User's Manual - DiscoWorld.dk
Contents
1. Keep the lamp clean Do not touch the lamp glass with bare hand The projector should always be installed with a secondary safety fixing A safety cord is supplied for this it should be attached as shown in installing the projector section The lamp used in this projector is an HMI1200W S discharge lamp After switching off don t attempt to restart the projector until lamp has cooled this will require approx 15 minutes Switching the lamp on and off at short intervals will reduce the life of both the lamp and the projector But occasional breaks will prolong the life of the lamp and projector Never run the projector without a lamp There is no user serviceable parts inside the projector do not open the housing and never operate the projector with the covers removed Always disconnect from the mains when the device is not in use or before cleaning it or before attempting any maintenance work If you have any questions don t hesitate to consult your dealer or manufacturer 3 20 Pilot 1200 manual doc INSTALLING THE PROJECTOR AN WARNING 4 To pass 2 SAFETY CORDS SAFETY CORD through 4 HOLES for safety 2 5 REW CLAMPS 1PCS PER CLAMP 2PCS RETAINERS 2PCS PER CLAMP 4 HOLES FOR SAFETY CORD PASSING THROUGH Take 2 clamps and 2 safety cords out from the package and mount 2 clamps on the underside of fixture with 2 retainers attached to each clamp Hang the fixture on the structure and fasten the2. 8 20 Pilot 1200 manual doc ERRORS DISPLAY In the course of launch PILOT 1200 examines automatically whether there are errors and if there are it will display information as follows INFORMATION ERRORS Er02 Sensor 1 temperature too high 4 Lamp error 05 error 06 Sensor 2 temperature too high 09 Gobo rotation reset error Er10 Gobo change reset error Er11 Effect wheel reset error Er12 Colour wheel reset error Er17 Prism rotation reset error Er18 Prism change reset error Er20 Fixed gobos reset error Er25 Pan motor reset error Er26 Tilt motor reset error REPLACING GOBOS EFFECT WHEEL Be aa y Q gt WA GOBOS RETAINING SPRING Lock Tilt Loosen 2 screws on the rear cover with fans and open the rear cover with fans You could see the structure as shown in the above figure For gobos replacement on the fixed gobo wheel turn the effect wheel and rotated gobo wheel to a proper position first take out a gobo from the fixed gobo wheel carefully fit a new gobo Note if the gobo is a glass one it should be touched with glabrous clean and soft tissue or cloth matted between hand and glass instead of with bare hand For filters replacement on the effect wheel do in the same way of fixed gobo wheel For gobos replacement on the rotated gobo wheel take an appropriate tool to tug the head of retaining spring up and engage yo
3. Care should always be taken when handling these lamps Always read the manufacturers Instructions for use enclosed with the lamp 4 20 Pilot 1200 manual doc POWER SUPPLY MAINS Connect the power cord as follows L live brown E earth yellow green neutral blue Use the plug provided to connect the mains power to the projector paying attention to the voltage and frequency marked on the panel of the projector It is recommended that each projector be supplied separately so that they may be individually switched on and off IMPORTANT It is essential that each projector is correctly earthed and the electrical installation conforms to all relevant standards Power consumption of the PILOT 1200 is 1628W CONTROL CONNECTIONS DMX OUT DMX IN DMX 512 PIN FUNCTION 2 1 1 2 3 DMX OUT wns 5 Connection between controller and projector and between projector and another must be made with a 2 core screened cable with each core having at least a 0 5mm diameter Connection to and from the projector is via cannon 3 pin which are included with the projector or 5 pin XLR plugs and sockets The XLR s are connected as shown in the figure above Note care should be taken to ensure that none of the pins touch the metallic body of the plug or each other The body of the plug is not connected in any way The PILOT 1200 accepts digital control signals in protocol DMX512 1990 Connect the contro
