User Manual ›› - Energi
Contents
1. User Manual gt gt Copyright Copyright 2012 Guangzhou HYENERGY Technology Co Ltd All rights reserved Trademarks All product font and company names mentioned in this manual may be trademarks or registered trademarks of their respective companies HYGCI 15CL User Manual Page 1 of 31 Chapter Overview About this Manual General Information Safety Instructions Description of the Device Installation Initial Operation Operation at the Device Appendix HYGCI I5CL User Manual Page 2 of 31 About this Manual 1 About this Manual This chapter explains symbols signal words and abbreviations possibly used in this manual 1 1 Illustration of General Notices Beside warnings general notices are used in this manual to emphasize information These notices are labeled by the following symbols Symbols for General Notices OO em Dn Tipfor background inform ation 1 2 Abbreviations BDEW German Association of Water and Energy Industries German Bundesverband der Energie und Wasserwirtschaft BGV Regulations of the German professional association concerning the prevention of accidents German Berufs genossen schaftliche Verordnung CE Labeling of the Communaut Europ enne European Community confirms the conformity of products with the relevant EU standards and guidelines DIN German Institute for Standards German Deutsches Institutf r Normung DNO Distribution Network Operato2. V1 0 V1 5 display integrated in the front panel of the device displays the different measured variables Thus you can check the performance of the small wind turbine The data logger stores the values for later use The operating mode of the device is indicated by the LED status display The HYGCI 15CL V1 0 V1 5 meets the applying European regulations and standards Among others the device complies with the BDEW guideline for the connection and parallel operation of generators in the public low voltage grid of the distribution network operators DNO This includes the regulations for mains monitoring according to DIN V VDE V 0126 1 1 automatic disconnection device between a generator and the public low voltage grid You can look up other country configurations and standards in the Internet Country specific and plant specific settings are secured by password and must be set by the plant manufacturer of the WT 2 1 Scope of Supply and Additional Equipment The following articles are included in the scope of supply when you purchase the HYGCI 15CL V1 0 V1 5 lt HYGCI 15CL V1 0 V1 5 lt Wall mount with suitable bolts and fixings lt User Manual HYGCI 15CL User Manual Page 4 of 31 Safety Instructions 3 Safety Instructions ZS These safety instructions must be kept 3 1 General Safety Instructions gt Before installation please read all instructions in this manual gt Itis performed only by qualified personnel
3. gt All electrical installation shall be done in accordance with local and national electrical codes gt Connecting to the grid must be done after receiving prior approval from the utility company gt Before connecting please shut down the generator output in order not to get electric shock for the generator will generate electricity in the wind All Information and advice attached to the device such as safety instructions or danger warnings and technical data type plate are gt not to be removed gt not to be damaged gt tobe kept readably no covers no paint over or the like 3 2 Appropriate Use The appropriate use involves gt completely reading and following the content of the documentation and attend to the safety instructions and danger warnings comprised therein gt mounting and connecting the device according to the installation instructions by trained staff Moreover we refer to the following guidelines gt regulations of the utility concerning the grid feed in gt instructions of the small wind turbine manufacturer HYE is not liable for damage resulting from unintended use of the device 3 3 Galvanic Isolation The HYGCI 15CL V1 0 V1 5 is constructed and designed to assure maximum safety during the installation and operation The maximum possible degree of safety is being assured by the galvanic isolation of the input and the output In addition the galvanic isolation allows parallel connection
