Home

ASRock EN2C602/D12 Owner's Manual

Contents

1. olo PCICLK FRAME 3t 0 a System Panel Header 9 PANEL 1 see p 16 18 21 25 27 30 1 This connector supports Trusted Platform Module TPM system which can securely store keys digital certificates passwords and data A TPM system also helps enhance network se curity protects digital identi ties and ensures platform integrity This header accommodates several system front panel functions Connect the power switch reset switch and system status indica tor on the chassis to this header according to the pin assignments below Note the positive and negative pins before connecting the cables 56 Auxiliary Panel Header 18 pin PANEL 1 see p 16 19 22 25 28 31 PWRBTN Power Switch Connect to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch RESET Reset Switch Connect to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart PLED System Power LED Connect to the power status indicator on the chassis front panel The LED is on when the system is operating The LED keeps blinking when the sys tem is 51 53 sleep state The LED is off when the system is in S4 sleep state or powered off S5 HDLED Hard Drive Activity LED Co
2. quo INT 199 1194 100MHz PCIE Gen3 BUS PCI E Gen3 X4 SLOT X4 PCIE Slot xl PCIE PCI E Gen3 X16 SLOT x16 X8 100MHz PCI E 3 16 SLOT x8 X0 100MHz 100MHz SENS Tm he 182574L INTEL pum km C602 st Fert H5 100MHz PCH C602 chipset only SATA 2 0 Zu 100MHz 1 1 PEED D SUB_Connector 1872300 PCIExI COM Port Connector SPI 64Mb Realtek PHY 8211E LPC BUS Nuvoton KB MS SPI FLASH NCT6776 uu 42 EN2C602 on Board on Board Intel Processor Intel Processor CHE X DDR3 1066 1333 1600 RT 8 SNB EN IVB EN SNB EN IVB EN CHF DDR3 1066 1333 1600 LGA 1356 Pin Socket LGA 1356 Pin Socket CPU CPU BUR DDR3 1066 1333 1600 PCIE Gen3 x16 Slot x16 100MHz PCIE Gen3 BUS PCI E Gen3 X4 SLOT X4 PCIE Gen2 1 Slot 1 PCIEX1 PCI E Gen3 X16 SLOT x16 X8 100MHz DDR3 1066 1333 1600 DDR3 1066 1333 1600 i 1066 1333 1600 gue 199 3124 m P PCI E 3 X16 SLOT x8 X0 STEMS See qun INTEL C602 ST 550 __ 552 WT 71557 7 LAN MER PCH C602 chipset only SATA 2 0 PCIEx2
3. Either end of the SATA data cable can be connected to SATA SATA2 hard disks or the SATA2 connectors on this mother board Serial ATA SATA Data Cable 54 SCU Connectors These eight SCU connec SCU PORT 0 tors support SAS SATA data SCU PORT 1 PORT 0 SCU PORT 2 SCU PORT 4 SCU PORT 6 cables for internal storage SCU PORT 2 SCU PoRr 3 1222 E devices The current SAS2 2 CU PORT SCU 3 scu 5 scu 7 SATA3 interface allows up 5 PORT 4 SCU PORT 5 to 6 0 Gb s data transfer IJ I SCU PORT 6 rate For connecting SAS SCU PORT 7 HDDs please contact SAS see p 15 18 21 data cable dealers PORT 0 SCU PORT 1 om me SCU_PORT_2 SCU PORT 0 SCU PORT 2 SCU PORT 3 SCU PORT 4 E 5 SCU PORT 5 SCU PORT scu PoRT3 2 SCU PORT 6 SCU PORT 7 see 24 27 30 USB 2 0 Headers QS Besides two default USB and Ports Dummy 2 0 ports on the panel 9 pin USB 2 3 there are are two USB 2 0 see p 16 18 21 24 27 30 9 USB 4 5 see p 16 19 22 24 27 30 headers and one port on this motherboard Each USB 2 0 header can support two USB 2 0 ports A USB PWR USB 6 re see p 16 19 22 25 27 30 e 55 TPM Header 2 lt 23 E 17 pin TPM1 lt 5 see p 16 19 22 25 28 31 2 g 2 t 2
4. 22 23 gt gt lt 7 CPU Fan Connector CPU FAN1 2 CPU Fan Connector CPU FAN1 1 SPI Flash Memory 64Mb SATA3 Connector SATAII O 1 White 17 SATA2 Connector SATAII 2 3 Blue SATA2 Connector SATAII 4 5 Blue Clear CMOS Pad CLRCMOS2 E 27 SCU Connector SCU PORT 2 3 Blue USB 2 0 Ports USB 6 System Panel Header PANEL 1 Intel C602 Chipset BON 27 7 35 _ LN ES 29 d EN LE CNN O EN LE CNN LE EN LUMINE ES ___ LEN LN ES 54 28 EN2C602 PS2 Keyboard Y9A ATX12V 1 ATXPWR1 1 PSUSMB1 26 7cm 10 5 in DDR3 C1 64 bit 240 pin module DDR3 C2 64 bit 240 pin module FRNT_FAN1 30 5cm 12in 22 54 H 8 i 1 LAN2 H 5 5 O 52 IPMI 2 LAN DDR3 G2 64 bit 240 pin module 51 O DDR3 G1 64 bit 240 pin module 50 DDR3 F1 64 bit 240 pin module LIL 49 mg DDR3 E2 64 bit 240 pin module 48 PCIE6 2 602 47 5 46 45 4 Intel RoHS cn T ASRock re Super ME RECOVERY1 43 PCIE2 we sono ssor aes Y C um uem 42 PCIE1 usss prms
5. Supports Energy Efficient Ethernet 802 3az Supports Quad LAN with Teaming function Supports PXE EN2C606 4L Intel C606 2 x SATA3 6 0 Gb s 4 x SATA2 3 0 Gb s support RAID 0 1 5 10 and Intel Rapid Storage 3 0 EN2C602 4L EN2C602 Intel C602 2 x SATA3 6 0 Gb s 8 x SATA2 3 0 Gb s support RAID 0 1 5 10 and Intel Rapid Storage 3 0 Marvell SE9220 2 x SATA3 6 0 Gb s support RAID 0 1 NCQ AHCI and Hot Plug functions EN2C606 4L Intel C606 8 x SATA2 SAS 3Gb s support RAID 0 1 5 10 EN2C602 4L EN2C602 11 EN2C606 4L EN2C602 4L 4x RJ45 Gigabit Ethernet LAN ports Rear Panel 1x RJ45 Dedicated IPMI LAN port LAN Ports with LED ACT LINK LED and SPEED LED Lan port EN2600 2x RJ45 mE Ethernet LAN ports 1 x RJ45 Dedicated LAN port LAN Ports with LED ACT LINK LED and SPEED LED Serial port COM1 Type AUSB 1 2 0 port USB 2 0 2 Each support 2 USB 2 0 1x COM from 80 debug 1 port LED Auxiliary panel header Au Front panel 000000 Connector 1 L pin Thermal sensor 1 header 8 8 x 4 pin 2 x 3 pin CPU fan header have 3 pin and 4 pin ones Two types couldn t be used at the same time 1 include chassis intrusion location button amp LED front LAN LED Fan header 12 PSUSMB header Internal Dr Debug Connector with LED 1 ATX power 1 24 pin 2 8 pin Plug and Play PnP ACPI 1 1 Compliance Wake U
6. USB 23 0584 5 TT 7 grs un 41 40 39 38 37 36 3534 93332 31 3029 28 27 2625 24 29 t ATXPWR1 _1 E C1 C2 White 7 CPU Fan Connector CPU FAN1 2 _1 E n 0 Mf White 0 1 White 2 3 5 _LED_ CPU Fan Connector CPU FAN1 1 SPI Flash Memory 64Mb SATA3 Connector SATAIII O 1 White S 17 SB 2 0 Ports USB_4_5 SGPIO Connector SATA SGPIO1 peaker Header SPEAKER1 CU Connector SCU PORT 2 3 Blue CU Connector SCU PORT 0 1 Blue p ROM header ROM1 Buzzer BUZZER1 USB 2 3 ystem Panel Header PANEL1 Intel C602 Chipset ATX Power Connector _ 1 Pi 2 0 27 C UJ N T oc 2 00 NT e Y O O 30 UD CNN header AUX PANEJ _ inteligent Platform Management Bus header PMB TPM Header mo __ 8 0001 4t BMCSMBHeader BMC_SMB1 _ 42 PCI Express 20 1 Slot PCIET White fom PCH PCI Express 3 0 x16 Slot PCIE2 Blue rom PCISit PCR White fromPCH ooo 45 PCI Express 3 0 x16 PCIE4 Blue rom Rear Fan Connector CPUBSPI 4 amp Express 3 0 x16 Slot PCIE6 Blue 0 RearFan Connector REAR FAN _
7. Use this to enable or disable the Onboard Debug Port LED The default value is Auto 78 3 3 6 USB Configuration USB 2 0 Controller Enabled USB 2 0 Controller Use this item to enable or disable the use of USB 2 0 controller Legacy USB Support Use this option to select legacy support for USB devices There are four configuration options Enabled Auto Disabled and UEFI Setup Only The default value is Enabled Please refer to below descriptions for the details of these four options Enabled Enables support for legacy USB Auto Enables legacy support if USB devices are connected Disabled USB devices are not allowed to use under legacy OS and UEFI setup when Disabled is selected If you have USB compatibility issues it is recommended to select Disabled to enter OS UEFI Setup Only USB devices are allowed to use only under UEFI setup and Windows Linux OS 79 3 3 7 Intel ME Subsystem Intel ME Subsystem Display information regarding Intel Management Engine 80 3 3 8 Clock Generator Configuration Aptio Setup Utility Copyright C 2011 American Megatren Spread Spectrum Disabled Spread Spectrum It is recommended to disable this option for better system stability 81 3 3 9 Storage Configuration SATA Mode AHCI SATA Mode Selection This item is for SATAIIL 0 1 SATAIL 2 3 and SATAII 4 5 ports Use this to select SATA mode Configuration options IDE
8. 100MHz D SUB Connector PCIExI 100MHz PCI PCISLOT SPI SPI FLASH 64Mb LPC BUS Nuvoton KB MS NCT6776 43 Chapter 2 Installation Before you install the motherboard study the configuration of your chassis to ensure that the motherboard fits into it EN2C606 4L D12 EN2C602 4L D12 EN2C602 D12 EN2C606 4L EN2C602 4L EN2C602 are dual socket motherboards that support Intel Xeon E5 2400 1400 Series Processors Please install a primary proces sor BootStrap Processor into CPU BSP1 socket and then install a non Primary Processor Application Processors into CPU AP1 socket a single CPU please install it into BSP1 socket framed by a square 2 1 Pre installation Precautions Take note of the following precautions before you install motherboard com ponents or change any motherboard settings 1 sure to unplug the power cord before installing or removing the motherboard Failure to do so may cause physical injuries to you and damages to motherboard com ponents 2 order to avoid damage from static electricity to the moth erboard s components NEVER place your motherboard directly on a carpet Also remember to use a grounded wrist strap or touch a safety grounded object before you handle the components 3 Hold components by the edges and do not touch the ICs 4 Whenever you uninstall any components place them on a grounded
