Operators Manual
Contents
1. IN300 PRINTER OPERATOR S MANUAL Inscale Measurement Technology Ltd pry 7 Heron Close St Leonards on Sea East Sussex TN38 8DX United Kingdom Tel 44 0 1424 200722 Fax 44 0 1424 443976 Email sales inscale scales couk s ese _Inscale Http www inscale scales co uk Solutions in Weighing Technology Inscale Measurement Technology Ltd follows a policy of continuous improvement and reserves the right to change specifications without notice October 2002 Manufacturer s Declaration of Conformity This product has been manufactured in accordance with the harmonised European standards following the provisions of the below stated directives Electro Magnetic Compatibility Directive 89 336 EEC Low Voltage Directive 73 23 EEC Inscale Measurement Technology Ltd 7 Heron Close St Leonards on Sea East Sussex TN38 8DX United Kingdom FCC COMPLIANCE This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment The equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio communications Operation of this equipment in a residential area is likely to cause harmful interference2. printer must be connected to a PC or terminal A Windows program to set the data and time is available from Inscale Contact us for more information Inscale 2000 2 SELF TEST Press and hold the Paper Feed button down when power is turned on then release the button The printer will print the current settings and a description of all set up key functions INTERFACE Printer 5 pin DIN connector Pin 1 Pin 2 Pin 3 Pin 4 Pin 5 RXD DTR GND nu TXD Inscale Balances 9 Pin D Subminiature Socket Pin 3 Pin 1 Pin 5 Pin 2 Data from Scale Not used by scales Signal ground Date to scale In addition on early models of ADA and all ADP and ADG units Connected to Pin 8 Connected to Pin 6 Inscale 2000 Pin 7 Pin 4 CONTROL CODES LF OAh Line feed CR ODh Carriage Return SO OEh Double Strike Mode DC4 14h Double Strike Mode Cancel CAN 18h Clear Buffer ESC An 1Bh 41hn Line spacing in n 72 inch ESC 2 1Bh 32h 1 6 inch line spacing ESC 0 1Bh 30h 1 8 inch line spacing ESC 4 1Bh 34h 40 characters line normal ESC 8 1Bh 38h 80 characters line extended Printer Dot matrix Thermo printer Bi directional printing 0 75 lines per second 40 or 80 characters per line Paper 112mm thermo paper PH65 or HONSHU Standard 20 meter roll Size 60 x 180 x 150mm 0 6kg Interface RS 232 or RS 242 TTL 5 pin DIN Connector 1200 2400 4800 or 9600 baud 8 bit or 7 bit With or without parity Inscale 200
3. 0 4 PAPER LOADING See diagram Cut paper at angle and feed into slot from rear Press and hold the Paper Feed button until the paper passes through the printer Do not pull paper or force through the slot If the paper does not feed easily check you are using the paper entry slot and there are no obstructions in the paper path gt tes 12345678 Configuration Dip Switch Paper Loading Note direction of paper roll Inscale 2000 5 CONFIGURATION The printer is set with the dip switches under the paper roll The default settings are 4800 baud 8 bit no parity 40 column CR only To reset the switches turn the printer off Set the switches as desired and then turn the printer the printer on 1200 2400 4800 9600 baud SW1 on off on off SW2 on on off off SW3 on 8 bit data Off 7 bit data SW4 on Parity enabled Off parity ignored SW5 on parity even Off parity odd SW6 on 80 column Off 40 column SW7 on CR prints CR only Off CR prints CR LF SW8 on 2 column double ticket Off 1 column normal printing Inscale 2000 6 Inscale 2000 Copyright by Inscale Measurement Technology Ltd All rights reserved No part of this publication may be reprinted or translated in any form or by any means without the prior permission of Inscale Inscale reserves the right to make changes to the technology features specifications and design of the equipment without notice All information contained within this publication wa
4. in which case the user will be required to correct the interference at his own expense Shielded interconnect cables must be employed with this equipment to insure compliance with the pertinent RF emission limits governing this device Changes or modifications not expressly approved by Inscale could void the user s authority to operate the equipment Inscale 2000 IN300 PRINTER The IN300 Printer is a general purpose thermo tally roll printer specifically designed to work with the Inscale series of balances Some models have a optional time and date function This function will allow the printout to include time and date information when the balance time date function is enabled The printer comes preset to work with the default RS 232 interface found on the Inscale balances but can easily be changed to work on other equipment The printer is easy to use with only an On Off switch and a paper feed button Inscale 2000 1 SPECIFICATIONS Power Supply 8 5 to 14VDC or 7 to 10VAC from module 15 Watts when printing 3 Watts when idle Mains Supply As required 230VAC 50 60Hz UK or European 115VAC 50 60Hz USA Environment 5 to 35 C 10 to 80 humidity non condensing On printers with optional date time function ESC T yymmddhhnn yy year mm month dd date hh hour nn minute For example to enter 12 April 1999 time 14 15 send ESC T 99h 04h 12h 14h 15h 1B 54 99 04 12 14 15 hex To set the time and date the
5. s to the best of our knowledge timely complete and accurate when issued However we are not responsible for misimpressions which may result from the reading of dated material The latest version of this publication can be found at our Website see below Inscale Measurement Technology LTD 7 Heron Close St Leonards on Sea East Sussex TN38 8DX U K Email sales inscale scales co uk Website http www inscale scales co uk Inscale 2000
Download Pdf Manuals
Related Search