Stylitis-200_B User Manual
Contents
1. Riva SES URN cue 18 12 INTERNAL GSM GPRS MODEM 19 13 SOFTWARE m 21 14 TECHNICAL 23 APPENDIX A CONNECTORS acus ca rnaina tUa pasdE gU FC FR 25 4 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 1 INTRODUCTION The Stylitis Power data logger is an instrument designed specifically for measurement of electrical quantities in power substations factories and other nodes where incoming and outgoing feeders are active It provides Q A local user interface with 240 x 128 graphic LCD display and touch screen Direct connection to S T and voltage points a Current transformer connection with up to 10 R S T and N incoming or outgoing feeders User selectable time interval for average calculations Internal flash memory 4Mb for data storage Programming control and data downloading via built in RS232 GSM modem and Ethernet interfaces Sampling and storage continues unaffected while communicating with the user WORKING WITH STYLITIS POWER The data logger operates in different ways according to your application see Fig 2 1 As an autonomous unit with off line data downloading The data logger samples the input signals and keeps the average values for each interval in the internal 4MB flash2. View NEUTRAL C POWER SUPPLY input S UME S200 003 STYLITIS POWER USER S MANUAL 0614 25 CONNECTOR NUMBERING SHOWN CORRESPONDS TO e Chassis Connectors Front View e Cable Connectors Back View I L2 I 3 I L3 I L1 DTR out GND A CTS in TXD 88 232 RTS out RXD in 26 S UME S200 003 STYLITIS POWER USER S MANUAL 0614
3. memory The stored files are downloadable via any of the built in interfaces The connection between data logger and the PC may be via a direct RS 232 link via a modem PSTN or GSM or via the Ethernet network LAN The PC must be equipped with an RS232 COM port a modem or a network card respectively The data logger is accompanied by Opton 4 the software required for programming inspecting data S UME S200 003 STYLITIS POWER USER S MANUAL 0614 5 downloading and decompression Data files are arranged in ASCII text files 2 Real Time Measurements On line data reading with appropriate user software for storing and manipulation in a PC The connection between data logger and the PC is as described above This manual includes detailed operation description Technical support is available by phone 30 210 6034002 or e mail support symmetron gr And at www symmetron gr 6 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 85 264VAC Fig 1 General Diagram GLCD touch Display input 1 LN Flash memory 4MB C T input 2 R 5 RS232 amp Ethernet Input Protection C T input 10 5 Ultra capacitors Voltage input 5 lsolated section Power Switch Each input module contains CPU memory and 4 channel analog to digital converter STYLITIS 10 USER S MANUAL Stylitis Power PC Fig 2 Operation
4. power and energy and power factor in up to 10 groups feeders of 4 lines each Current transformers must output an AC voltage up to 1 4 Volt RMS maximum proportional to primary current up to 6000 Amperes Conversion to physical units amperes is accomplished via the slope factor VOLTAGE GROUP There are 2 options for the voltage group 1 NOT USED The group is not recorded 2 280VAC Voltage Input A formula is applied to the measured value in order to convert it to appropriate physical units A user programmable parameter Slope is applied to measured value x Physical value Slope x The average of physical values is calculated and stored in memory for each statistical interval CURRENT GROUPS There are 2 options for each current group 1 NOT USED The group is not recorded 2 Y output Current Transformer Where Y is selectable 1 000 VAC 0 500 VAC 0 333VAC or 1mV A and it indicates the Current Transformer s voltage output type Besides the last option all the remaining ones indicate the CT s full scale output voltage and they also require the definition of the full scale S UME S200 003 STYLITIS POWER USER S MANUAL 0614 13 input current The 1mV A CT s maximum input current is 1400A because the logger s maximum voltage input is 1 4VRMS A formula is applied to the measured value in order to convert it to appropriate physical units A user programmable parameter Slope is applied to measure
5. the image above with which you can select the datalogger s power supply It may be external switch to EXTERNAL therefore you must apply a supply of 85 264 VAC in the corresponding connector on the rear part as it was mentioned before If you switch to INTERNAL the datalogger will be supplied by the voltage input if one has been connected in the corresponding connector It must be noted that in this case the input voltage must not be higher than 264 VAC upper limit of the power supply voltage Generally if the power supply is external the measured input can be up to 280 VAC 10 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 3 USER INTERFACE AND OPERATIONS REVIEW The touch screen GLCD display may be used to To see the datalogger s current status and time if the Acquisition is ON the recording interval and the memory status No option Starting menu To display the voltage current power and power factor input data values for all channels in tabular or bar graph form Display option Select R S T or N to select the phase to be displayed and Val or Bar for display of the values in tabular or bar graph form respectively To enable or disable the internal GSM modem Select Modem and then select Int Ext To check the modem signal and operator Select Modem and then select Check To display instruction pages concerning general information about user safety and the connectors pinout To