9. 89 3 6 Boot Screen 90 3 7 Security SOlOBI aids 92 9 0 93 99 EVENT 94 4 Software Support 95 4 1 Install Operating System 95 4 2 Support CD Information 95 4 2 1 Running Support 95 4 2 2 Drivers 42 2 95 4 2 3 Utilities Menu sese 95 4 2 4 Contact Information 95 9 Troubleshooting 96 5 1 Troubleshooting Procedures 96 5 2 Technical Support Procedures 98 5 3 Returning Merchandise for Service 98 Chapter 1 Introduction Thank you for purchasing ASRock EN2C606 4L D12 EN2C602 4L D12 EN2C602 D12 EN2C606 4L EN2C602 4L EN2C602 motherboard a reliable motherboard produced under ASRock s consistently stringent qual ity control It delivers excellent performance with robust design conforming to ASRock s commitment to quality and endurance In this manual chapter 1 and 2 contains the introduction of the mother board and step by step hardware installation guide Chapter 3 and 4 con tains the configuration guide of BIOS setup and information of the Support CD Because
10. 45 44 43 42 52 PS2 Keyboard Mouse lt 8 2 ak USB2 0 T USBO B usp1 N LAN4 LAN3 LAN1 IPMI LAN OL BMC SMB1 00000 41 1 2 ATXPWR1 Aes OCOC DDR3 G2 64 bit 240 module 4 PSUSMB1 DDR3 A1 64 bit 240 pin module DDR3_B1 64 bit 240 pin module 26 7cm 10 5 in FRNT_FAN1 DDR3_G1 64 bit 240 pin module DDR3_F1 64 bit 240 pin module DDR3_E2 64 bit 240 pin module PCIE6 EN2C602 4L PCIE5 PCIE4 RoHS PCI3 MSRock PCIE2 CMOS PCIE1 Battery E 40 39 38 37 CPU FAN2 1 CPU FAN22 DDR3 C1 64 bit 240 pin module DDR3_C2 64 bit 240 pin module Intel C602 TR1 Dr Debug USB 6 USB 23 T Aux PANEL ns 36 35 34 26 ooo _ 11 CPU_FAN1_2 FRNT_FAN4 FRNTFAN3 FRNT FAN2 0000 COLL 64Mb BIOS 13 01 1 1 1 1 cLRCMOS2 RECOVERY1 scu scPiot 4 sara seror BUZZER1 UP ROM1 SPEAKER1 TE SCU PORT 0 SCU PORT 2 scu Pom scu eonr 3 SGPIO2 USB4 5 FRONT LED LAN34 tere 33 32 31 3029 28 27 2625 24 30 5cm 12in 15 16 18 19 20 21
11. B2 DDR3_C2 White SATA2 Connector SATAII 2 3 Blue ATA2 Connector SATAII 4 5 Blue Front Fan Connector FRNT FAN2 CU Connector SCU PORT 2 3 Blue CU Connector SCU PORT 0 1 Blue 27 CPU Fan Connector CPU FAN2 2 0 18 USB 2 0 Ports USB 6 Dr Debug PCI Express 3 0 x16 Slot PCIE3 Blue from CPU AP1 47 PCI Slot PCI1 White ite PCI Express 2 0 x1 Slot PCIE4 White from PCH Rear Fan Connector REAR 1 PCI Slot PCI2 White Buzzer BUZZER1 PCI Express 3 0 x16 Slot PCIE6 Blue from CPU SPI Flash Memory 64Mb PCI Express 3 0 x4 Slot PCIE7 White from CPU BSP1 Clear CMOS Pad CLRCMOS2 Rear Fan Connector REAR FAN2 PCI Express 3 0 x16 Slot PCIE5 Blue from CPU AP1 57 3 x 240 pin DDR3 DIMM Slots DDR3 G2 DDR3 F2 DDR3 E2 White 1356 Pin CPU Socket CPU AP1 Thermal Sensor header TR1 32 ES LN MN LEN NE M LM EU LM E LM CENE 46 LANE MN oa LN 52 ES LANE ES LM LN Gu ES 19 EN2C602 D12 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 7 33cm 13 FILE fl m DDR3 A1 64 bit 240 pin module DDR3 A2 64 bit 240 pin
12. DDR3 B1 64 bit 240 module DDR3 B2 64 bit 240 pin module H DDR3_C1 64 bit 240 pin module USB 2 0 LAN2 pem DDR3 C2 64 bit 240 pin module CPU FAN2 1 LAN3 DDR3_G2 64 bit 240 pin module DDR3_G1 64 bit 240 pin module O DDR3 F2 64 bit 240 pin module LAN1 DDR3 F1 64 bit 240 pin module DDR3 2 64 bit 240 pin module LAN Q Q PSUCALT SEL DDR3_E1 64 bit 240 pin module M m PSUSMB1 Fana PCIE7 AIGReck EN2C606 4L D12 _ 6 FRNT_FAN4 ay 5 PCIE5 ROWS T PCIEA coos V Cu attery i Intel PCIE3 C606 Mam 12 ami Super rr 5 vO 3 pet i FRONT LED LAN34 PCI wes Umm ur SCU PORT 0 SCU PORT 2 SCU PORT 4 SCU PORT 6 BMG AUX PANEL1 USB 4 5 23 2 UP ROMi SPEAKER Te Ta 1 Ir 1 EIOS ete IBID MEET SCU PORT 1 SCU PORT 3 SCU 5 SCU_PORT 7 44 43 42 41 40 39 38 37 36 353433 32 31 3029 28 27 26 25 24 412 1 06 10 11 20 21 22 23 14 7 12V Power Connector 12 1 Front Fan Connector FRNT 1 3 x 240 pin
13. FAN2 1 DDR3 G2 64 bit 240 pin module DDR3 G1 64 bit 240 pin module DDR3 F2 64 bit 240 pin module DDR3 F1 64 bit 240 pin module DDR3 E2 64 bit 240 pin module DDR3 E1 64 bit 240 pin module 33cm 13 in ATXPWR1 H DDR3 A1 64 bit 240 pin module FRNT FAN1 ATX12V1 DDR3 A2 64 bit 240 pin module DDR3 B1 64 bit 240 pin module DDR3 B2 64 bit 240 pin module DDR3 C1 64 bit 240 pin module DDR3 C2 64 bit 240 pin module PCIE7 EN2C602 4L D12 PCIEG PCIE5 RoHS PCIE4 cmos mz Intel C602 PCI2 Debu FRONT_LED_LAN34 TERI SCU PORT 0 SCU PORT 2 GUI mir ses amm 40 39 38 37 36 35 34 33 32313029 26 27 26 25 24 SATAIL 23 SATAIL4 5 I I JI dF 1 1 111 PSU PSU DATA SEL2 PSU ALT SEL3 PSUSMB1 FRNT_FAN3 FRNT_FAN4 FRNT gt 4121 Uuosog 10 11 13 14 15 16 20 21 22 23 17 Front Fan Connector 000 7 Front Fan Connector FRNT 1 3 x 240 pin DDR3 DIMM Slots DDR3_A2 DDR3
14. MSRock Super PCIE2 ie CMOS PCIE1 one Debug CEHJ 44 43 42 41 40 RECOVERY1 SCU SGPIO1 EH Scu scPio2 2 sara Ji T BUZZER1 ROM SPEAKER SATA SGPlO2 SCU PORTO SCU PORT 2 11 95845 scu Pom scufporT_3 P EL 39 3837 3635 34 3332 31 30 2928 27 23 FRNT_FAN1 CPU FRNT FAN4 FRNT FAN3 FRNT FAN2 meee LETT LIT E 3 X S 5 1 7 scu 7 cu 5 FRONT LED LAN34 1 30 5cm 12in 15 16 18 19 20 21 22 23 24 25 26 ATX PWR1 7 CPU Fan Connector CPU FAN1 2 _1 _M1 White White E CPU Fan Connector CPU FAN1 1 SPI Flash Memory 64Mb SATA3 Connector 0 1 White 17 SATA SGPIO Connector SATA SGPIO2 SB 2 0 Ports USB 4 5 peaker Header SPEAKER1 CU Connector SCU PORT 2 3 Black SCU Connector SCU PORT 0 1 Black Power Connector Pi CPU 27 EM W N D N 2 O E OI NI a e s Qo U x A 24 4T s 35 _ ES MN NE CNN LE CEN MN GN e ES LN CEN LM ES LM 2 NN net 56 d ES LN LN 25 EN2C602 4L 54 53 52 51 50 49 48 47 46
15. anti static pad or in the bag that comes with the components 5 When placing screws to secure the motherboard to the chassis please do not over tighten the screws Doing so may damage the motherboard 2 2 Screw Holes Place screws into the holes indicated by circles to secure the motherboard to the chassis 44 2 3 CPU Installation For the installation of Intel 1356 Pin CPU please follow the steps below 1356 Pin Socket Overview Before you insert the 1356 Pin CPU into the socket please check if the CPU surface is unclean or if there are any bent pins in the socket Do not force to insert the CPU into the socket if above situation is found Otherwise the CPU will be seriously damaged Step 1 Open the socket Step 1 1 Disengage the lever by pressing it down and sliding it out of the hook Step 1 2 Keep the lever positioned at about 135 degrees in order to flip up the load plate Step 2 Remove the PnP Cap Pick and Place Cap 45 1 It is recommended to use the cap tab to handle and avoid kicking off the PnP cap 2 This cap must be placed if returning the motherboard for after service Step 3 Insert the 1356 Pin CPU Step 3 1 Hold the CPU by the edge which is marked with a black line D Step 3 2 Locate Pin1 and the two orienta tion key notches orientation key notch alignment key f Pin1 Em Y b SES alignment key orientation key notch 1356 Pin CPU 1356 Pin Socke
16. module DDR3_B1 64 bit 240 pin module DDR3 B2 64 bit 240 pin module DDR3 C1 64 bit 240 pin module DDR3_C2 64 bit 240 pin module ntel C602 SCU_SGPIO1 2 3 4 5 6 saco as memi ATXPWR1 Keyboard Mouse e 5 9 OLI USB 2 0 Top USBO DDR3 G2 64 bit 240 pin module DDR3 G1 64 bit 240 pin module LANA DDR3_F2 64 bit 240 pin module DDR3 F1 64 bit 240 pin module IPMI DDR3 E2 64 bit 240 pin module LAN Q DDR3 E1 64 bit 240 pin module d PCIE7 PCIE6 PCIE5 nd RHS CMOS BUZZERI 4 Battery BIOS PCIE3 P 2 CLRCMOS2 P 1 Debug USB 6 BMC _ AUX PANEL1 ROM TT Tia seem acy A ABA 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 SCU PORT 0 SCU PORT 2 Jag alc 731 Scu PORT SCU_PORT 3 25 24 PSU PSU SEL2 PSU ALT SELS PSUSMB1 FRNT FRNT_FAN4 M2 2 3 SATAIL4 5 FRNT_FAN2 1 06 10 11 20 21 22 23 20 7 12V Power Connector 12 1 Front Fan Connector FRNT 1 3 x 240 pin DDR3 DIMM Slots
17. 182574L PCIEXL 100MHz SPI FLASH BMC ASPEED D SUB Connector AST2300 PCIEx1 100MHz COM Port Connector Realtek PHY 8211E LPC BUS Nuvoton NCT6776 38 EN2C602 4L D12 VRD 12 VRD 12 on Board on Board Intel Processor Intel Processor DDR3 1066 1333 1600 DDR3 2066 1333 1600 CH A QPI PORT 8 0GT s SNB EN IVB EN SNB EN IVB EN DDR3 1066 1333 1600 C 1066 1333 1 600 E LGA 1356 Pin Socket LGA 1356 Pin Socket CPU DDR3 1066 1333 1600 CPU 8 CH C 1066 1333 1600 S PCIE Gen3 x16 SLOT x16 Jg PCIE Gen3 x16 SLOT x8 0 100MHz 5 PCIE Gen3 BUS PCIE Gen3 X16 SLOT X16 PCIE Gen2 x1 Slot x1 1 PCIE Gen3 X4 SLOT 4 100MHz LAN 2 SE 100MHz LAN3 Inte 182574L POTERI SCU miim C602 chipset only SATA 2 0 Inte 182574L INTEL 100MHz PCI PCI SLOTI SATA3 C602 M 19230 CIES 100 MH PCH PCI PCI SLOT2 SPI FLASH SPI pus D SUB Connector 1 100MHz LPC BUS Nuvoton KB MS COM Port Connector NCT6776 Realtek PHY 8211E SPI FLASH USB USB 2 0 x7 PORTS 39 EN2C602 D12 VRD 12 on Board VRD 12 on Boa
