BPN-SAS3-116A BAckPlANe USeR'S GUIDe
Contents
1. SUPERMICR BPN SAS3 116A BACKPLANE USER S GUIDE 1 0a The information in this User s Manual has been carefully reviewed and is believed to be accurate The vendor assumes no responsibility for any inaccuracies that may be contained in this document makes no commitment to update or to keep current the information in this manual or to notify any person or organization of the updates Please Note For the most up to date version of this manual please see our web site at www supermicro com Super Micro Computer Inc Supermicro reserves the right to make changes to the product described in this manual at any time and without notice This product including software if any and documentation may not in whole or in part be copied photocopied reproduced translated or reduced to any medium or machine without prior written consent IN NO EVENT WILL SUPERMICRO BE LIABLE FOR DIRECT INDIRECT SPECIAL INCIDENTAL SPECULATIVE OR CONSEQUENTIAL DAMAGES ARISING FROM THE USE OR INABILITY TO USE THIS PRODUCT OR DOCUMENTATION EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES IN PARTICULAR SUPERMICRO SHALL NOT HAVE LIABILITY FOR ANY HARDWARE SOFTWARE OR DATA STORED OR USED WITH THE PRODUCT INCLUDING THE COSTS OF REPAIRING REPLACING INTEGRATING INSTALLING OR RECOVERING SUCH HARDWARE SOFTWARE OR DATA Any disputes arising between manufacturer an2. Revision 1 0a Release Date March 02 2015 Unless you request and receive written permission from Super Micro Computer Inc you may not copy any part of this document Information in this document is subject to change without notice Other products and companies referred to herein are trademarks or registered trademarks of their respective companies or mark holders Copyright 2015 by Super Micro Computer Inc All rights reserved Printed in the United States of America Contents Contents Contacting Supermicro Returning Merchandise for Service V Chapter 1 Guidelines 1 1 ESD Safety Guidelines dada Rt tere c erede Al Ak 1 1 1 2 General Safety Guideliries 2 ei rei ka aa nan ALA band n ar n 1 1 1 3 Version Information Chapter 2 Connectors Jumpers and LEDs 2 1 Rear Connectors im UK AES 2 1 2 2 Rear Connector Definitions 2 2 259 Bear JUMPOR EH 2 3 Expla ation of JUMPS sna wy yy dz ordeo 2 3 2 4 Front Connectors and LED Indicators six yi xalka dillan ad y a kakila kana zak ki an 2 4 BPN SAS3 116A Backplane Manual Contacting Supermicro Headquarters Address Super Micro Computer Inc 980 Rock Ave San Jose CA 95131 U S A Tel 1 408 503 8000 Fax 1 408 503 8008 Email marketing supermicro com General Information support supermicro com Technical Support Web Site www supermicro com
3. of the connector Pin 1 is identified with a square solder pad on the printed circuit board Note On two pin jumpers Jumper IN Closed means the jumper is on and Setting Open means the jumper is off the pins 2 3 BPN SAS3 116A Backplane Manual 2 4 Front Connectors and LED Indicators Connectors for SAS drive numbers 0 through 7 are SAS3 SAS 8 and 9 support SAS2 a a a A A sAS 0 LED11 SAS 2 LED13 6 4 5 SAS 6 LED17 S S g LED19 LED1 LED3 LED5 LED7 LED9 Figure 2 3 Front Connectors and LEDs Front SAS SATA Connectors and LED Indicators HDD Activity LED Failure LED Drive Number Label blue red SAS 0 J1 LED11 LED1 SAS 1 J2 LED12 LED2 SAS 2 Ja LED13 LED3 SAS 43 34 LED14 LED4 SAS 4 J5 LED15 LEDS SAS 5 Je LED16 LED6 SAS 6 37 LED17 LED7 SAS 7 us LED18 LED8 SAS 8 Je LED19 LED9 SAS 9 1 LED20 LED10 2 4 Chapter 2 Connectors Jumpers and LEDs Notes BPN SAS3 116A Backplane Manual Disclaimer cont The products sold by Supermicro are not intended for and will not be used in life support systems medical equipment nuclear facilities or systems aircraft aircraft devices aircraft emergency communication devices or other critical systems whose failure to perform be reasonably expected to result in signif