4. Device This chapter describes the different displays and settings you can attain via the operating unit of the device You find a clearly arranged operating structure attached ic 7 1 Introduction on the inverter panel e e re A v T Fig 11 Operating unit of HYGCI 15CL A LEDs B LCD Display C Buttons State eooe Off Standby state Flash Connecting to The Grid On Connected to The Grid On Generating Power to The Grid Off An Error Occurred Off Manual Stop State UP Up to another screen 2 To increase the value 1 Down to another screen Down a 2 Shift to the next edit position Both press for0 5 1s Applying the current input or switch Enter to the next screen Both press for 1 2s Cancel the current input screen is Esc set back to the previous one Both long press Switch to the main menu Esc HYGCI 15CL User Manual Page 17 of 31 Operation at the Device 1 Checking the wiring of controller and inverter correct or not Please refer to 5 2 wiring diagram 2 Open inverter AC grid switch 3 After inverter starting inverter goes into Initializing status and starts to check if grid voltage and frequency meet setting standard of inverter In the initializing process All of the LEDs are on If the grid is abnormal the ERR light will be on 4 Grid voltage and frequency is normal by inverter initial check after 30 seconds inverter starts to work then all LEDs are off and LCD sc
5. RETR HE SSE TO EVES TSS PACS FRE DI SESE T SL EE FTES I 4 1 1 Output of a HYGCI 15CL V1 0 V1 5 The following figure indicates the relation between the generated DC voltage and the maximum output power Power Curve 120 100 80 pmax k Q oO ZX X 20 P E 0 O 40 160 450 Fig 2 Output curve HYGCI 1I5CL User Manual Page 9 of 31 Description of the Device 4 2 Device View and Type Plate GRID TIE INVERTER Serial No FCTW1KS13100001 Model No v1 0 0O V1 5 D 190VAC 40 200VAC 240VAC 600 700VA FACnom 50HZ 47 5HZ 51 5HZ A LL 1000W PACmax 1100W 1600W Gnd C t VDE0126 1 1 CE P20 X Caution Risk of electric shockfrom energy stored in capacitiors Don t touch live parts until 1 Omil after disconnection the source of supply Fig 3 HYGCI 15CL V1 0 V1 5 steel sheet housing with type plate A Operating unit with graphic display LEDs and push buttons B Steel sheet housing IP Code IP20 C Screwed cable glands D Manual brake E Manual brake caution mark F Type plate HYGCI 1I5CL User Manual Page 10 of 31 Description of the Device 4 3 Dimensions Grid Tied Inverter For Wind Turbines Onduleur olien pour connexion r seau 420mm m Fig 4 Dimensions HYGCI 15CL V1 0 V1 5 steel sheet housing in mm Fig 5 Dimensions wall mount in mm HYGCI I5CL User Manual Page 11 of 31 9 5 1 3 1 1 Installation Ins
6. method There is a RS485 RS232 converter optional between PC and RS485 bus Communication system diagrams are as below HYE Grid Tied inverter For Wind Turbines Ortuleut balea pou Commenion feseau EE g RS485 252 RE PEC RS232 HHO JaRa 2102D Fig 9 Communication Connection of HYGCI 15CL V1 0 V1 5 and RS485 RS232 converter optional i The HYGCI 15CL V1 0 V1 5 is to be connected according to the figure ae By means of the disconnecting points 2 breakers the device is de energized to ensure that you can work safely at the device and personal injuries are avoided in the event of an error 5 2 1 Opening the Device SE Opening the device will result in the loss of warranty HYGCI 15CL User Manual Page 15 of 31 Initial Operation 6 Initial Operation Take the following steps to put the HYGCI 15CL V1 0 V1 5 into operation A According to installing process connect the turbine controller inverter and grid B Before starting ensure AC voltage to meet the start conditions C Switch on the circuit breaker to connect the grid D Switch off the manual brake E When all start conditions are met the inverter will automatically start to generate power to the grid F In normal operation of inverter it needs no people to control as well as it will automatically restart after an error stop HYGCI 1I5CL User Manual Page 16 of 31 Operation at the Device 7 Operation at the