18. AN2 7 D Sub Port VGA 4 IPMI LAN Port 8 PS 2 Keyboard Port Purple There are two LEDs on each LAN port Please refer to the table below for the LAN port LED indications ACT LINK SPEED LAN Port LAN2 LED LED LED Indications Activity Link LED SPEED LED Status Description No Link 10Mbps connection Blinking Data Activity 100Mbps connection 100Mbps connection 1Gbps connection LAN Port LAN Port LAN1 LAN3 IPMI LAN SPEED ACT LINK LED Indications LED LED Activity Link LED SPEED LED 37 1 6 Block Diagram EN2C606 4L D12 VRD 12 on Board Intel Processor DDR3 1066 1333 1600 Intel Processor DDR3 1066 1333 1600 CHA SNB EN IVB EN SNB EN IVB EN annen DDR3 1066 1333 1600 1066 1333 1600 LGA 1356 Pin Socket LGA 1356 Pin Socket CPU_BSP1 CPU_AP1 DDR3 1066 1333 1600 PCIE Gen3 x16 SLOT x16 PCIE Gen3 x16 SLOT x8 100MHz PCIE Gen3 BUS PCIE Gen3 X16 SLOT X16 PCIE Gen2 x1 Slot x1 PCIE Gen3 X4 SLOT x4 100MHz ING uob LAN2 ses BOE hte 1825741 100MHz helt 121825741 SCU LE C606 chipset SAS 8 ports on SCU LANA Inte 182574L INTEL 100MHz PCI PCI SLOTI C606 5 2 19230 100MHz PCH PCT PCI SLOT2 Inte
19. ASRock EN2C606 4L D12 EN2C602 4L D12 EN2C602 D12 EN2C606 4L EN2C602 4L EN2C602 User Manual Version 1 0 Published Jan 2013 Copyright 2013 ASRock INC All rights reserved Copyright Notice No part of this manual may be reproduced transcribed transmitted or translated in any language in any form or by any means except duplication of documentation by the purchaser for backup purpose without written consent of ASRock Inc Products and corporate names appearing in this manual may or may not be regis tered trademarks or copyrights of their respective companies and are used only for identification or explanation and to the owners benefit without intent to infringe Disclaimer Specifications and information contained in this manual are furnished for informa tional use only and subject to change without notice and should not be constructed as a commitment by ASRock ASRock assumes no responsibility for any errors or omissions that may appear in this manual With respect to the contents of this manual ASRock does not provide warranty of any kind either expressed or implied including but not limited to the implied warran ties or conditions of merchantability or fitness for a particular purpose In no event shall ASRock its directors officers employees or agents be liable for any indirect special incidental or consequential damages including damages for loss of profits loss of business loss of data interruption of bu
20. D12 EN2C602 D12 Link Speed This allows you to select PCIE3 Link Speed PCIE5 Link Speed This allows you to select PCIE5 Link Speed PCIE6 Link Speed This allows you to select PCIE6 Link Speed PCIE7 Link Speed This allows you to select PCIE7 Link Speed 74 For EN2C606 4L EN2C602 4L EN2C602 PCIE2 amp 4 Link Width This allows you to select PCIE2 amp PCIEA Link Width PCIE2 amp 4 Link Speed This allows you to select PCIE2 amp PCIEA Link Speed PCIE5 Link Speed This allows you to select PCIE5 Link Speed PCIE6 Link Speed This allows you to select PCIE6 Link Speed 75 Intel Quickpath Interconnect Configuration Isoc Use this to enable disable Isoc It is recommended to select En abled QPI Link Speed Mode This allows you to select Link Speed Mode It is recommend ed to select Auto QPI Link Frequency Select This allows you to select Link Frequency Memory Configuration Memory Mode Select the mode for memory initialization Independent Independent channel mode Mirroring The memory subsystem writes identical data to two channels simultaneously Identical memory modules should be installed in the two channels closest to the processor Lock Step The two channels closest to the processor are com bined to form a single channel Memory modules must be iden tical in size speed and technology in corresponding slots Sparing This mode occur
21. DDR3 A2 DDR3 B2 DDR3 C2 White 17 SATA2 Connector 5 2 3 Blue 27 CPU Fan Connector CPU FAN2 2 CPU Fan Connector CPU FAN2 1 1356 Pin CPU Socket CPU BSP1 3 21 UP ROM Header UP ROM1 BMC ROM USB 2 0 Ports USB 6 Dr Debug PCI Express 3 0 x16 Slot PCIE3 Blue from CPU AP1 Thermal Sensor header TR1 s PCI Slot PCM White PCI Slot PCI2 White 5 COM Port Header COM2 47 Clear CMOS Pad CLRCMOS2 32 Pesi M oa LINE ES LEE DEN LE CNN LN CEN do CEN LN LN E LO EE 56 NN LN 22 EN2C606 4L 57 56 55 54 53 52 51 50 49 48 47 46 45 PS2 PS2 Keyboard Mouse ATXPWR1 LETTI lt 8 gt 0882 01 USBO i B usB1 N LAN4 LAN3 O O LAN1 IPMI LAN LL DDR3_G2 64 bit 240 pin module EOS DDR3 G1 64 bit 240 pin module DDR3_A1 64 bit 240 pin module DDR3 B1 64 bit 240 pin module 26 7cm 10 5 in DDR3 C1 64 bit 240 module m DDR3_C2 64 bit 240 pin module CPU FAN2 1 CPU FAN2 2 been DDR3 F1 64 bit 240 pin module DDR3 E2 64 bit 240 pin module PCIEG EN2C606 4L 5 REAR_FANZ 64Mb BIOS 5 Intel C606 PCIE4 RoHS PCI3
22. DDR3 DIMM Slots DDR3 A2 DDR3 B2 DDR3 C2 White 17 SATA2 Connector 5 2 3 Blue SCU Connector SCU PORT 6 7 Black SCU Connector SCU PORT 4 5 Black S CU Connector SCU PORT 2 3 Black 27 SCU Connector SCU PORT 0 1 Black SATA SGPIO Connector SATA SGPIO2 SCU SGPIO Connector SCU SGPIO1 SATA SGPIO Connector SATA SGPIO1 SCU SGPIO Connector SCU SGPIO2 CPU Fan Connector CPU FAN2 2 CPU Fan Connector CPU FAN2 1 1356 Pin CPU Socket CPU BSP1 3 15 UP ROM Header BMC ROM SB 2 0 Ports USB 6 47 Dr Debug PCI Slot PCI2 White PCI Express 3 0 x16 Slot PCIE3 Blue from CPU AP1 Thermal Sensor header TR1 Clear CMOS Pad CLRCMOS2 PCI Express 2 0 x1 Slot PCIE4 White from PCH ite ite ite 3 _5 Intelligent Plattorm Management Bus header IPMB 1 TPM Header TPM1 COM Port Header COM2 57 1356 Pin CPU Socket CPU AP1 32 NM LL MN LE CAN ES 40 CEN LEE CNN _ CNN dod CN LN o E 52 ES LN ES LN LEN LI LN LONE 6e 16 EN2C602 4L D12 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 52 52 Keyboard Mouse 518 gt USB20 T USBO LAN3 LANT IPMI LAN BMC ROM 41 CPU FAN1 2 FAN1 1 ATX12V2 Q CPU FAN2 2 CPU
23. IMM 49 2 6 Expansion Slots PCI and PCI Express Slots 51 2 7 Jumpers 53 2 8 Onboard Headers and Connectors 54 2 9 Driver Installation Guide 63 2 10 Hot Plug for Hard Disk Drives 64 3 UEFISETUP UTILITY 2 6 65 3 1 65 3 14 UEFI Menu 65 3 1 2 Navigation Keys 66 3 2 Main Screen icto ia uat 67 3 3 Advanced 68 3 9 1 ACPI Configuration itt oett 69 3 3 2 WHEA Configuration 71 3 3 3 CPU ConfgulrallOll ui tari e 72 3 3 4 North Bridge Configuration 74 3 3 5 South Bridge Configuration 78 3 3 6 USB 79 3 3 7 Intel ME Subsystem 80 3 3 8 Clock Generator Configuration 81 3 3 8 Storage Configuration 82 3 3 10 Super IO Configuration 84 3 3 11 Serial Port Console Redirection 85 3 3 12 Voltage COMMON 86 3 4 Hardware Health Event Monitoring Screen 87 3 5 Server
24. Mode AHCI Mode RAID Mode and Disabled The default value is AHCI Mode AHCI Advanced Host Controller Interface supports NCQ and other new features that will improve SATA disk performance but IDE mode does not have these advantages SATA Aggressive Link Power Management Use this item to configure Aggressive Link Power Management Hard Disk S M A R T Use this to enable or disable S M A R T Self Monitoring Analy sis and Reporting Technology Marvell 9230 SATA3 M0 M3 Operation For EN2C606 4L D12 EN2C602 4L D12 EN2C602 D12 Only This item is for SATAIII MO M1 and SATAIIL M2 ports Use this to enable or disable Marvell SATA3 operation mode Bootable Marvell SATAIII Control Use this to select onboard Marvell SATAIII Option ROM SCU Devices Use this to enable or disable SCU devices 82 Onboard SCU Oprom Driver Use this to enable or disable Onboard Marvell Option ROM If Option ROM is disabled you cannot use the SATA de vices connected to the Marvell SATA3 controller as Boot Device Marvell 9220 SATA3 0 1 Operation For EN2C606 4L EN2C602 4L EN2C602 Only This item is for SATAIII MO 1 ports Use this to enable or dis able Marvell SATA3 operation mode Bootable Marvell SATAIII Control Use this to select onboard Marvell SATAIII Option ROM SCU Devices Use this to enable or disable SCU devices Onboard SCU Oprom Driver Use this to enable or disable Onboard Marvell Optio
25. NTROL FAN SPEED 12V Please connect the CPU fan cable to the connector and match the black wire to the ground pin GND 12V CPU_FAN_SPEED FAN SPEED CONTROL FAN SPEED CONTROL CPU SPEED 12 GND GND 12V CPU FAN SPEED FAN SPEED CONTROL Though this motherboard provides a 4 Pin CPU fan Quiet Fan connector 3 Pin CPU fans can still work successfully even with out the fan speed control function If you plan to connect a 3 Pin CPU fan to the CPU fan connector on this motherboard please connect it to Pin 1 3 3 pin CPU FAN1 2 see p 15 18 21 see p 24 27 30 3 CPU 2 2 see p 12 15 18 see p 25 28 31 Pin 1 3 Connected lt 3 Pin Fan Installation FAN SPEED 12V GND GND 12V CPU SPEED CPU FAN SPEED 12V GND GND 12V CPU SPEED 59 ATX Power Connector 12 Please connect an pow 24 pin ATXPWR1 see p 15 18 21 24 27 30 A IDOL 10001 0 er supply to this connector Though this motherboard provides a 24 pin ATX power connector it can still work if you adopt a traditional 20 pin ATX power supply To use a 20 pin ATX power supply please plug your power supply along Pin 1 and Pin 13 20 Pin ATX Power Supply Installation Though this motherboard provides an 8 pin ATX 12V power con nector it can still work if you adopt a tradition