6. Automatic tab select the action for each weekday The automatic downloading is possible only after downloading and installing the AutoConnect software 22 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 14 TECHNICAL CHARACTERISTICS All accuracies stated are the mean of 5 measurements VOLTAGE INPUTS Input Voltage range RMS 0280 VAC Accuracy 0 25 of reading 0 1 of full scale Resolution 0 1 V Input Frequency range 47 63 Hz Accuracy 0 25 of reading 0 1 of full scale Resolution 0 01 Hz Frequency measured from first voltage channel e Differential input resistance 700 kohms e Maximum continuous over Voltage 350VAC INPUTS CH1 CH10 individually selectable in groups of 4 e Input Voltage range RMS from current transformer 0 29 1 45 VAC Accuracy 0 25 of reading 0 1 of full scale Resolution 0 01 A e Differential input resistance 20 kohms e Power Factor Measured for each phase Accuracy 0 5 of reading 0 2 of full scale e Power Active Reactive and Apparent for each phase Accuracy 0 5 of reading 0 2 of full scale INPUT PROTECTION e All inputs outputs are 4kV transient protected DATA PROCESSING AND STORAGE e RECORDED DATA TRMS Voltage TRMS Current Power Factor Frequency e INTERNAL MEMORY 4 Mbytes FLASH No battery backup required Operation mode is First In First Out Capacity all inputs at 15 minute averaging more than 100 days e REAL TI
7. ME CLOCK With automatic leap year correction Accuracy 7 5ppm 4 minutes year Backed up by internal long life Lithium battery COMMUNICATION PROGRAMMING AND DOWNLOADING e Built in RS232C port 9600 baud 8 bits no parity 1 stop bit Connector DB9M DTE When used internal modem is disabled e Built in GSM GPRS Quad band modem Connector SMA female When used RS 232C port is disabled e Built in 10Mbit Ethernet server Connector RJ 45 Always enabled SAFETY e Double insulated Complies with IEC60950 Built in Earth Leakage Circuit Breaker POWER SUPPLY e Built in universal power supply 85 to 264 VAC 47 to 63 Hz Input power source switch selectable internal or external e INTERNAL via voltage measurement channel L1 e EXTERNAL via 3 prong wall socket e POWER OUTAGES operates for at least 15 seconds without power and records time date of outage Energy storage medium Ultra capacitors S UME S200 003 STYLITIS POWER USER S MANUAL 0614 23 e POWER CONSUMPTION 5VA MAX VARIOUS ENCLOSURE IP67 sealed with carrying handle DIMENSIONS 27 x 24 6 x 17 4 cm 11275 cm3 WEIGHT 3kg CONNECTORS Removable circular connectors on left and right side OPERATING TEMPERATURE 0 465 OPERATING HUMIDITY 5 95 WARRANTY 1 Year 24 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 APPENDIX A CONNECTORS CONNECTOR NUMBERING SHOWN CORRESPONDS TO e Chassis Connectors Front View e Cable Connectors Back
8. R S MANUAL 0614 9 CONNECTORS On the two sides and on the rear part of the datalogger you can see the special polypolar circular connectors which need the appropriate cables adaptors which correspond to the descriptions on the upper part as you can see them in the image above RS 232 VOLTAGE EXTERNAL SUPPLY CURRENT 1 etc a On the right and left part of the instrument there are the input connectors of the voltage and the 10 current groups On the rear side there the Ethernet connector for connection of the instrument to the local network the RS 232 connector for connection of the instrument to a computer RS 232 serial COM port and the external power supply connector UPPER PART On the instrument s upper part see the image above besides the fuse there is also the graphic LCD touch screen the description and operation of which will be mentioned in detail in the next chapter Moreover there is an earth leakage relay RCD which must be switched to ON for the instrument to operate It will automatically switch to OFF in case there is a considerable difference between a live wire phase and the return wire neutral therefore there is a considerable leakage current to the earth which is dangerous for the user If you press the Test button this process will be simulated therefore the relay must switch to OFF for the circuit to operate correctly a Finally there is a switch POWER SWITCH in