7. 1 A1 2011above 50 2Hz B Make sure that connecting wires can support over current C For safe installation and operation the breaker is necessary which should support over current and over voltage D Technical specification and standard should be in accordance with local power company code gt Input three phase AC connection A Please make sure the wind turbine is stop during installation To ensure the safety while installing the system please switch the manual brake to ON status Since the manual brake switch is ON wind turbine can keep stop during your installation During the operation in the future when storm is coming you can stop the turbine by turning on manual brake located right side down of the inverter Please refer to following cable connection ra WIND TURBINE yy HYGCI 15CL User Manual Page 14 of 31 Installation Three phase AC output wires from turbines connect to three phase input ports Please ensure connecting wires to be stable O W Output AC connection Disconnect the breaker so as to ensure output AC ports without electricity AC output L connects to L of the single phase grid AC output N connects to N of the single phase grid The earthing wire connects to the earth Please ensure connecting wires to be stable moOWY y gt Communication connection When a PC is used to monitor one inverter or several inverters RS485 bus is applied as communication
8. 250V Operation at the Device 2 Stop Voltage 2 Volt Stop Below the set value the inverter will disconnect from the grid Click both AW for 0 5 1s Enter into submenu Click both AW for 1 2s Esc to previous menu A toadd or subtract VW to shift The set range 40 250V Click both AW for 0 5 1s to save setting 2 Volt Stop HYGCI 1I5CL User Manual Page 24 of 31 Operation at the Device 3 Start Time Waiting for this set time the inverter will connect to the 3 Time Start grid after the voltage gets the start voltage Click both AW for 0 5 1s Enter into submenu Click both AW for 1 2s Esc to previous menu A toadd or subtract VW to shift The set range 0 240S Click both AW for 0 5 1s to save setting om dee 4 Stop Time Waiting for this set time the inverter will disconnect from the grid after some disconnecting condition is got 4 Time Stop Click both AW for 0 5 1s Enter into submenu Click both AW for 1 2s Esc to previous menu A toaddor subtract VW to shift The set range 1 240Min Click both AW for 0 5 1s to save setting 4 Time Stop HYGCI 1I5CL User Manual Page 25 of 31 Operation at the Device 5 Serial No Settin
9. PT power curve 8 Curve Setting Click both AV for 0 5 1s Enter into submenu Click both AV for 1 2s Esc to previous menu The points amount of power curve is from 5 20 When these points are not set or wrong the inverter will find MPPT points automatically by software Click both AV for 0 5 1s Enter into submenu Click both AV for 1 2s Esc to previous menu Each point has 2 values the former is DC input voltage the latter is the maximum output power under this voltage Click both AV for 0 5 1s to save setting 1 Point1 000V 0000W HYGCI 1I5CL User Manual Page 28 of 31 Operation at the Device 9 Power Selection 9 Select Power To choose the mode of invert 1000 W or 1500 W Click both AW for 0 5 1s Enter into submenu Click both AW for 1 2s Esc to previous menu Click both AW fo 0 5 1s to save setting Click A or VW to choose Click both AW for 0 5 1s to save setting 10 Power Factor 10 Power Factor Click both AV for 0 5 1s Enter into submenu Click both AV for 1 2s Esc to previous menu Click A or w to set power factor 0 95 0 95 Click both AW for 0 5 1s to save setting HYGCI 1I5CL User Manual Page 29 of 31 Appendix Append
10. check if the grid is stable ErrorCode08 Under Grid Frequency Normal failure Please check if the grid is stable ErrorCode09 Under Grid Voltage Normal failure Please check if the grid is stable Normal failure Please check if the grid is stable Also ErrorCode10 Over Grid Voltage check the diameter of AC cable small diameter or longer length of the AC cable will cause this failure Normal failure please disconnect both input and output of ErrorCode11 IPM Error the inverter for at least 1 minute Re connect If malfunction is still there please contact dealer or manufacturer Normal failure please disconnect both input and output of the inverter for at least 1 minute Re connect Make sure ErrorCode12 Over Temperature the inverter is running in a cool dry place If malfunction is still there please contact dealer or manufacturer HYGCI 15CL User Manual Page 30 of 31 Error Code Phenomenon ErrorCode13 DSP Error ErrorCode14 Communication Error ErrorCode15 Boost Error ErrorCode16 Grid Connection Over Time Error ErrorCode19 Inverter Overload ErrorCode20 Dual CPU Check Error ErrorCode21 Over Voltage Turbine Output HYGCI 1I5CL User Manual Appendix Note Inverter will automatically restart when random failure occur If malfunction continually occur in a short period of time OR same error code occur frequently please check your system under instructions below Normal failu
