeseeseenseeseensessonseesees 6 Bel Operating OA Nacsa crseectisa canted i aeni a ea adaa ae aaa ESE 7 A FU ON neces E E sane perenne nega A E EAE E bene natce usandaneeceoaveate A E 8 4 3 Tips for t
4. here G will stop flashing and this colour Green has been selected When all keys have been pressed all the letters will flash i e the colour stimulation has been inactivated It is only possible to choose one colour by pressing the corresponding key It is a sub menu of AAC The duration of the breaks of aroma and aqua can be set between 1 5 minutes The details are set by pressing the and keys above or below the time ust Contr a Operation and Service megaSun 7900 megaSun Audio This menu has five sub menus e EXTERN If the signal is ON an external source sends the music signal otherwise the internal MP3 player is used e VOL HOT the volume of the music or of the user guidance system when the fan is running e VOL COOL the volume of the music or of the user guidance system when the fan is not running e NONSTOP when the signal is ON the music signal is permanently amplified otherwise the music transmission ends with the tanning cycle e CH The channel selection may be changed from channel and volume selection to BCD selection of a music source It is possible to select up to 4 music sources The volume is adjusted at the music amplifier The menu can be selected by pressing the 0 and 5 keys the functions can be activated or inactivated by pressing the key above OFF or the key below ON or you can increase or decrease the
5. tank and replace the empty tank by a full one Screw the lid on again Keep clean the end of the tubes when changing the tank use a plastic bag Only use the specific water by KBL aquacool Otherwise the nozzles may clog up which might produce infections Put the constructional elements back into their original place in the sunbed Acknowledge the error message in 1 Operation and Service megaSun 7900 megaSun 8 5 Colour codes for the pipes Colour code The pipes are marked with colour points Blue compressed air for agquaCool Red reflux aquaCool Green flow pipe aquaCool Yellow aroma hype a Sry Abb 8 2 Compressor Abb 8 3 aquaCool Abb 8 7 lonizor and aroma pipes Abb 8 8 Pipes at the nozzles Operation and Service megaSun 7900 8 6 Error messages Error message Abluft oder Windschalter Error message Ende der Besonnung End of tanning session BUS Error E01BUS ABL E02 BUS TMP E04 BUS VOIC EOSBUS REL This error message is displayed on the operating panel and can be acknowledged by pressing the Stop key Prior to this service staff has to find the reasons of these error messages Possible reasons can be e temperature in the unit is too high e exhaust vent system is defectiv This message will be displayed after 40 minutes of uninterrupted operation of the tanning system By turning off the coin operated system this message
6. Exception In case that the system has been switched off by means of the coin controlled system it can be switched on again immediately Note please You will find this menu here if there is no aquaCool You can only switch on one colour The colour of the colour stimulation can be selected by means of the or key 48 power LEDs of each colour R red G green and B blue are mounted in the canopy of the tanning bed Operation and Service megaSun 7900 12 4 2 2 Other sub menus Aroma megaVoice pureAir The aroma function can be switched on by means of the t key above 0 and switched off by the key below 1 The display flashes a signal when the function is not activated KBL can offer 2 aroma fragrances Sunrise and Daydream The apparatus holds only one fragrance which can be changed very easily however The fragrance is combined with a gel Please note that the gel is not completely used up but a small rest will remain This status is shown on the display so that the operator knows when to change the gel The fragrance comes out at the foot of the bed The air stream leads the fragrance over the body to the face so that it can be perceived intensively aroma and aquaCool are activated one after the other aroma aquaCool aroma and start again and again in an interval of 1 minute Note pureAir and aroma exclude each other As long as aroma is giv
7. a doctor when your skin produces persistent swellings or sore points or when pigmented moles change their appearance Operation and Service megaSun 7900 52 The following groups of people are not allowed to use the apparatus e children e people with pace makers e people who get sunburn without tanning when exposing themselves to the sun people suffering from sunburn people who suffer or have suffered from skin cancer or who are Operation and Service megaSun 7900 megaSun 9 2 Super Power UV Type 3 inductive Tanning session Skin type Il Skin type Ill Skin type IV Time in min l l 8 9 10 11 11 13 13 15 14 17 The interval between two tanning sessions has to be at least 48 hours Max number of tanning sessions per year 15 kJ m 9 3 Super Power UV Type 3 CPI Tanning session Skin type Il Skin type lll Skin type IV Time in min 6 l 8 10 11 12 14 15 16 18 53 19 oO N O 01 amp O N The interval between two tanning sessions has to be at least 48 hours Max number of tanning sessions per year 15 kJ m Operation and Service megaSun 7900 9 4 Super Power UV Type 4 inductive Tanning session Skin type Il Skin type Ill Skin type IV Time in min C 0 IN IN O O O O1 1 2 3 4 5 6 K 8 The
8. by the studio guest e OFFSET Only applicable for tanning units equipped with ACS NOTE Contact your KBL Technical Service before making any changes within this menu item Increasing the offset value results in the fan starting at a higher speed The offset value may have to be adjusted e g in case of the thermal switch of the sunbed being triggered due to bad exhaust vent conditions in the tanning studio The offset value may only be increased after any other causes for the triggering of the thermal switch have been excluded see section Fault messages exhaust air 00 99 The offset value can be increased in steps of 10 e A START Presets the fan power level at the beginning of the tanning session Adjustable from 20 to 99 During the tanning session the studio guest can change the fan power or switch off the fan Operation and Service megaSun 7900 45 46 AR AQ Tube hours Time stamps The aroma function can be activated AR or inactivated AR_ the same goes for the aquaCool function AQ AQ The setting can be modified by pressing the or key above or below the symbol Any modifications are accepted by pressing the START key In this menu you can set the service hours of the tubes in steps of 5 hours This display has to be reset to zero after each tube replacement Attention Always carry out a reset after each tube replacement Enter the hours Here you can store the
