Home

owners manual-750-880-NEW

1. orange brownish colors iron blackish colors manganese slimy blotchy colors decaying organisms When hydrogen sulfide comes from a source that discolors the filter cartridge and creates a strong rotten egg odor the only recommended solution is to change the filter cartridge Milky color in the water is typically caused by air bubbles in the water Higher than normal water pressure through the DWS can create these small air bubbles but they do not affect system performance Air in the water may also be the result of conditions in your municipal water supply For countertop systems turn on the water and engage the diverter valve while slightly reducing the water flow Less water pressure through the system can prevent air bubbles from forming Black calor in the water is typically caused by residual carbon dust from the filter Allow water to run through the DWS for approximately 30 minutes to flush the filter Residual carbon dust may initially color the water black The filter is designed to restrict its flow rate when clogged with particulates or other solid contaminants When the water flow rate slows to the point of inconvenience it is time to replace the filter cartridge If other water sources are on while using the DVS turn them off to check if they are affecting the flow rate The carbon block filter may have become saturated with the tastes and odors treated in your drinking water To resolve this chang
2. bottom of the DWS Carefully set it aside remains in place on the bottom half of the housing Remove the old filter cartridge from the top half of the housing by rotating it counter clockwise if facing the inside of the top half of the housing Dispose of the used filter in your waste container that it is not cracked or worn Multipure recommends that the cushion be replaced every two to three years from around the new filter Ks bber Cushien _ turn to half of the DWS Rotate the cartridge clockwise to tighten if facing the inside of the remove top half of the housing Make sure that the cartridge is threaded properly and straight DO NOT OVERTIGHTEN half Replace the Locking V Band making sure the screw is in place to connect the band together Make sure that the V Band is tightly secured evenly around the housing top and turn to bottom connect To resume normal use of the DWS proceed to 3 7 Preparing and Operating Your Drinking Water System 19 4 4 Resetting the Capacity Monitor or Changing the Batteries Resetting the Capacity Monitor After changing the drinking water system filter the capacity monitor must be reset to its original capacity Press and hold the check reset button on the Filter Monitor Unit FMU for three 3 seconds You should hear a long audible sound 2 The LED on the LED Display Plate will blink green for one 1 second with an audible sound then blink green and red for
3. 0 15 10 0 010 LEAD pH 9 5 21H58 3955 0 13 10 0 010 LINDANE 99 0 055 0 00001 MERCURY pH 6 5 gt 9 0 006 10 0 002 MERCURY 8 5 gt 9 0 006 10 0 002 METHOXTCHLOR 99 0 050 0 0001 Methylbenzene see TOLUENE eter 0 078 0 001 Monochlorobenzene see 9996 0 077 0 001 MTBE methyl tert butyl ether gt 0 015 20 5 POLYCHLORINATED BIPHENYLS Aroclor 1260 HHB Oo 0 01 109 0 0005 PCE see TETRACHLOROETHYLENE 9996 0 091 0 001 PENTACHLOROPHENOL gt 9 0 096 0 001 Perchlorobutadiene see HEXACHLOROBLUTADIENE S 9896 0 044 0 001 Propylene Dichloride see 1 2 DICHLOROPROPANE 99 0 080 0 001 RADON 44 990 4000 1000 peeve alli pov SIMAZINE 2HUn 0 120 U O04 Silvex see 2 4 5 TP gagro 0 270 0 0016 STYRENE vinylbenzene 99 0 15 0 0005 1 1 1 TCA see 1 1 1 TRICHLOROGETHANE goro 0 084 0 0046 TCE see TRICHLORGETHYLENE 9996 0 190 0 0010 1 1 2 2 TETRACHLOROETHANE gt 9 0 081 0 001 TETRACHLOROETHTLEME 99 0 091 0 001 TOLUENE hMethylhenzene eter 078 0 001 TOXAPHENE gt 92 9 0 015 1055 0 009 Toxoplasma see CYSTS 99 95 minimum 50 000 mL 99 9596 2 4 5 iSilvexy ggi 0 270 0 0016 TRIBROMOACETIC ACID 8 0 042 0 001 1 2 4 TRICHLOROBENZENE Unsymtrichlorobenzene 9996 0 160 0 0005 1 1 1 TRICHLOROETHANE i 1 1 1 TC A gow 0 084 0 0046 1 1 2 TRICHLOROETHANE H 0 150 0 0005 TRICHLOROETHYLENE 99 0 180 0 0010 TRIHALOM
4. Connect the included Outlet adapter MC720 to the system housing s labeled Outlet port Rotate the adapter clockwise first by hand then using a wrench to tighten onto the system Housing Top Connect the Tubing to the Outlet Port 1 Using wire cutters or a knife cut square cut the tip end off of the blue plastic tubing blue tubing either connected to the faucet or a separate piece included with the Capacity Monitor 1 Do not use scissors 2 Fully insert the tubing into the adapter on the OUTLET port of the system housing the tubing should typically be inserted 5 8 into the adapter NOTE When pushing the tubing into the adapter you will encounter some resistance This does not mean that the tube is fully inserted Continue to push firmly until the tubing is inserted as far as possible roughly 5 8 into the adapter Insert tubing and push until Insert blue tubing 5 8 feel resistance at this point the tubing is not fully inserted 3 Pull on the tubing to make sure that it is securely connected Push firmly until the tubing is inserted as far as it will go Connect the Tubing to the Inlet Port 1 Using wire cutters or a knife cut square cut the tip end off of the clear plastic tubing con nected to the Adapta Valve Do not use scissors Do not cut more than 1 2 off of the adapter clear tubing end of the clear plastic tubing 9 INLET 2 Fully insert the tubing into the adapter on the INLET
5. Please visit our website for list of product certifications NOTES Multipure Drinking Water Systems have been certified as indicated by NSF International for compliance to NSF ANSI Standard Nos 42 amp 53 The Multipure Drinking Water Systems have been certified by the State of California Department of Public Health for the reduction of specific contaminants listed herein Chloroform was used as a surrogate for claims of reduction of VOCs Multipure Systems tested at gt 99 8 actual reduction of Chloroform Percent reduction shown herein reflects the allowable claims for VOCs as per tables in the Standard Do not use with water that is microbiologically unsafe or of unknown quality without adequate disinfection before or after the system Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts Filter life will vary in proportion to the amount of water used and the level of impurities in the water being processed For optimum performance it is essential that the filter be replaced on a regularly scheduled basis as follows a annually b when the unit s rated capacity has been reached c the flow rate diminishes or d the filter becomes saturated with bad tastes and odors Multipure Drinking Water System Housings are warranted for a lifetime provided that filter has been changed at least once per year All exterior hoses and attachments to the System are warranted for one year Please see th
6. 1295 Date Issued June 23 2012 Trademark Model Designation Multi Pure MP1200EL Replacement Elements pg Manufacturer Multipure International The water treatment device s listed on this certificate have met the testing requirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminants Microbiological Contaminants Inorganic Radiological Contaminants Cysts protozoan Asbestos Turbidity Lead Mercury Organic Contaminants Radon Se VOCs by Surrogate PCBs Alachlor Endrin Simazine Atrazine Ethylbenzene Styrene Benzene EDB 1 1 2 2 Tetrachloroethane MTBE Carbofuran Haloacetonitriles HAN Tetrachloroethylene Carbon Tetrachloride Bromochloroacetonitrile Toluene VOCs Chlorobenzene Dibromoacetonitrile 2 4 5 TP Silvex Chloropicrin Dichloroacetonitrile Tribromoacetic Acid 2 4 D Trichloroacetonitrile 1 2 4 Trichlorobenzene DBCP Haloketones HK 1 1 1 Trichloroethane o Dichlorobenzene 1 1 Dichloro 2 Propanone 1 1 2 Trichloroethane p Dichlorobenzene 1 1 1 Trichloro 2 Propanone Trichloroethylene 1 2 Dichloroethane Heptachlor Trihalomethanes THMs 1 1 Dichloroethylene Heptachlor Epoxide Bromodichloromethane cis 1 2 Dichloroethylene Hexachlorobutadiene Bromoform trans 1 2 Dichloroethylene Hexachlorocyclopentadiene Chloroform 1 2 Dichloropropane Lindane Chlorodibromomethane cis 1 3 Dichloropropylene Methoxychlor Xylenes Dinoseb Pentachlorophenol Toxaphene Rated Se