9. STYLITIS POWER USER S MANUAL a SYMMETRON ELECTRONIC APPLICATIONS 0614 Copyright 2008 2014 SYMMETRON Electronic Applications Fourth edition in English June 2014 No part of this publication may be reproduced stored in retrieval system or transmitted in any form by any means without the prior written permission of Symmetron Company Information furnished by Symmetron is believed to be accurate and reliable however no responsibility is assumed for its use No license is granted by implication or otherwise SymmetronG is a registered trademark and Stylitis is a trademark of the Symmetron Company All other trademarks belong to their respective owners THE WARRANTY DOES NOT EXTEND TO AND SHALL NOT APPLY TO 1 Products which have been repaired or altered by other than Symmetron s personnel unless Buyer has properly altered or repaired the products in accordance with procedures previously approved in writing by Symmetron 2 Products which have been subject to misuse neglect accident improper installation or direct lightning strikes THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED ORAL OR WRITTEN EITHER IN FACT OR BY OPERATION OF LAW THE SYMMETRON COMPANY SHALL HAVE NO LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY KIND ARISING OUT OF THE SALE INSTALLATION OR USE OF ITS PRODUCTS RETURN FROM OUTSIDE GREECE Contact Symmetron for authoriza
10. Use wire up to 15 m for setup and data downloading Use a modem for setup and data downloading 30d c Z Su WAGOW NS9 JouaeWN USe J BUJ91U Wireless GSM Base modem station Use local network for setup and data downloading Voltage i Network etwor 54527 Ethernet card 10BaseT 8 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 2 OPERATION AND SAFETY EXTERNAL DESCRIPTION EXTERNAL SUPPLY ETHERNET 85 264 VAC 47 63Hz GSM SAFETY INSTRUCTIONS 1 This equipment using a suitable cable 2 Designed according to safely standard IEC 60950 1 3 Disconnect power supply and inputs before opening case 4 For added protection use fused voltage measurement leads 5 Current inputs must always be connected to current clamps 6 Referto user s manual for additional information SULA OSE N e1 2111 39V 110A POWER SUPPLY INTERNAL STYLITIS POWER Data Logger SULA Z N 1 2111 6 IN3yyno E EXTERNAL SYMMETRON FUSE 1A SLOW ELECTRONIC APPLICATIONS 8 IN3ayyno L AN333n025 FUSE REPLACEMENT The instrument uses a 1 A power supply fuse which must be CAUTION replaced if blown supply voltage out of limits It is located in the ZN front panel The fuse used must Make sure you have removed all external power supplies before of the specified attempting replacement rating Never shortcircuit the fuse holder S UME S200 003 STYLITIS POWER USE
11. c IP address of Diameson s PC if Diameson is running in a PC in your LAN use its local IP while if you are using Symmetron s Diameson its IP is 1 diameson net along with Diameson s User Listening Port default port number 8100 Double click the connection you created to connect 12 INTERNAL GSM GPRS MODEM You can enable disable the internal modem using the using the Modem menu from the touch screen LCD but also via Opton 4 software Read the logger s communication setup Read Communication Setup command from the Data logger online bar in the Setup tab and select in the COM1 node Communication Module Internal GSM GPRS modem in the first line and GSM data operation in the second line REMOTE via e g an Ethernet S UME S200 003 STYLITIS POWER USER S MANUAL 0614 19 connection see previous chapter Select Write Setup to save the changes To setup follow these steps 1 Disconnect all power supplies and remove the 4 screws on the front panel of the logger Raise the front panel and insert a Data SIM card in the modem the direction is shown on modem which according to the modem operation see below must support data or GPRS service Remember to permanently unlock the SIM card using any available cell phone before putting it in the modem Replace the 4 screws on the front panel of the logger 2 Power up the logger The GSM indicator on the logger has the following state
12. d value x Physical value Slope x The average of physical values is calculated and stored in memory for each statistical interval NOTES e The Opton 4 software can automatically set the Slope by specifying the Current Transformer s full scale input current and full scale output voltage if you have not selected a 1mV A CT as mentioned before Opton 4 may also calibrate all inputs current and voltage by setting the Slopes automatically e Finally you may define the phase shift between the voltage group and each current group separately 14 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 6 DATA PROCESSING AND STORAGE All inputs are sampled simultaneously at 2kHz rate and their values are placed in temporary storage True RMS values are calculated in 0 5 second intervals For precise results the calculations are based on the number of full cycles completed within a 0 5 second interval Cycles not completed within the averaging interval are accounted for in the next The averaging interval is selectable from 0 5 seconds to 1 hour in steps of 0 5 seconds At the end of the time interval the average values are calculated and stored stored simultaneously in the internal 4MB FLASH Memory and in the removable 2GB SD Flash card if one has been inserted along with a time mark corresponding to the end of statistical interval time NOTE For Stylitis Power F W versions that support SD cards the internal Flash memory is cyc