9. display Version of the control software Sun bed type Tube type Running text The start of the tanning program depends on the studio control system If a simple coin operated system has been installed the tanning program is started by inserting coins or tokens When the warm up time has elapsed the tanning lamps are turned on automatically If the touch key Start is pressed during this warm up time the lamps turn on immediately Operation and Service megaSun 7900 megaSun The facial tanners are always switched on only after a certain delay Some of the basic features are set in service level such as colour stimulation aroma therapy time control etc Studio staff will set these options according to the customers wishes 4 1 Operating panel Illustr 4 1 Operating panel The operating panel with aguaCool shows between the keys w o aquaCool 3 8 a moving symbol animation If aguaCool is not present the symbol for the air conditioning will be displayed instead of the aquaColl symbol Main display The running text is displayed as long as the sunbed is in the waiting position When the coin controlled signal appears the functions are displayed and the sunbed can be operated by touching the corresponding keys Any input will be confirmed by a beep tone Operation and Service megaSun 7900 4 2 Functions Running time End of the tanning session A function is switched on by
10. interval between two tanning sessions has to be at least 48 hours Max number of tanning sessions per year 15 kJ m 9 5 Super Power UV Type 4 CPI Tanning session Skin type Il Skin type Ill Skin type IV Time in min 5 6 i CO N O B W N C CO 00 IN O O O A The interval between two tanning sessions has to be at least 48 hours Max number of tanning sessions per year 15 kJ m Operation and Service megaSun 7900 megaSun 9 6 Ultra Power UV Type 3 inductive Skin type Il Skin type Ill Skin type IV The interval between two tanning sessions has to be at least 48 hours Max number of tanning sessions per year 15 kJ m 9 7 Ultra Power UV Type 3 CPI Skin type Il Skin type Il Skin type IV ee e 9 11 13 14 55 The interval between two tanning sessions has to be at least 48 hours Max number of tanning sessions per year 15 kJ m Operation and Service megaSun 7900 56 9 8 Ultra Power UV Type 4 inductive Skin type II Skin type Ill Skin type IV The interval between two tanning sessions has to be at least 48 hours Max number of tanning sessions per year 15 kJ m 9 9 Ultra Power UV Type 4 CPI Skin type Il Skin type Il Skin type IV 8 10 The interval between two tanning sessions has to be at least 48 hours Max number
11. is acknowledged Daten line of the Bus C Bus is disturbed 230 V is missing at MP3 Player or Audio Switch Bus connector at MP3 Player in wrong position There is not any data link between the controller board and the revolution control Reason defective or not connected I C revolution control Reason defective or not connected C temperature sensor Solution press the START key The blower is running with max revolution during the temperature controll Reason There is not any data link between the controller board and the MP3 player Voice Solution press the START key The controller is working as one w o megaVoice Reason missing soldering bridge on MP3 Player megaVoice SD card not readable formating or wrong inserted Plug at MP3 ilnterface or at I C Audio switch is inserted uncorrect Configuration error I C Relay board 8 an I C Relais board 2 at the same time connected Operation and Service megaSun 7900 megaoun 9 Tanning instructions 9 1 General tanning instructions Different skin types react differently to sun and tanning times Follow the skin type table and the individual tanning program see p 56 ff Once you have reached your final tanning result further tanning can only be achieved by considerably exceeding the recommended tanning times This has to be avoided at all costs UV radiation from the sun or from UV apparatuses may cause damages to skin or eyes These biolo
12. may lead to damages of lamps and sockets Therefore when inserting the burners please make sure that the contact surfaces of both sockets and burners are clean Insert the burners in a straight position into their sockets Empty space Illustr 5 15 Dismantling the Illustr 5 16 Socket burners Operation and Service megaSun 7900 megaSun 9 6 Unit lighting Replacing the The lighting system is made up of 4 tubes of 58W each lighting system in e a white tube in the lower front section the canopy e acoloured tube above in the canopy matching the design colour e and two tubes for the interior in the canopy and the back The starters for the tubes are in the left socket of each tube They have to be replaced if necessary e Remove the end metal covers on the right and left of the handle rail Undo the screws of the aluminium traverse and tilt it up Illustr 5 17 e Slightly lift the inserted element loosen the velcro fastening e Pull out the inserted element Illustr 5 18 Aluminium traverse End metal cover Illustr 5 17 Opening Illustr 5 18 Lifting and pulling out the the canopy inserted element Exchanging the These tubes are located behind the tanning tubes unit lighting in the e Open the acrylic pane of the canopy or of the back interior e Remove the tanning tubes e Exchange the corresponding tubes and if necessary the starters at the left socket as well Exchanging the e Hang the base pane onto the b
13. of tanning sessions per year 15 kJ m Operation and Service megaSun 7900 megaSun Operation and Service megaSun 7900 57 58 Operation and Service megaSun 7900 megaSun Operation and Service megaSun 7900 59
