SERVICE MANUAL PROGRAMMING MANUAL
Contents
1. WT TENBORG Sware SERVI CE MANUAL PROGRAMMI NG MANUAL Kikko THE CONTENTS OF THIS DOCUMENT ARE I NTENDED FOR NECTA S AFTER SALES PERSONNEL NECTA SPA Manual PROGRAMMING KIKKO 1 27 INTRODUCTION The programming instructions described below are used to set the sales prices set any discounts move through the operating modes reset any failures that are indicated read the audit data and make test selections etc 1 OPERATING MODES The machine can be in three different operating modes and according to its mode the vending machine push buttons take on different functions 1 1 NORMAL OPERATING MODE 1 2 FILLER MENU 1 3 TECHNICIAN MENU Normal operating mode When switching the power on the display indicates for a few seconds the message Kikko and the installed software version The vending machine checks the boiler and if the boiler is empty a filling cycle is started automatically at the end of such cycle the heating phase starts then the machine goes into normal operating mode and is ready for making selections the push buttons perform normal operating functions and the display indicate the following messages on two lines Select drink Machine out of service Drink selected Wait please Take drink clock function The displayed massages indicating the operation being carried out are fixed while the message requiring an action from the user is blinking The2. NECTA SPA Manual PROGRAMMING KIKKO 23 127 Dispensing buttons BDV only This function enables or not the buttons on the coin mechanism used to release the coins in the change return tubes Value of exact amount BDV only This value defines the combination of empty coin tubes setting the coin mechanism in exact amount mode The possible combinations of empty coin tubes are indicated below For greater simplicity the combination is described with reference to tubes A B and C where tube A receives the lower value coins and tube C the greater value coins 0 A or B and 7 only 1 A and and C 8 Aor C only 2 A and only 9 Band C only 3 A and or C 10 B only 4 11 Bor C only 5 or only B default 12 C only 6 AorBorC C P C devices BDV only It dialogues with the coin mechanism if devices are installed or removed from the serial interface C P C type devices the monitoring unit is always enabled by default Minimum level of tubes It brings forward the Insert exact amount message for the user by adding a number of coins between 0 and 15 to the programmed number of coins to set the full change tubes status Free Vend BDV only Most payment systems with the BDV protocol control the free vend function However there are some payment systems without such function In this case if free selections are to be dispensed free vending must be enab
3. temperature C is the pressure espresso boiler temperature Press button to go back to the previous menu FILL 4 1 Instant Espresso FILL gt 4 Display boiler temperature The menu FILL gt 5 is used to make test selections complete liquid only powder only without accessories accessories v only Press button ED Lo access the sub menus and use buttons to scroll through them press button B 5 second time to confirm then press the desired selection button to make a TEST selection FILL gt 5 TEST Dispensing starts when pressing a button FILL gt 5 1 Complete selection FILL 5 2 ri LL 5 2 Dispensing starts when pressing a button Water only FILL gt 5 3 Id ih Dispensing starts when pressing a button Powder only FILL gt 5 4 FIL 2 4 Dispensing starts when pressing button No Accessories FILL gt 5 5 Accessories only pem s Dispensing starts when pressing a button The GSM menu FILL gt 6 control is used for being able to send a running out signal via GSM modem when a programmed number of pieces or grams of instant powder for a certain product have been used up With this function when activated the counters that control the pre alarms are reset FILL gt 6 GSM FILL gt 6 1 Reset pre alarm counters This is the initial menu of the section for the filler FILL gt 1 statistics switch the vending machine
4. 5 Aor B only described in the box where is default the tube with lower value 6 is the tube with higher 7 Aor B only lower value 8 Aor C only 9 Bor C only 10 B only 11 B or C only 12 C only TECH gt 2 1 2 1 C P C device BDV only v v NECTA SPA Manual PROGRAMMING KIKKO 12 27 ON Enable OFF Disable TECH gt 2 1 2 1 C P C device BDV only It communicates to AW the coin mechanism that the peripheral devices were installed or uninstalled Value TECH gt 2 1 2 1 AN xxxx 1 1 Exact change amount gt ON Enable OFF Disable ON Enable OFF Disable TECH gt 2 1 2 3 1 Fill tubes BDV only Manual change tube refill Manual release of one coin from the active tube AN TECH gt 2 1 2 3 2 elease BDV tubes Release tubes This option is used to set the E TECH 2 1 3 number of decimals after the N of decimals AV value The following is possible 1 one decimal 10 two decimals 100 three decimals gt lt TECH gt 2 2 1 1 Set water TECH gt 2 2 Selections The water and powder doses can be set for each selection button and therefore for each product composing the selection TECH gt 2 2 1 2 Whipper dose TECH 22 13 EV settings NECTA SPA Manual PROGRAMMING KI KKO 13
5. buttons 4N to move up or down one unit for each of the five figures When reaching the desired V V figure confirm with button 2 thus moving to the next figure nv From this menu it is possible to mask some menus enabled for the filler so that they are not visible and therefore cannot be used by the Filler After displaying the menus to be masked press buttons 4 W to enable ON or disable OFF then press button to return to the main menu TECH gt 2 6 5 1 Customised button v From this menu TECH 2 6 5 it is possible to store up to for special selections that are alternative to the standard 24 It is possible to decide to which button assign them replacing the standard selection in the layout 17 27 TECH gt 3 STATISTICS reset A V v NECTA SPA Manual PROGRAMMI NG The general counter stores all selections made since the last Total Statistics Display sales statistics by single selection for each time band and total Display total sales by single selection TECH gt 3 1 1 2 Display total complete vends in Display total normal operation and maintenance counters mode Display counters by selection Display failure counters since the last reset KI KKO TECH gt 3 2 3 mechanism counters Data on the machine operations is stored in both total counters and partial RELATIVE counters which can be