7. 16 3 5 Placing the System Under the Sink 17 3 6 Installing the System for Inline Use 17 3 7 Preparing and Operating Your Drinking Water System 18 4 Maintenance 4 1 Regarding Filter Capacity 19 4 2 Removing the Old Filter 19 4 3 Installing the New Filter 19 4 4 Resetting the Capacity Monitor or Changing the Batteries 20 4 5 Flushing Disinfecting the System 20 5 Additional Information 5 1 Warranty 20 5 2 Performance Certifications 21 5 3 Performance Data Sheet 22 24 5 4 California Certification 25 5 5 Troubleshooting 26 5 6 Frequently Asked Questions 27 About the Aquaversa Drinking Water System The Multipure Aquaversa Drinking Water System Model MP750 is designed for use on the countertop next to the sink below the sink or inline with other devices It can connect to the existing faucet or to the water source below the sink Aquaversa includes all the accessories and fittings required for installation except for the MP750SI Inline unit If installation or operation assistance is required please contact your Multipure Independent Distributor If the Independent Distributor is unavailable please contact Multipure Customer Service at 800 622 9206 Before You Begin Multipure Drinking Water Systems DWS have been extensively tested and certified by NSF International to provide the highest level of assurance that the device will perform as claimed Please read this manual before proceeding with the installation a
8. 20 5 2 Performance Certifications Multipure Drinking Water Systems Product Performance Tested and Certified Multipure Drinking Water Systems have been tested and certified by NSF International to comply with NSF ANSI Standards 42 and 53 for the reduction of specific contaminants being considered as established or potential health hazards Standard 42 Aesthetic Effects System tested and certified by NSF International against NSF ANSI Standard 42 for the reduction of NSF ANSI Standard 53 for the reduction of Chloramine Asbestos Chlordane Chlorine taste and odor Cyst Lead Nominal Particulate reduction class Mercury MTBE PCB Toxaphene Turbidity Radon VOC listed below Standard 53 Health Effects System tested and certified by NSF International against Volatile Organic Chemicals VOC includes Disinfection By Products chloropicrin haloacetonitriles HAN bromochloroacetonitrile dibromoacetonitrile dichloroacetonitrile trichloroacetonitrile haloketones Hk 1 1 dichloro 2 Propanone 1 1 trichloro 2 Propanone trinalomethanes THMs TTHMs bromodichloromethane bromoform chloroform dibromochloromethane tribromoacetic acid Chemicals benzene carbon tetrachloride chlorobenzene 1 2 dichloroethane 1 1 dichloroethylene cis 1 2 dichloroethylene 1 2 dichloropropane cis 1 3 dichloropropylene ethylbenzene hexachlorobutadiene hexachlorocyclopentadiene simazine styrene 1 1 2 2 tetrachloroethane tetrachloroethylene t
9. bracket is in an upright position when the two holes on the bracket are at the top 2 Attach the system to the bracket a ilt the system toward the wall b Slide the V Band that runs along the center circumference of the system up and into the upper notch on the bracket c Straighten the system upright and let the vane bottom of the V Band settle into the lower notch on the bracket 3 To remove the system for servicing reverse bracket the previous steps bracket MP750SB The MP750SB MP750SI and MP1200EL units can also be placed upside down in the acrylic sleeve A notch has been cut out of the sleeve to accommodate the tubing In this configuration it may be necessary to relieve air which builds up in the stainless steel housing every two months To relieve the built up air 1 Turn on the faucet connected to drinking water system 2 With the faucet in the on position and water flowing through it pick up the stainless steel housing and turn it right side up so that the ports and tubing are now on top You ll hear a whooshing sound come from the faucet as the trapped air escapes through the open faucet This should only take a few moments 3 water continues to flow out of the faucet return the housing back to its upside down position and turn off the faucet 3 6 Installing the System for Inline Use Multipure inline systems are ideal for refrigerators water coole
10. flow for approximately 30 minutes This will flush the filter and charge the carbon Turn off the DWS faucet 10 Check all connections to make sure that there are no leaks 11 Congratulations Your DWS is now ready for use If you have any questions regarding the installation of your Multipure Drinking Water System call Multipure International Customer Service Department 7251 Cathedral Rock Drive Las Vegas NV 89128 702 360 8880 phone 800 622 9206 toll free 702 360 8575 fax email custsvc multipure com www multipure com 18 4 4 1 4 1 2 Disengage the water supply to the DWS by turning the Adapta Valve shutoff valve 8 9 10 Rinse out the inside of the system housing hand washing if necessary 11 Inspect the black rubber cushion on the inside of the top half of the housing making sure 4 1 2 Turn on the DWS faucet to relieve the water pressure in the system If the system is mounted on a bracket remove the system from the bracket With the DWS housing in an upright position unscrew the black knob on the Locking With the black knob removed spread the Locking V Band apart and let it drop off the Lift the top half of the DWS off of the bottom half Make sure that the black O ring 3 Installing the New Filter If you have not done so already remove the plastic wrapper and instruction wrap Align the threaded hole of the new filter cartridge onto the inside thread of the
11. normal care and will repair or replace any system at no charge excluding trans portation to Multipure Corporate Headquarters to the customer during the warranty period The DWS housing is warranted for a lifetime provided the filter has been changed at least once per year all exterior hoses and attachments to the DWS are also warranted for defects in material and workmanship for one 1 year Multipure Solid Carbon Block Filters are warranted for defects in material and workmanship for use under normal care The capacity of the filter cartridge depends upon the amount of impurities in the water to be processed Except as otherwise expressly provided above Multipure makes no warranties express or implied arising by law or other wise including without limitation the implied warranties of merchantability and fitness for a particular purpose to any per son This limited warranted may not be altered varied or extended except by a written instrument executed by Multipure The remedy of repair or replacement as provided under this limited warranty is exclusive In no event shall Multipure be liable for any consequential or incidental damages to any person whether occasioned by negligence of the manufacturer including without limitation damages of loss of use cost of substitution property damage or other monetary loss Warranty is valid only if the DWS is operated within conditions listed herein The warranty begins from the date of purchase