4. Defective projection The lens is broken Dust or grease on lenses Check the lenses are not broken Remove dust or grease from the lenses The projected image appears to have a halo Installation of the lamp is not correct Dust or grease contamination on the optics Make sure the lamp is installed correctly Carefully clean the optical group lenses and the projector components The beam appears dim Dust or grease contamination on the optics The lamp is at the end of its life Check the optics is clean Replace with a new lamp of the specified type and rating LIGHT OUTPUT 25 lux 3800 950 422 237 18 lux 8600 2150 955 537 5m 4m 3m 2 1m 2 18 25 2m im 3m 4m 5m DISTANCE 5m 10m 15m 20m 18 DIAMETER 1 5 31 64 7m 6 3m 25 DIAMETER 0m 2 2m 44 6 6m 8 8 14 20 Pilot 1200 manual doc TECHNICAL DATA VOLTAGES 200 220 230 240V AC 50Hz or 60Hz POWER CONSUMPTION 1628W 230V LAMP Type HTI 1200W S discharge lamp Colour Temperature 6000 K Socket SFc10 4 Manufacturers Rated Lamp Life 750 Hours COLOURS CYM colour mixing system 1 wheel with 7 fixed Dichroic colours plus white With variable speed bidirectional rainbow effect COLOUR TEMPERATURE CORRECTION 2 colour temperature correction filters GOBOS Rotating gobo wheel 4 interchangeable
5. RELIABILITY PILOT 1200 PR 2900 This product manual contains important information about the safe installation and use of this projector Please read and follow these instructions carefully and keep this manual in a safe place for future reference PR LIGHTING LTD No 571 Yingbin Road Dashi Panyu Guangzhou 511430 China http www pr lighting com SAFE USAGE OF THE PROJECTOR 3 INSTALLING THE PROJECTOR 4 FITTING THE LAMP 4 POWER SUPPLY MAINS 5 CONTROL CONNECTIONS 5 DMX TERMINATOR 6 SETUP OPTIONS PROJECTOR CONFIGURATION 6 TO SET THE DMX START ADDRESS 6 FUNCTIONS DISPLAY 7 ERRORS DISPLAY 9 REPLACING GOBOS 9 DMX CONTROL CHANNEL FUNCTIONS 10 LED DISPLAY 12 CHANGING BELTS 12 MAINTENANCE 13 LUBRICATION 13 KEEPING THE PROJECTOR CLEAN 13 TROUBLESHOOTING 13 TECHNICAL DATA 15 ELECTRICAL DIAGRAM 17 COMPONENT ORDER CODES 18 CHANGING THE OPERATION FREQUENCY 19 Please note that as part of our ongoing commitment to continuous product development specifications are subject to change without notice Whilst every care is taken in the preparation of this manual we reserve the right to change specifications in the course of product improvement The publishers cannot be held responsible for the accuracy of the information herein or any consequence arising from them Every unit is tested completely and packed properly by the manufacturer Please make sure the packing and or the unit are in good condition before installation and use
6. KEEPING THE PROJECTOR CLEAN To ensure the reliability of the projector it should be kept clean It is recommended that the fans should be cleaned every 15 days The lens and dichroic colour filters should also be regularly cleaned to maintain an optimum light output Do NOT use any type of solvent on dichroic colour filters Cleaning frequency depends on the environment in which the fixture operates damp smoke or particularly dirty surroundings can cause greater accumulation of dirt on the unit s optics A soft cloth and typical glass cleaning products should be used in cleaning It is recommended to clean the external optics at least once every 20 days and clean the internal optics at least once every 30 60 days Do not use any organic solvent e g alcohol to clean the reflector mirror dichroic colour filters or housing of the apparatus 13 20 Pilot 1200 manual doc TROUBLESHOOTING PROBLEM POSSIBLE CAUSE ACTION The projector doesn t switch on The power supply is not present The lamp doesn t work Check the fuse on the power Socket Replace the lamp The lamp comes on but the projector doesn t respond to the controller Wrong DMX configuration and or start address Defective DMX cable Make sure that the projector is correctly configurated Replace or repair the DMX cable The projector only functions intermittently The fan has failed Make sure the fan is working and not dirty
