Shure 515BSLX Microphone User Guide
Contents
1. Model 515BSLX User Guide SPECIFICATIONS Type Dynamic moving coil Frequency Response Figure 1 80 to 15 000 Hz 20 1 cm 3 8 in i an Sy 10 7 Sy A g o omen 20 2 3 456789 2 3 456789 20 50 100 1000 10000 20000 Hz TYPICAL FREQUENCY RESPONSE FIGURE 1 Polar Pattern Figure 2 Cardioid unidirectional Effective rejection of sound at rear of microphone is uniform with frequency front pickup characteris MODEL 515BSLX tics are symmetrical about axis UNIDIRECTIONAL MICROPHONE The Shure Model 515BSLX is a dynamic moving coil low im pedance cardioid unidirectional microphone designed for mount ing on a gooseneck or fixed pipe with a 5 8 in 27 thread The cardioid pickup pattern provides excellent voice reproduction with effective rejection of feedback and background noise The 515BSLX is especially suitable for use in communications paging and talkback systems The microphone is supplied with a slide switch controlling the microphone audio and a relay circuit permit ting hands free operation The microphone comes with a 1 8 m 6 2500 Hz 250 Hz ft four conductor two conductors shielded cable cae Se Cece ots The 515BSLX is wired with the microphone circuit normally er ah ears 1 Q00U open for use in parallel wired microphone installations TYPICAL POLAR PATTERN FIGURE 2 FEATURES Impedance e Rolled o2. ements EN 50 082 1 1992 WIRING CONNECTIONS The RED and BLACK cable leads are the microphone audio conductors for balanced line connections the shield is connected to the amplifier ground The GREEN and WHITE leads control an external relay or switching circuit Refer to the following table and the wiring diagram in Figure 4 INPUT TYPE WIRE FUNCTION XLR 1 4 IN COLOR CONNECTOR PHONE PLUG UNBALANCED BLACK AUDIO GROUND PIN 3 SLEEVE La SHIELD CHASSIS GROUND PIN 1 SLEEVE BALANCED BLACK AUDIO PIN 3 a SHIELD CHASSIS GROUND SLEEVE 1 ral Lono T SWITCH SHOWN IN OFF POSITION INTERNAL CONNECTIONS FIGURE 4 r X MOUNTING To mount the microphone on a gooseneck or fixed pipe with a 5 8 in 27 mounting thread proceed as follows 1 Use the supplied hex wrench to loosen the setscrew enough so that the end cap can be unscrewed from the microphone 2 Remove the end cap from the microphone Remove the thin metal washer and the metal spacer 4 Replace the washer by sliding it on to the cable and up into the end of the microphone 5 Slip the cable through the gooseneck or pipe 6 Thread the microphone firmly onto the end of the gooseneck Or pipe 7 Tighten the setscrew to prevent the microphone from loosen ing Sa FURNISHED ACCESSORIES 1 27 mm 050 mm Hex Wrench 80A67 REPLACEMENT PARTS Sine e e 4 ba ezbentegietseuetegdes eeeee
3. es R180 Grille Assembly 0 000000 ee eee RK334G Cable 1 8m 6 ft 0005 70A4172 OPTIONAL ACCESSORIES Black Gooseneck 0 3 m 12in G12B Black Heavy duty Mounting Flange A13HDB WVINOSCICCH cesses ore eas ee ee oe eee oes 28 A1WS Black Mounting Flange 05 A12B For additional service or parts information please contact Shure s Service department at 1 847 600 8699 Outside the United States please contact your authorized Shure Service Center SHURE SHURE Incorporated http www shure com United States Canada Latin America Caribbean 5800 W Touhy Avenue Niles IL 60714 4608 U S A Phone 847 600 2000 U S Fax 847 600 1212 Intl Fax 847 600 6446 Europe Middle East Africa Shure Europe GmbH Phone 49 7131 72140 Fax 49 7131 721414 Asia Pacific Shure Asia Limited Phone 852 2893 4290 Fax 852 2893 4055
4. ff low frequency response combined with a 150 Q rated 180 Q actual smooth high frequency rise for clear and intelligible voice a pickup Sensitivity at 1 000 Hz e Symmetrical cardioid pickup pattern minimizes feedback LOZ e Shock mounted cartridge for quiet operation and low Open Circuit Voltage 57 0 dBV Pa 1 4 mV stand handling noise 1 Pa 94 dB SPL e Neodymium magnet for high signal to noise ratio Polarity e Heavy duty zinc die cast locking metal grille protects Positive pressure on diaphragm produces positive voltage on cartriage and resists wear the RED lead with respect to the BLACK lead e Built in slide switch controls both microphone circuit and i relay or control circuit Switch e Backed by the Shure 2 years warranty Built in double pole double throw slide switch Lockplate to lock switch ON 2005 Shure Incorporated a4 C Printed in U S A 27E2975 Rev 9 Shock Mount Internal rubber vibration isolator Cable 1 8 m 6 ft cable with effective hum shielding four conductors two shielded plastic jacketed Case Black finish die casting with black enamel diecast grille and stainless steel screen DIMENSIONS FIGURE 3 1 8m 6 tt 16 5 cm 6 5 in Ms 5 2 cm 0 85 in 2 OVERALL DIMENSIONS FIGURE 3 Net Weight 315 grams 11 1 oz CERTIFICATION Conforms to European Union directives eligible to bear CE marking meets European Union EMC Immunity Requir
Download Pdf Manuals
Related Search