iLaser User Guide
Contents
1. EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 amp Harmonized Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and similar electrical appliances Part 1 General requirements Innovation Quality Performance P Z Solution Your integrated Solution LINKABLE oes STAND ALONE User Guide lease read these instructions carefully before us e 5 Troubleshooting Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A If the unit does not work no light output or fan is not working 1 Check the main power connection and the fuse 2 Measure the mains voltage on the main power connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one 4 Try to use another DMX controller 5 Check if the D2. MX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C Some units don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2C D No response to the sound 1 Check the unit that is not receiving DMX signal 2 Check the unit that is not set to display mode 3 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition 6 Fixture Cleaning The cleaning of internal and external optical lenses and or mirrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days TABLE OF CONTENTS Safety Instruction Technical Specification 2 1 Beam Angel How To Set The Unit 3 1 Control Panel 3 2 Main Function How To Control The Unit 4 1 Master Slave Built In Preprogrammed Function 4 2 Easy Controller 4 3 DMX Control
3. again 7C Display Inversion It is good for you to install the unit on the floor or under ceiling Press the MENU button up to when the is blinking on the display Use the ENTER button to change to the mode oar display inversion It will automatically store after 8 seconds Or press the ENTER display normal To go back to the functions press button again return to the mode the MENU button Display normal mode for the fixture putting on the floor Display inversion mode for the fixture fixing under ceiling LIC Self Test Press the MENU button up to when the 52 2 js blinking on the display Pressing ENTER button and the unit will run self test by built in program To go back to the functions press the MENU buiton again Vit ol Fixture Hours Press the MENU button up to when the 5 is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button again Reset Press the MENU button up to when the Se is blinking on the display Pressing ENTER button and all channels of the unit will return to their standard position To go back to the functions press the MENU button again
4. efore any service is done e When the laser starts up it is normal for output to vary After several minutes the laser output will stabilize IMPORTANT Install the laser projector in a manner that prevents the audience from looking directly into the beams The installation should assure that the beam will not strike the audience ee DANGER VISIBLE LASER RADIATION AVOID DIRECT EYE EXPOSURE 3C 4 5 DMX512 Connection The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels kt DMX512 Oohm 1 4W INPUT Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pins DMX of the last fixture 1 If you using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX into a 3 pin XLR plug and plug it in the DMxX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable can not be branched or split to a Y cable DMX512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX output and i
5. ler 4 3 1 Universal DMX Controller 4 3 2 IL 0824 Controller 4 4 DMX512 Configuration 4 5 DMX512 Connection Troubleshooting Fixture Cleaning 1 Safety Instruction A WARNING Please read carefully the instruction which includes important information about the installation usage and maintenance fox LASER RADIATION AVOID DIRECT EYE EXPOSURE WAVELENGTH 532nm GREEN The following points are important for safety as well as for the smooth installation and performance of the unit e Unpack carefully and be sure that no damage has occurred during transportation e It is very important to ground the yellow green conductor in order to meet regulations for Safety e Do not connect the device to any dimmer pack e The electrical work that is necessary for installation must be made by qualified personnel e Be sure to locate the unit in a place with adequate ventilation at least 15 cm from the walls Be sure that no ventilation slots are blocked e Be careful that no liquids or other objects can enter the unit If this ever happens disconnect the main power immediately e In the event of serious operating problems turn off the power immediately Never try to repair the unit yourself Repairs carried out by non qualified personnel can lead to serious damage or malfunction Please contact your dealer for technical assistance Always use genuine spare parts e Always remember to unplug the unit from the power mains b
6. ments or performance of procedures other than as specified herein may result in hazardous radiation exposure 5C 4 2 Easy Controller The easy remote control is used only in master slave mode By connecting to the 1 4 microphone jack of the first unit you will find that the remote control on the first unit will control all the other units for Stand by Function and Mode Stand By Dot on line or Changeable Fixed pattern discontinuous pattern selection selection line effect 16 patterns 8 patterns LED off LED on LED blinking saine 4 3 DMX Controller 4 3 1 Univeral DMX Controller If you use a universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again Please refer to the following diagram to address your DMX512 channel for the first 4 units aL BL Lt 4 3 2 IL 0824 Controller If you use iLead 0824 controller Please refer to the following diagram to address your DMX512 channel for the first 4 units DMX add