11. g To set serial number of inverter Click both AW for 0 5 1s Enter into submenu Click both AW for 1 2s Esc to previous menu A toaddor subtract VW to shift Click both AW for 0 5 1s to save setting 5 SeNo Setting 6 Communication Setting This is to set the address and baud rate of RS485 Click both AW for 0 5 1s Enter into submenu Click both AW for 1 2s Esc to previous menu A to add or subtract W to shift Com Addr communication address Com Baud baud rate code matchup 0 9600 1 4800 2 2400 3 1200 gt Click both AW for 0 5 1s to save setting 6 Comm Setting HYGCI 1I5CL User Manual Page 26 of 31 Operation at the Device 7 RS485 Setting This is to set whether RS485 will be used which 7 RS485 Setting mode core or slave is to use Click both AW for 0 5 1s Enter into submenu Click both AW for 1 2s Esc to previous menu A toadd or subtract W to shift RS485 E D enable or disable 0 Ena Enable 1 Disa disable RS485 H S mode choice 0 Host core mode 1 Slave slave mode gt Click both AW for 0 5 1s to save setting 7 RS485 Setting HYGCI 1I5CL User Manual Page 27 of 31 Operation at the Device 8 Curve Setting To set MP
12. hange number W to shift 3 Time Setting Operation at the Device Page 21 of 31 4 Error record To look over error records at most of 10 pics 4 Error Record Click both AW for 0 5 1s Enter into submenu Click both AW for 1 2s Esc to previous menu The first line is error No The second line is error code The third line is error time 5 System advanced setting System advanced setting this needs a password 5 Sys Settings Click both AW for 0 5 1s Enter into submenu Click both AV for 1 2s Esc to previous menu 1 Volt Start HYGCI 15CL User Manual Operation at the Device Page 22 of 31 Operation at the Device The advanced system settings as follows 1 Volt Start Volt Start start voltage Volt Stop stop voltage Time Start start time Time Stop stop time SeNo Setting serial No Comm Setting set communication RS485 Setting set RS485 8 Curve Setting set power curve points 9 Select Power choose the mode 1000 W or 1500W 10 Power Factor set power factor oe ee el 1 Start Voltage 1 Volt Start Click both AW for 0 5 1s Enter into submenu Click both AW for 1 2s Esc to previous menu Click both AW for 0 5 1s to save setting HYGCI 1I5CL User Manual Page 23 of 31 A to add or subtract ww to shift The set range 40
13. implied warranty HYE offers a fee based manufacturer s guarantee of five years from the date of purchase i Exclusion of liability The country specific parameters of the grid must be set by the plant manufacturer of the WT according to the local grid parameters HYE is therefore not liable for damage due to wrong parameters on the grid end HYGCI 15CL User Manual Page 7 of 31 Description of the Device 4 Description of the Device 4 1 Technical Data Important technical data are also to find on the type plate attached to the device 4 R ated Ouret RR i Rated Voltage D 400VAC goovac EE Da eR ween ed ene te eee eR Ren er ae Ae AANE PE eee en eee a Brake Unit pe NG ae eee ee ee rn ee as ee eee ee ees DC output voltage range 0 280V 0 350V AC input voltage 0 200V 0 230V a Anacan o a E mer OC Ratedoulput ow sow Beak output 1100W adjuste 1600W adjusted i Ce a po Working voltage i stst lt Vc a amon BAS EE cack amp zo A C outputvotage ZZOVIBOVANAN eo Output frequency ee Output standard option CE EMO CE LVD VDE0126 14 ae Powerfactor i 4 50 99 fullload aea o lt S95 sstst TO term se Protection grade sti OO 5 Ambient temperature 1 0 wwe miy 90 HYGCI 15CL User Manual Page 8 of 31 Description of the Device RR Rg HDR PSOE RAB HS RE SSS TBST RS SS TS ASHE SS TE SIFTS RSE SS SR SS Ta SoS SES SEB RE SST FES SMS SS PS RH EEF TST RE