14. pressing the key sequence yt ass y5 a Of the body fan You have to press the individual buttons within a period of 1 sec Please also bear in mind the possibility of defining two different illumination cycles for each day of the week see 8 2 Service level I Error message This error message is shown in the display and can be Abluft acknowledged by pressing the Stop key exhaust air But before doing so service people should repair the defect Possible reasons of this message can be e the temperature in the apparatus is too high or e the exhaust vent system is defective For more information see 8 5 Operation and Service megaSun 7900 14 5 Maintenance of the apparatus Preparatory works Before you open the apparatus switch off the fuses to discon nect it from the mains supply Do not operate the tanning unit without the front panels without acrylic panes or with the base section opened because other wise the tanner areas will overheat This will destroy the filter panes As far as CPl equipped units are concerned the electronic switchboxes located under the bed are also exposed to the dan ger of overheating 5 1 Cleaning and care Plastic parts Note Acrylic panes Fixing the canopy The bigger plastic parts are made of solid high quality ABS material On top of it you will find a hardwearing transparent PMMA layer The surfaces and the acrylic glass must not be cleaned with concent
15. B TIMER A fragrance can be sprayed off at particular times on the days of the week There is one interval Operation and Service megaSun 7900 Aqua megaSun available for each day for the setting see Timer AR CONT Shows the filling level of the aroma gel When it has reached 00 this status is also shown after the tanning session When having replaced the tin with the aroma gel this message has to be acknowledged see 8 3 and 8 4 by pressing touch key 1 These sub menus can be selected as in all the other menus by pressing the keys 0 and 5 The function is switched on by the key or off by In the same manner increased or decreased This is a sub menu of AAC Water is misted up by means of nozzles making the tanning session more refreshing AQUA ON OFF This function can be switched on by pressing the key 4 above OFF and switched off by pressing the key 8 below ON AQ TIME The spraying cycle is set in the menu CYCLE and the spraying duration in this menu AQ TIME between 2 6 seconds The details are set by pressing the and keys above or under the time display Operation and Service megaSun 7900 41 42 ain on ott Color 4 9 It is a sub menu of AAC The colour of the colour stimulation can be pre selected If you press the key above one of the letters e g G this letter
16. ate Outlet at the left hand rear side of the unit Quantity Depending on local conditions and air humidity Electric connection Wall mounted junction 2 140mm x 120mm x 70mm with PG 21 feed box see tables on the following pages 2 Amperage E Operation and Service megaSun 7900 28 Length x width x height 2380 x 1500 x 1780 mm Weight w air conditioner 590 kg 640 kg 6 2 Views 300 1875 Tn p 9 r Zz Operation and Service megaSun 7900 megaSun 6 3 Special technical data E Super Power CPI Ultra Power CPI Air velocity ca 10 m sec 4x 600W Bed 22x megaSun Ultra Power 22x megaSun Ultra Power R 100 W Longlife CPI R 160 W Longlife CPI Rated capacity 12000 W 13200 W w air 13600 W 14800 W w air es condition Fuses pole fuse protection 3 x 25 w residual current operatec circuit breaker Fl Operation and Service megaSun 7900 29 30 7 Wiring diagrams 7 1 Mains voltage Fuses and residual current operated circuit breaker FI The unit has to be connected to the 400 V mains the connection is to be protected by fuses For details on the fuses please refer to the section Technical data An FI protective switch is required in any case KBL Solarien AG recommend the following type KBL 3200 0770 OO Should any interference occur due to the operation of your tan ning unit with the mains e g with ripple control systems TRA consu
17. ay Ale rT ret eee ca SU WA ae a Illustr 5 12 Shoulder tanner with Illustr 5 13 Series apparatuses and loudspeaker open starter for shoulder tanner open Illustr 5 14 Shoulder tanner closed Replacement Tubes facial tanners and starters have to be replaced only by intervals those of the same type When installing the tubes make sure that the inscription is visible i e the reflector must be at the back For units equipped with CPI technology it is essential to carry out a reset after each tube replacement see Section 8 3 For units equipped with inductive technology shoulder tanner also install new starters when replacing the tubes CPI Mode 750 hrs 500 600 hrs 800 hrs 500 hrs 19 Operation and Service megaSun 7900 20 5 5 Dismantling the burners Dismantling Attention Only trained expert staff is allowed to install or remove the burners Take the burners with a soft cloth and pull them out towards the front Do not touch the burner glasses or the reflector surface with your bare hand Illustr 5 15 If necessary you can clean the glass bulb and the reflector sur face with an alcoholic cleaning agent The connecting elements of the burner are not all the same thickness When inserting the burner into the socket the metal clamp is directed to the right to the empty space in the middle of the reflector Illustr 5 16 During service dirt accumulation and an incorrect positioning
18. c ln Sunday SU emn Enter the PIN Il gt correct PIN w a Aqua Color Cycle f megaSun Timer A ON Timer A OFF Timer B ON Timer B OFF lt _ gt gt T gt Serviceebene Il eet cee A Solar ON OFF Aj Booth ON OFF B Inter 00 h Gate ON OFF B Timer AR Cont 99 ON OFF AQ Time Operation and Service megaSun 7900 37 ams VOL HOT COOL NONSTOP CH PULS BCD Overview On this level you will find the following menus Selection of menus by pressing keys 5 and 0 8 2 2 The menus on service level Operation Info In this menu the service hours of the sunbed WORK and the burning time of the tubes TUBE are displayed b ee TY 5 v c a eee see O e m a gt gt ov o u 2 es j a i S p gt ee 6 v gt gt J a 7 i me SS amp gt ase t se ese sgte st s gt n E i S m gt gt t t J s i B gt 4 3 p s ae v _ 5 se ee TT s 38 With the START key you open the sub menus With the STOP key you go back one level higher If you have changed a value and you will safe it press START Operation and Service megaSun 7900 megaSun CPI In this menu the service hours of the sunbed WORK and the burning time of the tubes TUBE are displayed ga O Enter the CPI moce D Confir
