Home
Bionaire BSF1211C-MU Owner's Manual
Contents
1. holes are aligned and tighten Converting to a Table Fan An additional short pole Q is supplied which allows the an to be converted into a table fan see Figure 2 To change to this short pole remove the fan head assembly from its position on top of the inner pole extension N and unscrew the T shaped locking lever U at the base Remove the outer pole P replace with the short pole Q and reassemble as detailed above IN 3 n i l i u i Iiag EERE l i EE N x OPERATING INSTRUCTIONS 1 Set fan base on a dry level surface 2 Plug cord into any standard 120 volt AC outlet Please make sure the Speed Control Knob is in the OFF 0 position Speed Control Knob is located on the Fan Motor Housing The SPEED is adjusted by turning the Speed Control Knob to the desired setting 0 3 2 1 The OSCILLATION control knob is located on the op of the Fan Motor Housing To start Oscillation pus Control knob down To stop Oscillation pull Speed Control Knob up ADJUSTMENT INSTRUCTIONS Tilt Adjustment Follow these instructions to tilt the Fan Head for upward angle air movement 1 To change the tilting angle of the fan head simply loosen the tilt adjustment knob K 2 Move the fan head to the desired angle and firmly tighten the tilt adjustment knob to lock into place m e Height Adjustment Follow these instructions to adjust the height of the fan 1 Turn the pole locking knob 0 counter clockwi
2. FAN CLEANING FAN STORAGE INSTRUCTIONS hil Hie the fan before cleaning or period after Your fan should be stored in the off season in its original ii vara ucier to drio on or into the fan motor POX It is important to keep it in a safe dry location housing p e We recommend using the original or appropriately Do not use any of the following as a cleaner sized box gasoline thinner benzine dh T memi to protect the fan from dust or Fan Blade Cleaning 1 To access the fan blade remove the front grill and securing screw 2 Clean the fan blade front and rear grills with a soft moist cloth 3 Replace blade tighten securing screw and securel fasten the front grill see detailed instructions in the Fan Head Heat section Fan Head Base and Pole Cleaning Using a soft moist cloth with or without a mild soap solution carefully clean the fan base pole and head Please use caution around the motor housing area Do not allow the motor or other electrical components to be exposed fo water If you have any questions regarding your product or would like to learn more about other Bionaire products please contact our Consumer Service Department at 1 800 253 2764 or visit our website at www bionaire com 2012 Sunbeam Products Inc doing business as Jarden Consumer Solutions All Rights Reserved Distributed by Sunbeam Products Inc doing business as Jarden Consumer Solutions Boca Raton Florida 33431 154133_R
3. an JCS or an authorized JCS service center Further the warranty does not cover Acts of God such as fire flood hurricanes and tornadoes What are the limits on JCS s Liability JCS shall not be liable for any incidental or consequential damages caused by the breach of any express implied or statutory warranty or condition Except to the extent prohibited by applicable law any implied warranty or condition of merchantability or fitness for a particular purpose is limited in duration to the duration of the above warranty JCS disclaims all other warranties conditions or representations express implied statutory or otherwise JCS shall not be liable for any damages of any kind resulting from the purchase use or misuse of or dea to use the product including incidental special consequential or similar damages or loss of profits or for any breach of contract fundamental or otherwise or for any claim brought against purchaser by any other party Some provinces states or jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts so the above limitations or exclusion may not apply to you This warranty gives you specific legal rights and you may also have other rights that vary from province to province state to state or jurisdiction to jurisdiction How to Obtain Warranty Service In the U S A If you have any questions regarding this warrant