13. display genereal information of the instrument such as manufacturer and version About option S UME S200 003 STYLITIS POWER USER S MANUAL 0614 11 4 POWER SUPPLY There are 3 modes of operation NORMAL OPERATION MODE The instrument samples inputs at 0 5 second intervals and records averages of data from 0 5 second to 1 hour All functions are active DROPOUT MODE When voltage is lost the data logger records the date time of the event along with voltage and frequency values When voltage is restored the logger records the date time of the event end along with voltage values in a text file dropouts while a new data file opens When you download the data file the dropouts file is also downloaded The logger is capable to record dropouts even when its power supply is lost for up to 15 seconds display and communications are disabled for as long as there is no power supply SLEEP MODE If power supply is removed the logger keeps its real time clock running by supplying it by its internal Lithium battery All other activities are disabled 12 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 5 MEASUREMENTS Stylitis Power is capable of directly measuring voltage on up to 4 lines Connection Examples Frequency is measured on the first voltage line L1 22220212222 With suitable current transformers it is also capable of measuring current apparent power and energy active power and energy reactive
14. er is lost with acquisition ON the file will not appear in the card s file directory see next chapter therefore you will not be able to download it from the data logger but only to retrieve it via an SD card reader see next chapter 16 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 8 DATA RETRIEVAL File downloading and memory erasure are done via serial commands direct link modem etc using the accompanying Opton 4 software in the host PC See CHAPTER 13 Files downloaded to a PC are compressed to save memory space and speed up data transfer The data are retrieved using the Opton 4 software Data are decompressed to ASCII text files suitable for further manipulation using available programs like Excel etc Via the Download logger memory data from Opton 4 s Home tab or from the Data logger bar of the Files tab the following file downloading options appear If there is no SD card inserted in the data logger the data you will download are recorded in the internal Flash memory You may download 1 The most recent file The file closes before it is downloaded and a new file begins see previous chapter 2 One single previous file or more previous files You can type the number of a single file or a range of files e g 1 4 B If there is an SD Card inserted in the data logger the data you will download are recorded in the internal Flash memory and in the SD card simultaneously You
15. iameson client check box unchecked Double click the connection you created to connect 18 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 Via a static IP internet connection via a static IP ADSL router outside your PC s LAN In this case create a connection while offline by selecting New Connection in the Communication bar in the site s Connections tab In the connection s properties select the Ethernet radio button enter this static IP address along with the port number 50001 in the connection s properties Double click the connection you created to connect Via a dynamic IP internet connection via Diameson server outside your PC s LAN In this case do the following via Opton 4 In the communication setup click the COM2 node and select Ethernet Client operation Open the COM2 tree node open the CLIENT node and type the static IP address of Diameson s PC if Diameson is running in a PC in your LAN use its local IP while if you are using Symmetron s Diameson its IP is 62 38 244 17 along with the Diameson s Device Listening Port default port number 1023 Create a connection via Opton 4 software while offline by selecting New Connection the Communication bar in the site s Connections tab In the connection properties select the Ethernet radio button check the Diameson client check box and enter your Diameson user name Enter the stati