19. ece ack dancse enn ta eheeedanniseeee cosa soeeauen te 28 WINO CAGE aN S sga a EEEE 29 Tal Mans voltage s sxtonarsonsiicead seirec tend gute oume ee i a E NTEs ear EAE AERE E Aa Raae A 29 7 2 megaVoice without MUSIC OPTION senscrcssccsussctoninercancreneererdadenennseandsneecnedianadeenavdarweneeatdnednensdvens 30 7 3 Internal MUSIC signal MP3 player sscaiivndsnnucsunadsnnnesaabasunddrandanitilertadacnmmeiadanmamanaliadhdacendantiiinadians 30 7 4 External music signal without channel selection nnsnneenenennsnnesrnnsnrrrrenrnrsrreenresrreenrennne 31 7 5 External music signal 100V without channel selection naannnennnnnnnenennnsnnnnennnsnnnnnnennnne 31 7 6 External music signal with channel selection cc ccecceccceeeeeeeeeeseeeeseeeeseeeeseueeseueesseeeeaaess 32 lat EXMA TET issie E Si 33 SLE A 0 e EE secrete E E A E E EE EA E 34 8 1 General information and structures nannsnnnesnnenneennoernnnrrsrrnsnrrnrrrenrnnrrnnrrsnrrenrrsrrnenrnnrns 34 o2 SNNN e en E A E A EEEE 35 9 3 SVC level Hieuisonreiroinonneti e a a i EE aa aa eia a NE i iE OENE 42 8 4 Re filling Changing Aroma and aquaCool cccccceeececeeeeeeeeeeeeeaeeeeeaeeeeesaeeeeaeeeesaeeeeeeaes 46 8 5 Colour codes for the PiPe ccccccsccccssececeseeceeeeceeeeseaeeseaeeceaeecseeeseeeseeeseueesegeessneessneees 47 36 Enor message sia a eee TE NT eee reer 48 Tanning instructions sssssssnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnn
20. en off pureAir will be switched off The Voice function can be switched on by means of the key above 0 and switched off by the key below 1 The display flashes a signal when the function is not activated megaVoice informs the customer in a simple and short way about the operating functions of the sunbed If requested megaVoice can be switched off by the customer during the tanning session The pureAir function cannot be switched on or off by keys Note pureAir and aroma exclude each other As long as aroma is given off pureAir is switched off During the tanning session nozzles at the foot of the bed produce cleared ionized air which is led over the whole body Here as well the air is led from the foot of the bed over the whole body thus reducing tanning odours lonizer for the pureAir function is mounted in the foot Operation and Service megaSun 7900 megaSun 4 3 Tips for the studio operator Daily checks and Please make sure basic settings e that the tank for the condensed water is checked and emptied every day e that materials which have been used up are refilled 8 4 and e that the settings which can be executed in the service levels see 8 3 of operation e g colour stimulation aroma time controls etc are made Please observe Section 2 of the Service Plan Illumination after The illumination decorative may be switched on or off if the use timer signal is not active by
21. es Service levels There are two service levels which are both accessible by passwords Io get into these levels and to release processes the touch keys 1 O have to be pressed For that purpose the plus and minus keys bear numbers which in the illustration below are slightly bigger than in reality In order to get access to the service pages two prerequisites have to be fulfilled e there must not be any error message on the display e there must not be any incoming signal from the coin token box system In case there is an error message you need to reset this message by touching the Stop sensor field Illustr 8 1 Touch keys 1 O for service operations Service level In order to get access to level I first enter the sequence 1 6 1 andthenPIN1 1 1 1 Service level Il This level comprises service pages that may be used by Technical Service staff only Starting from level Il menu PIN II you will get into level II by entering the correct PIN not1 1 1 1 General navigation When having called up service level the following keys can be used as follows Key 5 to move forward in the menu Key 0 to move backwards in the menu Stop key to leave service level or menu Start key to select a menu item or to save the value displayed Operation and Service megaSun 7900 8 2 Service level 8 2 1 Structure of the menu on service level Operation Info lt Working Hours CPI ES Mode P SP eas CPI RESET orca w
22. gical effects depend upon the quality and quantity of the radiation as well as on the skin and eye sensitivity of the individual customer Sunburn can be a reaction of the skin after excessive radiation Excessively repeated exposures to UV radiation from the sun or from UV apparatuses may lead to premature ageing of the skin and increase the risk of getting skin cancer Unprotected eyes may become inflamed on their surface or in some cases e g after a cataract operation the retina can be damaged after an excessive UV exposure Cataracts may develop after many repeated exposures Special care is necessary in cases of pronounced individual sensitivity to UV radiation and in cases where certain medicines or cosmetics are applied It cannot be said in any case that the use of a sunbed reduces the risk of getting sunburn The apparatus must not be operated when the timer or the filter panes are defective The following safety precautions have to be taken Safety precautions e Always use the goggles provided e Remove any cosmetics before the tanning session and do not use any sunscreens Refrain from tanning when taking medicine which increases the sensitivity to ultra violet radiation If in doubt ask your doctor for advice Allow a period of at least 48 hours between the first two tanning 51 sessions do not sunbathe and use the apparatus on the same day Follow the recommendations concerning tanning times and tanning intervals see 56 ff See
23. h safety timers which comply with the corresponding standards KBL Solarien AG recommends the following timer mega Timer KBL Article No 9100025000 Before opening the apparatus switch off the fuses to disconnect the system from the voltage supply Do not operate the sun bed if a filter pane is defective See Section 5 3 Attention High light intensity do not look into the radiators The data indicated in the tanning schemes are based on the assumption that both tubes and burners are replaced at regular intervals See Section 5 4 When replacing tubes remember to reset the CPl control system and the counter of the tube service hours The canopy drive has to be serviced regularly with each tube replacement This also includes the replacement of the drive rope after 3 000 hours of operation See Section 5 8 Do not use any cleaning agents other than the ones approved by KBL Solarien AG See Section 5 1 Operation and Service megaSun 7900 megaSun 2 Service Plan Service intervals For a safe operation of the sun beds regular service works are essential and have to be documented Cleaning works have to be done when necessary and do not have to be documented Service hours What has to be done Every day Check the filling level of the condensate tank and empty it if necessary 100 Change or clean filter mats 500 600 Change burners For inductive apparatuses e Change tubes e Change starters e Reset counter of service h