4. ev A BSF1211 MU_12EMI GCDS B1027509 PH Printed In China BSF1211C MU_12EM1 indd 1 3 YEAR LIMITED WARRANTY Sunbeam Products Inc doing business as Jarden Consumer Solutions collectively JCS warrants that for a period of three years from the date o purchase this product will be free from defects in material and workmanship JCS at its option will repair or replace this product or any component of the product found to be defective during the warranty period Replacement will be made with a new or remanufactured product or component If the product is no longer available replacement may be made with a similar product of equal or greater value This is your exclusive warranty Do NOT attempt to repair or adjust any electrical or mechanical functions on this product Doing so will void this warranty This warranty is valid for the original retail purchaser from the date of initial retail purchase and is not transferable Keep the original sales receipt Proof of purchase is required to obtain warranty performance JCS dealers service centers or retail stores selling JCS products do not have the right to alter modify or any way change the terms and conditions of this warranty This warranty does not cover normal wear of parts or damage resulting from any of the following negligent use or misuse of the product use on improper voltage or current use contrary to the operating instructions e repair or alteration by anyone other th
5. fore putting on or taking off parts and before cleaning Avoid contact with moving parts Do not eae in the presence of explosive and or flammable fumes To avoid fire hazard NEVER place the cord under rugs or any parts near an open flame cooking or other heating appliance Do not operate any appliance with a damaged cord or plug after the appliance malfunctions or has been ropped damaged in any manner Discard fan or return to an authorized service facility for examination and or repair Do not run cord under sell Do not cover cord with throw rugs runner or similar coverings Do not route cord ine furniture or appliances Arrange cord away from traffic area and where it will not be tripped over The use of attachments not recommended or sold by the appliance manufacturer may cause hazards 12 Do not let the cord hang over the edge of a table counter or come in contact with hot surfaces or leave exposed to high traffic areas 13 Do not use outdoors 14 To disconnect grip plug and pull from wall outlet Never yank on at 15 Always use on a dry level surface 16 Do not operate fan until fully assembled with all parts properly in place 17 This product is intended for household use ONLY and not i commercial or industrial applications 18 WARNING To reduce the risk if electrical shock and injury to persons do not use in window 19 WARNING To reduce the risk of fire or electric shock do
6. not use this fan with any solid state speed control device 20 This product employs overload protection fuse A own fuse indicates an overload or short circuit situation If the fuse blows unplug the product from the outlet Replace the fuse as per the user servicing instructions follow product marking for proper fuse rating and check the product If the al al fuse blows a short circuit may be present and the product should be discarded or returned to an authorized service facility for examination and or repair PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS outlet reverse the P electrician to install t BSF1211C MU_12EM1 indd 2 a polarized outlet ahy U THIS APPLIANCE HAS A POLARIZED PLUG one blade is wider than the other To reduce the risk of electric shock this plug is intended to fit in one way If the plug does not fit fully in the g If it still does not fit contact a qualified e proper outlet DO NOT ATTEMPT TO MODIFY THIS PLUG OR DEFEAT THIS SAFETY FEATURE IN ANY WAY ASSEMBLY INSTRUCTIONS Assembly Time 10 15 minutes Tools Required Phillips head screw driver NOTE Make sure you remove all contents from the RT Please check packaging materials for parts that could be required to operate your fan Base Pole Assembly You will need the base cover R si S outer pole P washer T and T shaped locking lever U 1 Turn the base cover upside down and place the weight into
7. p and bottom of the rear grill fit over the prongs on the motor housing H Make sure that the carry handle is topmost on the motor assembly Secure the rear grill E in its place using the rear grill mounting nut D Turn this nut clockwise and tighten firmly Loosen the securing screw C on side of the fan blade B to slide the fan blade onto the motor shatt F through the rear protrusion Make sure the securing screw C rest on the notch flat side of motor shaft and tighten the screw C CAUTION Avoid contact with sharp end of blades 4 Centre the front grill A by aligning the Bionaire logo on the logo plate so that it is horizontal and parallel with the a Then place the bracket at the top over the front and rear grills with the hole on the bracket going through the center vertical bar Fasten the other clips making sure they go over both the front and rear grills 5 ee grill screw and nut V and tighten with screw river Final Assembly NOTE The fan head locking knob L is attached with the additional short pole Q when shipped Slide the inner pole extension N ji from the outer pole P first loosening the pole locking knob 0 to securely hold this position Tighten the pole locking knob 0 2 Place the fan head assembly into this extension pole inserting the fan s head neck M into the pole opening 3 Add the fan head locking knob L to the hole in the fan head s neck M making sure