12. one 1 second each and then blink green five 5 times twice The remaining capacity and time is now reset to the original capacity Changing the Batteries 1 Open the top of the Filter Monitor Unit and remove and discard the used batteries 2 Insert two 2 fresh AAA batteries into the battery compartment making sure to match the and signs Close the battery compartment 3 There will be a long audio sound and the LED will blink green for two seconds and then blink green five times 4 After installing the batteries press the check reset button to confirm the LED is functioning 4 5 Flushing Disinfecting the System Multipure recommends that you not allow water to sit in the system for extended periods of time without use If a unit is left unused for more than 10 days it may need to be flushed disinfected before resuming normal use 1 Remove the filter by following the directions in 4 2 Removing the Old Filter 2 Add 5 to 7 drops of bleach to the bottom half of the system 3 Reconnect the top half of the housing without a replacement filter installed 4 Turn on the water supply and allow the system to fill up with the water bleach solution a Countertop Systems i Turn on the faucet and press the right button on the diverter valve to select the filtered water spout ii Once water begins to flow press the left button to stop the filtered water spout iii Turn off the faucet and let the system soak for at least 30 mi
13. port of the system housing the tubing should typically be inserted 5 8 into the adapter NOTE When pushing the tubing into the adapter you will encounter some resistance This does not mean that the tube is fully inserted Continue to push firmly until the tubing is inserted as far as possible roughly 5 8 into the adapter 3 Pull on the tubing to make sure that it is securely connected Connecting to Straight Adapter Insert tubing and push until you feel resistance at this point the tubing is not fully inserted Push firmly until the tubing is inserted as far as it will go 15 Connecting to an Icemaker Instant Hot D Use the following steps to connect the DWS to an icemak er instant hot dispenser or other device in addition to your faucet or capacity monitor faucet A TEE adapter MC445 is required NOTE To connect your DWS to the icemaker instant hot dispenser other device you must have access to this other device from your sink ispenser or Other Device Ga Blue tubing 1 Using wire cutters or a knife cut square cut the blue Tee MC445 plastic tubing 6 from where it is connected to the 74 purchased separately OUTLET port of the DWS housing Do not use S Clear tubing MC232RH 5 1550 5 0 purchased separately Connect to refrigerator 5 orother device 2 Fully insert the blue plastic tubing from the DWS OUTLET into the bot
14. roughly 5 8 into the fitting tubing is not fully inserted Push firmly until the tubing is sa Insert blue tubing 5 8 inserted as far as it will go Set up the Filter Monitor Unit 1 Connect the black wire 8 from the LED Display Plate into the Filter Monitor T apter Unit 14 2 Open the top of the FMU and insert two 2 AAA batteries not included into the OUTLET battery compartment making sure to match the and signs Close the battery compartment 3 There will be a long audio sound and the LED will blink green for two seconds and then blink green five times 4 After installing the batteries press the check reset button to confirm the LED is functioning 5 Press and hold the check reset button on the Filter Monitor Unit FMU for three 3 seconds You should hear a long audible sound 6 The LED on the LED Display Plate will blink green for one 1 second with an audible sound then blink green and red for one 1 second each and then blink green five 5 times twice The remaining capacity and time is now reset to the original capacity 7 Peel off the paper backing from the hook and loop connector strip and attach one piece to the back of the FMU Peel off the paper backing from the second hook and loop connector strip and attach it to the desired wall location Attach the FMU to the wall using the two hook and loop connector strips 12 3 2 c Installing the Capacity Monitor Faucet contin
15. top Reconnect the top half of the housing with attached filter cartridge with the bottom Screw the black knob onto the Locking V Band turning it clockwise to tighten Maintenance 1 Regarding Filter Capacity Exact filter capacity varies in proportion to the amount of water used and the level of impurities in the water being processed For contaminants reduced through physiochemical adsorption the filter capacity is 750 gallons For contaminants reduced through mechanical filtration capacity claims are inapplicable due to broad variations in the quality and quantity of physical matter in the drinking water Excessive physical matter will cause the DWS to clog diminishing flow rate but reducing the contaminants from the resultant water stream For optimum performance and to maintain the lifetime warranty on your system housing it is essential that the filter be replaced when the first of the following occurs 1 annually 2 when the system reaches its rated capacity 3 when the flow rate diminishes or 4 when the filter becomes saturated with bad tastes and or odors 2 Removing the Old Filter Before opening the DWS housing place a pan or basin beneath the housing clockwise or by turning the water supply shutoff valve clockwise a Tilt the top of the system toward the wall b Slide the locking V Band up and into the upper bracket notch c Slide the system out of the bracket V Band by turning it counter clockwise
16. 3 8 configuration Ny T L 3 8 slip joint nu 11 angle stop valve c3 TE The acrylic sleeve Item 12 is an optional part available for purchase 4 Countertop Installation Overview amp Part Numbers Model MP750SC hi Diverter Valve Diverter b Valve irm Part Numbers MC6400ASBL Hose and Diverter Valve MCL500 Housing Top MC252 BLK Black Rubber Cushion inside housing top MC253ASBL Locking V Band CB6 Filter Cartridge MC351 O Ring MCB500 MP750 Housing Bottom 011 25 4100 Acrylic base MC700 Standard Adapters see page 7 MM MM e 1 INSTALLATION PREPARATION Before beginning inspect your DWS to confirm that it has been received in good condition and that all parts are included refer to the specific installation section for the parts list Perform the following instructions prior to system installation Should you require assistance please contact your Independent Distributor if she he is not able to help you please feel free to con tact Multipure s Customer Service Department directly at 800 622 9206 Model MP750SB 1 1 Installing the Filter Cartridge If you have not done so already remove the plastic wrapper and instruction wrap from around the filter With the DWS housing in an upright position unscrew the black knob on the Locking V Band by turning it counter clockwise With the black knob removed spread the Locking V Band apart and lift up and off of top the DWS Ca
17. ETHANES 7 THM Chloroform Bramoform is TURBIDITY 2057 11 1 NTU 0 5 NTU Unswyrm Trichlarabenzene see 1 2 4 TRICHLOROBENZEMNE gt 09 0 160 0 0005 Vinylbenzene see STYRENE 99 0 0005 XYLENES gt 9 0 001 23 5 3 Performance Data Sheet continued NSF ANSI 42 Aesthetic Effects The System has been tested according to NSF ANSI Standard 42 for the reduction of the following substances The con centration of the indicated substances in water entering the system was reduced to a concentration less than or equal to the permissible limit for water leaving the system Maximum permissible Influent challenge product water Percent concentration concentration Substance Reduction mg L unless specified mg L unless specified CHLORAMINE as Aesthetic Effect As 297 30 mgiL 10 0 5 mgiL Monachloraminae CHLORINE as Aesthetic Effect g4 2 0 Mail 10 or 50 PARTICULATE Mominal Particulate Reduction Class l Particles 0 5 TO 1 UM Class 99 At Least 10 000 particles mL 855 Note This addresses the U S Environmental Protection Agency EPA Primary and Secondary Drinking Water Regulations in effect at its time of publica tion as they relate to Multipure s performance in conformance to the industry performance criteria These regulations are continually being updated at the Federal level Accordingly this list of MCLs will be reviewed and amended when appropriate