26. ST2300 T LANI Inte182574L Intel Processor SNB EN IVB EN LGA 1356 Pin Socket CPU BSP1 ING Intel Processor SNB EN IVB EN PI PORT 8 0GT s LGA 1356 Pin Socket CPU 100MHz gu 9 PCIE Gen3 BUS PCIEx1 100MHz PCIEx1 100MHz PCIEx1 100MHz 100MHz 100MHz PCIEx2 100MHz PCIEx1 100MHz DDR3 1066 1333 1600 DDR3 1066 1333 1600 DDR3 1066 1333 1600 PCIE Gen3 x16 Slot x16 PCI E Gen3 X4 SLOT X4 PCI E Gen3 X16 SLOT 16 8 PCI E 3 X16 SLOT x8 X0 SATA SATA BUS INTEL 1 5 SCU PORT 0 SCU PORT 4 C606 Scu SCU PORT 1 SCU PORT 5 SCU PORT 2 SCU PORT 6 PCH SCU PORT 3 SCU PORT 7 C606 chipset SAS x 8 ports on SCU controller PCI PCISLOT SPI SPI FLASH 64Mb LPC BUS Nuvoton KB MS NCT6776 41 EN2C602 4L VRD 12 on Board VRD 12 on Board DDR3 1066 1333 1600 Intel Processor Intel Processor SNB EN IVB EN RT 8 SNB EN IVB EN DDR3 1066 1333 1600 DDR3 1066 1333 1600 LGA 1356 Pin Socket LGA 1356 Pin Socket DDR3 1066 1333 1600 UB DDR3 1066 1333 1600 1066 1333 1600 PCIE Gen3 x16 Slot 16
27. _ _ _ 8x240pin DDREDIMMSiis ODRGLDDRSFI DORS EZ Bue 0 1 2 0 DDR3 DIMM Slots _ 1356 CPU Socket AP O O O cPUFanComedor CPU 1 FANL2 _ 31 1 5 I O Panel EN2C606 4L D12 1 PS 2 Mouse Port Green 6 LAN RJ 45 Port LAN3 2 Serial Port COM1 7 LAN RJ 45 Port 9 LAN RJ 45 Port LAN2 8 USB 2 0 Ports 05801 4 IPMI LAN Port 9 D Sub Port VGA 5 LAN RJ 45 Port LAN1 10 PS 2 Keyboard Port Purple There are two LEDs on each LAN port Please refer to the table below for the LAN port LED indications ACT LINK SPEED LAN Port LAN2 LED LED LED Indications Activity Link LED SPEED LED Status Description Description No Link 10Mbps connection Blinking Data Activity 100Mbps connection 100Mbps connection 1Gbps connection LAN Port LAN Port LAN1 LAN3 LAN4 IPMI LAN SPEED ACT LINK LED Indications LED LED Activity Link LED SPEED LED 10Mbps connection Blinking Data Activity 100Mbps connection 100Mbps connection 1Gbps connection LAN Port 32 EN2C602 4L D12 1 PS 2 Mouse Port Green 6 LAN RJ 45 Port LAN3 2 Serial Port COM1 7 LAN RJ 45 Port 9 LAN RJ 45 Port LAN2 8 USB 2 0 Ports 05801 4 IPMI LAN Port 9 D Sub Port VGA 5 LAN RJ 45 Port LAN1 10 PS 2 Keyboard Port Purple There are two LEDs on each LAN port Please refer to the table b
28. a Scrambling Enable this feature to ensure data security and integrity Device Tagging The ability to replace a device with excessive corrected error Once a device is tagged errors can only be detected and not cor rected Thermal Throttling Use this automatic memory throttling feature to reduce power consumption The default value is CLTT Closed Loop Thermal Throttling DIMM Information Display DIMM information 77 3 3 5 South Bridge Configuration Aptio Setup Utility Copyright C 2011 American Megatrends Inc Restore on AC Power Loss Last State Restore on AC Power Loss This allows you to set the power state after an unexpected AC power loss If Power Off is selected the AC power remains off when the power recovers If Power On is selected the AC power resumes and the system starts to boot up when the power recovers Deep Sleep Mobile platforms support Deep S4 S5 in DC only and desktop platforms support Deep S4 S5 in AC only The default value is Disabled Onboard LAN1 This allows you to enable or disable the Onboard LAN1 Onboard LAN2 USBO01 This allows you to enable or disable the Onboard LAN2 05 01 Onboard LAN3 For EN2C606 4L D12 EN2C602 4L D12 EN2C606 4L EN2C602 4L Only This allows you to enable or disable the Onboard LAN3 Onboard LAN4 For EN2C606 4L D12 EN2C602 4L D12 EN2C606 4L EN2C602 4L Only This allows you to enable or disable the Onboard LAN4 Onboard Debug Port LED
29. ake sure to disconnect the power supply before add ing or removing DIMMs or system components Step 1 Unlock a DIMM slot by pressing the retaining clips outward Step 2 Align a DIMM on the slot such that the notch on the DIMM matches the break on the slot 49 lt notch lt lt break The DIMM only fits in one correct orientation It will cause per manent damage to the motherboard and the DIMM if you force the DIMM into the slot at incorrect orientation Step 3 Firmly insert the DIMM into the slot until the retaining clips at both ends fully snap back in place and the DIMM is properly seated 50 2 6 Expansion Slots PCI and Express Slots EN2C606 4L D12 EN2C602 4L D12 EN2C602 D12 There are 2 PCI slots and 5 PCI Express slots on the motherboard PCI slot The and PCI2 slot are used to install expansion cards that have 32 bit PCI interface PCIE slots PCIE7 PCIE 3 0 x4 slot is used for PCI Express x4 lane width cards PCIE4 PCIE 2 0 x1 slot is used for PCI Express x1 lane width cards such as a Gigabit LAN card or SATA2 card etc 5 PCIE 3 0 x16 slot are used for PCI Express x8 lane width graphics cards and PCIE6 PCIE 3 0 x16 slot are used for PCI Express x16 lane width graphics cards Please note that PCIE3 and PCIE5 are available ONLY when the second CPU CPU AP1 is installed EN2C606 4L EN2C602 4L EN2C602 There are 1 PCI slot and 5 PCI Express slots on the
30. al 4 pin ATX 12V power supply To use a 4 pin ATX power supply please plug your power supply along Pin 1 and Pin 5 8 4 Pin ATX 12V Power Supply Installation ATX 12V Power Please connect an ATX 12V Connector For EN2C60xD12 Series power supply to this connec 8 pin ATX12V2 tor see p 15 18 21 8 pin ATX12V1 15 18 21 MENT id 001 4 1 12 THU Please connect an ATX 12V Connector power supply to this connec For EN2C60x Series gt tor 8 pin ATX12V 1 see p 21 24 27 8 pin ATX12V1 see p 24 27 30 A 60 RRXD1 Serial port Header 9 pin COM2 see p 16 19 22 25 28 31 DDSR 1 CCTS 1 1 DDCD 1 Intelligent Platform GND connect Management Bus header um 4 pin IPMB 1 SCL see p 16 19 22 25 28 31 IMBRE Thermal Sensor header TRI TR 3 pin TR1 see p 16 19 22 25 28 31 1 GND Clear CMOS Pad CLRCMOS2 see p 16 19 22 24 27 30 61 This COM2 header supports a serial port module This 4 pin connector is used to provide a cabled base board or front panel connec tion for value added features and 3rd party add in cards such as Emergency Man agement cards that provide management features using the IPMB Please connect the thermal sensor cable to either pin 1 2 or pin 2 3 a
31. ar Panel 1x RJ45 Dedicated IPMI LAN port LAN Ports with LED ACT LINK LED and SPEED LED Lan port EN2C602D12 2x RJ45 EE ae Ethernet LAN ports 1 x RJ45 Dedicated IPMI LAN port LAN Ports with LED ACT LINK LED and SPEED LED Serial port COM1 Type AUSB 1 2 0 port USB 2 0 2 Each support 2 USB 2 0 1x COM from 80 debug 1 port LED Auxiliary panel header Au Front panel 000000 Connector 1 L pin Thermal sensor 1 header 8 8 x 4 pin 2 x 3 pin CPU fan header have 3 pin and 4 pin ones Two types couldn t be used at the same time 1 include chassis intrusion location button amp LED front LAN LED Fan header PSUSMB header Internal Dr Debug Connector with LED 1 ATX power 1 24 pin 2 8 pin Plug and Play PnP ACPI 1 1 Compliance Wake Up Events System BIOS BIOS type Supports jumperfree SMBIOS 2 3 1 Support DRAM Voltage Multi adjustment CPU Temperature Sensing Temperature System Temperature Sensing CPU Rear Front Fan Tachometer Fan CPU Quiet Fan Allow Chassis Fan Speed Auto Adjust by CPU Temperature Monitor CPU Rear Front Fan Multi Speed Control Voltage Monitoring CPU1 2 DRAM 1 2 Water VTT1 2 VCCSA1 2 9 3V 5V 12V 1 05V_PCH 3VSB 5VSB Microsoft Windows Server 2008 2008 Supra Qe R2 Linux compliant Operation temperature 10 35 Non Temperature operation temperature E
32. b Port VGA 5 LAN RJ 45 Port LAN1 10 PS 2 Keyboard Port Purple There are two LEDs on each LAN port Please refer to the table below for the LAN port LED indications LAN Port LAN2 LED Indications Activity Link LED Status Description Description No Link 10Mbps connection 1 g Data Activity OOMbps connection n 100Mbps connection 1Gbps connection LAN Port LAN Port LAN3 IPMI LAN SPEED ACT LINK LED Indications LED LED Activity Link LED SPEED LED ACT LINK SPEED LED LED tatus Description tatus ff No Link f Blinking Data Activity ff n 100Mbps connection Green SAN Pori 35 EN2C602 4L 1 PS 2 Mouse Port Green 6 LAN RJ 45 Port LAN3 2 Serial Port COM1 7 LAN RJ 45 Port 9 LAN RJ 45 Port LAN2 8 USB 2 0 Ports 05801 4 IPMI LAN Port 9 D Sub Port VGA 5 LAN RJ 45 Port LAN1 10 PS 2 Keyboard Port Purple There are two LEDs on each LAN port Please refer to the table below for the LAN port LED indications ACT LINK SPEED LAN Port LAN2 LED LED LED Indications Activity Link LED Status Description tatus No Link Data Activity range 100Mbps connection Green LAN Port LAN Port LAN1 LAN3 IPMI LAN SPEED ACT LINK LED Indications LED LED Activity Link LED SPEED LED 36 EN2C602 1 PS 2 Mouse Port Green 5 LAN RJ 45 Port LAN1 2 Serial Port COM1 6 USB 2 0 Ports 05801 9 LAN RJ 45 Port L