24. he studio operator sie ton seceiseas ricsentonateesextcen nstennoetecacanhsersecdushactteerdahassuscadanntescdesetts 13 Maintenance of the apparatus ccccccesseeeesseesseeeseeenseeenseeeaseeeneeoeaeeoeseeoneeens 14 Ot Cleaning and CIG sransisiahenes ii g E a Sa 14 5 2 Dismantling the acrylic panes esi ccincredactsudcasdacewadariod uctiodiedeusendvsivacsapediahid eeaibddaladenabucse dadcentosilices 15 MIC INS aie ere ai cde Sic css ct ssn cc sinerewis apenas see EEE ET EE 17 5 4 Tubes and facial tanners ccnahescedsdecesadsiviueionssecesGes nee bauebeacawietenacedeeisatengueuciawaadilesiesadduencteened 18 99 Dismaniing the DUME S savin inicconenairsicoiaciysinassadersaanisantiaocaminaunedmatuecsusias eeu OE 20 o0 UALIORIN J eeen a E a E nA 21 A al U2 ar AE E A E A A E eee ere 22 309 CANOPY ONV seisisanornr aE na E eane Ea aaia e ee i er AEE 22 5 9 Ex austair systemi Santee sntecatiansnctauaiprlaeeumiadscleswitane EEE EEA n EAE EREA EA EA Eaa EAE ERAS 24 5 10 Air conditioning unit and condensate pump cece ceecceececececeeeeeeese cece eeseeeeseeeseeesaeesaeeeaes 24 5 11 Replacing the AQUACOOI nozzles cccccccccseecceneccenecceneeceueeccueescueessaeeesageesaueessaeecsesesauees 25 Technical data ie E a 26 6 1 Data which all the apparatuses have IN COMMON ccccceccceecceeeeseeeceeesaeeeeeeeseeeseeeeaeeeaes 26 O VON a A E E E AE E E E E 27 6 3 Special technical data cee se deie cece es caectseee coe edd eset secant c
25. ill be reduced step by step e the LEDs in apparatuses with activeColor will shine in the colour adjusted for another 20 seconds Operation and Service megaSun 7900 Extended menu Music channel Air conditioning Colour stimulation Aroma Acoustic user guidance Volume aquaCool empty megaSun These double arrows point to some more menus which can be activated by pressing the or keys The following menus are available which will be explained in more detail below By calling up these additional menu functions you can see which functions are activated after switching on the apparatus 1 Special customer requests can be pre selected in the service menu see Section 8 3ff You can adjust the volume of the music by touching the and yy Keys The volume will be displayed in the numerical field as a value between 0 99 Press the corresponding sensor key Here you can activate the aquaCool water atomisation func tion plus button symbol flashes or deactivate it minus button symbol does not flash Default setting at start as defined on service level in the AAC Aqua menu e If the aquaCool supply is running low the message Aqua low is shown on the display between the tanning sessions When the message appears for the first time the aquaCool supply will last approx another 2 5 hours of operation with aquaCool e Ifthe aquaCool supply is empty the message Aqua 0 ap pear
26. lt your power supply company regarding the installation of corresponding blocking elements audio frequency suppressor 400V 3N 50 Branch box with fuses see Technical Data and protec tive circuit breaker type FI KBL 3200077000 PE N L3 L2 L 9I QOOUOC 7 UH e e o gnge f blau 9 Q I Q PE N C3 L2 L1 megaSun 7900 Bee ee es ees ee Operation and Service megaSun 7900 7 2 megaVoice without music option Music amplifier Via an interface card the MP3 player megaVoice is connected 3220 2885 00 to the music amplifier which leads to the loudspeakers connected in parallel equal phased Music amplifier Interface 3220 2885 00 ess woe 3 ae board L egoog LZ seals M 3220 3230 60 EN panan E8 6 5 ware 2 1 7 3 Internal music signal MP3 player Music amplifier MP3 player and megaVoice are connected to the Audio switch 3220 2858 00 which leads the music signal to the amplifier and then to the loudspeakers connected in parallel equal phased FPA Musik amplifier 2C Audio MP3 A FL Se TIIT a 3220 2885 00 switch megaVoice Tae ole 3220 3230 20 3220 3222 95 E8 6 5 241 MP3 Music 3220 3222 90 Audio switch MP3 Music A EF j sa E E a aiit Bl i H a os vy Fet al gt IEC q fi ou By 1 r i os ty 5 7 r 1 h ao T p i m ra wa a4 a Operation and Service megaSun 7900 31 7 4 External music signal 100V without channel
27. mation Bi LS CPI Reset os Timer This function allows you to specify two times for switching on and two times for switching off the decorative lighting for any day of the week If you do not need the switching time you can delete it by pressing key 1 The hours are set using keys 2 4 and the minutes with the help of the keys 3 8 ee 2 PT i e oe Bi bee meets ale l 39 Operation and Service megaSun 7900 Time Date This menu shows time and date Both values can be changed PEAS ee i shoes i pp TT TE TTT b os C E i TE a s o ne S a a a H M H 5 E 3 a 4 Pa m ct a E 1 k m E T 7 a I Baa t i Bs 4 s Enni a f i E p n a a Eo m 4 i L a a E E k a ia E i z a Te a J i E ETT CLI T a ae CELE Ee i J b a E 1 x Change the time AAC This menu has four sub menus e AROMA e AQUA e COLOR e CYCLE which can be selected as in all the other menus by pressing the keys 0 and 5 Aroma This is a sub menu of AAC and it has also 6 sub menus e SOLAR ON OFF A fragrance is or is not sprayed off on the sunbed e BOOTH ON OFF A fragrance is or is not sprayed off in the booth e B INTER xx h Selection of the cycles per hour when the fragrance is sprayed off It can be adjusted to times between 00 h and 24 h e GATE ON OFF A fragrance is sprayed off in the booth when the door is opened or closed e
28. nnel selection To connect the music signal use a 2 pole shielded cable the shield has to be earthed at the signal source The cable is connected to the marked clamps of the Audio switch The potentiometer is used to set the signal The loudspeakers are connected in parallel equal phased Se aa oe oy ores tes Sey Oey se isa Ly 4 Epa i q ADE 5 J HRAT f EES L ego09 ir eeoTd Music amplifier lC Audio MP3 rae T 3220 2885 00 switch megaVoice 3220 3230 20 3220 3222 95 E86 5 21 E zo ma Di Channel ei Processor selection ft he 3220 3110 00 shielded cable Audio switch lie Masse L Music signal D a e e e e a e a a G a a a 100V Signal If the external music signal is a 100V signal the transmitter is introduced into the signal path in front of the Audio switch see 1 4 Operation and Service megaSun 7900 megaSun 7 f External Timer Timer The timer has to be connected as follows The individual specifications and wiring diagrams of the different types of timers have to be observed A door contact is necessary for the option cabin fragrance Se es ee eee ee F Door contact lt Se eS a l es os ee ee fe ee ee ee es ek eee J L1 N Wire No tea Cable Olflex 7 x 1 mm J EE KR ae EE Py Pandy PE o N L1 Control DA 4 Start 230V 2A megaSun 7900 Operation and Service megaSun 7900 35 8 Service 8 1 General information and structur