18. Multipure MULTIPURE Multipure Drinking Water Systems Aquaversa OwNER S MANUAL For Model Nos MP750SC MP750SB MP750SI and MP1200EL Please retain this manual for future reference Multipure International e P O Box 34630 e Las Vegas NV 89133 4630 e Phone 702 360 8880 e Toll Free 800 622 9206 www multipure com Multipure Drinking Water Systems Thank you for selecting a Multipure Drinking Water System to meet your need for quality drinking water You have acquired one of the finest drinking water treatment devices available for the reduction of a wide array of contaminants We are confident that your Multipure System will make a difference in your life Thank you for your business Table of Contents About 3 Before You Begin 3 Specifications 3 Below Sink Installation Overview and Part Numbers 4 Countertop Installation Overview and Part Numbers 5 1 Installation Preparation 1 1 Installing the Filter Cartridge Universal 6 1 2 Locating the Approriate Installation Instructions 7 2 Countertop Installation 2 1 Connecting the Hose and Diverter Valve to the Faucet T 2 2 Preparing and Operating Your Drinking Water System 8 3 Below Sink Installation 3 1 Required Installation Tools 8 3 2 Installing the Faucet 9 3 2 a Drilling the Faucet Hole 9 3 2 b Installing the Standard Faucet 10 3 2 c Installing the Capacity Monitor Faucet 11 13 3 3 Connecting to Your Plumbing 13 14 3 4 Connecting the Tubing to the Housing 15
19. ack washer 11 upward over the blue tubing 5 and faucet stud 4 c Slide the lock washer 12 upward over the faucet stud below the black plastic washer d Screw on the stud wing nut 13 below the lock washer e Hand tighten the wing nut to secure the faucet Capacity Monitor Assembly 11 3 2 c Installing the Capacity Monitor Faucet continued Connect the Tubing to the Filter Monitor Unit Capacity Monitor Assembly NOTE Complete this step only after the DWS tubing has been connected in section 3 4 Connect the Tubing to the Housing 1 Connect the two tube fittings 15 MC744 to the Filter Monitor Unit 14 FMU by threading them into the threaded ports one on each side tighten securely but do not over tighten 2 The FMU can be mounted either horizontally or vertically but vertical installation is recommended NOTE The FMU will function with water flow in either direction 3 Fully insert the blue plastic tubing 5 from the DWS OUTLET into one INLET side of the FMU to faucet from housing 4 Fully insert the blue plastic tubing 5 from the faucet into the other Pull to check that the side of the FMU tubing is secure Insert tubing and push until you feel resistance at this point the NOTE When pushing the tubing into the fitting you will encounter some resistance This does not mean that the tube is fully inserted Continue to push firmly until the tubing is inserted as far as possible
20. ard Faucet Complete Faucet Assembly with Blue Tubing MC652 j Hwa THU RED ul I Jl IP Niji AAAA Wi if 1 jJ M ull lil Blue Tubing NOTE The blue plastic tubing is attached to the faucet 1 From the sink countertop a Place the larger soft black rubber washer over the faucet hole b Place the cover plate on top of the large washer Place the smaller soft black rubber washer top of the cover plate d Place the faucet base over the smaller soft black rubber washer and atop the cover plate 2 From under the sink a Slide the hard plastic black washer with the smaller side up upward over the blue tubing Slide the lock washer upward below the hard plastic washer b Slide the wing nut upward below the lock washer d Hand tighten the wing nut to secure the faucet 3 2 c Installing the Capacity Monitor Faucet When the Aquaversa is installed with a capacity monitor the DigiFlow 5000V Capacity Monitor MC993 flashes red when the filter should be changed Two AAA batteries not included are required for capacity monitor operation The Capacity Monitor consists of two main parts the LED Display Plate that sits below the faucet and the Filter Monitor Unit FMU that connects in line between the drinking water system housing and the faucet Faucets with Ca
21. ce with any state or local laws and regulations before use Specifications Approximate Filter Capacity Approximate Filter Capacity with Capacity Monitor Replacement Filter Type Approximate Flow Rate psi 0 75 gpm Operating Temperature Range 32 F 0 Cito 100 F 38 C for cold water use only Particle Retention Size Below Sink Installation Overview amp Part Numbers Item Part Part Description Item Part Part Description MC652 Faucet assembly with blue tubing 8 MC253ASBL V band with knob attached 9 MC126 Bracket MC780 Wing nut 10 MC351 O ring MC720 Outlet adapter connects to blue 11 MCB500 Housing bottom tubing attached to faucet 12 011 25 4100 Acrylic sleeve MC720 Inlet adapter connects to clear 13 MC232RH Clear tubing connects inlet adapter to tubing plumbing MCL500 Housing top MC920LF Adapta Val MC252 BLK Black Rubber Cushion inside housing top CB6 Carbon Block Filter Connect clear tubing to plumbing Option A or B Note the Aquaversa MP750SI Inline unit does not include the following parts faucet assembly 1 wing nut 2 outlet adapter 3 inlet adapter 4 acrylic sleeve 12 clear tubing 13 adapta valve 14 tubing J from faucet d Ey A B Water supply line with Adapta Valve in 1 2 configuration Adapta Valve 1 2 configuration 1 2 slip joint nut 7 1 riser gt 1 2 slip joint nut 3 Adapta Valve
22. e Owner s Manual for complete product guarantee and warranty information Please see the Owner s Manual for installation instructions and operating procedures In compliance with New York law it is recommended that before purchasing a water treatment system NY residents have their water supply tested to determine their actual water treatment needs Please compare the capabilities of the Multipure unit with your actual water treatment needs While testing was performed under standard laboratory conditions actual performance may vary 10 The list of substances which the treatment device reduces does not necessarily mean that these substances are present in your tap water 24 5 4 California Certification Department of Public Health State of California Department of Public Health Water Treatment Device Certificate Number 97 1294 Date Issued June 23 2012 Trademark Model Designation MP750SB MP750SC MP750SI MPCT Replacement Elements Manufacturer Multipure International The water treatment device s listed on this certificate have met the testing r quirements pursuant to Section 116830 of the Health and Safety Code for the following health related contaminants Microbiological Contaminants Inorganic Radiological Contaminants Cysts protozoan Asbestos Turbidity Lead Mercury Organic Contaminants Radon ne VOEs by Surrogate PCBs Alachlor Endrin Simazine Atrazine Ethylbenzene Styrene Toxap h
23. e the filter Minerals in the water can build up on the diverter valve causing the bypass lever ta stick and preventing the buttons fram being pressed easily A sticking bypass lever can be solved by lubricating it or by dissolving the mineral deposits Lubrication requires vegetable oil because lubrication does not dissolve the mineral deposits it may need ta be performed periodically 1 Unscrew the diverter valve and remove trom the faucet 2 Pour a small amount of vegetable oil in the inlet hole 3 Push the left and right buttons on the diverter valve several times to lubricate it thoroughly Reconnect the diverter valve to the faucet Dissolving requires vinegar may cause discoloration to the metal 1 Unscrew the diverter valve and remove from the faucet Soak the diverter valve in a bowl of vinegar for 10 minutes Rinse the diverter valve and reconnect to the faucet The bypass lever can occasionally become stuck due to the presence of air in the tubing This can prevent the buttons from being pressed 1 Unscrew the diverter valve and remove trom the faucet 2 Press the left and right buttons to test it If they press in easily then removing the diverter valve freed the air in the tubing 3 Reconnect the diverter valve to the faucet 5 6 Frequently Asked Questions o Question Ss a soU intuens Ma Mineral components can determine the pH of water and minerals dissolved in solution in the wate
