User Guide for Cisco Virtualization Experience Client 6215
Contents
1. Press the Speaker button to answer a call or to end a call To end an active call and answer an incoming call press the Speaker button twice To reject an incoming call press the Speaker button twice To put a call on hold and answer an incoming call press and hold the Speaker button for two seconds To switch between an active call and a call on hold press and hold the Speaker button for two seconds If Cisco Jabber is running and you have no incoming active or held calls you can press the button to make the speakerphone your active device The speakerphone plays a beep tone to let you know that it is ready and Cisco Jabber becomes the active window Plug the USB cable into this USB port USB connections only Set the OFF ON Bluetooth switch to ON for a USB connection Set the OFF ON Bluetooth switch to Bluetooth for Bluetooth connections Press the Connect button to reconnect with or to disconnect from a Bluetooth device User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 jE Accessories Device Selector Set up your hands free speakerphone USB connection Procedure Step1 Connect the USB cable to the Jabra Speak 450 Step2 Plug the other end of the USB cable into an available USB port Step3 On the base of the speakerphone set the OFF ON Bluetooth switch to the ON position Set up your hands free speakerphone Bluetooth connection With the Jabra Link2. Logitech Wirelesss Mouse features Figure 6 Logitech Wireless Mouse features Table 3 Legend Left and right mouse buttons Scroll wheel Battery LED Flashes green when mouse is powered on and flashes red when the battery power is low Middle button The function of this button depends on your operating system and the application being used For example if you browse the Internet in Microsoft Windows and use the Middle button to click a link typically the link opens in a new tab Internet back and forward Tilt the scroll wheel right to move forward one page Tilt the scroll wheel left to move back one page OFF ON slider switch Lid release for the storage and battery compartment lid Unifying receiver storage When the mouse is not in use you can store the Unifying receiver inside the mouse User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 jE Accessories Logitech Mouse M525 C Set up your mouse Figure 7 Mouse setup User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 16 l Accessories Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Logitech WebCam C920 C i Procedure On the bottom of the mouse push the release for the storage compartment Turn the mouse over and remove the lid from the storage compartment Remove the Unifying Receiver from the storage compartment Instal
3. User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 E Accessories Jabra Speak 450 for Cisco amp Note You can pair only one handset with the cradle at a time Procedure Step1 Connect the USB cable to the handset cradle Step2 Plug the USB cable into an available USB port on your Cisco Virtualization Experience Client Step3 Place the handset in the cradle The handset pairs with the cradle and begins charging Power your handset off and on The Jabra Handset 450 for Cisco is always powered on when it is in the handset cradle iS Note The handset powers off automatically if it is out of range of the cradle for four minutes or longer Procedure tep 1 sep To power off the handset press and hold for 5 seconds Step 2 A To power the handset back on press Jabra Speak 450 for Cisco The Jabra Speak 450 for Cisco is a hands free speakerphone The Jabra Speak 450 was designed for Cisco to work in Cisco Unified Communications environments User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 2 l Accessories Jabra Speak 450 for Cisco i Jabra Speak 450 features Figure 11 Jabra Speak 450 features Oo p 2 3 Table 6 Legend Press the Mute button to toggle mute Press the Volume or Volume button to adjust the speaker volume up or down
4. Cisco virtual environment In this document Cisco Virtualization Experience Client means Cisco Virtualization Experience Client 6215 e Your hosted virtual desktop page 1 e Virtualization Experience Client firmware page 1 e Virtualization Experience Media Engine page 1 e Your Cisco Virtualization Experience Client page 2 Your hosted virtual desktop The hosted virtual desktop HVD is a new form of desktop computing Your HVD looks and behaves like a regular desktop However your Windows desktop other software and your data reside in a central location called a data center You access your HVD over a secure connection with your Cisco Virtualization Experience Client The HVD removes the need for typically more costly physical desktop PCs Central hosting in the data center reduces the cost of providing the applications and computing services that you need This type of setup is commonly referred to as a virtual environment Virtualization Experience Client firmware Your system administrator preinstalls the Virtualization Experience Client firmware on your Cisco Virtualization Experience Client The firmware includes Cisco AnyConnect Note Cisco Virtualization Experience Media Engine is an optional add on Virtualization Experience Media Engine Your system administrator also preinstalls the optional Cisco Virtualization Experience Media Engine VXME add on which provides support for the following accessories U