7. Panyu Guangzhou China Post Code 511430 TEL 86 20 8478 1888 FAX 86 20 8478 6023 P N 321010221 Last Revision 10 08 2004 20 20 Pilot 1200 manual doc
8. Should there be any damage caused by transportation consult your dealer and do not use the unit Any damage caused by improper use will not be assumed by the manufacturer and or dealer ACCESSORIES THESE ITEMS ARE PACKED TOGETHER WITH THE PROJECTOR G clamps 2 PCS XLR cable with 3 pin plug and socket 1 PCS Safety cord 2 PCS Spare gobos 4 PCS This manual 1 PCS Q clamps Options 2PCS INTRODUCTION Thank you for purchasing our product PILOT 1200 PR 2900 This product manual contains important information about the safe installation and use of this projector Please read and follow these instructions carefully and keep this manual in a safe place for future reference PILOT 1200 is an innovative projector with an elegant housing which complies to CE norms and standards and uses international protocol DMX 512 The projector uses HMI1200W S discharge lamp and high quality optical system which produces bright and beautiful light beam and has 60 output lumen more than the similar products with the same power consumption The projector features effects of strobe frost light mixed colours and rainbow so it is suitable for applications in TV station disc singing and dancing stage nightclub etc 2 20 Pilot 1200 manual doc SAFE USAGE OF THE PROJECTOR When unpacking and before disposing of the carton check there is no transportation damage before using the projector Should there be any damage caused by transportation
9. consult your dealer and do not use the apparatus The projector is for indoor use only IP20 Use only in dry locations Keep this device away from rain and moisture excessive heat humidity and dust Do not allow contact with water or any other liquids The projector is not designed or intended to be mounted directly on to inflammable surfaces The projector is only intended for installation operation and maintenance by qualified personnel The projector must be installed in a location with adequate ventilation at least 50cm from adjacent wall surfaces Be sure that no ventilation slots are blocked Do not project the beam onto inflammable surfaces minimum distance is 5m 9 5m Avoid direct exposure to the light from the lamp The light is harmful to the eye Do not attempt to dismantle and or modify the projector in any way Electrical connection must only be carried out by qualified personnel Before installation ensure that the voltage and frequency of power supply match the power requirements of the projector It is essential that each projector is correctly earthed and that electrical installation conforms to all relevant standards Do not connect this device to any other types of dimmer apparatus Make sure that the power cord is never crimped or damaged by sharp edges Never let the power cord come into contact with other cables Only handle the power cord by the plug Never pull out the plug by tugging the power cord