24. e until tight DO OVERTIGHTEN c Make sure that the supply line does not block the shutoff valve on the side of the Adapta Valve If necessary trim the supply line before reconnecting 5 Connect the 1 4 clear plastic tubing included with the system to the Adapta Valve a Using wire cutters or a knife cut Square cut the tip end off of the clear plastic tubing Do not use scissors b Insert the tubing fully into the opening of the shutoff valve on the side of the Adapta Valve the tubing should typically be inserted 5 8 into the adapter Sa Insert clear tubing 5 8 NOTE When pushing the tubing into the opening you will encounter some resistance This does not mean that the tube is fully inserted Continue to push firmly until the tubing is inserted as far as possible roughly 5 8 into the adapter Push the tubing into the small hole as far as it will go Pull to check secure 6 Confirm that the Unit Shutoff Valve attached to the Adapta Valve is in the OFF position by rotating the handle clockwise until it stops 7 Proceed to section 3 4 Connecting the Tubing to the Housing to connect the clear plastic tubing to the DWS 14 3 4 Connecting the Tubing to the Housing Attach the Adapters to the Housing OUTLET a NLET 1 Connect the included Inlet adapter MC720 to the system housing s labeled Inlet port Rotate the adapter clockwise first by hand then using a wrench to tighten onto the system 2
25. ed Installation Tools The following tools are required to install your Aquaversa for below sink use 1 Installing the faucet on a ceramic porcelain sink 3 8 reversible electric drill 7 16 or 1 2 high speed steel drill bit 1 2 carbide tipped masonry drill bit hammer center punch 8 adjustable wrench pliers locking pliers 2 Installing the faucet stainless steel sink a everything from list 1 plus 1 8 high speed drill bit 3 Installing the Adapta Valve a adjustable wrench b wire cutter or knife Model MP750SB 3 2 Installing the Faucet The Aquaversa faucet can be installed through a standard faucet hole or spray hose hole in your sink if one is available If no hole is available refer to section 3 2 a Drilling the Faucet Hole Note that there are separate sections for installing a faucet with or without a capacity monitor Proceed to the instructions for your installation type 1 For a standard faucet proceed to section 3 2 b Installing the Standard Faucet 2 For a capacity monitored faucet proceed to section 3 2 c Installing the Capacity Monitor Faucet 3 2 a Drilling the Faucet Hole 1 Select and mark the faucet mounting spot on the sink a Confirm that there are no reinforcing ribs under the desired faucet location b If you have an extra hole in your sink for a spray hose you may also choose to disconnect the spray hose and use that existing hole for t
26. ene Benzene EDB 1 1 2 2 Tetrachloroethane MTBE Carbofuran Haloacetonitriles HAN Tetrachloroethylene Carbon Tetrachloride Bromochloroacetonitrile Toluene VOCs Chlorobenzene Dibromoacetonitrile 2 4 5 Silvex Chloropicrin Dichloroacetonitrile Tribromoacetic Acid 2 4 D Trichloroacetonitrile 1 2 4 Trichlorobenzene DBCP Haloketones HK 1 1 1 Trichloroethane o Dichlorobenzene 1 1 Dichloro 2 Propanone 1 1 2 Trichloroethane p Dichlorobenzene 1 1 1 Trichloro 2 Propanone Trichloroethylene 1 2 Dichloroethane Heptachlor Trihalomethanes THMs 1 1 Dichloroethylene Heptachlor Epoxide Bromodichloromethane cis 1 2 Dichloroethylene Hexachlorobutadiene Bromoform trans 1 2 Dichloroethylene Hexachlorocyclopentadiene Chloroform 1 2 Dichloropropane Lindane Chlorodibromomethane cis 1 3 Dichloropropylene Methoxychlor Xylenes Dinoseb Pentachlorophenol Rated Service Capacity 750 gallons Rated Service Flow 0 75 gpm Do not use where water is microbiologically unsafe or with water of unknown quality except that systems claiming cyst reduction may be used on water containing cysts Do not use on water sources with a radon activity greater than 4000 pCi L and follow the manufacturer s recommended replacement schedule for the carbon filter to a maximum of one year System treats radon from drinking water only and does not reduce radon from indoor air State of California Department of Public Health Water Treatment Device Certificate Number 97
27. he DWS faucet 2 Use the hammer to gently tap the center punch on the sink location where the hole is to be drilled This creates an indentation marking the location to drill If You Have a Porcelain Ceramic or Cast Acrylic Sink CAUTION Porcelain ceramic and cast acrylic surface materials are extremely hard and can crack or chip quite easily Use extreme caution when drilling Multipure is not responsible for any damages resulting from faucet installation NOTE If you are installing a capacity monitor you MUST use the 1 2 high speed steel drill bit for step 2 1 Use the 1 2 carbide tipped masonry drill bit to grind away the porcelain down to the metal clearing away enough porcelain to allow drilling without damaging the porcelain surface Carefully grind away porcelain 2 Carefully use the 7 16 or 1 2 high speed steel drill bit to completely drill a hole through the metal sink CAUTION Do not allow the drill bit to grab the porcelain as this will damage the surface If You Have a Stainless Steel or Metal Sink NOTE If you are installing a capacity monitor you MUST use the 1 2 high speed steel drill bit for step 2 1 Use the 1 8 high speed drill bit to drill a pilot hole 2 Use the 7 16 or 1 2 high speed steel drill bit to completely drill a hole through the metal sink Note For drilling a hole in your countertop please consult with the countertop manufacturer 3 2 b Installing the Stand
28. hoose one with adapter Many installations do not require an adapter T 2 2 Preparing and Operating Your Drinking Water System bypass lever Using a paper towel or cloth dry off all connections and the DWS housing 2 Make sure that all connections are tightly secured 3 Purge any air from the unit a Press the right button on the diverter valve to select the filtered water spout The water will flow through the DWS and emerge from the smaller opening on the diverter valve b Allow water to flow through the DWS and filtered water spout for five minutes c Press the left button to select the unfiltered water spout and then turn off the faucet 4 Make sure that all connections are tightly secured and that there are no leaks 5 Turn on the faucet and press the right button to select the filtered water spout 6 Allow water to flow through the DWS and filtered water spout for approximately 30 minutes This will flush the filter prior to use 7 Press the left button to select the unfiltered water spout 8 Turn off the faucet 9 Check all connections to make sure that there are no leaks 10 The system is now ready for use 3 Below Sink Installation The Aquaversa models MP750SB and MP1200EL are designed for use below the sink and can be installed on the incom ing cold water line The MP750SB and MP1200EL systems are connected to a specially designed faucet which installs directly on the sink 3 1 Requir
29. igned to fit larger faucets and MC1068 is designed to fit smaller faucets c lf Your Faucet Requires More Room for the Diverter Valve Connection Some faucets particularly sprayer hose faucets require additional room for the diverter valve connection If this applies attach the long adapter part MC257 to the opening of the faucet spout sprayer and then attach the diverter valve to the adapter The DWS may need to be repositioned on the sink to allow enough room for sprayer faucet use d If the Adapters Do Not Fit Your Faucet Although the adapters included with your DWS allow connections with many standard faucets they do not cover every type of available faucet connection If none of the adapters allow the diverter valve to connect to your faucet please contact Multipure Customer Service at 1 800 622 9206 ext 175 to request part MC 105 part MC109 or part MC719 as possible adapter solutions When connected properly the hose from the diverter valve should lead toward the back of the faucet and sink The diverter valve features a bypass lever with a button on the left and right sides of the diverter valve Press the left button to bypass the DWS and select the unfiltered water spout larger opening Turn on your faucet to let unfiltered water flow out of the diverter valve and to make sure that the diverter valve is properly connected Turn off the faucet Diverter Valve Attachment Diverter Valve Attachment MC700 Adapters c