16. lic ie instead of getting full it continues recording from the beginning overwriting older files All files are be stored in the SD card Stored data in the FLASH memory is organized in files which are kept even without supply power For enhanced data safety each individual record is marked with its own time stamp S UME S200 003 STYLITIS POWER USER S MANUAL 0614 15 7 DATA RECORDING During recording acquisition on no change of parameters is permitted Only when acquisition is off parameter change is permitted Upon selection of acquisition ON the following happen 1 A new file is opened in the SD Flash if one has been inserted and the internal Flash memory 2 Recording starts according to user set parameters Upon selection of acquisition OFF the following happen 1 Recording stops 2 The file is closed in both memories When downloading the current file during recording 1 The file closes in both memories The download starts The recording is continued in a new file File downloading does not disturb the recording process Default data download is from file currently open Previous files can also be retrieved as explained in the next chapter NOTE To remove or insert an SD card to the data logger the acquisition must be OFF If it is ON when you insert it it will not be recognized and no data will be recorded in the card If you remove it with acquisition ON or in case pow
17. m the accompanying CD or download it from the Symmetron site Software upgrades are free to download Following the first installation go to the Sites bar in the center of the Start tab and click SHOW ALL The Sites tab will open In the Site Folder bar on the left select New Site Folder and choose a Windows folder to use as data storage for this specific data logger If you use several data loggers it is recommended to repeat this procedure choosing a separate folder for each one of them To work with the site folder you wish select it with a double click from the tree structure on the center part of the Sites tab The site will open in a separate tab which has the site s name SERIAL RS 232 CONNECTION AND OTHER CONNECTIONS In the next step determine how the PC will get connected to the data logger In order to create a serial RS 232 connection in Opton 4 select Connection in the Communication bar in the site s Connections tab In the connection s properties select the Serial RS 232 radio button and select the S UME S200 003 STYLITIS POWER USER S MANUAL 0614 21 PC COM port to which you will connect the data logger s serial port see CHAPTER 10 The serial port is not always active Either the serial port is active or the GSM GPRS modem You can enable disable the serial port using the using the Modem menu from the touch screen LCD After setting External you may con
18. may download 1 The directory of the card s files which appears in the Home tab in the SD Card directory bar The directory shows each file s number Start date size and start page so that you will know which file s to download 2 The most recent file The file closes before it is downloaded and a new file begins see previous chapter 3 One single previous file or more previous files You can type the number of a single file or select specific file numbers from the SD Card s directory by CTRL clicking them SHIFT clicking them etc in the Home tab in the SD Card directory bar Alternatively you may retrieve the SD card s files via an SD card reader In the Files tab in the Memory bar click SD Card gt VIEW From the appearing list select the SD Card drive you wish 9 DATA SAFETY Stored data in the internal FLASH memory and the SD card is organized in files which are kept even without supply power Data files are individually accessible Each record has its own time stamp S UME S200 003 STYLITIS POWER USER S MANUAL 0614 17 10 SERIAL PORT COMMUNICATION port DB9M e PIN2 Receive e PIN Transmit e PIN 5 Ground e PIN7RTS PIN 8 CTS Communication settings 9600 baud 8 data bits 1 stop bit no parity bit The Opton 4 software is used for communicating with the datalogger via your PC The RS 232 port is a DTE type i e Stylitis Power appears as a PC In order to u
19. nect a NULL MODEM serial cable to the PC COM port and double click the connection you created to connect You can create as many connections as you wish in a specific site folder For other connection types see the corresponding chapter For an Ethernet connection either via a dynamic IP or a static IP internet connection see CHAPTER 11 For a GPRS connection via a dynamic IP SIM card or for a GSM data call connection see CHAPTER 12 After connecting you can try some of the Opton 4 commands eg Get Status from Logger in the tab in the Status bar or Read Input Data in the Real Time tab etc To change logger channel settings go to the Setup tab and select Read Inputs Setup Then change settings in the tree structure and click Write Setup The same applies for the Read Communication Setup command see CHAPTERS 11 12 for communication options The settings can be changed only when data recording is stopped Acquisition Off Select Acquisition On to start recording To get stored data select Download logger memory data either from the center part of the Home tab or from the Data logger online bar of the Files tab To avoid missing data you can download files while Acquisition On For downloading options see CHAPTER 8 If you want to automate data downloading check the Enable Scheduled Automatic Connection box in the connection s properties and set the download time In the