29. nnnnnnnnnnn nnnm 49 9 1 General tanning INSUUCTIONS iiciisessccsccsnedsmsnstonnettucsancnansepacmetdsiagemaenhadedenedbbbedoabaidedaiananinnadecaids 49 9 2 Super Power UV Type 3 inductive ccc cccccccccseeeeceeeeseeeeceeeeseaeeseaeeseaeeseusesseesseeessaeeees 51 9 3 Super Power UV Type 3 CPI sciccsssndassecscsucssgonncudiondsaavastices st odesehssgadaensscancsepebaes anesaanecsangbege 51 9 4 Super Power UV Type 4 inductive cc ccccccccceeeecceeeeseeeeceeeeseaeeseaeeseaeesseesseessaeesseeeees 52 9 5 Super Power UV Type 4 CPI oniccccadicsionwesancnemanactecsnedendsuttenandudesiesenasseseddassdneubeocadiexmendacecnionenss 52 9 6 Ultra Power UV Type 3 inductive 0 nnanannnennennnnnnnnnnnnrnnnnrnnrnnrnrnnnnrsnrnnrrerrerrnrrnnrrnrrerrenene 53 9 7 Ultra Power UV Type 3 CP ance ee ee eee mn eer a nee nT er anaes ee eee nee meee ee ree 53 9 8 Ultra Power UV Type 4 inductive 0 cccccccceeeeseeeceeeceeeceseecaeecaueceueecseesaeesaueseaeesseessaneees 54 9 9 Ultra Power UV Type 4 CPI cccccccccssccccseecenseceeeceaseecaseecaeeeseeeseaeeseueessusessueessgeessaeeees 54 Operation and Service megaSun 7900 1 General Safety Instructions Please observe the following safety instructions Tanning times Timer Disconnecting Facial tanner Technical parameters Mechanics Cleaning Please keep to the recommended tanning times see Section 9 The apparatuses may only be operated wit
30. olted open canopy unit lighting in the e Loosen the bolting of the lower part of the bed and tilt up front section the bed Illustr 5 20 Illustr 5 22 e Now you can change the tube If necessary take the opportunity to exchange the starter at the left socket as well Operation and Service megaSun 7900 21 22 5 7 Filter mats Cleaning intervals Filter mats in the canopy The cooling air is drawn in through two dust filters Depending on the installation site clean the filter mats or if necessary re place them after approx every 100 hours of service To ensure a trouble free service of the unit exclusively use original spare filter mats Take the opportunity to check the heat exchangers of the air conditioning unit as well to see if they are dirty Section 2 Dirty heat exchangers considerably reduce the capacity of the air conditioning unit Vacuum clean the heat exchangers if neces Sary Take one end of the handle below the filter mat to pull it out Push the new filter mat over the whole length behind the edges of the handle Illustr 5 19 Exchanging the filter mat above and below Filter mat in the base section The filter mats are located in the lower front section When the front cover has been removed you have free access to them and you can exchange them 5 8 Canopy drive Regular maintenance In order to guarantee a trouble free operation of the canopy drive check and service the
31. order Make sure that the frame is correctly positioned in the hinge When closing the pane all air nozzles must be matching their counterparts If not carefully push the nozzles concerned into their proper position Head cushion used as a padding Illustr 5 4 Loosen screws Illustr 5 5 Opening the acrylic panes Base and duct pane The following table shows how to clean the base and duct pane The electronic parts installed underneath the bed must not get in contact with any moisture Therefore in order to clean the underside of the base pane the duct pane and the inner base section use a slightly damp micro fibre cloth only Operation and Service megaSun 7900 15 Procedure Reference Open the canopy bolt it see 5 1 Undo the two pan head screws of the base pane Always make sure that you take the pane in the middle and use the hook to hang the pane onto the fixed Canopy Take out the duct pane and lay it down in a safe place Open the bar to lift the complete base case if Illustr 5 6 necessary In the centre of the lower front cover there is a square Illustr 5 7 bolt Place the enclosed key onto this square element Unlock the bed by turning the key anti clockwise By doing so the bed will slightly go up Bar Illustr 5 6 Placing the key Illustr 5 7 Bar of the bed frame Closing the base After cleaning the base pane close it again Make sure that the pane duct pane is in
32. ours For CPl apparatuses with burners in Power mode e Change tubes e Reset counters 8 e Reset counter of service hours Check and grease ropes of the canopy drive Check all inner tubes and if necessary change them Climatic apparatus e Clean heat exchanger e Check the functioning of the condensate pump For CPl apparatuses with burners in Eco mode or for CPI apparatuses without burners in Power mode e Change tubes e Reset counters 8 e Reset counter of service hours For CPl apparatuses without burners in Eco mode or with megaSun CPIl tubes in Power mode e Change tubes e Reset counters 8 e Reset counter of service hours Replace aquaCool nozzles For CPl apparatuses with megaSun CPIl tubes in Eco mode e Change tubes e Reset counters 8 Reset counter of service hours Operation and Service megaSun 7900 3 Equipment S standard O optional CPI S Electronic series equipment ACS S Control of switch on switch off behaviour activeColor O Colour stimulation in red green or blue Aroma and Fragrances in the sun bed and in the cabin cabinBreeze Music MP3 player witha 256MB memory for music Waste air tube OG 300 mm 3m conan a N 4 Operation during the tanning session General When switching the apparatus on the following information is information displayed for 2 seconds before the running text appears Firmware version of the