10. gobos white indexable bidirectionally rotating at variable speeds Fixed gobo wheel 4 interchangeable gobos white the fixed gobo wheel can scroll in eather direction at variable speeds Both glass gobos and metal gobos may be fitted to either wheel Gobo diameter 51 8mm Gobo image diameter 048mm PRISM 1x2 facet 1 x 3 facet 1x5 facet 1 x linear prisms indexable bidirectionally rotating at variable speeds FOCUS DMX controlled focus EFFECT FILTERS 1 ultraviolet filter and 1 bicolour filter FROST Variable frost effect 0 100 linearly adjustable SHUTTER Double shutter blades 0 100 linearly adjustable STROBE 1 5 HEAD MOVEMENT Pan 540 Tilt 270 BEAM ANGLE 189 25 linear zoom CONTROL DMX512 20 channels plus 2 channels for high resolution Pan and Tilt 15 20 Pilot 1200 manual doc OTHER FUNCTIONS Adjustable Pan amp Tilt speed Projector usage time display lamp time display HOUSING Metal and composite plastic IP20 WEIGHT 5AKg SIZES See Drawings 16 20 Pilot 1200 manual doc lt lt a lt O AOLE_ANOL RB A04 3704 2 dvo V dvo ZH0S A D NI q GOONS 171 SIM00ZLINH gt NMOG L NV4 NMOG Sd MS lelsouueul MOS 91 pilos AO 22 002 Jeuuojsue EE 4 401 t Nv
11. parts of the PILOT 1200 besides the table listed above When ordering please state the exact name and part no Repairs must be carried out by a qualified technician 18 20 Pilot 1200 manual doc CHANGING THE OPERATION VOLTAGE AND OR FREQUENCY To be carried out by qualified engineers only The power input setting of the PILOT 1200 may be changed to suit the supply in your area that the unit is to be operated The voltage and frequency are pre set at the factory and marked on the exterior of the unit Any error or mistake in setting the voltage or frequency of the projector may seriously damage the unit Make sure the specifications of the transformer match the power supply and if not the suitable transformer must be ordered see the data It is strongly recommended that you immediately mark the new frequency on the projector so that it may not be mistaken for the factory set frequency To change the frequency Open the base of the projector by unscrewing the eight screws on the top of the base and do the following operation Locate the ballast in the base of the projector and select the required frequency from 50Hz or 60Hz by moving the cable to the appropriate position The ballast will be labeled to show the connections Never move or disconnect the cable attached to the connector marked L Once finished with the settings re assemble covers 19 20 Pilot 1200 manual doc PR LIGHTING LTD No 571 Yingbin Road Dashi
12. 39 Reverse rotation speed 3 240 247 Reverse rotation speed 2 248 255 Reverse rotation speed 1 fastest Nm 000 255 Cyan 0 100 m n 000 255 Yellow 0 100 PIE bene 000 255 Magenta 0 100 000 050 White 13 102 157 Gobo obo Rotating Gobo 153 203 Gobo 3 204 255 Gobo 4 000 119 Gobo index 0 540 120 127 Rotation speed 1 fastest 128 135 Rotation speed 2 136 143 Rotation speed 3 144 151 Rotation speed 4 152 159 Rotation speed 5 160 167 Rotation speed 6 168 175 Rotation speed 7 14 176 183 Rotation speed 8 slowest Gobo Rotation 184 191 Stop rotating 192 199 Reverse rotation speed 8 slowest 200 207 Reverse rotation speed 7 208 215 Reverse rotation speed 6 216 223 Reverse rotation speed 5 224 231 Reverse rotation speed 4 232 239 Reverse rotation speed 3 240 247 Reverse rotation speed 2 248 255 Reverse rotation speed 1 fastest 000 050 White 15 051 101 Prism 1 Prism 102 152 Prism 2 153 203 Prism 3 204 255 Prism 4 16 000 119 Index 0 540 Prism Rotation 120 127 Rotation speed 1 fastest 128 135 Rotation speed 2 136 143 Rotation speed 3 11 20 Pilot 1200 manual doc 144 151 Rotation speed 4 152 159 Rotation speed 5 160 167 Rotation speed 6 168 175 Rotation speed 7 176 183 Rotation speed 8 slowest 184 191 Stop rotating 192 199 Reverse rotation speed 8 slowest 200 207 Reverse rotation speed 7 208 215 Reverse rotation s
