Installation and user manual
Contents
1. gt Control Boxes Are NOT Water Tight lt e Do not power wash Do not hose down Do not use excessive water when cleaning e Clean with soft damp cloth only e CAUTION Excessive water will cause failures 6 Warranty Statement This warranty is void if it is determined that upon inspection by an authorized service agent that the equipment has been modified misused misapplied improperly installed or damaged in transit or by fire flood or act of God Warranty will be considered void if the serial nameplate has been removed or if the unit has been opened or modified in any way or service has been attempted by unauthorized personnel IMPORTANT Keep a copy of your sales receipt to verify date of purchase A valid proof of purchase indicating Serial Number s and date of purchase is required to obtain Warranty Service The prices char ged by CookTek for its products are based upon the limitations in this warranty Seller s obligation under this warranty is limited to the repair of covered defects without charge by a CookTek factory authorized service agent or one of its sub service agencies metos 9 Metos Incogneeto 6 10 2014 7 Trouble Shooting No Power No Lights or Fan Noise ceptacle to make sure that power 1 present Pan Not Centred Buffet Suddenly Stops Heating Possible Power Brown Out Assure proper voltage power Circuit Shared with another Electrical Make sure that the Cook top 1 not sharing2. metos UNDER COUNTER TOP INDUCTION Incogneeto Installation and user manual 27 11 2014 MG4231590 Metos Incogneeto TABLE OF CONTENTS el 1 2 2 1 2 2 ae 2 0 2 3 2 2 5 2 4 2 metos General Information cado 3 MOONT T ee 3 User Interface Buttons 3 Preparing the appliance for use 4 E Pe an 4 WS A dae 4 Electrical installation requirements 4 Mechanical 4 General 5 SON nee Po an ee 6 Me Me N 6 Programming 6 Magneeto Il Operation 607700 MGRFIDOS un aaa 6 o 8 Mpore PEC iii 8 FA INA Eee eat 9 e tats oncogene 9 Magnesto 607700 MORFIDOZ oa 9 Warranty Statements aio 9 To ble SHOOUNG siria 10 Error Gode lala 11 ENS CaN ACION cir 12 Technical specifications 15 6 10 2014 Metos Incogneeto 101 2014 1 General Information 1 1 Model Types MB061 U 120 Volt Model MB062 U 240 Volt Model 1 2 User Interface Buttons Power Button Use this button to turn th
3. on counter top in expected vicinity of unit Ribbed side down Slowly slide the Magneeto around until the red light flashes e Placement where the light flashes brightest is the optimum position e Place dish on top of Magneeto for warming do not cover the RFID tab with the dish Locating may also be performed with the dish already on the Magneto II 6 metos Metos Incogneeto 101 2014 For larger pans Side Top The Magneeto 2 Wireless Com municator mus not be cove red by the disch This will prevent proper communications iL A Fe eee If a large pan must be used then it is OK to cover the red LED but NOT the wireless communicator tab For smaller pans Side Top The pan must be in contact with the Temperature Sensor Over heating the pan can result which may cause terminal damage to the Magneeto 2 If a a small pan must be used then it must be contact with the Temperature Sensor metos 7 Metos Incogneeto 6100204 5 3 Important Information e Never heat an empty pan lt may damage the Buffet or cookware and overheat the unit When over heating occurs an error code will flash on the display and the Buffet will shut itself off automatically When the internal temperature returns to normal the Buffet can be used again e Remember to turn the Buffet off after each use e Keep the Buffet away from gas and electric ranges or open flames Do not place in the o
4. 2 Zero cross failure E 08 Turn unit off then on Plug unit into outlet on different circuit breaker If problem persists service Is required on device 10 Magneeto I RTD Failure E Magneeto I needs repair Service needed tor Magneeto Ensure the RFID tag on the pan Is 11 Tag communication properly located RFID reader falo 19 User interface error E 13 Check control panel connection cycle power Service required red 10 11 16 metos 11 Metos Incogneeto 6100204 9 Installation e Internal cooling fan displaces 70 CFM 2 0m3 min Adequate cabinet venting should be provided typically 16in2 100cm2 per unit The maximum do not exceed ambient temperature is 50 122 e Cooling clearance 6 152mm below e Thickness of stone countertop Thickness of wood substrate Combined thickness of stone wood substrate this measurement should be 30 40mm Rail system conversions 1 18 inches 30mm Match total thickness to 1 26 Inches 32mm closest rail setting and install 1 57 inches 40mm locknuts 444 17 50 468 18 43 UNIT TO UNIT 502 19 76 12 metos Metos Incogneeto 6100204 INSTALLATION FOR 20mm GRANITE GRANITE WITH 20 mm OR 12 mmWOOD SUBSTRATE 1406 _ WOOD SUBSTRATE 16 00 12 mm or 20 mm 406 16 00 SY SCREW DOWN 2 ADJUST BRACKET FOR DESIRED COUNTER TOP THICKNESS 32mm nominal 40mm nominal COUNTER T