5. 360 you can connect the Jabra Speak 450 to your Cisco Virtualization Experience Client over Bluetooth amp Note You can pair up to eight devices with the Jabra Link 360 however only one active audio path is supported at a time For more information about the Jabra Link 360 visit http www jabra com Before You Begin Power off all devices that previously connected to paired with the Jabra Link 360 Procedure Step1 On the base of the speakerphone set the OFF ON Bluetooth switch to the Bluetooth position Step2 On the base of the speakerphone press Connect Step3 Plug the Jabra Link 360 into an available USB port The LED indicator flashes blue to indicate that the Jabra Link 360 is in pairing mode It can take up to a minute to establish the connection The LED turns solid blue when pairing is complete Device Selector The Device Selector is part of Cisco Virtualization Experience Media Engine VXME Device Selector is a menu that you use to manage your cameras and audio devices You can view your currently active cameras and audio devices or change them A list of audio devices appears first in the menu followed by a list of cameras The list of audio devices includes the thin client built in audio device Your active camera and audio device selections apply to all applications The icon for the Device Selector By appears in the notification area in the bottom right corner of the screen Some icons including the Device
6. 6 l Connect to your hosted virtual desktop Citrix connection i connection on the Cisco Virtualization Experience Client desktop Alternately your administrator can set XenDesktop or XenApp to start automatically when you boot your Cisco Virtualization Experience Client You require a username and password to connect to your HVD If you do not know your username and password contact your system administrator The following image shows the Citrix XenDesktop log on page Figure 2 Citrix XenDesktop log on Citrix XenDesktop Your Windows desktops and apps on demand from any PC Mac smartphone or tablet User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 jE Connect to your hosted virtual desktop VMware connection The following image shows the Citrix XenApp log on page Figure 3 Citrix XenApp log on Citrix XenApp Log on Your Windows desktops and apps on demand from any PC Mac smartphone or tablet 347374 VMware connection After you connect to the corporate network either directly or by using Cisco AnyConnect you can connect to your hosted virtual desktop HVD and use other network resources If your Cisco Virtualization Experience Client connects to your HVD over a VMware connection you use VMware Horizon View Client to log on Your administrator can place the shortcut icon for VMware Horizon View on your Cisco Virtualization Experience Client desktop or set VM
7. AMED SUPPLIERS DISCLAIM ALL WARRANTIES EXPRESSED OR IMPLIED INCLUDING WITHOUT LIMITATION THOSE OF MERCHANTABILITY FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING USAGE OR TRADE PRACTICE IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT SPECIAL CONSEQUENTIAL OR INCIDENTAL DAMAGES INCLUDING WITHOUT LIMITATION LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES Cisco and the Cisco logo are trademarks or registered trademarks of Cisco and or its affiliates in the U S and other countries To view a list of Cisco trademarks go to this URL http d www cisco com go trademarks Third party trademarks mentioned are the property of their respective owners The use of the word partner does not imply a partnership relationship between Cisco and any other company 1110R Any Internet Protocol IP addresses used in this document are not intended to be actual addresses Any examples command display output and figures included in the document are shown for illustrative purposes only Any use of actual IP addresses in illustrative content is unintentional and coincidental 2013 Cisco Systems Inc All rights reserved CONTENTS CHAPTER 1 Your Cisco virtual environment 1 Your hosted virtual desktop 1 Virtualization Experience Client firmware 1 Virtualization E
8. Ajaj CISCO p 5 A z HA no EA fd l User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 First Published April 02 2013 Last Modified April 02 2013 Americas Headquarters Cisco Systems Inc 170 West Tasman Drive San Jose CA 95134 1706 USA http www cisco com Tel 408 526 4000 800 553 NETS 6387 Fax 408 527 0883 THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE ALL STATEMENTS INFORMATION AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND EXPRESS OR IMPLIED USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California Berkeley UCB as part of UCB s public domain version of the UNIX operating system All rights reserved Copyright 1981 Regents of the University of California NOTWITHSTANDING ANY OTHER WARRANTY HEREIN ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED AS IS WITH ALL FAULTS CISCO AND THE ABOVE N