33. pressing the plus sensor which is also used to increase the output stepwise To set the maximum value e g fan speed the sensor field has to be pressed again and again until the maximum value has been reached A function is switched off by pressing the minus sensor which is also used to decrease the output step by step To set the minimum value e g volume the sensor field has to be pressed again and again until the desired value has been reached You can use this touch key to switch the apparatus on during the warm up time If the tanning session has been interrupted by means of the Otop key it can be continued after touching the Start key once again provided the coin operated counter has not run down yet The numerical display shows the tanning time When the tanning time is over the running text will appear again By pressing this touch field for at least 2 seconds you can terminate the tanning session prematurely During the tanning program the running time is displayed in this field When adjusting the volume the value set between 0 99 will be displayed in this field for a short time When adjusting the fan speed the value set between 20 99 will be displayed in this field for a short time As soon as the tanning time is over a program to shut down the sun bed will be started e asoft voice reminds you of the end of the tanning session and says good bye e burners tubes and the ventilation system w
34. rated disinfectants or solvents or other liquids that contain alcohol The manufacturer cannot be held liable for any damages caused by chemically active agents such as inappropriate cleaning agents To clean the varnished and plastic surfaces use a damp soapy cloth It must be avoidted at any rate that cleaning fluid runs into the apparatus For a harmless cleaning of the acrylic panes use the special cleaning and disinfectant fluid megaClean to be obtained from KBL which has to be diluted in water at a ratio of 1 13 The canopy can be fixed in the upper position to perform service and maintenance works To do so open the canopy and move the bolt at the right back to the front If you push the bolt to the back the canopy will be released After removing the screws on the left and on the right the bed pane can be fastened to the canopy For that purpose use the hook and hang it into the opening in the centre between the filter mats Operation and Service megaSun 7900 Illustr 5 1 Fixing the canopy megaSun Illustr 5 2 Releasing the Illustr 5 3 Opening for canopy hook 5 2 Dismantling the acrylic panes Dismantling the pane in canopy and lateral part Remove the screws and tilt down the panes Always put the pane frame with a soft padding e g a head cushion on the bed For service works it is possible to take out the complete frame in the lower position from its support Mount the pane in reverse
35. s and the symbol is crossed out If the system is to be used without aquaCool you can switch off the messages and the symbol For this purpose set the submenu Aqua to OFF To reach this menu proceed to the AAC menu on service level Il Operation and Service megaSun 7900 10 Facial tanners Body fan 4 2 1 First sub menu Channel selection Level Il Once the tanning program has been started the facial tanners are switched on automatically at maximum setting Levell To reduce the output to level use the field Level O To switch off the facial tanners completely touch the field again for at least 3 seconds By touching the field you can switch the facial tanners on again or you can increase their output When the system has been switched off there will be a time lag before you can switch it on again due to the necessary cooling of the burners The power of the body fan can be increased or reduced by steps of 10 by touching the fields or After being switched on the fan starts running at the power level value that has been entered for ACS A START on level II of the service menu When changing the value the current setting is displayed as a two digit number between 20 minimum and 99 maximum in the numerical field for a short time In order to switch off the body fan completely press the field several times until the value of 20 appears Then press the
36. selection 100V Music signal For this application you will need a transmitter type 9100017000 and the music signal is connected to the clamps Transformer IN 9100 0170 00 IC Audio MP3 Music amplifier 3220 2885 00 switch megaVoice 3220323020 3220 3222 95 E8 6 5 21 SS ane 00o B Audiosignal pA Ubertrager Q LZ L Transformer Music signall__ 7 5 External music signal without channel selection To connect the music signal use a 2 pole shielded cable the shield has to be earthed at the signal source The cable is connected to the marked clamps of the Audio switch The potentiometer is used to set the signal The loudspeakers are _connected inparallel equal phased_ r Music amplifier l2C Audio MP3 3220 2885 00 switch megaVoice F865 24 3220 323020 32203222 95 Be OO OO Masse ext music signal I Operation and Service megaSun 7900 megaSun The following diagram shows the wiring of the channel selection on the audio equipment s side Wiring on the audio system of the studio Puls Coding Q pra O oO v oO Cc Ke O Q O channel selection O Control voltage O Volume Wiring on the audio system of the studio BCD Coding O channel selectio O channel selectio O Control voltage Operation and Service megaSun 7900 33 34 7 6 External music signal with cha
37. sion is over this sequence is repeated 3 times tanning session ann oy sump LLL The tube for the condensate should be mounted not higher as in the tanning bed power of the pump Operation and Service megaSun 7900 25 26 5 11 Replacing the aquaCool nozzles After 1000 hours of operation the aquaCool nozzles have to be replaced in order to ensure that aquaCool stays fully operative and efficient The installation instructions will be enclosed in your spare parts consignment 5 12 Uploading to the SD card Please refer to the section Technical data for information on supported card capacities as well as file system and MP3 for mats 1 Insert card into the computer s memory card reader 2 Copy the files to the card If you would like to have the tracks played in a specific order you have to number them accordingly beforehand 001_ Titel mp3 002 Titel mp3 etc Then format the card and upload the numbered tracks For writing the card you can use ID3 TagIT for example www id3 tagit de 3 Insert the card into the MP3 player of the sunbed Operation and Service megaSun 7900 megaSun 6 Technical data 6 1 Data which all the apparatuses have in common A board with the following information has to be permanently fixed on the cabin wall near the apparatus Ambient conditions Installation site in dry rooms with sufficient air supply and ventilation Ambient temperature 30C Condens
