USER'S MANUAL
Contents
1. 066 PARKING SENSOR SYSTEM USER S MANUAL 9 MAR AGEMENT 003 ISO TS 16949 2002 FM 505383 ISO 9001 2000 FM 78496 GENERAL INSTALLATION DIAGRAM Display Control box Working Conditions 1 When reverse the car 8 sensors work at the same time The distance from nearest obstruction and the bumper will be shown on the display with horn alarming and direction indicator 2 When drive forward only the front sensors work Three options to control the front sensors Yellow wire of Switch a Control by switch front control box ON ACC When switch on the front sensors start to work Yellow wire of b Control by braking frontcontrol box 2 Braking signal When brake the car the front sensors start to work when stop braking the front sensors stop working in 30 second Yellow wire of Switch c Control by both the switch and braking front control box _ Braking signal When switch on the front sensors start to work as above mentioned option b Black wire Earth Red wire 12V ON ACC Control Switch Red wire reversing light Black wire reversing light LCD DIGITAL DISPLAY Front Back 0 7 0 6m 1 5 1 1m Safety Area 0 5 0 4m 1 0 0 4m Alarm Area 0 3 0 0m 0 3 0 0m Danger Area Front Back 0 7 0 6m2. 8 This system is a reversing aid and the manufacturer will take no responsibility for any accidents caused after the kit is installed
3. 1 5 1 1 Safety Area 0 5 0 4m 1 0 0 4m Alarm Area 0 3 0 0m 0 3 0 0m Danger Area DETECTING RANGE SENSOR INSTALLATION DIAGRAM Top View Side View DISPLAY STATUS o s 5 27 07 T 12 007 z Z T A TUAN 22 77 0 6 0 8m 0 3 0 4m 0 6 0 8m 0 3 0 4m Front detection tz CSD Alarm Area 40 50cm Alarm Area 40 100cm The best position for 2 sensors The best position for 4 sensors The direction of sensors q0 GE Danger Area 0 30 Bandes E insertin ln ap 6 The direction of sensors 1 Advised position to install the sensors da da A 4 drilled holes A B C D should be under the same line Vertical installation position to the ground Sloping installation position to the ground Stick on and insert in sensors in various shapes for options B 0 5 0 8m vertically high to the ground 0 55 is recommended Objects absorbing Smooth slope
4. Smooth round objects wave e g Cotton C Vertical tidy surface without metal components is preferred ge Objects hard to be detected INSTALLATION TOOLS A Choose suitable drilling position for A amp D sensor with relevant mark from the side 11CM is recommended and 20 with the side P lt CN B To perform the best detecting angle select the position for A amp P D sensor with 8 13CM away 3 Select drilling position for sensor B amp C A Measure the distance between sensor A and D get the result L Bracket 1 Fix the display on rear mirror Display is adjustable for different vision angel Bracket 2 B Mark sensor B amp C for every 1 3 L interval Fix the display on dash board Locate the control box in the The display should boot keep safe cool dry be installed where and away from shake and easy to be seen interference A Drill with a small awl to B Drill with the original locate driller A Insert the sensors into the holes one by one and tighten them The sensor with metal slice must be installed following the direction B Hide the wires in good order according to various cars 066 PARKING SENSOR H 066 Parking Sensor System c
5. ether there is any obstacle around it or the sensor is fixed too tight or close to great interference sources such as vent pipe wires b If the display shows any distance figure with no obstacle around the sensor the sensor may detect the ground or some outshoots of the car such as registration mark etc please check the directions of sensor and axes c If the system still could not work properly after the above mentioned handling the sensor s can be deemed defective or unmatch with the control box The system should be replaced Note a The connection between sensor and the digital control box is unique b It performs as when detecting within 0 3m it shows 0 0 instead of 0 1 0 2 to alert which requires the driver to stop immediately NOTE 1 The car must be in power off when installing ultrasonic sensors 2 Its performance may be affected in following situation heavy rain gravel road bumpy road sloping road and bush very cold hot or moist weather or the sensors is firned or iced over 3 Switches among ultrasonic electric wave DC and AC and those among 24V 12V voltages may also effects its performance 4 The sensors should be installed appropriate loose or tight 5 Its performance will be effected if the sensors are fixed on metallic bumper 6 Avoid installing the digital control box in places of great interference such as vent pipe wiring nearby 7 Test the system to make sure it works normally before using
6. onsists of ultrasonic sensors digital control box and LCD display The system detects the distance between the car and front rear obstruction by ultrasonic sensors installed at the front rear bumper of car The distance will be displayed in an innovative mode with the special designed LCD numeric display and step up sounds which will be changed according to the actual positions detected obstruction so that the driver could judge the distance and avoid accident MAIN FEATURES Digital LCD display Three stage simulation alarm Front and back detection Four stage simulation distance display DingDingDing DangDangDang alarm sound Hidden installation Switch Braking delay control Self test function of sensor TECHNICAL SPECIFICATIONS Rated Voltage DC 12V Operating Range DC 10 16V Operating Current 30 360mA Detecting Distance Front 0 3 0 7m Rear 0 3 1 5m Ultrasonic Frequency 40KHz Working Temperature of Control Box 30 70 C Working Temperature of Display 20 70 C Display Size 70 32 14mm ALARM MODE Front detection Alarm Sound Digital Display Alarm Color Safety Area Silence Safety Area Ding Ding Ding Alarm Area Ding Ding Ding Digital Display Alarm Color Safety Area Safety Area Alarm Area Danger Area INSTALLATION STEPS 1 Choose rightinstallation position for sensors 2 Select drilling position forsensorA amp D Select drilling
7. position for sensor 1 amp 4 Select drilling position for sensor B amp C C Select drilling position for sensor 2 amp 3 4 Locate the position and drill 5 Install the sensors and hide wires 6 Install the display 7 Install the control box 8 Connect the whole system according to the General Installation Diagram INSTALLATION AND TEST 1 Adjust the directions of the sensors and axial orientation neaten the wiring after installing the sensors 2 Connect the power supply of back control box to the reversing light Connect the power supply of front control box to auto ignition switch 3 Connect the data wires between the front control box and display and disposal the control switch with front control box Do not disposal the sensor at the moment 4 When the car is started the horn sounds Dang Dang to enter into working status 2s later it turns to standby status Put the car into back gear then the display shows En n 0 1 2 show the number of defective sensors with the indication of exact defective sensors Insert one of the sensors into corresponding interface in front back control box Human being could be detected normally if he stands within 0 7 right before the sensor Pull out the sensor and check other sensors in the same method Insert all the sensors in corresponding interfaces after testing Test a After connect a sensor with the control box if the buzzer sounds Bi please check wh
Download Pdf Manuals
Related Search