9. Driver installation may take a few moments Step3 Use your webcam to make video calls with your video calling application User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 18 l Accessories Jabra Handset 450 for Cisco Related Topics Mount your webcam on monitor on page 19 Mount your webcam on monitor Figure 10 Monitor mount Procedure Step1 Grasp the webcam as shown and open the flexible clip base with your other hand Step2 Mount the webcam making sure the foot on the flexible clip base is flush with the back of your monitor Step3 Adjust the camera angle up or down Jabra Handset 450 for Cisco The Jabra Handset 450 for Cisco was designed for Cisco for use in Cisco Unified Communications environments User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 I Accessories Jabra Handset 450 for Cisco Jabra Handset 450 features Table 5 Jabra Handset 450 features Feature Description Answer call Lift the handset If Cisco Jabber is running and you have no incoming active or held calls you can lift the handset to make it your active device The handset plays a beep tone when the device is ready and Cisco Jabber becomes the active window End call Place the handset back in the cradle Mute handset Press the mute button on the handset to toggle mute Handset volume control Press the Volume and Volume b
10. Selector can be hidden Click the up arrow in the notification area to show hidden icons User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 EEN l Accessories View your active camera or audio device You can also open Device Selector from Cisco Jabber by clicking Show on one of the following tabs e File gt Options gt Audio e File gt Options gt Video View your active camera or audio device You can check to see which of your cameras or audio devices is currently selected Procedure In the Windows notification area click D Check marks indicate the selected devices Change your active camera or audio device Use the Device Selector menu to select a different active camera or audio device Before You Begin You have multiple devices connected Procedure Step 1 In the Windows notification area click 2 Check marks indicate the selected devices Step2 Click a device camera or audio to make it active Step3 Click anywhere except on the Device Selector menu to close the menu Audio All audio from your Cisco Virtualization Experience Client and your hosted virtual desktop HVD plays through your selected audio device You can adjust the volume on the Cisco Virtualization Experience Client however each time you log on to your HVD the volume setting synchronizes with the setting on your HVD Adjust settings for Jabra Bluetooth devices All Jabra Bluetooth devices introd
11. Virtualization Experience Client 6215 Firmware Release 9 0 ai Accessories A Logitech Mouse M525 C F2 Start your default e mail application F3 Search for files and folders desktop search F4 Start the calculator F5 Switch between open applications F6 Bring the file browser to the front F7 Lock your Microsoft Windows desktop session F8 Toggle system audio mute and unmute F9 Start your default media player application F10 Play the previous track Media control F11 Toggle playback play and pause Media control F12 Play the next track Media control Set up your keyboard Procedure Step1 Power on your Cisco Virtualization Experience Client Step2 Plug the keyboard into a USB port on your Cisco Virtualization Experience Client To support the backlight feature on the Logitech UC Keyboard you must plug the keyboard directly into the Cisco Virtualization Experience Client or a powered USB hub What to Do Next If you experience issues with the keyboard plug it into a different USB port and restart the Cisco Virtualization Experience Client Logitech Mouse M525 C The wireless Logitech Mouse M525 C is designed for use with your Logitech UC Keyboard K725 C in Cisco Unified Communications environments User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 14 l Accessories Logitech Mouse M525 C i