5. Configuration MagnaWave Systems POWER ly SmarTag Pan Detect 5 2 General Operation e Press power button to turn the unit on the green LED next to the power button will illu minate e Place a Magneeto on the counter top and position it over top of the unit until the LED begins marlag flashing and the eu Smart lag LED will light up e Place an induction compatible dish on the top of the Magneeto the Pan Detect LED will illuminate make sure the dish is centered on the Magneeto II The unit will start at 80 degrees or the last entered temperature Press up and down arrows to select desired temperature selecting trom the preset choices Fahrenheit Settings 80 190 degrees 80 150 160 165 170 175 180 185 190 Celsius settings 30 85 degrees 30 40 50 60 65 70 75 80 85 e you have chosen your preferred temperature the unit will begin to heat the dish The letter or will flash when the dish Is heating When the dish has reached the set temperature the letter or C will remain solid on the display e lock the controls press lock button three times the red LED to the right of the lock button will illuminate to indicate the unit 1 locked This will prevent temperature settings trom being changed The Power button will continue to function while locked To unlock the controls press the lock button three more t
6. HICKNESS 12 mm WOOD SUBSTRATE 20 mm WOOD SUBSTRATE TO INSTALL UNDER COUNTER hh INSERT BARS PUSH BARS FOWARD IN SLOTS IN TRACK TO ENGAGE THEN SWING UNIT PULL BARS BACK UPWARD 3 TO CLEAR TRACK 2 metos 13 Metos Incogneeto 102014 CookTek Incogneeto Unit Installation Instructions Measure the countertop thickness where the unit will be installed Top of unit must be 38 to 42mm 1 5 to 1 65 from top of counter 20mm Stone Countertop 20mm plywood sheet Unit snaps into lower holes 1 30mm Stone Countertop _ 12mm plywood sheet Unit snaps into lower holes 1 30mm Stone Countertop 20mm plywood strips Unit snaps into UPPER holes If countertop is not prepared as above STOP and correct counterto Installation CookTek 2 Always mount vertically do not mount horizontally Use included screws Don t use alternate hardware Heating O At Temp POWER LOCK e Donot over tighten Do not use lock washers Over Tightening Causes Failures Lock Washer Damage Insert Ethernet cable straight into RJ 45 connector E Strain relieve cable so that connector entry remains straight e Route and protect cable to prevent damage pulling from behind under counter installations storage 14 metos Metos Incogneeto 6100204 10 Technical specifications ler metos 15 metos kitchen intelligence
7. a circuit with other Electrical Devices Safety Shut Off Engaged The Safety Shut Off will engage if an empty pan is left on the Cook top surface while the unit is working at full power Make sure that the Cook top surface clear Wait 15 20 mi nutes for the unit to reset Pan Does Not Get Hot Enough Even Extension Cord In Use Do Not use extension cords Extension Though Power Levels Are Set To Ma cords may affect the power levels reaching ximum Induction Efficient Pan In the appliance Use Circuit Shared with Another Electrical De vice circuit with other Electrical Devices Pan heats Uneveny Does Not man tin Heat Level or Overheats Pan Not Centered C Use a larger Induction Efficient Pan 10 metos Metos Incogneeto 6100204 8 Error Code Table In the event of a Possible Malfunction your CookTek MagnaWave Buffet will display an Error code the alohanumeric display The some models will beep a specific number of times indicated by the error and flash the lights on the control box Please consult the following table when encountering an Error Code To reset error conditions remove the pan from the unit and press unit Power button or unplug the CAE rn Broken Temperature Sensor Over current peak E 03 Try different cookware Service may be required High line voltage E 06 To reset unplug unit wait 5 se conds and plug in again If problem persists have an electrician monitor the line voltage