6. clock function display can be activated or deactivated through programming technician menu Filler menu when in normal operating mode press once only the Menu Access button located on the coin mechanism compartment the machine will go into maintenance mode filler menu and the display will indicate the message FILL gt 1 Statistics the other filler menus are Single Prices BDV tube control Boiler temperature Test GSM All these menus have a series of sub menus indicated in chapter 1 FILLER MENU Technician menu When in FILLER MENU mode press the button and the machine will go into Technician menu mode the display will indicate the message regarding the first menu TECH gt 1 Failures The other technician menus are Parameters Statistics Test Miscellaneous GSM All these menus have a series of sub menus see details in the specific chapter TECHNICIAN MENU 2 PROGRAMMI NG PUSH BUTTON FUNCTIONS The selection push button panel is used also for programming operations and in this mode the first three buttons take on the following functions EM T V Scrolling keys to go to the previous or to the e next menu option z i zit e o coo E Confirm key to go from a menu to sub menu or to T HE m M confirm the information on the display and NS i Exit key to go back from a sub menu to the higher level or Me 0 TER _ AM to confirm t
7. displayed and reset both partially and totally In addition it can be printed using the appropriate printer connected to the serial RS232 port 7 TECH gt 3 1 1 Displaying general statistics Total counters TECH gt 3 1 2 Reset counter TECH gt 3 2 1 gt 3211 Display Single counter Display sel counters TECH gt 3 1 1 3 Display sel counter N TECH gt 3 2 2 Display failure counters v TECH 32 3 1 Display coin Display audit data 18 27 TECH gt 3 2 3 Delete selection counters TECH gt 3 2 3 Partial delete Statistics Delete data by Selections v Discounts Overprice Failures Coin mech data TECH gt 3 2 3 Total delete Total delete of all statistical data TECH gt 3 4 11 Display single counters TECH 34 1 Display sel counters v RELATIVE STATI STI CS Display relative sales by single selection for each time band and total For relative is intended for the data from a certain point before the last reset TECH 3 3 12 Display Total counters v Display total sales by single selection Display total complete vends in normal operation and maintenance mode V Display sales by time band In normal operation and test mode v TECH 342 Display count by time bands Sales values with discount v TECH
8. mode the message Regenerate the water softener be displayed after set number of drinks dispensed AUTOMATIC CLEANI NG TECH gt 2 3 5 Option of setting the time when automatically washing the mixers and rotating the brewing units installed When setting the time to 24 00 the function is disabled default COLUMN ROTATION DELAY TECH gt 2 3 6 This function is used to set the delay time in stopping the cup column rotation in order to compensate any inertia due to the cup type ENERGY SAVING TECH gt 2 3 7 In order to save electric energy when the machine is not in use this function is used to switch off boiler heating and or external lighting 2 switch off time bands can be programmed on a weekly basis the weekdays are identified by a progressive number 1 Monday 2 Tuesday etc The same time band cannot include days from different weeks If time bands are set overlapping the machine will remain switched on for the shorter period For example in order to set energy saving time bands to run the vending machine from 07 00 to 22 00 during the week and leave it switched off on the weekend the time bands should be set using the special menu as indicated in the table below sa 00 00 00 00 00 00 00 00 00 00 00 00 0000 Start DISPLAY TECH gt 2 4 LANGUAGE TECH gt 2 4 1 There is a choice of language selected among the ones included in the EPROM to be used for the messages on the display
9. of the parameters that can be configured Press button P again to access sub menu TECH gt 2 1 CASH then again button to access the next sub menu TECH gt 2 1 1 PRICES and so on for all other sub menus Press buttons AV to go to the next or previous item TECH gt 2 Programming parameters After displaying the desired menu confirm with button EP and the display will indicate the messages BAND SELECTION PRICE use buttons to change the sales price for each selection and for the four time bands when setting time band zero no time bands are programmed TECH gt 2 1 Cash The desired time band is set up B to 4 time bands are possible If setting to zero the function is v not activated TECH gt 2 1 1 Prices TECH gt 2 1 1 1 Single selection prices TECH gt 2 1 1 1 1 Price of Band 0 4 The price for such Selection selection is set by Price V means of buttons A V 1 TECH 2 1 1 2 Global prices of SELECTIONS The price for such selection is set The price for such selection is changed by means of buttons 4 V 1 TECH gt 2 1 1 2 1 BAND 0 4 BAND PRICE PRICE TECH gt 2 11 3 Time bands 5 Manual PROGRAMMING 10 27 av av NECTA SPA Manual PROGRAMMING KI KKO CLOCK When confirming the blinking values day month year and week day are entered one af
10. 2 3 3 Enable STOP button STOP BUTTON this function is used to enable disable the STOP coffee button operation TECH gt 2 3 4 N of selections With this function it is possible to set a maximum number of selections for maintenance TECH gt 2 3 5 Cleaning With this function it is possible to set the time for automatic cleaning AV when setting the time to 24 00 the function is disabled gt av AV With this function it is possible to set the delay time in stopping the cup column rotation in order to compensate any inertia due to the cup type P Energy saving parameters Time band 1 4 With this function it is possible to set an energy saving cycle switching off the boiler and the lighting when not needed 2 off time bands can be programmed on a weekly basis I ON When confirming the blinking values hour and minute for start of time band are entered one after the other If start and end values are set to 00 00 the time bands are not activated ON enabled OFF disabled gt NECTA SPA Manual PROGRAMMING KIKKO 15 27 There is an option of language selected among the available ones to be used for the messages on the display TECH gt 2 4 1 Name of language A V It is possible to enable the function PROMOTIONAL MESSAGE and if enabled it can be customised with a text of up to 4 lines v TECH gt 2 4 2 Promot
