HDMI Extender Matrix User Manual
Contents
1. and connection Q5 Video is stuck and unstable A5 Check if TX to LAN switch and LAN switch to RX network cable are too long Q6 Network matrix can not output image normally A6 1 Check if TX and RX IP MAC address are repeated 2 Check if Lan switch IGMP function is enabled Q7 Multiple RXs receive same IGMP source RXs can not output audio synchronously A7 Restart Lan switch or IGMP source TX to make all RXs receive signal synchronously Q8 Have already modified IP address and need to modify again but forget the modified IP address and unable to enter into products network management page Press the system reset button for 5s the small hole beside of HDMI port and can restore IP and MAC to default factory setting 8 SPECIFICATION Power supply DC5V 1A Supportinput 480i 60HZ 480p 60HZ 576i 50Hz 576p 50Hz resolution 720p 50 60Hz 1080i 50 60HzZ 1080p 50 60Hz Support output 480p 60HZ 576p 50Hz 720p 50 60Hz resolution 1080p 50 60HZz Network cable UPT STP cat5e 6 Network cable length between all connections Lanewiien Support network management function and IGMP IGMP snooping Support lacal area network bandwidth gt 100M Audio format supported PCM Audiosample Ii 44 1kHz 48kHz po Video compression M JPEG format Send SW LxWxH 13x8 5x2 4 cm nanutfacturel2. information page A http 192 168 168 56 Dies as KF RSE BBV CA IAT MAH IP address 192 168 168 56 Subnet Mask 255 255 255 0 MAC address 00 0b 78 00 60 02 _ In this control page users can change IP address and MAC address only And please note all the RX and TX in the same network matrix must be in the same network segment the IP and MAC addresses for these RX and TX must be different 4 The TX MAC address 00 0b 78 00 60 01 and RX MAC address 00 0b 78 00 60 02 are defaulted by system And MAC address is the identifier for every site of internet it is 6 bytes RA the registration administration of IEEE assigns the first three bytes to different factories the last three bytes are assigned by users MAC address is consist of figures O 9 and letters a f We do not suggest that users change the first three bytes the last three bytes can be changed accordingly 7 RFQ Q1 TV is black screen and OSD displays searching TX on top left corner A1 Check TX LAN switch and network cable connection and make sure all of them are powered on Q2 TV is black screen and OSD displays IP xxx xxx xxx is not my group A2 Check if the RX and TX display the same IGMP group value Q3 TV is black screen and OSD displays Check TX s input signal A3 Check if the TX has HDMI signal input Change HDMI cable to retest Q4 The Lan port yellow indicate led does not light A4 Check the network cable quality
3. HDMI Extender Matrix User Manual This product delivers reliable HDMI transmission over single cat5 6cable and enable matrix extender function through Lan switch which supports IGMP It supports TCP IP Easy and simple to build video network matrix and it is with good stability and anti interference capability Widely applied in the fileds requiring full HD such as advertising business product show CCTV field etc 1 IMPORTANT SAFETY INSTRUCTIONS 1 Do not mix up transmitter TX and receiver RX before installation 2 Do not plug and unplug IR receiver extension cable with power on Use DC5V power supply only Please make sure specification matched if using 3 adapters not supplied by us 2 PACKAGE CONTENTS E gt HDMI to Lan sender TX Lan to HDMI receiver RX DC5V1A 2pcs QO chabneL Remote Control IR receiver extension cable User Manual 3 INSTALLATION REQUIREMENTS 3 1 HDMI source device computer graphics card DVD PS3 HD monitoring equipment etc 2 Display or projector with HDMI port 3 Lan switch with IGMP or IGMP snooping function 4 UTP STP cat5e 6 cable 5 Network cable length requirement between switch and TX RX cascade CAT5 lt 80m CAT5E lt 100m CAT6 lt 120m 3 3 3 3 4 INSTALLATION PROCEDURES 4 1 Assembly cat5e 6 network cable Follow the stanard of IEEE 568B 1 Orange white 2 Orange 3 Green white 4 Blue 5 Blue white 6 Green 7 Brown white 8 Brown 4 2 Set IP and MAC address of TX and RX pl
4. ease refer to 5 1 to change 4 3 Check if IGMP function of LAN switch is enabled IGMP IGMP snooping is enabled through LAN switch network management Please make sure the switch support IGMP IGMP snooping function when purchasing it The LAN switch network management setting is differnent from different manufacturers Contact your LAN switch supplier to consult how to enable IGMP function 4 4 Connections 1 Connection between ports INPUT Ge HDMI HDMI input Power input IR receiver o OUTPUT DC 5V HDMI output Power input IR receiver I IO 5V 1A HDMI display 2 Connection via LAN switch DVD I a A gt p TX 4 RX TV Ee 5 IGMP group chosen and Nixie tube display instruction 5 1 Button usage instruction Short press Press to set IGMP group and display the setted value Product switches automatically to the corresponding IGMP group 5 seconds after the press Long press Press and keep 3 seconds to reset the product only for software It will not restore system specification to factory setting IR Control The input signal channel can be switched by remote control 5 2 Nixie tube display instruction When RX and TX display the same value it builds corresponding IGMP group RX will output the same A V signal with the matched TX One TX can support 16 ways source signals at the most 6 IP and MAC address setting System module has equipped HTTP server It can change s
5. ystem IP and MAC address via webpage Before building network matrix the IP and MAC address of TX and RX must be reset The principle is that all the RX and TX in the same network matrix must be in the same network segment the IP and MAC addresses for these RX and TX must be different TX and RX have a default IP address TX is 192 168 168 55 RX is 192 168 168 56 After the change press the system reset button for 5 seconds the small hole beside of HDMI port to restore IP and MAC to default factory setting Setting procedure as below 1 Set PC s IP network segment the same with TX RX s IP segment like 192 168 168 100 Take win7 for example Internet Protocol Version 4 TCP IPv4 Properties 2 x General N You can get IP settings assigned automaticaly if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings C Obtain an IP address automatically Use the following IP address IP address Subnet mask Default gateway i SJ S ij c oJ Css g J J Re Use the following DNS server addresses Preferred DNS server Alternate DNS server Ce ee 2 Connect PC net port with TX or RX net port directly Power the system to connect PC and TX or RX through 3 Input TX 192 168 168 55 or RX 192 168 168 56 IP address to IE address bar and enter into control page Click system on the page left menu bar then can chang IP and MAC address in switch
Download Pdf Manuals
Related Search