8. e manufacturer Use unapproved accessories may cause injuries and void the warranty e The pan on the appliance will heat continuously as long as the power is ON The pan will be hot and caution should be exercised when working on or near the appliance e Do not let the power cord touch hot surfaces or hang over the edge of the counter Do not move the appliance when electric power is connected Do not move the appliance while a hot pan or pan con taining hot liquids is on top of the appliance e disconnect appliance press the Power button and wait for LED to no longer be illuminated You may then remove the plug from the outlet e Do not use CookTek Buffet for anything other than its intended use as described in this manual This unit is designed to heat food and 1 not intended for laboratory or industrial use e Do not put food or unopened cans on the Buffet surface e This product may only be serviced by an authorized service agent or by CookTek personnel Do not attempt to open the unit or perform service of any kind For service information contact service e This appliance must be grounded Connect only to a properly grounded outlet Before operating read grounding Instructions and Electrical Installation Requirements on Page 2 of this booklet Do not use an extension cord e Do not overcook food or leave appliance unattended while in use e n the unlikely event of a grease fire smother by covering pan with a t
9. e unit on and off a green LED will indicate when the unit is on Lock Button Use this button to prevent users from adjusting settings Pressing this button three times will lock the unit When the unit 1 locked the only button that will continue to work Is the Power Button To unlock the unit press the lock button three times The red LED to the right of the button will indicate when the unit is locked Up and Down arrows These buttons allow you to quickly set the temperature Alphanumeric display Displays cooking temperature Fahrenheit or Celsius and error code information metos Metos Incogneeto 6 10 2014 2 Preparing the appliance for use 2 1 Before operation AN Before operating your buffet do the following e Remove all packing material and save for subsequent shipment or in case of concealed shipping damage e Keep unit away from other heat sources and allow at least two 2 inches clearance for air circulation at sides front and rear of the unit If either the air intake or exhaust outlet is blocked the internal temperature will rise causing an error code to occur 2 2 Grounding Instructions The buffet must be properly grounded In the event of an electrical short circuit grounding reduces the risk of electric shock by providing a safe path for the electric current The buffet has a power cord with 3 prong grounding plug which must be used in a compatible and properly grounded
10. ight fitting lid cookie sheet or flat tray e DO NOT USE WATER When the fire is under control turn off appliance and unplug from wall e Use only with induction compatible and efficient cookware e Place Buffet on a level hard stable non flammable surface before use 3 metos Metos Incogneeto 6 10 2014 5 5 Care and Cleaning 5 5 1 Incogneeto Buffet Your CookTek Induction Buffet is easy to keep clean Be sure to follow these easy instructions Turn the unit OFF and remove the plug from any power outlets prior to cleaning Never immerse the Buffet in water or put it in the dishwasher 5 5 2 Magneeto 607700 MGRFIDO2 Cleaning When needed clean the Magneeto with mild soap or detergent Care and Cautions The induction unit RFID antenna is located in the back of the unit The Magneeto I RFID tab must be positioned over the antenna Use the Magneeto ONLY with Incogneeto MB061 series 650 watt RFID induction units DO NOT use the Magneeto II with any other induction appliance as it may be damaged Maximum dish pan bottom size is 12 in diameter The dish pan bottom must be flat and in contact with the temperature sensor dome or overheating will result Some upward bowing of the Magneeto when hot and a dish is removed is normal and will disap pear with cooling or when a dish 1 placed on top Do not significantly bend or twist the Magneeto as damage may result
11. imes e When you are finished using the unit press power button the green Power LED will go out Remove the dish from the unit metos 5 Metos Incogneeto 1012014 5 2 1 Change Temperature Scale F C e Starting with the unit off hold down A up arrow while pressing a power on button Then use the down arrow to select the desired scale Powering the unit off completes the selection Note If a button is not pressed for more than five minutes the unit will power off keeping the pre viously set temperature scale 5 2 2 Change Temperature Options Short Long e Starting with the unit off hold down both A and down arrows and press power button Use the arrows to select NUM and press o button Use the arrows again to select PART or for the partial or full set of temperatures Press button to set the value power 5 2 3 Programming a Magneeto e Starting with the unit off hold down Down arrow while pressing o power on but ton e The display will start with the text use this to clear the tag the unit will no longer enter auto mode Otherwise use the up and down arrows to select a temperature Set the tag press Lock Twice The display will read Tag Set e Repeat if necessary with other Magneeto II 5 2 4 Magneeto Il Operation 607700 MGRFIDO2 e With Incogneeto or MB061 unit turned on place Magneeto