12. ce is your headset and you lift the handset from the cradle the handset becomes the active device and plays the beep tone to indicate that it is ready The UC Keyboard indicates your new selection N Note You must be signed into Cisco Jabber Video resolution The only supported camera that features hardware encoding is the Logitech WebCam C920 C You must use this model camera with Cisco Jabber and Cisco Virtualization Experience Media Engine to support video resolutions up to 720p 720 horizontal lines and an aspect ratio of 16 9 at 30 frames per second in the virtual environment Other supported cameras only support video resolution up to 360p Numerous other variables such as network traffic or far endpoint video capability can affect video quality Note Do not switch from a high definition HD camera with hardware encoding to a standard definition camera during a call Video calls use the settings established at the start of the call The higher setting for the HD camera causes video performance issues with an SD camera If you want to switch to an SD camera do so between calls Screen lock call control While your hosted virtual desktop HVD is in screen lock you cannot make calls but you can receive them If you have an incoming call while your HVD is in screen lock you can use one of your accessories to answer the call With supported accessories the following call control features are available during scr
13. e next device in the Device Selector list becomes active When you have an incoming call an incoming call notification appears on your screen and your active audio device plays the ring tone Depending on your active device the Cisco Virtualization Experience Client built in speaker also plays the ring tone to ensure that you can hear it If the hands free speakerphone is the active device the ring tone plays on the speakerphone If the hands free speakerphone is not the active device or it is not connected both the active device and the Cisco Virtualization Experience Client built in speaker play the ring tone Note With some wireless headsets you may not hear the ring tone Some headsets play their own internal tone Device ready indicator If you perform one of the following off hook actions and you have no incoming or in progress calls the active device plays a beep tone to indicate that the device is ready The device becomes the active device if it was not already e Press the Call key on the Logitech UC Keyboard If the headset is the active device the beep plays on the Cisco Virtualization Experience Client built in speaker e Press the Call key on a headset e Press Speaker button on the Jabra Speak 450 e Lift the Jabra Handset 450 from its cradle User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 E Accessories Video resolution For example if your current active devi
14. e notification area click the Speaker icon Step2 Click Mixer Step3 Use the slider for Cisco Jabber to increase or decrease the volume User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 Accessories Default audio device selection i Default audio device selection Ring tone X When you start your Cisco Virtualization Experience Client for the first time the default audio device is the first device in the following order 1 Hands free if there are multiple hands free devices connected the default is the first device in alphabetical order 2 Headset if there are multiple headsets connected the default is the first headset in alphabetical order 3 Handset if there are multiple handsets connected the default is the first handset in alphabetical order 4 No devices connected the default audio device is the Cisco Virtualization Experience Client built in speaker The next time you start your Cisco Virtualization Experience Client the default audio device is the last selected active device provided the device is still connected Otherwise Device Selector makes the first available device active subject to the preceding order of selection After you connect a new device a New device found popup message appears in the notification area and the new device becomes the active device When you disconnect a device a Device disconnected popup message appears in the notification area and th
15. een lock e Answer call End call e Hold call e Resume call e Change active device Logitech UC Keyboard feature e Toggle audio mute e Toggle video start and stop Logitech UC Keyboard feature e Adjust audio volume User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 EEN l
16. et up for your network e Cisco AnyConnect page 5 e Citrix connection page 6 e VMware connection page 8 Cisco AnyConnect Cisco AnyConnect is virtual private network VPN software If you need to connect to your corporate network from a remote location you can use Cisco AnyConnect Your system administrator configures Cisco AnyConnect for you and provides your user name and password User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 E Connect to your hosted virtual desktop One time password One time password One time password OTP is an additional security feature that your system administrator can set up With OTP you generate a new password each time you connect to the virtual private network VPN by using AnyConnect The method of generating the OTP can vary for example some sites may use software tokens while others may use hardware tokens The deployment can differ as well according to the site security requirements The OTP may be the only password you require in which case you enter your OTP along with your user name Alternately you may be required to enter your user name and password and following a successful initial authentication be prompted to enter your OTP Enter your credentials as directed by your system administrator Connect to your corporate network Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Citrix conn Use Cisco AnyConnect to connect to your c