14. ix Trouble Shooting Note Inverter will automatically restart when random failure occur If malfunction continually occur in a Error Code Phenomenon short period of time OR same error code occur frequently please check your system under instructions below Severe malfunction Please turnoff wind turbine system ErrorCode01 Over Input Voltage immediately and contact dealer or manufacturer Normal failure please disconnect both input and output of ErrorCode02 Over Inverter Bus Voltage the inverter for at least 1 minute Re connect If malfunction is still there please contact dealer or manufacturer Normal failure please disconnect both input and output of ErrorCode03 Over Instantaneous Input c the inverter for at least 1 minute Re connect If malfunction urren is still there please contact dealer or manufacturer Severe malfunction Please turn on manual break ErrorCode04 Over Mean Input Current immediately to stop the turbine and contact dealer or manufacturer Normal failure please disconnect both input and output of ErrorCode05 Over Instantaneous the inverter for at least 1 minute Re connect If malfunction Output Current EDIN is still there please contact dealer or manufacturer Severe malfunction Please turn on manual break ErrorCode06 Over Mean Output Current immediately to stop the turbine and contact dealer or manufacturer ErrorCode07 Over Grid Frequency Normal failure Please
15. ntion that the device is not tilted to the front The mounting angle should be 90 Fig 7 Type of mounting and tilt angle Use the wall mount provided with the devices to mount the HYGCI 15CL V1 0 V1 5 simply and safely Mount the device as follows Select a mounting location for simple operation The display should be at eye level of the operator Fasten the wall mount to a vertical wall using the fixings and the hexagon head bolts supplied with the device Make sure that the wall mount is tightened firmly Place the HYGCI 15CL V1 0 V1 5 on the edges of the angular mounting rails so that it is tilted to the front Position the device so that the slide in rails of the wall mount fit into the grooves of the HYGCI 15CL V1 0 V1 5 on both sides Tilt the HYGCI 15CL V1 0 V1 5 to the rear then and move it vertically into the wall mount The angular mounting rails interlock with the bent outer fins of the device to ensure secure hold HYGCI 15CL User Manual Page 13 of 31 5 2 Installation Electrical Connection RS485B a yellow R5485 por AC input single phase AC Reta SA blue L N earthing turbine grid Fig 8 Connection of HYGCI 15CL V1 0 V1 5 to small wind turbine and public grid gt Connection to The Grid A HYGCI 15CL V1 0 V1 5 is designed for the 230V single phase utility grid whose voltage is between 196V 264V and frequency is between 47 5Hz 51 5Hz Rerating according to VDE 0126 1
16. nual Page 6 of 31 Safety Instructions 3 7 Disposal The HYGCI 15CL V1 0 V1 5 fulfills the requirements covered in the Directive 2002 95 EC on the restriction of the use of hazardous substances in electrical and electronic equipment RoHS Directive ooh The HYGCI 15CL V1 0 V1 5 must not be disposed as part of domestic Sat waste According to the European Directive 2002 96 EC about old a electrical and electronic equipment and the implementation into national e law exhausted electric equipment must be collected separately and recycled in an environmentally acceptable way Make sure that you can return the used device to the merchant It may have potential effect on the environment and on your health if you disregard the EC Directive 3 8 Guarantee and Liability The guarantee period is two years from the date of delivery implied warranty Guarantee claims are excluded lt when the device has been employed beyond its intended use in terms of section 3 2 Appropriate Use P 5 lt when the device has been mounted non standard or improperly especially by electricians without license lt when the device has been employed although the protection equipment was defective lt when the maximum permissible input voltage has been exceeded lt through improper operation lt when the device or its equipment have been modified lt when the device was affected by foreign material or force majeure In addition to the
17. of several feed in converters of the tyoe HYGCI 15CL V1 0 V1 5 on the generator end 3 4 Mains Monitoring The device interrupts operation in case of line interferences e g in the event of an AC power failure The grid feed in is stopped according to the country specific standard e g DIN V VDE V 0126 1 1 This way dangerous voltage in the AC conductors is avoided when a mains failure occurs HYGCI 15CL User Manual Page 5 of 31 3 5 Safety Instructions Storage Transport and Setup NOTICE Storage and transport without original packaging When the device is stored or transported withoutthe original packaging this is to be considered as extraordinary burden and may cause property damage Store the device in a