12. outlet It is the owner s responsibility to replace any 2 prong wall outlet with a properly grounded 3 prong wall recep tacle For your safety never cut remove or disable the electrical ground connection from the plug Never use an adapter plug or an extension cord with the buffet WARNING Electric shock can result from an improperly grounded plug Please consult a qualified elect rician If you have any questions about these grounding instructions Before you begin Please make sure that this power cord is firmly attached to your CookTek unit BEFORE plugging the unit into the power receptacle and before attempting operation 3 Electrical installation requirements Owner and Installer s responsibility to comply with those codes CookTek is not responsible for any con sequential damages as a result of failure to comply with installation requirements Every installation site has different electrical wiring Because many different local codes exist it is the e Read all installation instructions carefully before starting installation e Remove buffet carefully from carton e Remove all loose packaging and accessories and save for subsequent shipment or in case of led shipping damage e tis the responsibility of the installer to comply with all federal state and local codes e Any installation not matching the specifications discussed in this manual automatically voids the product s warranty 4 Mechanical in
13. stallation e Install the mounting tracks per the installation sheet provided with either the single unit tracks or the rail as appropriate Also see instructions at the end of this manual e Insert the unit with the he Antenna side sticker away from the customer This is the side of the unit that the Magneeto tag must be positioned over e install the unit on the tracks hook one side of the springs on to the track and then compress the other side of the mounting springs and snap it into the track See assembly drawing 4 metos Metos Incogneeto 6 10 2014 5 General Operation Plug the Buffet into a grounded single phase receptacle Models will run on 100 130V drawing up to 650W or on 200 240V drawing a maximum of 650W Check rating plate on unit to verify correct voltage and wattage Voltages below 120V or 240V can result in less than rated power and slower heating times This appliance is designed for holding food products only This unit is equipped with SmarTag technology using RFID to provide precise temperature cont rol The unit requires a Magneeto for operation The Incogneeto unit will not work with a Magneeto module or a RFID equipped chaffing dish NOTE For proper operation an independent dedicated circuit should be used for up to 3 units installed on a 15 amp 120V circuit 4 units installed on a 20 amp circuit 120V or up to 5 units installed on a 20amp 240V circuit 5 1 Control
14. ven If the ambient air temperature is above 110 degrees F the Buffet may not function properly Be sure to dry off the outside of the pan before use Water droplets on the outside of the pan may begin to boil and spatter as the pan temperature rises e Do not use aluminum foil on top of the Buffet e Do not use the Buffet near a faucet swimming pool sink or other areas where water can be found e Never store the Buffet outside or upside down e Do not obstruct block or alter the air entrance or outlet Do not stick foreign objects into these openings e Do not strike or damage the Buffet Do not put the Buffet in your luggage Throwing or dropping the Buffet can damage the internal components or crack the Buffet voiding your Warranty If the Buffet becomes cracked unplug 5 4 Important Safety Precautions e reduce the risk of fire electric shock or injury please read follow and save all instructions e Never immerse cords plugs or appliance in water e Supervise carefully when appliance is used near children Keep children away trom appliance when operation e Always unplug appliance immediately after use and allow for cooling time if handling transporting or storing Do not use any appliance that has a damaged cord or plug or one that has malfunctioned or been damaged Consult the warranty and follow instructions for service e Do not use any accessories or attachments that not recommended by th
Download Pdf Manuals
Related Search