33. ble OEM Logo The default value is Enabled AddOn ROM Display Use this option to adjust AddOn ROM Display If you enable the option Full Screen Logo but you want to see the AddOn ROM information when the system boots please select Enabled Con figuration options Enabled and Disabled The default value is Enabled Boot From Onboard LAN Use this item to enable or disable the Boot From Onboard LAN feature Boot From PCIE PCI LAN Use this item to enable or disable the Boot From PCIE PCI LAN feature 91 3 7 Security Screen In this section you may set or change the supervisor user password for the system For the user password you may also clear it Supervisor Password 92 3 8 Exit Screen Aptio Setup Utility Copyright C 2011 American Megatrends ne Save Changes and Exit Save Changes and Exit When you select this option the following message Save con figuration changes and exit setup will pop out Select Yes to save the changes and exit the UEFI SETUP UTILITY Discard Changes and Exit When you select this option the following message Discard changes and exit setup will pop out Select Yes to exit the UEFI SETUP UTILITY without saving any changes Discard Changes When you select this option the following message Discard changes will pop out Select Yes to discard all changes Load UEFI Defaults Load UEFI default values for all the setup questions F9 key can be used for this
34. date information Advanced For advanced system configurations H W Monitor Displays current hardware status Boot For configuring boot settings and boot priority Security For security settings Save amp Exit Exit the current screen or the UEFI Setup Utility Server Mgmt For managing the server Event Logs For event log configuration 65 3 1 2 Navigation Keys Use lt lt gt key or lt gt key to choose among the selections on the menu bar and use lt gt key or gt key to move the cursor up or down to select items then press Enter to get into the sub screen You can also use the mouse to click your required item Please check the following table for the descriptions of each navigation key To change option for the selected items 66 3 2 Main Screen When you enter the UEFI SETUP UTILITY the Main screen will appear and display the system overview 67 3 3 Advanced Screen In this section you may set the configurations for the following items ACPI Configuration WHEA Configuration CPU Configuration North Bridge Con figuration South Bridge Configuration USB Configuration ME Subsystem Clock Generator Configuration Storage Configuration Super IO Configura tion Serial Port Console Redirection and Voltage Control gt gt ACPI Configuration Setting wrong values in this section may cause the system to malfunction Instant Flash Instant Flash is a UEFI flash utility emb
35. edded in Flash ROM This convenient update tool allows you to update system UEFI without entering operating systems first like MS DOS or Win dows Just save the new UEFI file to your USB flash drive flop py disk or hard drive and launch this tool then you can update your UEFI only in a few clicks without preparing an additional floppy diskette or other complicated flash utility Please be noted that the USB flash drive or hard drive must use FAT32 16 12 file system If you execute Instant Flash utility the utility will show the UEFI files and their respective information Select the proper UEFI file to update your UEFI and reboot your system after the UEFI update process is completed 68 3 3 1 ACPI Configuration Enabled Suspend Mode Use this item to enable or disable the highest ACPI Sleep state S1 If enabled the system enters S1 level when the SUSPEND button is pressed ACPI HPET Table Use this item to enable or disable ACPI HPET Table The default value is Enabled PS 2 Keyboard Power On Use this item to enable or disable PS 2 keyboard to turn on the system from the power soft off mode PCI Devices Power On Use this item to enable or disable PCI devices to turn on the sys tem from the power soft off mode Ring In Power On Use this item to enable or disable Ring In signals to turn on the system from the power soft off mode RTC Alarm Power On Use this item to enable or disable RTC Real Time Clock to p
36. elect CPU PLL 1 Voltage The default value is Auto PLL 2 Voltage Use this to select CPU PLL 2 Voltage The default value is Auto VTT 1 Voltage Use this to select VTT 1 Voltage The default value is Auto VTT 2 Voltage Use this to select VTT 2 Voltage The default value is Auto PCH Voltage Use this to select PCH Voltage The default value is Auto 86 3 4 Hardware Health Event Monitoring Screen In this section it allows you to monitor the status of the hardware on your system including the parameters of the CPU temperature motherboard temperature and the critical voltage CPU Fan 1 Setting CPU 1 1 Setting This allows you to set the speed of CPU Fan1 1 The default value is Full On CPU 1 2 Setting This allows you to set the speed of CPU Fan1 2 The default value is Full On CPU Fan2 1 Setting This allows you to set the speed of CPU Fan2 1 The default value is Full On CPU Fan2 2 Setting This allows you to set the speed of CPU Fan2 2 The default value is Full On REAR Fan1 Setting This allows you to set the speed of REAR Fan1 The default value is Full On REAR Fan2 Setting This allows you to set the speed of REAR Fan1 The default value is Full On FRNT Fan1 Setting This allows you to set the speed of FRNT Fan1 The default value is Full On 87 FRNT Fan2 Setting This allows you to set the speed of FRNT Fan2 The default value is Full On FRNT Fan3 Setting This allow
37. elow for the LAN port LED indications ACT LINK SPEED LAN Port LAN2 LED LED LED Indications Activity Link LED SPEED LED Status Description Description ff No Link 10Mbps connection 1 inking Data Activity OOMbps connection n 100Mbps connection 1Gbps connection LAN Port LAN Port LAN1 LAN3 LAN4 IPMI LAN SPEED ACT LINK LED Indications LED LED Activity Link LED SPEED LED tatus Description Status Description ff No Link Off 10 connection Off 1 Blinking Data Activity 100Mbps connection n 100Mbps connection 1Gbps connection LAN Port 33 EN2C602 D12 1 PS 2 Mouse Port Green 5 LAN RJ 45 Port LAN1 2 Serial Port COM 6 USB 2 0 Ports 05801 9 LAN RJ 45 Port LAN2 7 D Sub Port VGA 4 IPMI LAN Port 8 PS 2 Keyboard Port Purple There are two LEDs on each LAN port Please refer to the table below for the LAN port LED indications ACT LINK SPEED LAN Port LAN2 LED Indications LED Activity Link LED SPEED LED tatus Description Status ff No Link 10Mbps connection Blinking Data Activity 100Mbps connection n 100Mbps connection 1Gbps connection LAN Port LAN Port LAN1 IPMI LAN SPEED ACT LINK LED Indications LED LED Activity Link LED SPEED LED ee 34 EN2C606 4L 1 PS 2 Mouse Port Green 6 LAN RJ 45 Port LAN3 2 Serial Port COM1 7 LAN RJ 45 Port 9 LAN RJ 45 Port LAN2 8 USB 2 0 Ports 05801 4 IPMI LAN Port 9 D Su
38. en follow the installation wizard to install it 4 2 4 Contact Information If you need to contact ASRock or want to know more about ASRock you re welcome to visit ASRock s website at http www asrock com or you may contact your dealer for further information 95 Chapter 5 Troubleshooting 5 1 Troubleshooting Procedures Follow the procedures below to troubleshoot your system Always unplug the power cord before adding removing or changing any hardware components Failure to do so may cause physical injuries to you and damages to motherboard components 1 Disconnect the power cable and check whether the PWR LED is off 2 Unplug all cables connectors and remove all add on cards from the motherboard Make sure that the jumpers are set to default settings 3 Confirm that there are no short circuits between the motherboard and the chassis 4 Install a CPU and fan on the motherboard then connect the chassis speaker and power LED If there is no power 1 Confirm that there are no short circuits between the motherboard and the chassis 2 Make sure that the jumpers are set to default settings 3 Check the settings of the 115V 230V switch on the power supply 4 Verify if the battery on the motherboard provides 3VDC Install a new battery if it does not If there is no video 1 Try replugging the monitor cables and power cord 2 Check for memory errors If there are memory errors 1 Verify that the DIMM m
39. h external detection equipment such as a chassis intrusion detection sensor or a microswitch When this function is activated if any chassis component movement occurs the sensor will immediately detect it and send a signal to this header and the system will then record this chassis intrusion event The default setting is set the CASEOPEN and GND pin this function is off D Locator LED 6 pin LOCATOR This header is for the locator switch and LED on the front panel Speaker Header 4 SPEAKER1 see p 16 19 22 24 27 30 Front and Rear Fan Connectors 4 pin FRNT FAN1 4 pin FRNT FAN2 4 pin FRNT FAN3 4 pin FRNT FAN4 see p 15 18 21 4 FRNT FAN2 4 FAN3 4 4 see p 24 27 30 4 REAR_FAN1 see p 16 19 22 25 28 31 4 REAR_FAN2 see p 16 19 22 4 REAR_FAN2 see p 25 28 31 Please connect the speaker DUMMY to this header Please connect the fan cables to the fan connectors and match the black wire to FAN SPEED CONTROL the ground pin fans sup ports Fan Control GND 12V CPU_FAN_SPEED FAN SPEED CONTROL GND 12V CPU_FAN_SPEED FAN SPEED CONTROL FAN SPEED CONTROL CPU SPEED 12 GND FAN SPEED CONTROL 58 CPU Fan Connectors 4 pin CPU 1 1 see p 15 18 21 see p 24 27 30 4 pin CPU FAN2 1 see p 15 18 21 see p 25 28 31 FAN SPEED CO