dry well ventilated room Store and transportthe device onlyin original packaging in compliance with class 2Mii according ta DIN EN 0721 3 8 1998 03 The HYGCI 15CL V1 0 V1 5 is tested for mechanical shock mechanical oscillation and its fatigue strength under oscillation stresses according to DIN VDE 50178 1997 class 3M1 NOTICE Property damage dus to lecea setup Qscillaton beyond the limiting value or application onto non stationary equipment is to be considered extraordinare burden and can cause property damage Mountthe device shock proof and tree of oscillation to a wall according to the reg ulations for stationary appliances 3 6 Environmental Conditions Pay attention to the following no
18. r EMC Electro magnetic compatibility EN European standard German Europaische Norm IEC International Electrotechnical Commission VDE Association of German Electricians German Verband Deutscher Elektrotechniker WT Wind Turbine HYGCI 15CL User Manual Page 3 of 31 General Information 2 General Information Read this manual carefully and pay attention to the safety instructions iS embodied This manual describes the feed in inverter HYGCI 15CL V1 0 V1 5 developed by HYE This device is used for grid connected operation of small wind turbines WT HYGCI 15CL V1 0 is suitable for HY 1000 wind turbine while HYGCI 15CL V1 5 is suitable for HY 1500 wind turbine which means the energy generated by the WT is supplied to the connected grid Therefore the HYGCI 15CL V1 0 V1 5 converts the speed dependent AC DC voltage of the WT into a grid compatible AC voltage For this process grid voltage is necessary In the event of a mains power failure or when the WT generates more energy than the HYGCI 15CL V1 0 V1 5 can feed to the grid the integrated intelligent electronic break system will automatically trigger inverter will auto rest after a while when gust wind passes and system will start to generate electricity again Fig 1 Principle block diagram of HYGCI 15CL V1 0 V1 5 between small wind turbine and grid The HYGCI 15CL V1 0 V1 5 accommodates the components rectifier and inverter in a compact housing The HYGCI 15CL
19. re please disconnect both input and output of the inverter for at least 1 minute Re connect If malfunction is still there please contact dealer or manufacturer Normal failure please check the communication cable is connected in correct manner If malfunction is still there please contact dealer or manufacturer Normal failure please disconnect both input and output of the inverter for at least 1 minute Re connect If malfunction is still there please contact dealer or manufacturer Normal failure please disconnect both input and output of the inverter for at least 1 minute Re connect If malfunction is still there please contact dealer or manufacturer Normal failure please shut down the inverter for 10 minutes If malfunction is still there please contact dealer or manufacturer Normal failure please disconnect both input and output of the inverter for at least 1 minute Re connect If malfunction is still there please contact dealer or manufacturer Normal failure normally this situation will occur under severe weather conditions After 1st severe weather amp Turbine automatically restart in 10 minutes if second strike comes condition strike Inverter system it will within one hour system will automatically restart in 30 minutes if third strike comes within one hour system will assume a big storm is coming and will trigger safety mode stop for 12 hours then after restart Page 31 of 31
20. reen displays turbine status for example system status offline 7 2 System State Screen After initializing it shows Offline standby status When all connecting conditions are fulfilled it shows Connecting When the turbine output power is low it shows Low Wind When manual brake is on it shows Manual Brake On After the inverter connected to the grid it shows Online connected status HYGCI 1I5CL User Manual Page 18 of 31 7 3 Device Status In any interface click both AW more than 2s to enter value interface Click A Z4 v to next page Graph peak power of every hour Ppk day peak power of the day Click A 66 v to next page U_AC AC output voltage I_AC AC output current FREQ Grid frequency Click A A v to next page U_DC DC input voltage I DC DC input current Click A e v 22 to next page System version 0 1 0 version code 7 4 System Settings Operation at the Device The user can enter into the setting screens at any above screen by pressing both buttons ho F gt quickly for 0 5 1s There are two types of setting user and system The system setting is only operated by the qualified personnel and needs the password which can be reset HYGCI 15CL User Manual Page 19 of 31 The user settings as follows 1 STOP manual stop 2 START manual sta