17. l two AA batteries Slide the lid for the storage compartment back into place On the bottom of the mouse move the OFF ON switch to the ON position Plug the Unifying Receiver into the USB port on your Logitech UC Keyboard as shown in the following image Figure 8 Plug in the Unifying Receiver Logitech WebCam C920 C amp The Logitech WebCam C920 C features hardware encoding and is designed for Cisco for use in Cisco Unified Communications environments With the Logitech WebCam C920 C Cisco Jabber with Cisco Virtualization Experience Media Engine can support video resolutions up to 720p 720 horizontal lines and an aspect ratio of 16 9 at 30 frames per second in the virtual environment Note Other variables such as network traffic or far endpoint video capability can affect video quality User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 E Accessories Logitech WebCam C920 C Logitech Webcam features Figure 9 Logitech WebCam C920 C features Table 4 Legend 1 Autofocus HD 1080p lens 2 Omni directional microphones Note The virtual environment does not use these microphones 3 Activity light 4 Flexible clip base 5 Privacy shutter 6 Tripod attachment Set up your webcam Procedure Step1 Place the webcam where you want it on a computer monitor desktop or tripod Step2 Connect the webcam to a USB port
18. nhanced functions items 2 through 11 are available only in Cisco Unified Communications environments To use these functions you must be signed in to Cisco Jabber Table 1 Legend 1 See the table Function keys which follows this legend E User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 Accessories Logitech UC Keyboard K725 C i Call your voicemail service Follow the audio prompts The key lights up red when you have a new voice message Note Ifyou have not set up Cisco Jabber with your Cisco Unity credentials for voicemail or if you use a third party voicemail system the message waiting indicator on the keyboard may not be in sync with Cisco Jabber Press to use your default handset for audio The name of your default handset device appears briefly on the LCD display Press to use your default headset for audio The name of your default headset device appears briefly on the LCD display Press to use your default hands free speakerphone device for audio The name of your default hands free device appears briefly on the LCD display See the LCD display for status information If your phone is registered your user name and number appear If your phone is not registered the message Phone is not registered appears For active calls the display shows the same information available from the Jabber call window such as caller ID and call timer The icons that ap
19. orporate network from a remote location Before You Begin At minimum you require a user name and password Depending on the network security you may require a one time password If you do not know your user name and password or know how to obtain your one time password contact your system administrator Enter your credentials as instructed by your system administrator Procedure If AnyConnect is not already started click ry to start AnyConnect From the Connect to menu choose the network to which you want to connect Click Connect Enter your user name and password and then click Connect Depending on the network security this password may be a one time password If you receive a prompt to enter your one time password obtain your one time password and enter it If you are not sure how to obtain your one time password check with your system administrator Click Connect Related Topics One time password on page 6 ection After you connect to the corporate network either directly or by using Cisco AnyConnect you can connect to your hosted virtual desktop HVD and use other network resources If your Cisco Virtualization Experience Client connects to your HVD over a Citrix XenDesktop connection or over a Citrix XenApp connection the log on page opens in Mozilla Firefox Your system administrator can place the shortcut icon for either User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0
20. pear depend on the status of the call active on hold or microphone muted You can adjust the brightness and the contrast for the LCD display Press FN and the Volume or Volume key to adjust the brightness for the LCD display Press FN Alt and the Volume or Volume key to adjust the contrast for the LCD display Press to place a call on hold or to resume a held call Press to answer an incoming call or to end your current active call If you do not have any incoming active or held calls you can press this key to bring make Cisco Jabber the active window Your active device plays a beep to indicate that it is ready The Cisco Virtualization Experience Client speaker plays the beep if your active device is a headset Cisco Jabber must be running Press to toggle your video add or remove video for a call in progress Press to toggle audio mute and unmute audio for a call in progress Note Thbis feature is not available if you connect to your HVD over a VMware connection Press the Volume or Volume key to increase or decrease Cisco Jabber audio volume Note This feature is not available if you connect to your HVD over a VMware connection The following table lists the default functions for each of the Function Keys F keys Simultaneously press the FN key and the F key that you want to use Table 2 Function keys F1 Start your default web browser User Guide for Cisco
