Home
VM-10 VT-20/VT-30/VT-50/VT
Contents
1. Power On Off Switch Charging Socket Use supplied charger only Power Indicator Fresh Battery The Power Indicator will illuminate for 1 second and extinguish after power is turned on Low Battery The Power Indicator will flash continuously indicating the battery level is low and needs to be recharged within 10 minutes Successful ACT syncing The Power Indicator will illuminate for 1 second and extinguish after channels are synchronized successfully Unsuccessful ACT syncing The Power Indicator will flash continuously for 5 6 seconds Check to see if different transmitter and receiver frequency bands are used ACT IR Port Align both receiver and transmitter ACT ports within 30cm of each other when the ACT button on the receiver is pressed for a successful ACT synchronization Charging Indicator Red LED indicator denotes charging Green LED indicator denoted charged and ready Fully charge may take up to 3 4 hours Connecting Cable and Connector Charging the ACT 20T VT e Power off transmitter e Plug the supplied charger into the AC mains input socket and then plug it into ACT 20T VT e Do not use charger from other brands to avoid insufficient voltage or current e Do not exceed the input supply voltage as it may damage the battery charger rechargeable battery and transmitter itself The output of MIPRO DC power supply is 12V 0 2A Viewing Charging Status e Charging Red LED indic
2. 20T VT Ideal for smaller crowds e VT 50 kit is designed with MIPRO ACT 515 true diversity receiver VT 20H and ACT 20T VT Ideal for medium crowds e VT 70 kit is designed with MIPRO ACT 717 ACT 727 ACT 747 true diversity receiver VT 20H and ACT 20T VT Ideal for large crowds in large professional venues Forcing adjusting slide jaw up amp down without pressing the side may damage the mechanical part 12 Violin Microphone Kit Violin Microphone Kit Connection ACT 20T VT Miniature Transmitter amp VT 20H Violin Transmitter Holder ACT 20T VT ACT 311 Align ACT 20T VT and slide into hot shoe of VT Once firmly in place adjust Adjusting Slide Jaw for ideal height and 13 14 VM 10 Wired Transmission Illustration Attach VM 10M onto VM 10H Clip VM 10H onto violin s tailpiece with the microphone placed over fine tuners Ascertain the microphone tip does not extend beyond the bridge so it will not interfere with bow during performance see diagram 4 Connect VM 10C Violin Microphone Cable onto a MIPRO MJ 53 Condenser Microphone Adaptor MJ 53 provides 12V 48V DC phantom power with a XLR output to the mixer input for a wired transmission see diagram 4 po 15 Illustration Shield GND Ground QAudio Short Disposal Dispose of any unusable devices or batteries f responsibly and in accordance with any applicable regulations Disposing of
3. a MIPRO MIPRO Electronics Co Ltd Headquarters 814 Pei Kang Road Chiayi 60096 Taiwan Web www mipro com tw ce FC 2CE461A AS120715 Design and specifications are subject to change without prior notice MIPRO VM 10 Violin Microphone Kit VT 20 VT 30 VT 50 VT 70 Wireless Violin Transmitter Kit User Guide Profile The musical instrument microphone kits are years of collaborations with professional musicians The key features are it fits snugly easy to install amp remove and protects the expensive musical instruments from surface scratches Strategically placed in discreet positions that will pick up accurate acoustic reproduction during performance without the handling movement and hitting noises amp IC ID THIS DEVICE COMPLIES WITH PART 74 OF THE FCC RULES AND RSS 123 ISSUE2 OF CANADA OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS 1 This device may not cause interference 2 This device must accept any interference including interference that may cause undesired operation of the device This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment ih VM 10 Violin Microphone Kit included components VM 10M Violin Microphone VM 10C Violin Microphone Cable VM 10H Violin Microphone Clip VT 20 Wireless Violin Transmitter Kit included components VT 20H ACT 20T VT Miniature Transmitter VT 30 Wireless Violin Transmitter K
4. ator e Charged Green LED indicator jg m S 2 35 x 0 7 Note Rechargeable batteries have a limited number of charge cycles and may eventually need to be replaced Battery life and number of charge cycles vary by useage and user settings VT 20 Wireless Transmission Illustration e Mount ACT 20T VT onto hot spot of VT 20H e Height of Adjusting Sliding Jaw ASJ can be adjusted by squeezing the side springs using the thumb and index finger together e Carefully mount VT 20H onto violin with thumb amp index finger in one hand and the thumb amp index finger in the other hand to adjust for ideal height amp tension see diagram 2 e VT 20 kit is designed for performers having existing MIPRO receivers e VT 20 kit includes VT 20H ACT 20T VT and requires VM 10H amp VM 10M Forcing adjusting slide jaw up amp down without pressing the side may damage the mechanical part 10 ACT 20T VT 11 VT 30 VT 50 VT 70 Wireless Transmission Illustration e Mount ACT 20T VT onto hot spot of VT 20H e Height of Adjusting Sliding Jaw ASJ can be adjusted by squeezing the side springs using the thumb and index finger together e Carefully mount VT 20H onto violin with thumb amp index finger in one hand and the thumb amp index finger in the other hand to adjust for ideal height amp tension see diagram 3 e VT 30 kit is designed with MIPRO ACT 311 ACT 312 diversity receiver VT 20H and ACT
5. it included components VT 20H Violin Transmitter Holder ACT 20T VT Miniature Transmitter Ideal for ACT 311 ACT 312 receiver VT 50 Wireless Violin Transmitter Kit included components VT 20H Violin Transmitter Holder ACT 20T VT Miniature Transmitter Ideal for ACT 515 receiver VT 70 Wireless Violin Transmitter Kit included components VT 20H Violin Transmitter Holder ACT 20T VT Miniature Transmitter Ideal for ACT 717 ACT 727 ACT 747 receiver VM 10M Violin Microphone Microphone Cable Connector VM 10C Violin Microphone Cable Q Connector Q Cable Q XLR Connector VM 10H Violin Microphone Clip VM 10 Wireless Transmission Illustration Violin Microphone Slot e Attach VM 10M onto VM 10H Q Violin Tailpiece Clip e Clip VM 10H onto violin s tailpiece with the microphone placed over fine tuners Ascertain the microphone tip does not extend beyond the bridge so it will not interfere with bow during performance e Connect VM 10M to VM 10C and to any MIPRO bodypack transmitter for a wireless transmission see diagram 1 VT 20H Violin Transmitter Holder Fixed Jaw Violin Transmitter Hot Shoe b Adjustable Sliding Jaw Diagram 1 Transmitter Receiver Transmitter Controls amp Indicators J T CHARGING I OFF ON MIPRO ACT 20T Transmitter
6. used batteries with domestic waste is to be avoided 2005 08 13 16 Batteries NiCad cells often contain heavy metals such as cadmium Cd mercury Hg and lead Pb that makes them unsuitable for disposal with domestic waste You may return spent batteries accumulators free of charge to recycling centres or anywhere else batteries accumulators are sold By doing so you contribute to the conservation of our environment
Download Pdf Manuals
Related Search
Related Contents
東芝空調吹出口取扱説明書 保管用 High Tech Pet PX-1SGT Instructions / Assembly USER MANUAL - LightTechnik VIZIO VS-03R User's Manual Inova CTPT-6LPZ User's Manual Manual - BenguFarm 取扱説明書 メモリーポータブルナビゲーション 品番 NV-M11 MANUAL DE UTILIZAÇÃO - cool-skk 「備えて安心 わが家の防災対策」 [PDFファイル/528KB] Copyright © All rights reserved.
Failed to retrieve file