40. ired drivers Therefore the drivers you install can work properly 63 2 10 Hot Plug for Hard Disk Drives This motherboard supports Hot Plug for HDDs in AHCI RAID mode A What is Hot Plug If the HDDs are NOT set for RAID it is called Hot Plug for the action to insert and remove the HDDs while the system is still powered on and in working condition However please note that it cannot perform Hot Plug if the OS has been installed into the HDD 64 Chapter 3 UEFI SETUP UTILITY 3 1 Introduction This section explains how to use the UEFI SETUP UTILITY to configure your system The UEFI chip on the motherboard stores the UEFI SETUP UTILITY You may run the UEFI SETUP UTILITY when you start up the computer Please press F2 or Del during the Power On Self Test POST to enter the UEFI SETUP UTILITY otherawise POST will continue with its test routines If you wish to enter the UEFI SETUP UTILITY after POST restart the sys tem by pressing lt Ctl gt Alt Delete or by pressing the reset button on the system chassis You may also restart by turning the system off and then back on Because the UEFI software is constantly being updated the following UEFI setup screens and descriptions for reference purpose only and they may not exactly match what you see on your screen 3 1 1 UEFI Menu Bar The top of the screen has a menu bar with the following selections Main For setting system time
41. motherboard PCI slot The PCI slot is used to install expansion cards that have 32 bit PCI interface PCIE slots PCIE5 PCIE 3 0 x4 slot is used for PCI Express x4 lane width cards PCIE1 PCIE 2 0 x1 slot is used for PCI Express x1 lane width cards such as a Gigabit LAN card or SATA2 card etc PCIE6 PCIE 3 0 x16 slot is used for PCI Express x8 lane width graphics cards PCIE2 and PCIE4 PCIE 3 0 x16 slot are used for PCI Express x16 lane width graphics cards 51 In single VGA card mode it is recommended to install PCI Express x16 graphics card on slot Installing an expansion card Step 1 Before installing an expansion card please make sure that the power supply is switched off or the power cord is unplugged Please read the documentation of the expansion card and make necessary hardware settings for the card before you start the installation Step 2 Remove the system unit cover if your motherboard is already installed in a chassis Step 3 Remove the bracket facing the slot that you intend to use Keep the screws for later use Step 4 Align the card connector with the slot and press firmly until the card is completely seated on the slot Step 5 Fasten the card to the chassis with screws Step 6 Replace the system cover 52 2 Jumpers Setup The illustration shows how jumpers are setup When the jumper cap is placed on pins the jumper is Short If no jumper cap Vu is placed on pi
42. n ROM If Option ROM is disabled you cannot use the SATA de vices connected to the Marvell SATA3 controller as Boot Device We recommend to use Intel C606 C602 SATA ports SA 0 1 SATAII 2 3 and SATAII 4 5 for your bootable devices This will minimum your boot time and get the best performance But if you still want to boot from the Marvell SATA3 controller you can enable it from the 83 3 3 10 Super IO Configuration Serial Port 1 Configuration Use this item to configure the onboard serial port 1 Serial Port 2 Configuration Use this item to configure the onboard serial port 2 84 3 3 11 Serial Port Console Redirection Disabled Console Redirection Use this option to enable or disable Console Redirection Console Redirection Settings Use this option to configure Console Redirection Settings 85 3 3 12 Voltage Control CPU 1 Core Voltage 0 870 0 870 0 855V CPU 1 Core voltage Use this to select CPU 1 Core voltage The default value is Auto CPU 2 Core voltage Use this to select CPU 2 Core voltage The default value is Auto VCCSA 1 Voltage Use this to select VCCSA 1 Voltage The default value is Auto VCCSA 2 Voltage Use this to select VCCSA 2 Voltage The default value is Auto DRAM 1 Voltage Use this to select DRAM 1 Voltage The default value is Auto DRAM 2 Voltage Use this to select DRAM 2 Voltage The default value is Auto PLL 1 Voltage Use this to s
43. nd the other end to the device which you wish to monitor its tempera ture CLRCMOS2 allows you to clear the data in CMOS To clear CMOS take out the CMOS battery and short the Clear CMOS Pad Serial General Purpose Input Output Header SCU SGPIO1 see p 15 18 21 24 27 30 SCU SGPIO2 see p 15 24 SATA 5 1 SATA SGPIO2 see p 15 18 21 24 27 30 PSU SMBus PSUSMB1 see p 15 18 21 24 27 30 Non Maskable Interrupt Button Header BTN1 see p 16 19 22 Front Lan LED Connector FRONT LED LAN34 see p 18 24 27 30 SAS CLOCK SAS LOAD GND 1 SAS DATAIN SAS DATAOUT GND SCLOCK SDATAOUT GND GND SMBDATA 1 3VSB SMBCLK ALERT GND 1 CONTROL LAN4_LINK LED PWR LAN3 LINK LED D PWR 62 This header supports Serial Link interface for onboard SAS SATA connections This header supports Serial Link interface for onboard SATA connections PSU SMBus monitors the status of the power supply fan and system temperature Please connect a NMI de vice to this header This 4 pin connector is used for the front LAN status indicator 2 9 Driver Installation Guide To install the drivers to your system please insert the support CD to your optical drive first Then the drivers compatible to your system can be auto detected and listed on the support CD driver page Please follow the order from top to bottom to install those requ
44. nnect to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data The front panel design may differ by chassis A front panel mod ule mainly consists of power switch reset switch power LED hard drive activity LED speaker and etc When connecting your chassis front panel module to this header make sure the wire as signments and the pin assignments are matched correctly UJ This header supports mul LED PWR 12C 4 CLK LAN2 LINK 12C 4 DATA LED PWR tiple functions on the front panel including front panel GND LOCATORLED2 LOCATORLED2 y X o g lt Front panel SMBus connecting pin 6 pin FPSMB This header allows you to connect SMBus System Management Bus equipment It can be used for communication between peripheral equipment in the system which has slower transmission rates and power management equipment 57 SMB internet status indica tor and chassis intrusion pin B Internet status indicator 2 pin LAN1 LED LAN2 LED These two 2 pin headers allow you to use the Gigabit internet indicator cable to connect to the LAN status indicator When this indicator flickers it means that the internet is properly connected C Chassis intrusion pin 2 pin CHASSIS This header is provided for host computer chassis with chassis intrusion detection designs In addition it must also work wit
45. ns the jumper is Open The illustration shows a 3 pin jumper whose MT pin1 and pin2 are Short when jumper cap Short Open is placed on these 2 pins ME Recovery Jumper 1 2 3 pin ME RECOVERY1 7 3 Default see p 13 16 19 21 24 27 2 3 ME recovery mode PSU Jumper 1 2 9 pin PSU Jumper PSU SMBus loads the data aes po TOUS 1 1 1 via PCH chip 2 3 PSU SMBus loads the data via BMC chip Default 53 2 8 Onboard Headers and Connectors place jumper caps over these headers and connectors Plac Onboard headers and connectors are NOT jumpers Do ing jumper caps over the headers and connectors will cause permanent damage to the motherboard Serial ATA2 Connectors These four Serial ATA2 2 3 x SATA2 connectors sup s66 p15 16 21 24 27 30 lt port SATA data cables for SATAII 4 5 lt be see p 15 18 21 24 27 30 internal storage devices Amm The current SATA2 interface lt allows up to 3 0 Gb s data g transfer rate These four Serial ATA3 SATA3 connectors sup port SATA data cables for internal storage devices The current SATA3 interface allows up to 6 0 Gb s data transfer rate Serial ATA3 Connectors SATAIII O 1 see p 15 18 21 24 27 30 SATAIII M2 M3 see p 15 18 21 SATAIII MO M1 see p 15 18 21 24 27 30 5 0 1 SATAII M2 Io 1 1 r
46. nviroment WETTER Humidity Non operation humidity 20 90 Non condensing For detailed product information please visit our website http www asrock com EN2C606 4L EN2C602 4L EN2C602 Physical SSI EEB Status 12 x 10 5 30 5 cm x 26 7 cm Supports Intel Xeon E5 2400 1400 Series Processors Supports Hyper Threading Technology E5 1400 only supports single socket Dual Socket B2 LGA1356 System 4 1 Power Phase Design EN2C606 4L Intel C606 Chipset EN2C602 4L EN2C602 Intel C602 6x 240 pin DDR3 DIMM slots Capacity Support up to 128GB DDR3 DIMM 64GB ECC non ECC unbuffered UDIMM Triple Channel DDR3 memory technology Supports DDR3 1600 1333 1066 R LR ECC and UDIMM Voltage 1 5V 1 35V 3 slots 1 x PCIE6 x16 mode PCIe 3 0 x 18 5 x PCIEA PCIE2 x16 x0 mode or x8 x8 Expansion mode Supports D Sub with max resolution up to E 1920x1200 60Hz 10 Ethernet Storage Storage Gigabit LAN 10 100 1000 Mb s IPMI dedicated GLAN LAN Controller SATA controller SATA controller Additional SATA controller SAS controller 1 x Realtek RTL8211E for dedicated management GLAN EN2C606 4L EN2C602 4L 4 x Intel 82574L Supports Wake On LAN Supports Energy Efficient Ethernet 802 3az Supports Quad LAN with Teaming function Supports PXE EN2C602 2 x Intel 82574L Supports Wake On LAN