11. 27 TECH gt 2 2 2 1 Select Button Water Powder v Powder doses Water Dose TECH gt 2 2 2 2 Doser settings j gt ey gt Doser settings 05 1 g s s Dos 1 gr s Doser 1 g s TEES TECH 2 2 2 3 E TECH gt 2 2 2 3 8 Powder Product name Global powder Global Doses in grams Powder Product name Dose in g Selection Powder Product name TECH gt 2 2 2 3 Single gt TECH gt 2 2 3 8 Enable accessories Select Button Available accessories Cup Dispensing of sugar stirrer and cup can L Stirrer be enabled or disabled for each single Sugar v selection button ON enabled OFF disabled Select button ON enabled OFF disabled Each single selection button can either be enabled or disabled It is also possible to change the order of the selections associated to the push button panel V gt TECH gt 2 2 5 Button 1 Button 2 TECH 2 3 Machine parameters PARAMETERS it is possible to change a whole series of parameters for the machine operation Temperature this function is used to set the boiler s operating temperature Wash button it is possible to enable the functioning of the mixer wash button disabled by default v NECTA SPA Manual PROGRAMMING KIKKO 14 27 TECH gt 2 3 2 Enable wash button ON enabled OFF disabled TECH gt
12. 34 3 Display discount counters TECH gt 3 4 4 Display Failure counters Display relative failure counters v NECTA SPA Manual PROGRAMMING KI KKO 19 27 TECH gt 3 4 5 Display coin mechanism data In this menu it is possible to delete the relative statistics starting from the last reset Total statistics are not reset TECH gt 3 5 1 Partial delete v TECH 3 5 1 1 Partial delete Selections Data changes according to the protocol used Validators and Executive Cashed and sold data BDV Audit MDB Audit v TECH gt 3 5 2 Total delete TOTAL DELETE of all relative data TECH gt 3 7 1 Partial printout PRINTING TOTAL STATISTICS With the printer connected it is possible to print all data as displayed V TECH 3 6 2 TOTAL printout NECTA SPA Manual PROGRAMMING KI KKO RELATIVE STATISTICS Partial delete of data for Selections Discount overprice v Failures Coin mech data It is possible to display the total selection counters at start up by enabling or disabling with buttons v TECH 3 7 1 X Partial printout STATISTIC NAME Print data by selections time bands failures coin mech data 20 27 TECH gt 3 8 1 Partial printout PRINT RELATIVE STATISTICS PARTIAL AND TOTAL With the printer connected it is V possible to print all data as displayed but only the relat
13. Coffee release Counter Volumetric count Counter Full liquid waste Counter Air break Counter Coin mechanism Counter RAM data Counters FILL gt 1 4 4 Display coin mechanism data FILL gt 1 4 4 1 Display coin mechanism counters Press button key gt to confirm the displayed information and buttons AV to scroll through the items to be displaved FILL gt 1 4 4 2 Display cash counters 5 27 In this menu FI LL gt 1 5 it is possible to delete and reset the relative statistics partially for each selection or globally FILL gt 1 5 1 1 Partial delete CONFIRM FILL gt 1 5 FILL gt 1 5 1 FILL gt 1 5 1 1 Delete relative statistics partial delete Partial delete Selections Time bands Failures Coin mech data Press button Bf to access the sub menu FILL gt 1 5 1 press it again to access the sub menu FILL gt 1 5 1 1 use buttons Ax to scroll through the selections when pressing a second time button the request message is displayed then press is again to doa partial delete In the menu CAR gt 1 5 2 it is possible to delete the relative FI mc FILL 1 5 2 1 statistics globally and reset the counters FILL gt 2 Prices E The menu FI LL gt 2 is used to change the sales price for each selection and for four different time bands When setting Time Band 0 no time bands are pro
14. ENABLE PROMOTIONAL MESSAGE TECH gt 2 4 2 When in this menu press the confirm button A to display the status of the message enabled or disabled The status can then be changed using buttons v SETTI NG THE PROMOTI ONAL MESSAGE TECH gt 2 4 2 2 The 4 line message be written using buttons AW to scroll through the available characters Press the confirm button the first character will start blinking and can be modified The message is stored by pressing button lt CUSTOMI SE MESSAGES TECH gt 2 4 3 The machine uses standard messages to give information to the user during normal operation e g Ready Take etc When this function is enabled the message can be changed in the same manner as setting the promotional message Changes are stored as copies of the standard messages Therefore if this function is disabled the standard messages will be displayed again but the changed messages are still stored PRE SELECTI ONS TECH gt 2 5 There is the option of enabling some selection buttons to have dispensing Without cup With extra sugar i e a greater amount of sugar programmable on all selections where it is dispensed Unsweetened i e without sugar on all selections where it is dispensed Mokka i e with a reduced amount of water programmable for coffee The and buttons can be used to vary the amount of sugar or alternatively of coffee The LEDs will indicate the average dose chan
15. HANGE BUTTON is used to activate the change return without vending ON activated OFF deactivated TECH gt 2 1 2 1 BDV data TECH gt 2 1 2 1 of vending Change button ON OFF 11 27 Press button ur to access the sub menus and buttons Ax to go the available options then press button to confirm the choice The MAXI MUM CREDIT function is used to set the maximum credit value that can be inserted NY The MAXIMUM CHANGE function is used to set the maximum CHANGE value setting between 0 and 250 base coin VALUE gt The ACCEPTED COINS function is used to define which among the coins recognised by the validator are to be accepted Coins Coins YES Enable NO Disable 16 coins available identified with numbers 1 16 press the confirm button to access Accepted change buttons to enable or disable This sub menu is used to set which coins are to be accepted as change and to enable ON or disable OFF the change function It is possible to enable or disable a selection button with MEE ON Enable OFF Disable Value of exact amount BDV only 0 Aor C 1 A and B and C 2 A and B only 3 Aand or This function defines the combination of empty coin tubes setting the coin mechanism in EXACT AMOUNT mode 4 Aonly possible combinations