30. ires fixtures different from those included with your shipment please contact Multipure s Customer Service office at 800 622 9206 ext 175 Determine Your Adapta Valve Configuration If your residence has a cold water supply line with a 3 8 or 1 2 slip joint connection you may use the Adapta Valve includ ed with your system to connect your DWS to the plumbing The Adapta Valve assembly MC922ASBL includes both the valve and threading adapter Adapta Valve 14 a I erae ai NOTE When attaching the Adapta Valve to straight pipe threads use Teflon tape on the threads Wrap the tape around the pipe only once Adapta Valve 1 2 configuration T w A ain Adapta Valve 3 8 configuration 3 8 slip joint nut 7a e TI Em angle stop valve c3 i i 2 1 angle stop valve Water supply line A Water supply line with B Water supply line with before installation Adapta Valve in 3 8 configuration Adapta Valve in 1 2 configuration 13 Adapta Valve Installation continued 1 Using the 3 8 configuration a The 3 8 configuration is used on a water supply line with a 3 8 slip joint b The 3 8 configuration is typically installed at the bottom of the riser at the angle stop valve 2 Using the 1 2 configuration a The 1 2 configuration can be used at either the top of the riser at the faucet pipe or at the bot
31. loropropane y 1 2 DCA see 1 2 DICHLOROGETHAME 1 1 DCE see 1 1 DICHLORGETHYLENE DIBROMOCHLOROMETHANE T THM Chlaradibromametharnae DIBROMOCHLOROPROPAMHE D BCP DICHLOROBEHZENHE 1 7 Dichlarabenzene p DICHLOROBEHZEHE para Dichlarabenzene 1 2 DICHLOROETHAHE 1 2 D C A 1 1 1 D CE CIS 1 2 DICHLOROETHYLEHE TRANS 1 2 DICHLOROETH YTLEHE 1 2 DICHLOROPROPAMHE Propylene Dicehlaride CIS 1 3 DICHLOROPROPYLENE DIHOSEB EDB see ETHYLENE DIBROMIDE ENDRIN Entamoeba see CYSTS ETHYLBENZENE ETHYLENE DIBROMIDE EDB Furadan see CARBOFURAN Percent Reduction 2085 gt 99 9 Hn 44 244 0 244 0 44 99 gt 99 5 gt 99 99 244 0 99 95 99 95 99 gt 99 95 gt 99 244 0 24095 28855 20855 45 44 g 44 28855 49 g9 gt 49 g9 99 95 44 49 44 Influent challenge concentration mg L unless specified 0 05 10 to 10 fibersiL fibers greater than 10 micrometers in length 0 1 0 081 0 300 0 30 0 300 0 30 0 19 0 078 0 04 1096 0 015 0 300 0 30 minimum 50 minimum 0 110 0 052 0 058 0 093 0 300 0 30 0 052 0 08 0 04 0 099 0 083 0 17 0 086 0 08 0 079 0 17 0 044 0 053 minimum 0 088 0 044 0 19 Maximum permissible product water concentration mg L unless specified 0 001 99 reduction requireme
32. nd use of your system Installation operation and maintenance requirements are essential to the performance of your system failure to follow any instructions or operating parameters contained herein may lead to product damage or product failure Replacement filters can be purchased directly from Multipure For the latest prices please visit our website at http www multipure com store Actual filter life depends on the amount of water used and the level of impurities in the water See 4 1 Regarding Filter Capacity for additional details Multipure Drinking Water Systems are not intended for use with microbiologically unsafe water or non municipally treated water Systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts See 5 5 Frequently Asked Questions for additional details Do not allow water to freeze in the system If the system is exposed to freezing temperatures drain water from the system and remove the filter Allow the filter to thaw before replacing and reusing Do not allow water to sit in the system for extended periods of time i e 10 days or more without use See 4 5 Flushing Disinfecting the System for additional details To dispose of the used filter remove it from the housing and place in normal refuse Filters disposed in a normal landfill will not release any chemical contaminants and may continue to adsorb additional contaminants in the landfill Check for complian
33. nt 0 003 0 001 0 015 0 015 0 001 0 0018 0 002 0 001 0 0002 0 015 99 95 99 95 0 0017 0 00002 0 0049 0 001 0 015 0 00002 0 001 0 001 0 0049 0 001 0 0005 0 001 0 001 0 001 0 0002 0 00002 0 00059 99 95 0 001 0 00002 0 001 Percent reduction reflects actual performance of Multipure product as specifically tested at 200 of capacity 1500 gallons Percent reduction shown for VOCs reflects the allowable claims for Volatile Organic Chemicals Compounds as per Tables Chloroform was used as a surrogate for VOC reduction claims the Multipure Systems actual reduction rate of Chloroform was gt 99 8 as tested at 200 of capacity 22 5 3 Performance Data Sheet continued Maximum permissible product water concentration Influent challenge concentration Substance Percent Reduction mg L unless specified mg L unless specified Giardia Lamblia see CYST gt 99 45 minimum 50 000 mL 99 95 HALOACETONITRILES HAN BROMOCHLOROACETONITRILE gawi 0 022 0 0005 DIBROMOACETONITRILE garo 0 024 0 0006 DICHLOROACETONITRILE gari 0 0096 0 0002 TRICHLOROACETONITRILE gawo 0 015 0 0003 HALOKETONES 1 1 DICHLORO 2 PROPANONE ggi 0 0072 0 0001 1 1 1 TRICHLORO 2 PROPANONE HB 0 00892 0 0005 HEP TACHLOR 9 0 25 0 00001 HEPTACHLOR EPOXIDE garo 0 0107 0 000 HEXACHLOROBUTADIENE Ferchlarahutadiene 9896 0 044 0 001 HEXACHLOROCYCLOPENTADIENE 099 0 060 0 000002 LEAD pH 6 5 gt 99 3
34. nutes b Below sink Systems i Remove the faucet spout and place it in a container with one quart of water and bleach 5 drops of bleach per one quart of water ii Allow the system and the faucet to soak for at least 30 minutes ii Clean the inside of the faucet spout with pipe cleaners You may also use a mild detergent such as Soft Scrub o Flush and rinse the system a Countertop Systems i With the faucet off press the right button on the diverter valve to select the filtered water spout ii Let the water and bleach flush out of the system until the water flow stops iii Open clean and rinse out the inside of the system housing iv Follow the directions in 1 1 Installing the Filter Cartridge Universal v Follow the directions in 2 2 Preparing and Operating Your Drinking Water System b Below sink Systems i Disassemble the system housing and pour out the water bleach solution Clean and rinse out the inside of the system housing ii Follow the directions in 4 3 Installing the New Filter 5 Additional Information 5 1 Warranty Multipure 90 Day Guarantee Multipure is confident in the performance of its Drinking Water Systems DWS If you should find this Drinking Water System unsatisfactory let us know within 90 days of purchase for a prompt exchange or refund Multipure Warranty Multipure warrants to the original retail customer its DWS and components to be free of defects in material and workmanship for use under
35. oluene trans 1 2 dichloroethylene 1 2 4 trichlorobenzene 1 1 1 trichloroethane 1 1 2 trichloroethane trichloroethylene xylenes total Herbicides alachlor atrazine 2 4 D dinoseb pentachlorophenol 2 4 5 TP silvex Pesticides carbofuran dibromochloropropane DBCP o dichlorobenzene p dichlorobenzene endrin ethylene dibromide EDB heptachlor heptachlor epoxide lindane methoxychlor Claims of capacity are not applicable to contaminants reduced by mechanical filtration because of broad vari ations in the quality and quantity of physical matter in your drinking water Filter Model CB6 21 5 3 Performance Data Sheet Performance Data Sheet below The concentration of the indicated substances in water entering the system was reduced to a con centration less than or equal to the permissible limit for water leaving the system as specified in NSF ANSI 53 Health Effects t Multipure Drinking Water Systems have been tested and certified under NSF ANSI Standard 53 as shown MULTIPURE For Model Nos MP750SC MP750SB MP750SI MP1200EL Substance AL ACHLOR ASBESTOS ATRAZIME BHEH ZEHE BROMODICHLOROMETHAMHE T THM BROMOFORM T THM CARBOFURAM Furadan CARBON TETRACHLORIDE CHLORDANE CHLOROBEHZEHE Monochlorobenzene CHLOROPICRIN CHLOROFORM TTHM surrogate chemical Cryptosporidium CYST CYST Giardia Cryptosporidium Entamoeba Toxoplasma 2 4 D DACP see Dibromoch