21. rt 3 Time Setting set time 4 Error Record retrieve error record 5 Sys Settings system advanced setting Page 2 1 Manual stop 1 STOP manual stop Under special circumastance this function can disconnect the inverter from turbines and the grid Click both AW for 0 5 1s Enter into submenu Click both A V for 1 2s Esc to previous menu Click both AW for 0 5 1s to save setting Click A or V to choose Click both AV for 0 5 1s HYGCI 15CL User Manual Operation at the Device Page 20 of 31 2 Manual start This function is to restart the inverter after manual stop By this function the machine will turn into automatic operation Click both AW for 0 5 1s Enter into submenu Click both AW for 1 2s Esc to previous menu Click both AW for 0 5 1s to save setting Yes Click A or W to choose Click both AW for 0 5 1s No 3 Time setting This is to set the current time on LCD 3 Time Setting Click both AV for 0 5 1s Enter into submenu Click both AV for 1 2s Esc to previous menu edit position TIME current ttme DATE current date Click both AV for 0 5 1s to save setting HYGCI 15CL User Manual In setting click A to c
22. tallation This chapter first describes the mounting of the HYGCI 15CL V1 0 V1 5 to the wall followed by the electrical connection Mounting the HYGCI 15CL V1 0 V1 5 The HYGCI 15CL V1 0 V1 5 is mounted vertically to a weight bearing wall using the wall mount provided Please consider the safety instructions and application advice and the technical data when mounting the device A dry dust free room provides for ideal environmental conditions ZS Risk of fire due to hot surfaces During operation individual device parts can reach a temperature of 60 C and may cause a fire A fire can cause serious personal injury and property damage Make sure that there are no combustible materials near by the device Ventilation and Free Space The HYGCI 15CL V1 0 V1 5 isn t convection ventilated an internal fan is necessary A greater amount of space must be provided above the device so it can be moved into the wall mount Keep the spacing to other devices 100 cm HYE 50 cm Grid Tied Inverter For Wind Turbines One uleur olien pour connenion sid reau 50 cm Fig 6 Required space to other devices When the circulation of air is restricted the HYGCI 15CL V1 0 V1 5 IE may overheat and switches off Do not put anything onto the device and clean the fan HYGCI 15CL User Manual Page 12 of 31 Installation 5 1 2 Mounting Instructions HYENERGY recommends mounting the device to the wall vertically Pay atte
23. tes to provide for a long service life and trouble free operation lt Protect the device against mechanical damage lt Protect the device against dirt and humidity lt Protect the device against direct sunlight Excessive solar radiation will impair the service ability of the device The optimum ambient temperature is in the range of 10 20 C lt Take care that a sufficient amount of space is provided around the device When the operation mounting place is outside the denoted area this is to be considered not intended Precise information on the permissible ambient conditions are given in the technical data Maintenance The HYGCI 15CL V1 0 V1 5 is designed for a minimum amount of maintenance We recommend checking the following functions at regular intervals in order to ensure a proper operation of the device lt Check on a regular basis preferably weekly whether the device operates properly This should be done at different wind conditions You can recognize the proper operation by means of the displayed operating modes Serious errors are displayed by the red LED lt Pollution of the heat sink can restrict the heat dissipation Check the heat sink for dirt on a regular basis and clean it with a paintbrush a soft brush or compressed air lt Clean the display and the LED display with a moist cloth when it is dirty Do not use harsh cleaning agents e g abrasive solvent or acid substances HYGCI 15CL User Ma
Download Pdf Manuals
Related Search