16. LURES RESET FAI LURES delete TECH 1 FAILURES KTERNAL LAMP STATUS PRICES COIN MECHANISMS CASH DECIMAL POINT TECH 2 PROG WATER DOSES SELECTI ONS POWDER DOSES ACCESSORIES SELECTION STATUS SELECTION BUTTON PARAMETERS VENDI NG MACHI NE PARAMETERS BOILER TEMPERATURE WASH BUTTON STOP BUTTON TANK N OF MAINTENANCE SELECTIONS AUTOMATIC CLEANI NG COLUMN TURN TIME ENERGY SAVING DI SPLAY LANGUAGE PROMOTIONAL MESSAGE CUSTOMISING MESSAGES NECTA SPA Manual PROGRAMMING KIKKO 8 27 PRE SELECTIONS TECH gt 2 follows NO CUP EXTRA SUGAR LESS SUGAR MORE SUGAR LESS WATER MOKKA MORE POWDER LESS POWDER ESPRESSO COFFEE POWDER MI SCELLANEOUS JUG FACILITIES SETTING THE N OF SELECTIONS PASSWORD ENABLE THE PASSWORD REQUEST TECH gt 3 STATISTICS GENERAL COUNTER READ AND DELETE DI SPLAY SELECTION COUNTERS DELETE PARTIAL AND TOTAL DI SPLAY RELATIVE STATISTICS SELECTION COUNTERS DELETE RELATIVE STATISTICS PARTIAL AND TOTAL DI SPLAY COUNTERS AT START UP PRINT PARTIAL PRINT RELATIVE STATISTI CS PARTIAL AND TOTAL TECH gt 4 TEST COMPLETE WATER ONLY POWDER ONLY DISPENSING WITHOUT ACCESSORIES ACCESSORIES ONLY UNIT ROTATION COFFEE RELEASE BOILER EMPTYING MANUAL INSTALLATION SPECIAL FUNCTIONS ACTUATION IN A SEQUENCE OF DOSER DEVICES ELECTRIC MIXERS CUP RELEASE STIRRER RELEASE FLUORESCENT LAMPS DOOR LEDS INSTALLATION DATE PUSH BUTTON
17. OLD SETTINGS TECH gt 6 2 This function is used for setting the number of selections for each product after which a running out pre alarm signal is sent via modem RESET COUNTERS TECH gt 6 2 2 With this function the counters that control the pre alarms are reset NECTA SPA Manual PROGRAMMING KIKKO 27 127
18. S MOBILE SPOUTS MACHINE pe IDENTIFICATION 5 COFFEE UNIT ROTATION WASTE CONTAINER FULL INFORMATION OPERATOR CODE AUTO TEST TECH gt 5 MISCELLANEOUS INITIALI SING DATABASE COUNTRY LANGUAGE MACHINE TYPE INITIALISING TECH 6 GSM Set THRESHOLDS PRODUCT NAME GRAMS RESET PRE ALARMS gt CONFIRM Manual PROGRAMMING KIKKO 9 127 NECTA SPA TECH gt 1 FAILURES In this menu the present failures can be displayed and then deleted RESET Press button access the sub menu TECH gt 1 1 Display failures TECH gt 1 Press button ur MN access the sub menu TECH gt 1 1 Confirm with button to display the present failures automatically and one after the other at FAILURES x timed intervals at the end the message END OF FAI LURES will be displayed press button to return to the previous menu TECH gt 1 1 Display failures MONITORED FAI LURES Water failure Liquid waste full Air break failure Cup failure Mobile spouts Volumetric counter Boiler Machine control board Coffee unit Coin mechanism TECH gt 1 1 End of failures Use buttons to go from sub menu 1 1 to the following sub menus 1 2 1 4 and in TECH gt 1 3 Reset failures RESET FAILURES Done the same manner after pressing button to access the menu operate as indicated TECH gt 2 This menu is used to adjust all
19. ailable menu FILL 1 STATISTICS In this menu it is possible to display and print statistical sales data the failure list coin mechanism data photocell errors and motor errors see list at page xy Press button to access the sub menu FILL gt 1 1 PRINT STATISTICS Press again button to access sub menu FILL gt 1 1 1 PARTI AL PRINTOUT Press again button i to access the different items of the sub menu Press again button Ep to display the sub menu FILL gt 1 1 1 1 COUNTERS The buttons AW are then used to display the relevant counters Press again button the display will indicate the message CONFIRM PRINT At this point connect the printer before confirming Press again button to start printing On the other hand to print total statistics press buttons to display FILL gt 1 1 2 TOTAL PRI NTOUT then proceed as above to continue and obtain a total printout FILL gt 1 1 1 1 Selection counters Press buttons AV to display the menu FILL gt 1 2 PRINT RELATIVE STATISTICS This menu is used for printing relative statistics starting from the last reset without touching the total statistics memory Relative statistics are useful for determining sales or other information starting from a certain date last reset until the date when the information is displayed or printed When the menu is shown on the display proceed exactly as above to access the sub menus Press button again to ac
20. ally and then change the figure of the selections with different prices TIME BANDS TECH gt 2 1 1 3 Four programmable time bands are provided for selling products at different prices The time periods are programmable for beginning and end time by hours 00 to 23 and minutes 00 to 59 If the values for start and end of the time band are set to 00 00 the time period is disabled The reference time is kept by an internal clock programmable as day month year weekday 1 7 and then hour minutes seconds If the values for start and end of the time band are set to 00 00 the time period is disabled COIN MECHANI SMS TECH gt 2 1 2 It is possible to decide which of the payment system protocols available are to be enabled for the functions The available payment systems are Executive Validators BDV MDB By selecting one of the systems it is possible to control its functions EXECUTIVE TECH gt 2 1 2 1 The following payments systems are available for the Executive system Standard Price Holding Coges U Key Button function diagram for programming VALIDATORS TECH gt 2 1 2 1 When the Validat Lines line setting function of the Technician menu is displayed the value of the 6 validator coin lines A F can be changed BDV MDB The BDV and MDB protocol menus are relatively similar The following structure shows the differences Type of vending Setting the operating mode for multiple or sing