38. spring ropes each time the tubes are replaced For that purpose you will have to open the bed see Section 3 2 Operation and Service megaSun 7900 megaSun by RBL Procedure Reference In the centre of the lower front cover there is a square bolt Place the enclosed key onto this square element Unlock the bed by turning the key anti clockwise By doing so the bed will slightly go up Open the bed completely Check the ropes for wear If individual wires of the Rope Set rope are spliced always replace both ropes KBL 5100001500 Lubricate the ropes in the area of the turn around included in set rolls in the base frame and of the eccentric discs in KBL the canopy using rope grease type HHS 2000 KBL 5100001500 Illustr 5 20 Bed lifted up Illustr 5 21 Bed half open Illustr 5 22 Bed completely open Tightening the If the canopy does no longer remain firmly in the upper position springs the two springs have to be re tightened For that purpose you will need a spanner type SW19 23 Tensioner at the left side Tensioner at the right side Operation and Service megaSun 7900 24 Close the bed Step Procedure Reference Turn the key in the middle of the lower front cover clockwise as far as possible The bed is drawn to the base part and is bolted firmly again 5 9 Exhaust air system Check connecting With each tube replacement check the connecting hoses hoses vis
39. the correct position Procedure Reference If you have opened the bolt of the base case re bolt it again Turn the key in the middle of the lower front cover as far as possible clockwise The bed is drawn to the base part and is bolted firmly again Place the duct pane back into its place and make sure that it is in the correct position Release the base pane and tilt it down fasten the pane with screws Operation and Service megaSun 7900 megaSun 5 3 Filter panes Safety function The facial tanners are equipped with an additional safety function Behind each of the filter panes there is a safety switch that switches off the burner if a pane is missing or broken Do not operate the tanning system with a defective filter pane Carry out regular visual inspections Filter panes have to be replaced only by those of the same type The filter panes may be dismantled and replaced by trained expert staff only Filter panes inthe The following table shows how to dismantle the frame of the canopy filter panes Step Procedure Reference 2 Undo the screws of the tube cover in the facial area to remove the tube cover B Also hold the front frame when undoing the screws Now you can take it out as well Illustr 5 8 Dismantling the Illustr 5 9 Dismantling the tube cover filter pane frame Filter panes inthe This frame is to be dismantled as follows lateral part 17 Step o Procedure _ Reference _
40. time stamps of the first and last download of the software a a Ces i EEEE Operation and Service megaSun 7900 megaSun Test You can also test the three functions Aroma aquaCool and aquaExtra without a tanning program After selecting a function press key 1 to start the test aquaExtra is switched on by the key 4 and off by the key 9 The cycle time is 5 min It is use to check the quality of aguaCool Version The version of loaded software is displayed since vers 4 8 This is analogue to the display after the rst start The version depends on the sunbed without easyCare here 5 3 or with easycare here 1 8 Sub type of the sun bed Operation and Service megaSun 7900 47 8 4 Re filling Changing Aroma and aquaCool Gel SUNRISE and The gel tin and the water tank are in the base part between the DAYDREAMS air conditioning unit on the left and the electronics system on aquaCool the right Procedure Reference Open the lower front cover and regularly check the filling level of the water tank and of the aroma tin When the content of one of the container has been used up replace the corresponding container Pull the holding element of water tank and aroma tin forward Move the covering handle on the lid of the Hi aroma tin to the left 1 and then move the AF lid upward 2 Now you can replace the tin Unscrew the lid with the hoses from the
41. ually Defective hoses have to be exchanged Maintenance A clean and trouble free exhaust air system prevents the apparatus from overheating Step Procedure Reference 2 The air hose of the air conditioning unit must not have i S any kinks and must be able to blow the air off freely i The maximum hose length of 6 m must not be l exceeded unless there is an additional ventilator 5 10 Air conditioning unit and condensate pump Checks Check the heat exchangers of the air conditioning unit for dirt particles each time a tube is replaced Dirty heat exchangers reduce the performance of the air conditioning unit Open the bed Section 5 8 and vacuum clean the heat exchangers if necessary Operation and Service megaSun 7900 Maintenance Note megaSun Check the function of the condensate pump each time a tube is replaced Open the bed Section 5 8 and slowly fill the tub of the air conditioning unit with water Make sure that the water is pumped off periodically For this test the unit must be connected to the mains supply By a regular and proper maintenance of the apparatus you make a substantial contribution to the safety of the system and to a long period of trouble free operation Illustr 5 23 Air conditioning unit and condensation pump The condensate pump is controlled by the processor in such a way that during the tanning session it is switched on every 5 minutes for 20 seconds each After the tanning ses
42. values by pressing above the numerical value 43 Operation and Service megaSun 7900 44 8 3 Service level Il 8 3 1 Structure of the menus in service level ll ee amp Configuration eee Aircon Configuration OFFSET ACS A Start Adjust of the tube hours Time stamp Display 1st download Time Display Date Zero or start value Time stamp last download Conguration P gt aquaCool aquaExtra Release gt Software release UV type device Operation and Service megaSun 7900 megaSun 8 3 2 Menus of service level ll Configuration menus In this menu functions can be activated or inactivated This makes sense when the corresponding function is missing or temporarily not available faded out C Channel Music channel M Music Volume A Air conditioning B Facial tanner The setting can be changed by pressing the or key above or below the symbol If the two dots behind the letter are at the bottom the respective function is inactivated C no channel selection possible B facial tanner can be operated This menu has three sub menus Aircon OFFSET and A START e Aircon Presetting for the air conditioning unit in tanning mode e ON The air conditioning unit starts automatically as soon as the tanning session is started e OFF The air conditioning unit starts operating only if it is activated
Download Pdf Manuals
Related Search