47. odules are properly seated in the slots 2 Use recommended DDR3 1600 1333 1066 ECC DIMMs 3 If you have installed more than one DIMM modules they should be identical with the same brand speed size and chip type 4 Try inserting different DIMM modules into different slots to identify 96 faulty ones 5 Check the settings of the 115V 230V switch on the power supply Unable to save system setup configurations 1 Verify if the battery on the motherboard provides 3VDC Install a new battery if it does not 2 Confirm whether your power supply provides adaquate and stable power Other problems 1 Try searching keywords related to your problem on ASRock s FAQ page http www asrock com support faq asp 2 Try downloading and updating the latest UEFI on ASRock s website http www asrock com support download asp 97 5 2 Technical Support Procedures If you have tried the troubleshooting procedures mentioned above and the problems are still unsolved please contact ASRock s technical support with the following information 1 Your contact information 2 Model name BIOS version and problem type 3 System configuration 4 Problem description You may contact ASRock s technical support at http www asrock com support tsd asp 5 3 Returning Merchandise for Service For warranty service the receipt or a copy of your invoice marked with the date of purchase is required By calling your vendor or going to our RMA
48. operation 93 3 9 Event Logs Aptio Setup Utility Copyright 2011 American Megatrends Inc Change Smbios Event Log Settings Change Smbios Event Log Settings This allows you to configure the Smbios Event Log Settings View Smbois Event Log This allows you to view the Smbios Event Log 94 Chapter 4 Software Support 4 1 Install Operating System This motherboard supports Microsoft Windows Server 2003 2003 R2 2008 2008 R2 Linux compliant Because motherboard settings and hardware options vary use the setup procedures in this chapter for general reference only Refer your OS documentation for more information 4 2 Support CD Information The Support CD that came with the motherboard contains necessary driv ers and useful utilities that enhance the motherboard s features 4 2 1 Running The Support CD To begin using the support CD insert the CD into your CD ROM drive The CD automatically displays the Main Menu if AUTORUN is enabled in your computer If the Main Menu does not appear auto matically locate and double click on the file ASRSETUP EXE in the Support CD to display the menu 4 2 2 Drivers Menu The Drivers Menu shows the available device s drivers if the system detects installed devices Please install the necessary drivers to acti vate the devices 4 2 3 Utilities Menu The Utilities Menu shows the application softwares that the mother board supports Click on a specific item th
49. ow er on the system USB Keyboard Remote Power On Use this item to enable or disable USB Keyboard Remote to turn on the system from the power soft off mode 69 USB Mouse Power On Use this item to enable or disable USB Mouse to turn on the sys tem from the power soft off mode 70 3 3 2 WHEA Configuration Enabled WHEA Support Use this option to enable or disable Windows Hardware Error Architecture The default value is Enabled 71 3 3 3 CPU Configuration gt CPU BSP1 Information CPU BSP1 Information Display information regarding the primary processor BootStrap Processor CPU AP1 Information Display information regarding the non primary processor Applica tion Processors Intel Hyper Threading Technology To enable this feature a computer system with an Intel processor that supports Hyper Threading technology and an operating sys tem that includes optimization for this technology is required This option will be hidden if the installed CPU does not support Hyper Threading technology Active Processor Cores Use this item to select the number of cores to enable in each pro cessor package The default value is Limit CPUID Maximum This function allows you to limit CPUID maximum value Unless the OS is Windows NT disable this function 72 No Execute Memory Protection No Execution NX Memory Protection Technology is an enhance ment to the IA 32 Intel Architecture An 32 processo
50. p Events System BIOS BIOS type Supports jumperfree SMBIOS 2 3 1 Support DRAM Voltage Multi adjustment CPU Temperature Sensing Temperature System Temperature Sensing CPU Rear Front Fan Tachometer Fan CPU Quiet Fan Allow Chassis Fan Speed Auto Adjust by CPU Temperature Monitor CPU Rear Front Fan Multi Speed Control Voltage Monitoring CPU1 2 DRAM 1 2 Water VTT1 2 VCCSA1 2 9 3V 5V 12V 1 05V_PCH BAT 3VSB 5VSB Microsoft Windows Server 2008 2008 R2 Linux compliant Operation temperature 10 35 Non Temperature operation temperature Enviroment 0 60 8 Humidity Non operation humidity 20 90 Non condensing For detailed product information please visit our website http www asrock com 13 1 4 Motherboard Layout EN2C606 4L D12 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 1 25 13 4 5 6 7 33cm 13 in FRNT FAN1 pry Ere AIXEWRI P CPU FAN1 2 CPU FAN1 1 DDR3 A1 64 bit 240 pin module DDR3 A2 64 bit 240 pi dul 5 8 O _ 2 i pin module gt
51. r with No Execute NX Memory Protection can prevent data pages from being used by malicious software to execute codes This option will be hidden if the current CPU does not support No Excute Memory Protection Hardware Prefetcher Use this turn on off the MLC streamer prefetcher Adjacent Cache Line Prefetch Use this to turn on off prefetching of adjacent cache lines DCU Streamer Prefetcher If enabled the DCU data cache unit Streamer Prefetcher prefetches the next L1 Data line based upon multiple loads in same cache line It is recommended to enable this option to en hance data processing capacity Intel Virtualization Technology When this option is set to Enabled a VMM Virtual Machine Architecture can utilize the additional hardware capabilities pro vided by Vanderpool Technology This option will be hidden if the installed CPU does not support Intel Virtualization Technology CPU Power Management Use this to configure CPU Power Management 73 3 3 4 North Bridge Configuration Configuration hub Configuration Intel VT d Use this to enable disable Intel Virtualization Technology for the Directed Intel Use this to enable disable Intel I O AccelearationTechnology Primary Graphics Adapter This allows you to select a graphics device as the primary display The default value is PCI Express Onboard VGA Enable or disable the onboard VGA For EN2C606 4L D12 EN2C602 4L
52. rd Intel Processor Intel Processor DDR3 1066 1333 1600 i 1066 1333 1600 SNB EN IVB EN SNB EN IVB EN DDR3 1066 1333 1600 i 1066 1333 1600 1066 1333 1600 LGA 1356 Pin Socket LGA 1356 Pin Socket CPU 1 CPU DDR3 1066 1333 1600 PCIE Gen3 x16 SLOT x16 PCIE Gen3 x16 SLOT x8 100MHz PCIE Gen3 BUS PCIE Gen3 X16 SLOT X16 PCIE Gen2 x1 Slot x1 1 PCIE Gen3 X4 SLOT x4 100MHz ING uo5 sers ine 1825741 100MHz E SCU C602 chipset only SATA 2 0 p E PCI PCI SLOTI CI C602 SATAIII M2 arven9230 lt 2 PCI SLOT2 NCSI LANI Inte182574L PCIE 100MHz SPI FLASH BMC ASPEED 64Mb D SUB Connector 1512300 PCIEx1 100MHz LPC BUS KB MS Nuvoton COM Port Connector NCT6776 Realtek PHY 8211E 40 EN2C606 4L 12 on Board DDR3 1066 1333 1600 DDR3 1066 1333 1600 1066 1333 1600 PCIE Gen2 x1 Slot 1 5741 Intel 3 5741 Intel 4 1nte182574L SATA3 M 19220 SATAIII MO SATAIII Ml TA D SUB Connector COM Port Connector Realtek PHY 8211E SPI FLASH BMC ASPEED A
53. rd s holes Step 4 Use a screw driver to install the screws If you press down the fasteners without rotating them clock wise the heatsink cannot be secured on the motherboard Step 5 Connect CPU fan connector with the fan header on the motherboard Step 6 Secure redundant cable with tie wrap to ensure that the cable does not interfere with the fan s operation or contact other components 48 2 5 Installation of Memory Modules DIMM This motherboard provides four 240 pin DDR3 Double Data Rate 3 DIMM slots and supports Dual Channel Memory Technology For dual channel configuration you always need to install two identical the same brand speed size and chip type memory modules in the DDR3 DIMM slots to activate Dual Channel Memory Technology Otherwise it will operate at single channel mode It is not allowed to install a DDR or DDR2 memory module into DDR3 slot otherwise this motherboard and DIMM may be damaged 28 If you install only one memory module or two non identical memory modules it is unable to activate Dual Channel Memory Technology 9 Some DDR3 1GB double sided DIMMs with 16 chips may not work on this motherboard It is not recommended to install them on this motherboard 4 Asingle memory module should be installed in the blue socket 5 If you install only one CPU CPU BSP1 on moth erboard make sure to install DIMMs into DDR3 A DDR3 B or DDR3 C Installing a DIMM Please m