21. ays the counter for the number of sales with discounts and overprice FILL gt 1 3 3 Display discount counters Tot V This menu displays the type and number of failures occurred and monitored by the software listed below Press button Bb access to the list and buttons A to scroll through the list Press buttons to display the present FILL 21 3 4 Water failure Counter failures and the number Boiler Counter of failures occurred since Mobile spouts Counter the last total reset Cup failure Counter Coffee unit Counter Coffee failure Counter Coffee release Counter Volumetric count Counter ay Full liquid waste Counter Air break Counter Coin mechanism Counter Machine control board This menu displays the coin mechanism data according to the protocol used with cashed values and sold values Press buttons X to display data regarding Validators and Executive Cashed and sold BDV Audit MDB Audit Total cashed Total FILL gt 1 3 5 2 Cash display 4127 Press button N V FILL gt 1 4 Display v Relative statistics This menu CAR gt 1 4 displays the relative statistics and more specifically The number of sales by single selection for each time band and total relative after the last statistics reset to a
22. button and the message AUTO TEST will start blinking Confirm by pressing THE SAME BUTTON to start the auto test cycle In a sequence 1 the doser devices are activated for 2 seconds 2 the mixers are activated for 2 seconds 3 is released 4 a stirrer is released 5 the fluorescent lamps are switched on 6 the door LEDs are lit 7 the push button panel is tested the machine will display the number of the button which must be pressed and awaits the actuation before going to the next button 8 the dispensing spouts are operated repositioned 9 for espresso models only the coffee unit is rotated coffee is ground and then released when a full dose is reached 10 waste container switch the machine awaits until the waste container microswitch is manually operated MI SCELLANEOUS gt 5 This menu contains some sub menus used less frequently which permit control of the functions described below MACHINE INFORMATION TECH gt 5 1 INSTALLATI ON DATE TECH 5 1 1 This function is used to store the current date of system as installation date The date is printed when retrieving the statistics PROGRAMMI NG THE MACHI NE CODE TECH gt 5 1 2 When the MACHI NE CODE function is displayed the eight digit numeric code identifying the machine can be changed from the default 0 PROGRAMMI NG THE OPERATOR CODE TECH gt 5 1 3 When the OPERATOR CODE function is displayed the six digit numeric code ident
23. ccess the sub menus and LI to scroll through the other sub menus FILL gt 1 5 Delete relative statistics av ny NECTA SPA Manual PROGRAMMING KI KKO Press buttons py to display the counters by single selection and for each time band and total FILL gt 1 4 1 Display sel counters FILL gt 1 4 1 1 Display single counters FILL gt 1 4 1 1 Display single counters Selection 1 FILL gt 1 4 1 1 Display single counters Selection 1 Band Press buttons ANN to display total sale by single selection FILL gt 1 4 1 2 Display total counters Selection 1 Tot FILL gt 1 4 1 2 Display total counters Confirm with to display the counters for the time bands Press buttons to display the sales values for each time band FI LL gt 1 4 2 Counter by time bands FILL gt 1 4 2 X Counters by time bands Band 0 counter Band 1 counter Band 2 counter Band 3 counter Band 4 counter Press buttons to display the present failures and the FILL gt 1 4 3 Display failures FILL gt 1 4 3 x Water failure Counter number of failures Instant boiler Counter occurred since the last Espresso boiler Counter total reset Mobile spouts Counter Cup failure Counter Coffee unit 1 Counter Coffee unit 2 Counter Coffee failure Counter
24. cess the sub menu CAR gt 1 2 1 PARTIAL PRINTOUT then proceed as above Press button to access the counters menu and confirm printing then use buttons V to go to the next counters menu or to the previous menu FILL gt 1 2 1 1 Selection counters FILL gt 1 2 1 2 Time band counters FILL gt 1 2 1 3 Failure counters FILL gt 1 2 1 4 Coin mech counters 3 27 NECTA SPA Manual PROGRAMMING FILL gt 1 3 Display Statistics FILL gt 1 2 2 Total printout FILL gt 1 3 1 Display counters by selection FILL gt 1 3 2 Display counters by time bands FILL gt 1 3 3 Display discounts FILL gt 1 3 4 Display failures FILL gt 1 3 5 Display coin mech data KIKKO Printina Total counters In this menu it is possible to display the number of sales for each single selection for each time band and the number of total sales for each single selection press button to zi access the sub menu FILL gt 1 3 1 then proceed as above After displaying the selection use buttons AV to go to the next selections and button to go back to the previous menu Selection Band FILL gt 13 1 1 Single selection counters by time band FILL gt 13 1 2 Single selection total counters This menu displays the counter for the number of sales by time bands 7 band 0 4 Counters ay This menu displ
25. d For the failures monitored by the internal software of the vending machine Or A pre alarm signal if programmed and activated or later an End of product signal for a given item or for any selection TECH gt 6 2 from this sub menu it is possible to totally reset the counters that control the End of product pre alarm signals NECTA SPA Manual PROGRAMMING KIKKO 22 27 SUMMARY OF ALL FUNCTIONS AND SUB MENUS AND SPECIFIC APPLICATIONS FAI LURES TECH gt 1 READING PRESENT FAILURES TECH gt 1 1 When the Failure item is displayed press the confirm button to display the present failures If no failures are currently present after pressing the confirm button the message END FAILURES will be displayed RESET PRESENT FAI LURES TECH gt 1 2 When the Reset failures item is displayed press the confirm button to reset the present failures PROGRAMMI NG PARAMETERS gt 2 CASH TECH gt 2 1 This set of functions controls parameters regarding the payment systems the sales prices SELECTION PRI CES TECH gt 2 1 1 Four different prices can be set for each selection according to the programmed time bands for when the time table option is enabled For each of the 4 time bands the prices 0 to 65 535 can be programmed globally same price for all selections or for the single selections Should the majority of products be sold at the same price it will be convenient to set the price glob