21. ser Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 I Your Cisco virtual environment Your Cisco Virtualization Experience Client e Logitech UC Keyboard K725 C e Logitech Mouse M525 C e Logitech Webcam C920 C e Jabra Handset 450 Cisco e Jabra Speak 450 Cisco Your Cisco Virtualization Experience Client Your Cisco Virtualization Experience Client is preinstalled with Virtualization Experience Client firmware and all required software is already set up for you With Cisco Virtualization Experience Client you use Citrix ICA opens in Mozilla Firefox Citrix XenClient or VMware Horizon View Client to sign into your hosted virtual desktop N Note To access your corporate network you may need to connect by using Cisco AnyConnect If your system administrator installed the optional Cisco Virtualization Experience Media Engine VXME you can also place calls with Cisco Jabber on your hosted virtual desktop For more information about Cisco Jabber see http www cisco com en US products ps12862 products_user_guide_list html The following image shows the Cisco Virtualization Experience Client with a monitor and the designed for Cisco accessories 346619 User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 2 l Your Cisco virtual environment Your Cisco Virtualization Experience Client i Figure 1 Cisco Virtualization Experience Client and Acces
22. sories Legend 1 Logitech Webcam C920 C wired 2 Cisco Virtualization Experience Client 6215 wired thin client 3 Logitech Wireless Mouse M525 C wireless 4 Logitech UC Keyboard K725 C wired 5 Jabra Speak 450 Cisco wired or Bluetooth 6 Jabra Handset 450 Cisco wired Related Topics Accessories on page 11 User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 I Your Cisco virtual environment Your Cisco Virtualization Experience Client User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 oa l L Note CHAPTER Connect to your hosted virtual desktop To connect to your hosted virtual desktop HVD you must first connect to your corporate network If you do not connect to the network directly you must use Cisco AnyConnect Your system administrator can provide advice as to whether you must use Cisco AnyConnect before you can log on to your HVD or access other network resources If you must use Cisco AnyConnect your administrator can set it to start automatically when you boot and can place the Cisco AnyConnect shortcut on your Cisco Virtualization Experience Client desktop After you connect to the corporate network you log on to your HVD by using one of the following methods e Citrix XenDesktop opens in Mozilla Firefox e Citrix XenClient e VMware Horizon View Client You must use the connection method s
23. than those made for Cisco the behavior of these devices may be different than described in this document The following accessories are made for Cisco and supported for use with Cisco Virtualization Experience Media Engine e Logitech UC Keyboard K725 C e Logitech Mouse M525 C e Logitech Webcam C920 C e Jabra Handset 450 for Cisco e Jabra Speak 450 for Cisco User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 I Accessories Logitech UC Keyboard K725 C amp Note Cisco does not provide support for these accessories For more information about or technical assistance with your Logitech accessories visit the Logitech website http www logitech com e Jabra accessories visit the Jabra website http www jabra com Related Topics Logitech UC Keyboard K725 C on page 12 Logitech Mouse M525 C on page 14 Logitech WebCam C920 C on page 17 Jabra Handset 450 for Cisco on page 19 Jabra Speak 450 for Cisco on page 22 Logitech UC Keyboard K725 C The Logitech UC Keyboard K725 C is designed for Cisco for use in Cisco Unified Communications UC environments The Logitech UC Keyboard features Cisco UC integration with Cisco Jabber Logitech UC Keyboard features Figure 5 Logitech UC Keyboard features Logitech a a L o e lis Cala fa fa Celtel CCPC eI lle JC IG en L Note E