54. s when on demand inactive memory is auto matically activated by the system to temporarily replace failed memory until a service action can be performed DRAM RAPL BWLIMIT This item sets the limits on the average power consumption and the bandwidth of DRAM module The options are Disabled 0 1 Intel recommended value 8 and 16 Perform and DFX devices This item can set the Perfmon and DFX devices hidden or unhid den DRAM RAPL Running Average Power Limit Mode RAPL Running Average Power Limit provides mechanisms to enforce power consumption limits on supported processors The default is DRAM Mode 1 76 Numa Enable or disable the support of Non Uniform Memory Access MPST Support Enable or disable the support of Memory Power StateTable DRAM Frequency If Auto is selected the motherboard will detect the memory module s inserted and assign the appropriate frequency auto matically Channel Interleaving It allows you to enable Channel Memory Interleaving The default value is Auto Rank Interleaving It allows you to select a rank memory interleaving method The default value is Auto Patrol Scrub Patrol Scrub is a background activity initiated by the processor to seek out and fix memory errors The default value is Enabled Demand Scrub Fix the error when the CPU or I O issues a demand read com mand and the read data from memory turns out to be a correct able error The default value is Disabled Dat
55. s you to set the speed of FRNT Fan3 The default value is Full On FRNT 4 Setting This allows you to set the speed of FRNT Fan42 The default value is Full On Watch Dog Timer This allows you to enable or disable the Watch Dog Timer The default value is Disabled Case Open Feature This allows you to enable or disable the Case Open Feature The default value is Enabled Clear Status Enable to clear case open status if case open has been detected 88 3 5 Server Management System Event Log Enter to configure System Event Logging features during boot BMC Network Configuration Enter to configure BMC Network parameters 89 3 6 Boot Screen In this section it will display the available devices on your system for you to configure the boot settings and the boot priority Boot Option 1 USB TDKMedialSB D Boot Option 71 Select boot option 1 Boot Option 2 Select boot option 2 Boot Option 3 Select boot option 3 USB Device BBS Priorities Set the boot priorities for USB devices Setup Prompt Timeout This shows the number of seconds to wait for setup activation key 65535 means indefinite waiting Bootup NumLock State If this item is set to On it will automatically activate the Numeric Lock function after boot up PCI ROM Priority Use this to adjust the PCI ROM Priority The default value is Leg 90 Full Screen Logo Use this item to enable or disa
56. siness and the like even if ASRock has been advised of the possibility of such damages arising from any defect or error in the manual or product Fe This device complies with Part 15 of the FCC Rules Operation is subject to the fol lowing two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation CALIFORNIA USA ONLY The Lithium battery adopted on this motherboard contains Perchlorate a toxic substance controlled in Perchlorate Best Management Practices BMP regulations passed by the California Legislature When you discard the Lithium battery in Cali fornia USA please follow the related regulations in advance Perchlorate Material special handling may apply see www dtsc ca gov hazardouswaste perchlorate ASRock Website http www asrock com Contents 1 Introduction em 5 1 1 Package Gonlenls icr Ra enn Eau nenne 5 1 2 Specifications 6 1 3 Motherboard 14 1 4 32 1 5 Block MEI m 38 2 44 2 1 Pre installation Precautions 44 22 Screw UR En rx is 44 23 CPU InstallatODL c tessera pu Yeu E a EE vae Led 45 2 4 Installation of Heatsink and CPU fan 48 2 5 Installation of Memory Modules D
57. t For proper inserting please ensure to match the two orientation key notches of the CPU with the two alignment keys of the socket Step 3 3 Carefully place the CPU into the socket Step 3 4 Verify that the CPU is within the socket and properly mated to the orient keys 46 Step 4 Close the socket Step 4 1 Flip the load plate onto the IHS Step 4 2 Press down the load lever and secure it with the load plate tab under the retention tab 47 2 4 Installation of CPU Fan and Heatsink This motherboard is equipped with 1356 Pin socket that supports Intel 1356 Pin CPUs Please adopt the type of heatsink and cooling fan com pliant with Intel 1356 Pin CPU to dissipate heat Before you install the heatsink you need to spray thermal interface material between the CPU and the heatsink to improve heat dissipation Ensure that the CPU and the heatsink are securely fastened and in good contact with each other Then connect the CPU fan to the CPU FAN connector For proper installation please kindly refer to the instruction manuals of your CPU fan and heatsink Below is an example to illustrate the installation of the heatsink for 1356 Pin CPUs Step 1 Apply thermal interface material onto the center of the IHS on the socket s surface Step 2 Place the heatsink onto the socket En sure that the fan cables are faced on the side closest to the CPU fan connector on the motherboard Step 3 Align screws with the motherboa
58. the motherboard specifications and the BIOS software 4 might be updated the content of this manual will be subject to change without notice In case any modifications of this manual occur the updated version will be available on ASRock s web site without further notice You may find the latest VGA cards and CPU support list on ASRock s website as well ASRock website http www asrock com If you require technical support related to this motherboard please visit our website for specific information about the model you are using www asrock com support index asp 1 1 Package Contents ASRock EN2C606 4L D12 EN2C602 4L D12 EN2C602 D12 Mother board SSI CEB Form Factor 12 0 in x 13 in 30 5 cm x 33 cm or ASRock EN2C606 4L EN2C602 4L EN2C602 Motherboard SSI CEB Form Factor 12 0 in x 10 5 in 30 5 cm x 26 7 cm Quick Installation Guide Support CD 5 x Serial ATA SATA Data Cables Optional 1 x I O Panel Shield 1 2 Specifications EN2C606 4L D12 EN2C602 4L D12 EN2C602 D12 Physical SSI EEB Status 12 x 13 30 5 cm x 33 cm Supports Intel Xeon E5 2400 1400 Series Processors Supports Hyper Threading Technology E5 1400 only supports single socket Susp Dual Socket B2 LGA1356 System 4 1 Power Phase Design EN2C606 4L D12 Intel C606 Chipset EN2C602 4L D12 EN2C602 D12 Intel C602 12 x 240 pin DDR3 DIMM slots Capacity Support up to 192GB DDR3 DIMM 96GB ECC non ECC unb
59. uffered UDIMM Me Triple Channel DDR3 memory technology Type Supports DDR3 1600 1333 1066 R LR ECC and UDIMM Voltage 1 5V 1 35V 3 slots PCle 3 0 x 16 2 x PCIE3 amp PCIE6 x16 mode Expansion 1 x PCIES x 8 mode Output Supports D Sub with max resolution up to 4 1920x1200 60Hz Ethernet Storage Storage Gigabit LAN 10 100 1000 Mb s IPMI dedicated GLAN LAN Controller SATA controller SATA controller Additional SATA controller SAS controller 1 x Realtek RTL8211E for dedicated management GLAN EN2C606 4L D12 EN2C602 4L D12 4 x Intel 82574L Supports Wake On LAN Supports Energy Efficient Ethernet 802 3az Supports Quad LAN with Teaming function Supports PXE EN2C602 D12 2 x Intel 82574L Supports Wake On LAN Supports Energy Efficient Ethernet 802 3az Supports Quad LAN with Teaming function Supports PXE EN2C606 4L D12 Intel C606 2 x SATA3 6 0 Gb s 4 x SATA2 3 0 Gb s support RAID 0 1 5 10 and Intel Rapid Storage 3 0 EN2C602 4L D12 EN2C602 D12 Intel C602 2 x SATA3 6 0 Gb s 8 x SATA2 3 0 Gb s support RAID 0 1 5 10 and Intel Rapid Storage 3 0 Marvell SE9230 4 x SATA3 6 0 Gb s support RAID 0 1 5 10 NCQ AHCI Hot Plug functions EN2C606 4L D12 Intel C606 8 x SATA2 SAS 3Gb s support RAID 0 1 5 10 EN2C602 4L D12 EN2C602 D12 EN2C606 4L D12 EN2C602 4L D12 4x RJ45 Gigabit Ethernet LAN ports Re
60. website http www asrock com support index asp cat RMA you may obtain a Returned Merchandise Authorization RMA number The RMA number should be displayed on the outside of the shipping carton which is mailed prepaid or hand carried when you return the motherboard to the manufacturer Shipping and handling charges will be applied for all orders that must be mailed when service is complete This warranty does not cover damages incurred in shipping or from failure due to alteration misuse abuse or improper maintenance of products Contact your distributor first for any product related problems during the warranty period 98

Download Pdf Manuals

Related Search

Related Contents

www.dudek.eu  Dual Multi-UHF Wireless System  Samsung SCC-C4255 User's Manual  Northwest 80-EF421S Instructions / Assembly  - Rausser Handelsfirma  Insignia NS-A1000 User's Manual  2012年.夏号（ 、1320.6 KB）    Philips SWV2025W Feed-thru Dual pack F connectors    

Copyright © All rights reserved. Failed to retrieve file