26. ge Strong light i e varying the amount of product programmable for coffee Espresso i e varying the amount of water adjustable for coffee selections Coffee powder i e varying the amount of product adjustable for instant and fresh brew coffee For each pre selection it is possible to decide whether or not it is to be enabled which button will be assigned to the selection price change and the percentage change in product dose MI SCELLANEOUS TECH gt 2 6 JUG FACILITIES TECH gt 2 6 2 Some models supplied with a special button permit dispensing of a number of selections programmable between 1 and 9 5 by default without cup to fill a jug NECTA SPA Manual PROGRAMMING KIKKO 25 27 PASSWORD TECH gt 2 6 3 It is a 5 digit numeric code which is required to access programming The default value of this code is set to 00000 ENABLE PASSWORD TECH gt 2 6 3 1 This function is used to enable the option of requesting the password to access programming the password request is disabled by default FILLER MENU MASKING TECH gt 2 6 4 This function is used to determine the filler menu options to be left active or to be disabled The reference numbers of the menus do not change even if some are disabled BUTTON CUSTOMISED TECH gt 2 6 5 The machine has the option of customising up to four selections as alternative to the standard ones With this function it is possible to decide to which button assign
27. grammed FILL 22 1 2 FILL gt 2 1 1 gt Set global prices Band Price FILL gt 2 2 FILL gt 2 2 1 Set single prices Band Price Press button to access the sub menu for the time bands press buttons to scroll through the time bands then press again button ur to display the selection menu combine with a price shown blinking use the buttons b to change the set figure then press button to confirm the operation The menu FILL gt 3 is used to load FILL gt 3 1 or empty FILL gt 3 2 the change tubes manually FILL gt 3 When confirming with button a the display indicates the message Fill BDV tubes confirm again and the display will indicate the message Credit which is the value of money Change tubes control available in change the tubes when inserting the desired coin into the selector the display will increase the value of money available in the change tubes In this sub menu FILL gt 3 1 it is possible FILL gt 3 1 FILL 3 1 to load the BDV change tubes manually Fill tubes Fill tubes Use the buttons to i choose the relevant tube FILL gt 3 2 Release tubes FI 3 2 and then press button gt Release BDV tubes Credit Tube A X to release or load one coin at the time from the active tube NECTA SPA Manual PROGRAMMING KIKKO 6 27 Press button BB to display the boiler s instantaneous temperature Considering that I is the open top instant boiler
28. hat active data M f i 7 PME Programming is divided into two main modes FILLER MENU gt 1 6 TECHNICIAN MENU TECH gt 1 6 FILL gt 1 STATISTICS TECH 1 FAILURES FILL 2 PRICES TECH gt 2 PROG PARAMETERS FILL gt 3 BDV MDB TUBE CONTROL TECH gt 3 STATI STI CS FILL gt 4 DISPLAY BOI LER TEMPERATURE TECH 4 TEST FILL gt 5 TEST TECH 5 MISCELLANEOUS FILL gt 6 GSM TECH 6 GSM NECTA SPA Manual PROGRAMMING KIKKO 2127 1 FILLER MENU RS 232 port Wash cycle button Programming access button FILL gt 1 1 Print statistics and for printing v FILL gt 1 2 Print relative statistics NECTA SPA Manual PROGRAMMING KIKKO FILL gt 1 1 1 Partial printout FILL gt 1 1 2 Total printout FILL gt 1 2 1 Partial printout FILL 1 2 2 Total printout With the vending machine in normal operating mode press once the menu access button located on the inside of the door on the coin mechanism compartment and the vending machine will go to the Filler menu The keys scroll through the filler menu items which are as follows Statistics Single Prices BDV tube control Special selections Test Each of these menus has a series of sub menus accessed by means of the selection buttons as indicated in the previous page After pressing the menu access button the display will indicate the first av
29. ifying groups of machines can be changed from the default 0 INITIALISING TECH 5 2 When the Initialise function is displayed the vending machine can be initialised restoring all default data This function should be used if there is a memory data error or when the software is replaced All statistic information will be reset Press confirm button to display the message Confirm Press again the confirm button and some parameter are requested and namely MODEL Defining whether the machine is Espresso or Instant COUNTRY Intended as type of doses to be used for the selections e g IT coffee 45 cc FR coffee 80 cc The available countries are IT FR ES LAYOUT A number of Button Selection combinations to choose from are provided for each dose type model the combinations available for each layout are indicated in the dose selection table supplied with the machine TANK This function is intended as water supply from a tank It can be enabled or disabled water supply from the mains When confirming the option the message Working is displayed for a few moments GSM rEcH gt 6 The control software can sent a machine failure signal or a running out pre alarm signal via GSM modem when a programmed number of selections for a certain product PIN CODE TECH gt 6 1 This function is used to program the identification codes that will be sent to the GSM modem optional THRESH
30. ing is displayed for a few seconds all statistics are reset DISPLAY COUNTERS TECH gt 3 5 This function is used to enable disable the display of the total number of sales since the last statistic reset during the start up phase of the machine PRINT TECH 3 6 Connect an RS232 serial printer having a Baud rate of 9600 8 data bit no parity 1 stop bit the CITIZEN I DP 3110 24RF 230A p n 9210219 printer is recommended to the serial port located on the push button board to print all of the statistics described in the paragraph statistics display The printout will also contain the machine code the date and the software version Statistics can be printed partially or totally To connect the printer do as follows press the confirm print button displaying the message Confirm connect the printer before confirming press the confirm button to start printing TEST TECH gt 4 COMPLETE DISPENSING TECH gt 4 1 This function is used to get a complete selection with the door open without inserting any money SPECIAL FUNCTIONS TECH gt 4 2 After accessing this function it is possible to 1 Activate the coffee unit 2 Grind and release a coffee dose 3 Open a solenoid valve to let air in for boiler emptying Install the boiler manually NECTA SPA Manual PROGRAMMING KIKKO 26 27 AUTO TEST TECH gt 4 3 This function allows testing of the main machine components Press the CONFIRM