24. uce a short delay in bringing up the audio path about 1 3 seconds With the latest firmware the Jabra Speak 450 for Cisco does not have this issue For other supported Jabra Bluetooth devices such as Jabra Pro you can eliminate the delay by changing the device settings in the Jabra PC Suite User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 I Accessories A Adjust Virtual Experience Client volume Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 Before You Begin Jabra PC Suite must be installed Procedure Open the Jabra Control Center Click the Jabra device for which you want to modify the settings Click Softphone PC Check Open phone line on undock Under PC audio control click Automatic From the Softphone vendor list select Other Click Apply Adjust Virtual Experience Client volume You can adjust the volume for the Cisco Virtualization Experience Client when you are not signed into your hosted virtual desktop HVD After you sign into your HVD the volume setting on the Cisco Virtualization Experience Client synchronizes with the volume setting for Cisco Jabber on the HVD Procedure Step1 Inthe notification area click the Speaker icon Step2 Use the slider to increase or decrease the volume Adjust Jabber volume You can adjust the volume settings for certain applications on your hosted virtual desktop HVD including Cisco Jabber Procedure Step1 In th
25. uttons on the handset to increase or decrease the volume J User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 Accessories Feature Jabra Handset 450 for Cisco Description Handset status indicator light Indicates the handset status The light is e White not flashing when the handset is ready but not in use e White flashing when the handset is charging but not in use e Yellow when the handset battery is low e Blue flashing when the handset is pairing with the cradle If the handset flashes blue while away from the cradle this indicates that the handset is out of range Red flashing when you have an incoming call and the handset is ringing e Red not flashing when you have new voicemail Note Ifyou have not set up Cisco Jabber with your Cisco Unity credentials for voicemail or if you use a third party voicemail system the message waiting indicator on the handset may not be in sync with Cisco Jabber e Green when you have an active call or audio stream Sk S Sy Handset charging Place the handset into the cradle Handset paired with cradle The handset and cradle are factory paired To pair a new handset with the cradle place the new handset into the cradle Note You can pair only one handset with the cradle at a time Set up your handset The Jabra Handset 450 for Cisco and the handset cradle are factory paired
26. ware Horizon View Client to start when you boot the Cisco Virtualization Experience Client J User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 Connect to your hosted virtual desktop VMware connection i You require a username and password to connect to your HVD If you do not know your username and password contact your system administrator Figure 4 VMware Horizon View Client log on gy VMware View Client ja 3 Eile Desktop View Help vmware View Client Connect to Server Enter your user name and password A https eas view domain com View Co Enter the hitps eas view domai Usemame hm Always connect Password COPCoIP Q cancel Domain DOMAIN M 346653 User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 I Connect to your hosted virtual desktop a VMware connection User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 10 l CHAPTER 3 Accessories e Cisco approved audio and video accessories page 11 e Device Selector page 24 e Audio page 25 e Video resolution page 28 e Screen lock call control page 28 Cisco approved audio and video accessories For a complete listing of supported audio and video accessories see Cisco Virtualization Experience Client 6215 Cisco Approved Audio and Video Accessories Data Sheet Note If you use supported accessories other
27. xperience Media Engine 1 Your Cisco Virtualization Experience Client 2 CHAPTER 2 Connect to your hosted virtual desktop 5 Cisco AnyConnect 5 One time password 6 Connect to your corporate network 6 Citrix connection 6 VMware connection 8 CHAPTER 3 Accessories 11 Cisco approved audio and video accessories 11 Logitech UC Keyboard K725 C 12 Logitech UC Keyboard features 12 Set up your keyboard 14 Logitech Mouse M525 C 14 Logitech Wirelesss Mouse features 15 Set up your mouse 16 Logitech WebCam C920 C 17 Logitech Webcam features 18 Set up your webcam 18 Mount your webcam on monitor 19 Jabra Handset 450 for Cisco 19 Jabra Handset 450 features 20 Set up your handset 21 User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 Contents Power your handset off and on 22 Jabra Speak 450 for Cisco 22 Jabra Speak 450 features 23 Set up your hands free speakerphone USB connection 24 Set up your hands free speakerphone Bluetooth connection 24 Device Selector 24 View your active camera or audio device 25 Change your active camera or audio device 25 Audio 25 Adjust settings for Jabra Bluetooth devices 25 Adjust Virtual Experience Client volume 26 Adjust Jabber volume 26 Default audio device selection 27 Ring tone 27 Device ready indicator 27 Video resolution 28 Screen lock call control 28 E User Guide for Cisco Virtualization Experience Client 6215 Firmware Release 9 0 CHAPTER 1 Your
Download Pdf Manuals
Related Search