7. n be set remotely by iLead controller please refer to the user 064 076 3 oe manual of iLead controller No need to calculate the DMX channels of each fixture in 052 063 the chain 039 051 e When the MDX signal is off the lights will switch to Master Slave mode 026 038 010 Fastest speed Left Right l aclest en m elackwise 008 015 tirei i r p g 010 Fastest speed counterclockwise automatically 013 025 000 009 Stopped 000 009 Stopped 900 Zoom in min e Easy installation easy addressing and easy operation Dimension 320 x 205 x 100 mm Weight 2 24 kg 000 7 Blackout oo0 012 2 1 Beam Angel La IIA Trt BE aN a o oor Bic N Crys Distance m 3 How To Set The Unit 3 1 Control Panel MASTER QO SLAVE 1 Display To show the various menu and the selected functions 2 LED DMX input present MASTER Master mode SLAVE On Slave mode SOUND Flashing Sound activation 3 Button MENU To select the programming functions DOWN To go backward in the selected functions UP To go forward in the selected functions ENTER To confirm the selected functions 4 Remote controller input By connect to the 1 4 microphone jack to control the unit for Stand by Function and Mode function 5 Microphone To receives audio signal for sound activation 6 DMX input output For DMX512 link use 3 pin XLR plug cable to link the unit together CAUTION Use of controls or adjust
8. nput connectors are pass through to maintain the DMX circuit when power is disconnected to the unit 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually 0 amp 1 are equal to 1 6 The end of the DMX512 system should be terminated to reduce signal errors 7 3 pin XLR connectors are more popular than 5 pin XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 4 4 DMX512 Configuration 2 Technical Specification e Power supply DMX512 CONFIGURATION AC 120V 60Hz CHANNEL1 CHANNEL CHANNELS CHANNEL4 o CHANNELS _ a AC 230 240 250V 50 60Hz 248 255 Laseron Ne 46 246 299 Stopped cane a e Laser diode MS Fasticet speed UNDG Zoom in out Green laser diode x 1 4 9 mW or 30 mW iia Class Illa for laser output lt 4 9 mW O 2B lowest Speed e DMX Channels Standard DMX512 signal addressing and can be controlled by any universal DMX Q controller 127 Zoom out max Channel 1 Laser on off dot on line discontinuous lines 135 Slowest speed Up Down 1135 Slowest speed clockwise Channel 2 Pattern 016 131 ee 121 134 Stopped 121 134 Stopped Channel 3 Movement er Channel 4 Rotation S 120 Slowest speed Left Right 120 Slowest speed counterclockwis os0 102 Q Channel 5 Zoom 077 089 D e DMX address ca
9. o back to the functions without any change press the MENU button again 1 IL VLILI Slave Mode Press the MENU button up to when the Lid jg showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the normal or 2 light show mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU buiton again LIL I L Blackout Mode 2 is showing on the display Pressing ENTER Press the MENU button up to when the button and the display will blink Use DOWN and UP button to select the 4 oo yes blackout or no blackout mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Led Display Press the MENU button up to when the _ amp ois showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the nik Led on or L Led off mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button
10. ress can be set remotely by IL 0824 controller No need to calculate the DMX channels of each fixture in the chain Following DMX address setting is based on that all the lighting fixtures are linked together controlled by the 8 channel iLead IL 0824 controller AL tL asi en 4 How To Control The Unit You can operate the unit in three ways 1 By master slave built in preprogram function 2 By easy controller 3 By IL 0824 please refer to the user guide of iLead controller or universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show ILS 5 on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 4 1 Master Slave Built In Preorogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash to the music The other units will have to set in slave mode Suna and select normal or 2 light show mode Their DMX cables plugged into the DMX input jacks daisy chain and the slave led light
11. s will constantly on 2 light show In Suto slave mode means the unit works normally and means 2 light show In order to create a great light show you can set on the second unit to get contrast movement to each other even if you have two units only 6C To select any of the given functions press the MENU button up to when the required one is showing on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press the ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds To go back to the functions without any change press the MENU button The main functions are showing below Addr Fe 3 DMX512 Address Setting TE L i Slave mode Normal 00 Lel d Slave mode 2 Light Show End uU bo Blackout Mode Yes Blackout GENT 17 On bol Blackout Mode No Blackout remm rlon LEDon LEd off LED off 4 goo i dSP Display Normal dSP Display Inversion EPSL Self Test FheS Fixture Hours cSPt Reset DMX512 Address Setting Press the MENU button up to when the Cr js showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To g
Download Pdf Manuals
Related Search