13. VDC KD2406PTS1 in strobe SUNNO 030069005 DC24V2 6W 4 5 on the rear cover 030060039 CIC 100 5 1 FAN6 7 in base SUNNO 030060035 KDE2409PTB 6 24VDC MOTORS MOTOR 1 2 PAN 030040089 23HS2039L MOTOR 34 TILT 030040068 23HS0001 07L MOTOR 5 6 SHUTTER BLADE 030040084 17HS0002 59L MOTOR 7 PRISM 030040085 17HS0002 61L MOTOR 8 PRISM 030060099 MOTOR 9 PRISM ROTATION 030040085 17HS0002 61L MOTOR 10 FIXED GOBO WHEE 030060098 MOTOR 11 COLOUR WHEEL 030040084 17HS0002 59L MOTOR 12 ROTATING GOBO WHEEL 030040098 MOTOR 13 GOBO ROTATION 030040084 17HS0002 59L MOTOR 14 FOCUS 030040083 17HS0002 60L MOTOR 15 EFFECT WHEEL 030040083 17HS0002 60L MOTOR 16 17 ZOOM 030040083 17HS0002 60L MOTOR 18 19 FROST 030040060 16 0002 021 MOTOR 20 21 CYM YELLOW 030040061 16HY0002 03L MOTOR 22 23 CYM CYAN 030040061 16HY0002 03L MOTOR 24 25 CYM MAGENTA 030040060 16HY0002 02L CHIPS IC1 2 3 NJM3771D2 sli PBL3771 170110004 C4 5 6 7 NJM3772D2 170110019 IC8 MB88346B 170170056 IC9 CM2576 5V oles IC10 MAIN CPU 230040161 IC11 MINOR CPU 230040162 1212 13 14 15 16 17 NJM3771D2 s PBL3771 170110004 18 LM2574N 5 170170039 Motordriver I IC19 MB88346B 170170056 Motor driver II IC20 CPU 230040163 IC21 CPU 230040159 IC22 MCP100 450 170040035 1223 DS75176BN 3X SN75176BP 170170012 iS 24 24LC256 170170058 NOTE You may order all
14. ddOl NVvddOl cNVddOl 5082 LJ LJ UJ LJ UJ LJ UJ 5 E d E S LJ UJ LJ LJ LJ GJ JOjoW Jepoous ON Jojo epooue ON joo W epoou3 09 8 V CNVd V NVd lt lt L T W WAO AWAD TIVH NVd TWH LLL L AS 8viva x W 10 O809 XI4 99 2 WSlHd LJ LJ UJ EER qi LI LI snoo4 X07109 103443 0809 O80910nu a a WsSlHd LONN Pilot 1200 manual doc 17 20 COMPONENT ORDER CODES NAME PART NO REMARK 040030054 200 240V EN 040030056 220 230V THERMOSTAT 190010035 KSD020 120 15A 250V CAPACITOR 140010043 TOpgF 370V BALLAST 040070059 230V 50 60Hz 575W IGNITOR 040090036 575 1200W 6 8KV LAMP 100050013 HMI 1200W S PAN amp TILT DRIVE 2 3 290151221 HTD459 3M 6 Belt 290151302 100 311 FANS KDE2408PTB1 6 FAN1 2 in strobe SUNNO 030060031 24
15. everse rotation speed 2 240 247 Reverse rotation speed 3 248 255 Reverse rotation speed 4 fastest 2 000 255 Pan rotation Pan T 000 255 Tilt rotation 000 255 Linearly focusing E 000 255 Zooming with spot from large to small 9 000 024 White Note stay 5 seconds while DMX value is 5 6 Colour Wheel or 7 the function reset perform 025 030 White colour filter 1 031 036 Colour filter 1 037 042 Colour filter 1 colour filter 2 043 048 Colour filter 2 049 054 Colour filter 2 colour filter 3 055 060 Colour filter 3 061 065 Colour filter 3 colour filter 4 066 071 Colour filter 4 072 077 Colour filter 4 colour filter 5 10 20 Pilot 1200 manual doc 078 083 Colour filter 5 084 089 Colour filter 5 colour filter 6 090 095 Colour filter 6 096 101 Colour filter 6 colour filter 7 102 107 Colour filter 7 108 113 Colour filter 7 white 114 121 Rotation speed 1 fastest 122 129 Rotation speed 2 130 137 Rotation speed 3 138 145 Rotation speed 4 146 153 Rotation speed 5 154 161 Rotation speed 6 162 169 Rotation speed 7 170 177 Rotation speed 8 slowest 178 191 Stop rotating 192 199 Reverse rotation speed 8 slowest 200 207 Reverse rotation speed 7 208 215 Reverse rotation speed 6 216 223 Reverse rotation speed 5 224 231 Reverse rotation speed 4 232 2
16. ller s output to the first fixture s input and connect the first fixture s output to the second fixture s input and connect the rest fixtures in the same way Eventually connect the last fixture s output to a DMX terminator as shown in the figure below DMX IN FROM TERMINATOR CONTROLLER 5 20 Pilot 1200 manual doc DMX TERMINATOR In the Controller mode at the last fixture in the chain the DMX output has to be connected with a DMX terminator This prevents electrical noise from disturbing and corrupting the DMX control signals The DMX terminator is simply an XLR connector with 1200 ohm resistor connected across pins 2 and 3 which is then plugged into the output socket on the last projector in the chain The connections are illustrated below 2 lt 1 DMX TERMINATOR CONNECTION Connect 1200 OHM resistor across gt lt pins 2 and 3 in an XLR plug and insert 3 into the DMX OUT socket on the last MS 1200 unit in the chain PIN 2 PIN 3 SETUP OPTIONS PROJECTOR CONFIGURATION EHBH e 2 e FUNC DOWN UP ENTER Projector configuration can be set conveniently via pressbutton switch and digital display Turn the projector on and the digital display will show DMX address you set and save last time and it can be reset and saved again as you please Press button UP or DOWN if you want to browse through the various Setup Options Press button ENTERI to save your settings or enter the next menu Press button or DOWN