36. pacity Installation Overview Monitor include spout faucet handle faucet base faucet stud tubing blue attached to faucet smaller rubber washer LED display plate black wire attached to 7 tubing from larger rubber washer housing 10 black track washer 11 hard plastic black washer 12 lock washer 13 wing nut 14 filter monitor unit 15 two adapters MC744 Countertop black wire from capacity indicator plate tubing from faucet 2 Filter Monitor Unit NOTE In addition to the blue plastic tubing attached to the faucet A separate piece of blue tubing is included for connection between the housing OUTLET port and the Filter Monitor Unit 1 From the sink countertop a Place the LED Display Plate 7 over the faucet hole b Feed the attached black wire 8 down through the faucet hole Rotate the LED Display Plate so that the indicator light will be easy to see c Place the faucet base 3 on top of the LED Display Plate Feed the blue tubing and faucet stud down through the hole in the sink The faucet stud should now be accessible below the sink 2 From under the sink a Slide the black track washer 10 with the flat side down upward over the threaded faucet stud Guide the black wire 8 from the LED Display Plate through the track to protect the wire and prevent it from becoming pinched between the sink and the stud nut b Slide the hard plastic bl
37. r pass through the system unfiltered pH neutral Will low pH or acidic water affect the filter pH 7 alkaline pH 7 acidic Because Multipure filters da not treat the natural minerals dissolved in water the hardness softness of water has no effect the resultant filtered Multipure water Does deionized water or soft water have an effect on Multipure water The Aquaversa countertop cannot be connected ta an icemaker although Multipure below sink Drinking Water Systems Aquaversa Aquaperform can be connected to the sink refrigerator water dispenser or icemaker Can the Multipure system be connected to an icemaker Yes During an emergency or when the source water is off you can hand pump or siphon water through the Multipure system Can the Multipure system be used during an CAUTION The Multipure system is not intended for use where the water is emergency or when the water is turned off microbiologically unsafe or with water of unknown quality without adequate disinfection before ar after the unit To disinfect questionable source water add 1 4 tsp of household bleach per gallon of source water the Multipure system will remove this solution from the water during the filtering process Hand pump kits and emergency kits are available from Multipure Because the Agquaversa does not reduce any natural minerals present in water these minerals may solidify when the water is frozen and appear as
38. re 7251 Cathedral Rock Drive Las Vegas NV 89128 800 622 9206 toll free 702 360 8880 phone MULTIPURE 702 360 8575 fax headquarters multipure com Aquaversa Manual 1403
39. re not designed to treat drinking water for contaminants instead they are designed to adjust the hardness mineral content af the water What is the difference between a water softener and a Multipure Drinking Water System oof water is often desirable for bathing and laundering purposes and may extend the life of hot water heaters and boilers However soft water is not recommended far use on plants ar lawns Multipure recommends that you bypass a water softener when installing your Multipure Drinking Vater System Questionable water sources should be disinfected prior to use To disinfect questionable source water add 1 4 tsp of household bleach per gallon of source water the Multipure system will remove this solution from the water during the filtering process Can the Multipure Drinking Water System be used with untreated water _ Multipure systems are designed ta be used with municipally treated water they are not intended ta be used where the water is micrabialogically unsafe or with water of unknown quality without adequate disinfection before or after the unit systems certified for cyst reduction may be used on disinfected waters that may contain filterable cysts Be sure to replace your filter at least once a year or sooner if needed Date of Installation Unit Model Number Filter Type Dates of Filter Change To order a Replacement Filter Call 800 622 9208 Or www multipure com rf htm Multipu
40. refully set it aside Rubber Lift the top half of the DWS off of the bottom half Make sure that the black O ring remains place the bottom half of the housing Align the threaded hole of the filter cartridge onto the inside thread of the top half of the DWS Rotate the cartridge clockwise to tighten the cartridge typically requires four to five revolutions to tighten adequately Make sure that the cartridge is threaded properly and straight DO NOT OVERTIGHTEN Reconnect the top half of the DWS with attached filter cartridge with the bottom half Replace the Locking V Band making sure the screw is in place to connect the band together Screw the black knob onto the Locking V Band turning it clockwise to tighten Make sure that the Locking V Band is secured tightly and evenly around the top and bottom halves of the DWS housing 1 2 Locating the Appropriate Installation Instructions 2 Determine your installation type e g countertop below sink inline Proceed to the instructions for your installation type a For Countertop Installation proceed to section 2 Countertop Installation b For Below Sink Installation with or without a capacity monitor proceed to section 3 Below Sink Installation For Inline Installation proceed to section 3 6 Installing the System for Inline Use Countertop Installation When installing on a countertop the Aquaversa sits atop its included acrylic ba
41. rs or restaurants where all water to a cold water outlet or faucet is filtered The inline Aquaversa 7505 includes the housing filter bracket and screws The inline models are appropriate for an inline installation and can be used with your existing faucet Multipure recommends that a professional plumber install the system for inline use 7505 3 Preparing and Operating Your Drinking Water System 8 9 Using a paper towel or cloth dry off all connections and the DWS housing Make sure that all connections are tightly secured Turn the water supply back on rotate both the Adapta Valve shutoff valve and either the water supply Angle Stop Valve or water shutoff valve counter clockwise to engage the flow of water through the pipes Turn the handle on the DWS faucet to start the flow of filtered water Allow water to flow through the DWS and the faucet for five minutes This purges any air and loose carbon from the system Adjust the Angle Stop Valve or water shutoff valve so that the water flow to the drinking water faucet does not exceed the flow rate NOTE It takes approximately 20 seconds to fill a quart at 0 75 gallons per minute flow rate Turn off the DWS faucet and check for leaks a Check the V Band to confirm that it is secured evenly around the top and bottom housing halves b Hand tighten the black knob on the V Band until it is as tight as possible Turn on the DWS faucet and allow water to