20. open the NETWORK node type the settings of the SIM Card s provider APN USERNAME PASSWORD In the CLIENT node type the IP address of the host computer the one in which Diameson is running If this computer is in the same LAN with your computer even if it is your 20 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 computer type the local IP address Otherwise type the external one In the IP PORT field type Diameson s Device Listening Port the default value is 710237 In order to save the settings select Write Setup The data logger will be connected to Diameson within the next minute The next step is to connect via the GPRS network to the data logger from your PC any PC connected to the internet which will be also connected as a client to Diameson via a dynamic IP address Create the GPRS connection via Opton 4 by selecting New Connection in the Communication bar in the site s Connections tab In the connection properties select the Ethernet radio button check the Diameson client check box and enter your Diameson user name Enter the static IP address of Diameson s PC if Diameson is running in a PC in your LAN use its local IP while if you are using Symmetron s Diameson its IP is 1 diameson net along with Diameson s User Listening Port default port number 8100 Double click the connection you created to connect 13 SOFTWARE Install Opton 4 fro
21. s Flashing quickly Searching for Network Flashing slowly registered to the network idle continuously ON connected via data call 3 Wait until the INTERNAL MODEM indicator starts flashing slowly registered If the modem is set to GSM data mode see right below Select Modem and then Check from the menu of the datalogger s LCD touch screen to display the GSM network operator name and received signal strength see chapter 3 4 i GSM data call connection In Opton 4 create a connection by selecting New Connection in the Communication bar in the site s Connections tab In the connection s properties select the Seria RS 232 radio button select the COM port to which the PC modem is connected and enter the SIM data call number Double click the connection you created to connect Ii GPRS Connection via a dynamic IP SIM card In this case a cheap dynamic IP SIM card which supports GPRS connections is required The connection is possible via Diameson Gateway the Symmetron s server software For a GPRS connection connect to the data logger via an Ethernet connection via Opton 4 see previous chapter Check its setup Read Communication Setup command from the Data logger online bar in the Setup tab and select in the COM1 node Communication Module Internal GSM GPRS modem in the first line and GPRS Client operation in the second line REMOTE Open the REMOTE tree node
22. se the DB9 serial cables you must firstly connect the corresponding polypolic adaptor to the datalogger s RS 232 connector in order to connect the cables to its serial end A straight cable DB9M male to DB9F female is required for connection to an external modem A null modem cable DB9F female to DB9F female is required for connection to a PC The RS 232 port is enabled only when an internal modem is not used You can find more information about enabling and disabling the internal modem in chapter 3 USER INTERFACE AND OPERATIONS REVIEW 11 INTERNAL ETHERNET The internal Ethernet module of Stylitis Power is permanently activated To setup follow these steps 1 Power up the logger and connect the RJ 11 connector to the LAN Wait 30 seconds to allow LAN setup There are 3 communication options Via your LAN for local network connections In order to communicate via your LAN do the following In Opton 4 software in the Communication bar in the site s Connections tab click the Find Logger in LAN command The Digi Device Discovery window will open where you can see the IP address of the logger you are interested in Create a connection by selecting New Connection in the Communication bar in the site s Connections tab In the connection s properties select the Ethernet radio button enter this IP address along with the port number 50001 while leave the D
23. tion and shipping instructions SYMMETRON ELECTRONIC APPLICATIONS TEL 30 210 603 4002 FAX 30 210 603 4003 e mail infogsymmetron gr Internet http www symmetron gr Made in Greece 2 S UME S200 003 STYLITIS POWER USER S MANUAL 0614 CONVENTIONS USED IN THIS MANUAL Symbol Meaning To avoid injury of personnel and or damage to the instrument the operator must refer to the user s manual Calls attention to a procedure or condition which if not correctly performed could result in damage to the instrument S UME S200 003 STYLITIS POWER USER S MANUAL 0614 3 CONTENTS 1 rau Y xau ouo ag ada uud nuu uu icu 5 2 OPERATION AND SAFETY i nariniairhanusuu dai nu naa dana 9 3 USER INTERFACE AND OPERATIONS REVIEW 11 4 POWER SUPPLY aaaea iea ani 12 0 4 in 13 6 DATA PROCESSING AND STORAGE 15 RECORDING iid iuc hip 16 8 DATA RETRIEVAL 17 9 DATA SAFETY 17 10 SERIAL PORT 2 ecenasaun uc cuxaun nah nonu tuu 4 wo 0d qd ia c 18 11 INTERNAL
Download Pdf Manuals
Related Search