8. se to oosen the pole 2 fle the pole to the desired ti and firmly ten the locking knob in a clockwise direction tig CLEANING MAINTENANCE INSTRUCTIONS Follow these instructions to correctly and safely care for your fan Please remember REPLACEABLE FUSE If your 5 Amp 125 Volt replaceable fuse blows please order a new fuse at 1 800 253 2764 Follow the below instructions to replace the fuse on the plug User Servicing Instructions l Unplug your fan Grasp plug and remove from the BERAN or other outlet device Do not unplug by pulling on cord Open his cover located on the top of the plug b using your thumb or a flathead screwdriver to slide the cover down towards the prongs Note Ensure that fuse cover is completely open before attempting to remove fuse Remove fuse carefully by using a small screwdriver to pry the fuse out of the compartment by the metal ends of the fuse see Fig 3 Place plug on a solid ft surface Insert new 5 Amp 125 Volt fuse into fuse sal al and use a small screwdriver to secure the metal ends of the fuse into the compartment Caution Risk of fire Replace fuse only with 5 Amp 125 Volt fuse Slide fuse cover closed completely If fuse cover is difficult to close make sure fuse is secured in place completely by pressing down on metal ends of the use Risk of fire Do not replace attachment plug Contains a safety device fuse that should not be removed Discard product if
9. the attachment plug is damaged Fig 3 10 12 12 11 13 AM
10. the base cover 2 Insert the threaded end of the T shaped locking lever into the hole of the washer weight and through the base cover 3 While holding the base cover and weight with one hand aia connect the outer pole to the base SY N I Y I N AN S SZ ZEE z z S gt G A WW a ll SZ WE H yj SZ A C AIE S jp o A H S Z U G SG Z Z h ME N f M ly SZ SSA f Front Grill Fan Blade Securing Screw Grill Mounting Nut Rear Gri Motor Shaft Plastic Sleeve Motor Ha Speed Control Knob Oscillation Control Knob Tilt Adjustment Knob Fan Head Locking Knob Fan Head s Neck Inner Pole Extension Pole Locking Knob Outer Pole T Washer Additional Short Pole U T Shaped Locking Base Cover Lever Weight V Grill Screw and Nut A B C D E F G H l J K L M N 0 P Q R gt sliding the T shaped locking lever into the bottom of the outer pole with your other hand 4 Turn the T shaped locking lever clockwise to securely attach the pole to the base 5 Set the base on the floor weight side down Fan Head Assembly You are now ready to assemble the fan head 1 Remove the protective sleeve G and unscrew pril mounting nut D by turning counter clockwise trom the motor shaft F Position the rear grill E over the motor shaft F making certain that the vertical slots at the to
11. y or would like to obtain warranty service please call 1 800 253 2764 and a convenient service center address will be provided to you In the U S A this warranty is offered by Sunbeam Products Inc doing business as Jarden Consumer Solutions located in Boca Raton Florida 33431 If you have any other problem or claim in connection with this product please write our Consumer Service Department PLEASE DO NOT RETURN THIS PRODUCT TO ANY OF THESE ADDRESSES OR TO THE PLACE OF PURCHASE P BIONAIRE pure indoor living 2 IN 1 DUAL Desk Stand FAN MODEL BSF1211C Instruction Leaflet Read instructions before operating Retain for future reference l z Questions Comments Call 1 800 253 2764 in North America or visit our website at www bionaire com 10 12 12 11 13 AM l 2 3 l PLEASE READ AND SAVE THESE IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances basic safety precautions should always be taken including the following Read all instructions before using this appliance Use fan only for purposes cats in the instruction manual To protect against electrical shock do not immerse unit plug or cord in water or spray with liquids and plug the appliance directly into a 120V AC electrical outlet Close supervision is necessary when any appliance is used DY or near cniaren Unplug from outlet when not in use when moving fan from one location to another be
Download Pdf Manuals
Related Search
Related Contents
Toshiba Satellite P70-A0LX Elycytor PS.6 - Grupo Clinica Agricola Amazon ElastiCache User Guide Copyright © All rights reserved.
Failed to retrieve file