31. ion of product dose values the flow rate of the single dosing units expressed in g s can be set to calculate the amount of powder to be dispensed It is also possible to program the doses of a product Globally i e setting all selections with a single operation ACCESSORIES TECH gt 2 2 3 Dispensing of sugar stirrer and cup can be enabled or disabled for each single selection button as well as the water supply from an internal tank SELECTION STATUS TECH gt 2 2 4 Each single selection button can either be enabled or disabled BUTTON SELECTION ASSOCIATION TECH gt 2 2 5 This function is used to change the order of the selections associated to the push button panel VENDI NG MACHINE PARAMETERS TECH gt 2 3 TEMPERATURE TECH gt 2 3 1 This function is used to set the operating temperature expressed in C for the boilers actually installed in the machine After selecting the boiler press the confirm button the temperature value starts blinking on the display and can be modified as necessary ENABLE WASH BUTTON TECH gt 2 3 2 This function is used to enable the functioning of the mixer wash button see Fig 1 Normally the button is disabled STOP COFFEE TECH gt 2 3 3 This function is used to enable disable button which stops coffee selections during normal operation NECTA SPA Manual PROGRAMMING KIKKO 24 27 SETTING THE REGENERATION COUNTER TECH gt 2 3 4 Upon accessing Filler menu
32. ional message Press buttons to scroll the through letters of the alphabet and button e to confirm the letter and go to the next one Press button to ao to the previous messaqe TECH 2 4 2 2 Set message text TECH gt 2 4 2 Customise messages Press buttons ay to scroll the through letters of the alphabet and button ur to confirm the letter and go to the next one Press button to ao to the previous messaae TECH gt 2 4 2 2 Set message text TECH 2 5 1 Pre selections Name of pre selection NO CUP SUGAR ON enabled 2 is the e LESS SUGAR OFF disabled enabling some selection MORE SUGAR buttons to have MOKKA V V dispensing differing from STRONG the default settings see LIGHT box ESPRESSO COFFEE POWDER v NECTA SPA Manual PROGRAMMING KIKKO 16 27 TECH gt 2 6 2 TECH gt 2 6 2 Jug Facilities Jug Facilities Number of selections TECH gt 2 6 4 Filler menu masking TECH gt 2 6 5 Custom selection TECH gt 3 Manual PROGRAMMI NG From this menu TECH gt 2 6 2 it is possible to set the number of selections for free V JUG dispensing to be activated with a key Values of 1 to 9 can be set TECH gt 2 6 3 Password ON enabled OFF disabled A five figure password can be v set from this menu E The default value of is set to 00000 and the password is not requested Press
33. ive ones from a certain point Before a reset The printable data is the same as the total statistics TECH 3 8 2 Total printout Heading current date machine model SW version operator and machine codes installation date Printable statistics dispensing by Complete selections water only powder only without accessories accessories only From this menu it is possible to make complete selections without inserting the money or with the options indicated It is also possible to activate the special functions for specific tests TECH gt 4 2 TECH 4 1 X Complete selection Water only Powder only No Accessories Accessories only av Press a button to start complete dispensing with all accessories sugar cups stirrers or scroll through the other items of the menu with buttons ANN AVAILABLE SPECIAL FUNCTIONS Coffee unit rotation Coffee dose release Boiler emptying TECH gt 4 2 x FUNCTION NAME ay TECH gt 4 3 Autotest av From this sub menu TECH gt 4 3 it is possible to auto test the functional units Confirm with button ur to activate in a sequence the following functional units Dosers devices whippers cup dispenser stirrer dispenser fluorescent lamps door LEDs push buttons mobile spouts coffee dose unit rotation full waste container The units marked with an asterisk must be activated manually by the personnel performing the test The fu
34. le dispensing With multiple dispensing The change is not automatically returned after a successful selection however the credit is available for further selections When pressing the coin return button the available credit is returned if its value is lower than the maximum change value Credit control This function enables disables the return of credit if no selections is made If enabled this function will hold the credit until the first selection has been made If however a selection fails for any reason the change will be returned if requested Maximum credit This function is used to define the maximum accepted credit Maximum change It is possible to set a limit to the total amount of change returned by the coin mechanism when pressing the coin return button or after a single dispensing serving The value can be 0 to 250 basic coins Any credit exceeding the amount programmed with this function will be cashed Accepted coins It is possible to define which among the coins recognised by the validator are to be accepted Check the label on the coin mechanism for the correct coin to value matching indicating the position of the coins Rejected coins BDV only This function programs the rejection of coins when in exact amount mode Check the label on the coin mechanism for the correct coin to value matching indicating the position of the coins Disabled coin return MDB only This function disables the return of a specific coin