17. normally indicate that it is reaching the end of its life and it should be changed at once aged lamps run to the extremity of their life might explode If the projector does not function check the fuses on the power socket of the projector they should only be replaced by fuses of the same specification 6 35X32 T15A 250V On the PCBs inside the projector there are also 3 fuses They are 2 fuses 6 3A 250V fast blow 5mmx20mm on both Pan PCB and Tilt PCB 1 fuse 4A 250V fast blow 5mmx20mm on driver PCB Should these be damaged call a qualified technician before replacement The projector has thermal protection device that will switch off the projector in case of overheating should either of these operate check that the fans are not blocked and if they are dirty clean them before switching on the projector again Check that the fans are operational if not call a qualified technician Any maintenance work should only be carried out by qualified technicians LUBRICATION To ensure the continuous rotation of the rotating gobos and linear motion of the lens for focusing it is recommended that the bearings for the rotating gobos and the 2 shafts for the focusing lens holder be lubricated periodically preferably every two months Use only high quality high temperature resistant grease instead of any type of oil When lubricating the bearings a syringe with a fine needle is the easiest way to introduce the grease to the bearings around each gobo
18. peed 6 216 223 Reverse rotation speed 5 224 231 Reverse rotation speed 4 232 239 Reverse rotation speed 3 240 247 Reverse rotation speed 2 248 255 Reverse rotation speed 1 fastest 000 050 White 7 02452 Efect ec 153 203 Effect 3 204 255 Effect 4 E 000 255 Frosting from slight to strong 010094 rost Pan amp Speed 000 255 Pan amp Tilt speed adjustable by steps from fast to slow MEN 000 255 Pan rotation in 16 Bit precision NN 000 255 Tilt rotation in 16 Bit precision 22 000 170 Lamp ON Reserved Control 171 255 Lamp OFF after 10 seconds or over Reserved LED DISPLAY Green ON DMX signal OK or Slave OFF No DMX signal Flash DMX error Red Medium flash Menu mode Fast flash software cpu error Both ON Address mode Flash in turn Master mode CHANGING BELTS Pan s belts Free 2 screws on Pan assembly s maintenance door and open the door change the belts close the door and fasten the screws Tilt s belts The common users replacing the belts is not recommended L ur x Pan assembly s maintenace door Open the door 12 20 Pilot 1200 manual doc MAINTENANCE If the projectors lens becomes damaged or broken it should be replaced If the lamp becomes damaged or deformed in any way it must be replaced If the light from the lamp appears dim this would
19. roller The PILOT 1200 has 22 channels so set the No 1 projector s address 001 No 2 projector s address 023 No 3 projector s address 045 No 4 projector s address 067 and so on Launch the projector Press button FUNC to Addr press button ENTER it will display 100 I press button UP and DOWN you can set the address press button ENTER to confirm 6 20 Pilot 1200 manual doc FUNCTIONS DISPLAY 1 DISPLAY ADDR Alc cl SET ADDR ADDR 001 LF PAN ANTI CLOCKWISE ROTATION SWITCH oHm F mb TILT ANTI CLOCKWISE ROTATION SWITCH 16 BIT PRECISION SWITCH HERE CODER SWITCH PHOTOCOUPLER POSITIONING n ON L FL COLOUR FILTER LINEAR SWITCH OFF LH n Li FIXED WHEEL LINEAR SWITCH orr ON L ANF swircH RESERVED ON GF E RESERVED orr ON 11 SLAVE IN MASTER SLAVE MODE RESERVED orr ON m BE MASTER MODE 1 RESERVED ON CONTINUE 7 20 Pilot 1200 manual doc rik 2 MASTER MODE 2 RESERVED orr 5 E MASTER MODE 3 RESERVED HFEF ON m 5 E H MASTER MODE 4 RESERVED HFF H DISPLAY TIME HOUR HDD 69 H001 MEANS 1 HOUR