42. rvice Capacity 1200 gallons Rated Service Flow 0 75 gpm Do not use where water is microbiologically unsafe or with water of unknown quality except that systems claiming cyst reduction may be used on water containing cysts not use on water sources with a radon activity greater than 4000 pCi L and follow the manufacturer s recommended replacement schedule for the carbon filter to a maximum of one year System treats radon from drinking water only and does not reduce radon from indoor air 25 5 5 Troubleshooting Odor rotten eggs no discoloration on the filter Odor rotten eggs with discoloration on the filter Color milky color in the water Color black color in the water Flow rate the water flow rate is slow Taste Odor miscellaneous Bypass lever sticking hard to move Bypass lever stuck cannot be pressed A rotten egg odor is a sign that HsS hydrogen sulfide qas is present in YoUr water source If hydrogen sulfide qas is present in your water source it is recommended that you rotate DWS usage between 2 filter cartridges When the DWS emits the rotten egg smell remove the filter and allow it to dry upside down to allow the gas to dissipate the filter can be reused once dry Use the second filter in the unit while the first filter is drying A rotten egg odor is a sign that HsS hydrogen sulfide is present in your water source Filter discoloration can determine the source
43. se on the counter next to the sink It connects to the existing faucet via a dual hose diverter valve Follow these instructions to connect the Aquaversa for countertop use 2 1 Connecting the Hose and Diverter Valve to the Faucet iF Remove the aerator or screen if present from the end of the faucet If facing the open end of the spout rotate the aerator counter clockwise to loosen and remove Attach the diverter valve directly to the faucet spout If the threads of the diverter valve do not match the threads of the faucet use one of the included faucet adapters to connect the diverter valve and faucet If facing the open end of the spout rotate the diverter valve and or adapter clockwise to tighten NOTE When using a faucet adapter the rubber washer in the adapter always faces up toward the faucet a lf Your Faucet Has an Outside Thread male connector For many faucets with an outside thread the diverter valve can attach directly to the faucet If the diverter valve is too small to attach to the faucet attach the inside thread female connector adapter part MC106 to the faucet and then attach the diverter valve to the adapter b If Your Faucet Has an Inside Thread female connector The diverter valve cannot directly connect to a faucet with a female connector Attach one of the outside thread male connector adapters part MC107 or part MC108 to the faucet and then attach the diverter valve to the adapter MC107 is des
44. tom of the riser at the angle stop valve b Install the 1 2 configuration at the top of the riser on a water supply line that does not have a slip joint nut at the angle stop valve c Install the 1 2 configuration at the angle stop valve if there is a 1 2 slip joint nut 3 8 112 there configuration configuration Install the Adapta Valve NOTE The Adapta Valve must be installed on the cold water line only 1 Shut off the cold water supply to the faucet by rotating the angle stop valve clockwise until the water flow is off Place a catch basin or other container below the faucet to catch any residual water in the pipes 2 Disconnect the cold water riser supply line at the angle stop valve or cold water faucet pipe Use an 8 adjustable wrench to rotate the slip joint nut counterclockwise until the riser supply line and slip joint nut detach from either the angle stop valve or the faucet pipe 3 Connect the Adapta Valve to the pipe from which you removed the slip joint nut a Align the Adapta Valve to either the angle stop valve or cold water faucet pipe making sure that the rubber washer is in place in the Adapta Valve b Use an 8 adjustable wrench to rotate the connection clockwise until tight DO NOT OVERTIGHTEN 4 Connect the cold water riser supply line with the slip joint nut to the Adapta Valve a Align the slip joint nut to the Adapta Valve b Use an 8 adjustable wrench to rotate the slip joint nut clockwis
45. tom port of the Tee adapter to plumbing Push the tubing until you feel resistance and then continue to push firmly until it is inserted as far as it will go Faucet stud 3 Fully insert the blue plastic tubing from the faucet or the tubing from the capacity monitor into the top port of the Tee Push the tubing until you feel resistance and then continue to Blue tubing push firmly until the tubing is inserted as far as it will go 4 Fully insert a separate 1 4 poly tube available through Multipure or a plumbing supplier into the side port of the Tee Provide sufficient tubing to reach your icemaker instant hot dispenser or other device and connect to that device a refrig FT or other device Housing Unit with Stainless Steel Faucet black wire from capacity Faucet stud indicator plate Blue tubing P d Tee refrig or other device S Iren SEV capacity monitor assembly Housing Unit with Capacity Monitor Faucet 16 3 5 Placing the System Under the Sink The Aquaversa models MP750SB and MP1200EL are designed to mount to the cabinet wall beneath the sink These systems can also sit on the cabinet floor with the use of an optional acrylic base If you would like to order the Aquaversa acrylic base please contact Multipure Customer Service at 800 622 9206 ext 175 1 Fasten the included mounting bracket to the wall ensuring it is in an upright position The
46. ued Reading the LED Display Plate 1 When you turn on the faucet or when the button on the FMU is pressed the LED on the LED Display Plate blinks five 5 times to indicate the filter capacity status The color of the LED indicates the filter status a Green 30 100 filter capacity b Orange 0 30 filter capacity mo c Red 0 filter capacity the FMU will also play a long audible sound to indicate 0 capacity 2 Multipure recommends ordering a new replacement filter either online at E http www multipure com store page6 html or by telephone at 800 622 9206 when the monitor indicates 30 capacity or less 3 The FMU will memorize the last remaining capacity in the event that the batteries lose power It will restore the last remaining capacity when new batteries are installed NOTE As with all drinking water treatment devices which reduce certain contaminants by mechanical filtration the capacity of the filter can vary and is dependent upon the type and level of contaminants in your water If the system is used on water with high levels of particulate matter Multipure recommends the installation and use of an additional pre filter element 3 3 Connecting to Your Plumbing Included with your MP750SB MP1200EL Drinking Water System is one installation kit which includes all of the fixtures and accessories needed to install your system below the sink If you determine that your particular plumbing configuration requ
47. white flakes or specks when the water is melted or boiled What causes white particles to appear in Multipure water when it Is frozen or bolled Many natural minerals in water are beneficial ta your health and their existence in drinking water in normal quantities is not cause for alarm Minerals can be removed by Reverse Osmosis technology which is available through the Multipure AquaRO Drinking Water System Why does the Multipure system reduce Volatile Minerals are dissolved in solution and do not have an actual physical size thus Organic Chemicals but not natural minerals the minerals pass through the system unfiltered In areas with excessive sedimentation pre filtration can help extend the operational efficiency of the Multipure filter however in most areas it is Unnecessary Should sediment be removed with a standard filter first Multipure Drinking Water Systems utilize a double filter mechanic The outer material is a pre filter that protects the solid carbon block from prematurely clogging with large sediment Multipure s densely compacted solid carbon block filters force water through microscopic pores of carbon much smaller than those of granular activated carbon thus more effectively reducing particulate matter and contaminants that affect the taste and odor of the water Why is the compressed solid carbon block filter more efficient than loose granular activated carbon filters Vater softeners a

owners manual-750-880-NEW

Contents

Download Pdf Manuals

Related Search

Related Contents