35. led with VMC Vending machine control disabled by default and the price of the selections must be set to zero Immediate change BDV only According to the BDV protocol the amount of credit inserted for a selection is cashed after the machine sends the message Selection successful When this function is enabled disabled by default the cash message is sent at the beginning of dispensing DECI MAL POINT TECH gt 2 1 3 Press the confirm button to display the position of the decimal point i e 0 decimal point disabled 1 XXX X 2 XX XX XXX Press the confirm button these values will start blinking and can then be modified as necessary SELECTIONS TECH gt 2 2 The selection menu is composed of various sub menus which allow setting of the different parameters WATER DOSE TECH gt 2 2 2 1 The water dose expressed in cc can be set for each selection button and therefore each product assigned to it the display indicates the name of the product being selected It is also possible to set the water flow rate of the single solenoid valves expressed in cc s the default value setting in cc s is indicated in the selection dose table to calculate the amount of water to be dispensed POWDER DOSE TECH gt 2 2 2 2 The powder dose expressed in grams can be set for each selection button and therefore each product assigned to it the display indicates the name of the product being selected For correct convers
36. ll waste container requires manual triggering of the microswitch The push buttons need to be pushed by the operator t TECH 5 MISCELLANEOUS NECTA SPA Manual PROGRAMMING KI KKO 21 27 TECH gt 5 1 1 Installation date TECH gt 5 MISCELLANEOUS MI SCELLANEOUS This menu contains some sub menus used less frequently which permit control of the following functions TECH gt 5 1 2 MACHINE INFORMATION Machine code Installation date Machine code Operator code The above data can be entered and changed INITIALISING This menu is used to initialise the installed software restoring all default data TECH gt 5 1 2 Operator code v v This menu TECH gt 5 2 is used to set the data necessary for initialising the machine regarding the country the language and machine type at the end the data need to be confirmed to perform initialising After initialising all entered data become the default settings Press buttons to scroll through the available options and button to confirm the option Enter the PIN supplied with the telephone card for activating the line TECH 6 E cuoco PIN v TECH gt 6 2 Threshold setting TECH gt 1 FAILURES We returned to the initial menu TECH gt 6 2 Reset counters PRE ALARMS GSM TECH gt 6 From this menu it is possible to send a signal for machine failure through the GSM line if properly installed and activate
37. off and then on again to go into normal operating mode From the filler menu FILL gt 1 press button once to access the program for the TECHNICIAN TECH gt 1 FILL gt 1 Statistics NECTA SPA Manual PROGRAMMING KIKKO 7127 4 TECHNICIAN MENU With the vending machine in normal operating mode press once the programming button located on the inside of the door and the vending machine will be set to FILLER MENU mode from this menu FI LL gt 1 press button and the vending machine will be set to TECHNI CIAN MENU The display will indicate the first available menu TECH gt 1 Failures In this menu it is possible to set all variables regarding machine configuration and control Switch the vending machine off and then on again to exit programming and return to normal operating mode As in the filler menu the selection push buttons have the following functions a V Scrolling keys HER 5 otp to go to the previous the next menu option E _ o PUDOR eee MM eS E Confirm key oF R i to go from a menu to a sub menu or to confirm the s ME information the display MEL ee y i Exit key C os E aaa e to go back from a sub menu to the higher level or to confirm that active data The main menus TECH gt 1 6 and their sub menus are as follows READI NG PRESENT FAI
38. ter the other When confirming the week day with button hour and minutes are displayed which can be changed with buttons 4 or confirmed with button TECH gt 2 1 1 3 Time bands TECH gt 2 1 1 3 1 Set date and time TIME BANDS When confirming with button B the blinking values hour and minute for start and end of time band are entered one after the other If start and end values are set to 00 00 the time v bands are not activated TECH 2 1 1 3 2 Time band 1 4 ay This menu is used to set the type of coin mechanism and its protocol Press buttons to scroll through the menu until finding the type used Available types VALIDATORS Executive MDB BDV when the selected system is displayed confirm with button gt It is possible to operate in the sub menus with the usual procedure In the menu VALIDATORS the value of the 6 validator coin lines A F can be changed In the menu EXECUTIVE it is possible to set one of the following payment systems STANDARD PRICE HOLDING COGES U KEY SIDA The BDV and MDB menus are practically similar The menu TECH gt 2 1 2 1 VENDING TYPE is used to set the operating mode for single or multiple vending With multiple dispensing the change is not returned automatically at the end of dispensing but is made available for the next selections it will be returned only by pressing the change return button The menu TECH gt 2 1 2 1 C
39. them replacing the standard selection STATI STI CS TECH gt 3 Data on the machine operations is stored in both general counters and relative counters which can be reset without losing total data GENERAL DISPLAY TECH gt 3 1 When pressing the confirm button the stored data is sequentially displayed at 1 second intervals and namely 1 counter by single selection 2 counter by time bands 3 discount counter 4 failure counter 5 coin mechanism data GENERAL RESET TECH gt 3 2 Statistics can be reset either globally all types of data or partially for selections discounts overprice failures coin mechanism data Press the confirm button and the message Confirm starts blinking Press the confirm button the message Working is displayed for a few seconds and all statistics are reset RELATI VE DI SPLAY TECH gt 3 3 When pressing the confirm button the stored data is sequentially displayed at 1 second intervals and namely 1 counter by single selection 2 counter by time bands 3 discount counter 4 failure counter 5 coin mechanism data RELATI VE RESET TECH gt 3 4 Statistics can be reset either globally all types of data or partially for selections discounts overprice failures coin mechanism data Press the confirm button and the message Confirm starts blinking Press the confirm button the message Work
Download Pdf Manuals
Related Search