20. screws attached to each clamp Watch the WARNING on the underside of the base as shown above To ass 2 SAFETY CORDS through 4 HOLES for safety Always ensure that the projector is firmly anchored to avoid vibration and slipping whilst functioning Always ensure that the structure that you are going to mount the projector is secure and is strong enough to support a weight of PILOT 1200 WARNING 1 Unlock the PAN and TILT before the 1 application of projector for safety 2 The projector MUST be lifted or carried by the HANDLES instead of clamps FITTING THE LAMP BULB PST TILT LOCK NUTS Lock tilt before fitting replacing the lamp Loosen 2 5 screws and open one of the rear covers you can see the structure as shown in the figure above Loosen 2 nuts at the both ends of lamp and take out the worn out lamp Suggest to free one end after another Fit new lamp and fasten 2 nuts at the both ends of lamp Notes don t touch the bulb of the new lamp with bare hand so as not to influence the beam output the PST pumping stem tip off on the bulb facing the rear cover with fans perpendicularly and being not in the beam s way is a must and aids cooling Close the rear cover and fasten 2 M5 screws WARNING The HMI series are high pressure lamps with external igniters 4
21. to shift the display between Lin and or change the display of address Press button it will return to the upper menu one by one The display will return automatically to the function of address display if you stay for about 60 seconds defaulted E g if you want to set the function of Pan Tilt 16bit precision valid do as follows launch the apparatus press button FUNC to Addr which is displayed in digital display press button to UPEn press button ENTER it will display i nuP press button UP consecutively to Hr press button ENTER it will display press button to Un in the end press button ENTER Well done you have validated this function now If you want to set the function of Pan Tilt 16bit precision invalid press button DOWN to Then press button ENTER to invalidate this function And if you want to set another function valid or not press button FUNC to track back one by then do the same way of e g above TO SET THE DMX START ADDRESS Each PILOT 1200 must be given a DMX start address so that the correct projector responds to the correct control signals This DMX start address is the channel number from which the projector starts to listen to the digital control information being sent out from the cont
22. ur another hand to take the retaining spring out take the gobo out fit new gobo and fit the retaining spring Notes the gobo cannot be touched with bare hand never attempt to dismantle the gobo holder on which you want to replace the gobo be careful of the gobo when the replacement is underway and don t drop it Close the rear cover and fasten 2 M5 screws 9 20 Pilot 1200 manual doc DMX CONTROL CHANNEL FUNCTIONS The PILOT 1200 uses 22 DMX channels They are listed in the following table CHANNEL DMX DESCRIPTION 000 009 Shuttering 010 024 White 025 039 Strobe 1 040 054 Strobe 2 055 069 Strobe 3 070 084 Strobe 4 085 099 Strobe 5 100 114 Strobe 6 1 115 129 Strobe 7 130 144 Strobe 8 145 159 Strobe 9 160 174 Strobe 10 175 189 Strobe 11 190 204 Strobe 12 205 219 Strobe 13 220 234 Strobe 14 235 249 Strobe 15 250 255 White 2 000 009 Black Dimmer 010 024 Open 025 255 Dimming from light to dark 0 100 3 Linearly adjust iris from large to small O wholly Iris eem open 100 wholly closed 000 031 White 032 063 Gobo 1 064 095 Gobo 2 096 127 Gobo 3 128 159 Gobo 4 4 160 167 Rotation speed 1 slowest Fixed Gobo 168 175 Rotation speed 2 176 183 Rotation speed 3 184 191 Rotation speed 4 fastest 192 223 Stop rotating 224 231 Reverse rotation speed 1 slowest 232 239 R
Download Pdf Manuals
Related Search