4. Europe Address Super Micro Computer B V Het Sterrenbeeld 28 5215 ML s Hertogenbosch The Netherlands Tel 31 0 73 6400390 Fax 31 0 73 6416525 Email sales supermicro nl General Information support supermicro nl Technical Support rma gsupermicro nl Customer Support Web Site www supermicro nl Asia Pacific Address Super Micro Computer Inc 3F No 150 Jian 1st Rd Zhonghe Dist New Taipei City 235 Taiwan R O C Tel 886 2 8226 3990 Fax 886 2 8226 3992 Email support supermicro com tw Web Site www supermicro com tw Contents Returning Merchandise for Service A receipt or copy of your invoice marked with the date of purchase is required before any warranty service will be rendered You can obtain service by calling your vendor for a Returned Merchandise Authorization RMA number When returning to the manufacturer the RMA number should be prominently displayed on the outside of the shipping carton and mailed prepaid or hand carried Shipping and handling charges will be applied for all orders that must be mailed when service is complete For faster service RMA authorizations may be requested online http www supermicro com support rma Whenever possible repack the backplane in the original Supermicro box using the original packaging materials If these are no longer available be sure to pack the backplane in an anti static bag and inside the box Make sure that there is enough packagi
5. d customer shall be governed by the laws of Santa Clara County in the State of California USA The State of California County of Santa Clara shall be the exclusive venue for the resolution of any such disputes Super Micro s total liability for all claims will not exceed the price paid for the hardware product FCC Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the manufacturer s instruction manual may cause harmful interference with radio communications Operation of this equipment in a residential area is likely to cause harmful interference in which case you will be required to correct the interference at your own expense California Best Management Practices Regulations for Perchlorate Materials This Perchlorate warning applies only to products containing CR Manganese Dioxide Lithium coin cells Perchlorate Material special handling may apply See www dtsc ca gov hazardouswaste perchlorate WARNING Handling of lead solder materials used in this product may expose you to lead a chemical known to the State of California to cause birth defects and other reproductive harm Manual
6. e backplane See the table on the right for pin definitions 2 CPLD Upgrade Port The JP23 connector is used only by manufacturing to upgrade firmware 3 Sideband Connector This is the sideband connector for SAS2 and is designated T SGPIO1 4 SAS2 Connectors The SAS2 connectors are designated JS1 SAS2 in 1 and JS2 SAS2 in 2 Pins are defined according the SAS standard 5 SAS3 Connectors JSM1 and JSM2 provide connections for the SAS drive cables Pins are defined according the SAS standard 2 2 Main Power 4 Pin Connector Pin Definition il 12V 2 and 3 Ground 4 5V Sideband Connector T SGPIO1 Pin Definition Pin Definition 2 SDataln 1 NC SGPIO Data In 4 SDataOut 3 GND SGPIO Data Out 6 GND 5 SLoad SGPIO Load 8 N C 7 SClock SGPIO Clock Chapter 2 Connectors Jumpers and LEDs 2 3 Rear Jumpers 8 O ew img Dg PE amy E a J11 J12 Figure 2 2 Rear Jumpers Jumper Settings Jumper Settings Note JP1 Pins 1 2 default Used only by manufacturing JP2 Open1 Not used JAKI PA Open Reserved for future Explanation of Jumpers modify the operation of the backplane ores e e jumpers can be used to choose between optional settings Jumpers create shorts between two pins to change the function
7. g or removing any cables from the backplane Make sure that the backplane is securely and properly installed on the motherboard to prevent damage to the system due to power shortage 1 1 BPN SAS3 116A Backplane Manual 1 3 Version Information The BPN SAS3 116A backplane has been designed to utilize the most up to date technology available providing your system with reliable high quality performance This manual reflects BPN SAS3 116A Revision 1 10 the most current release available at the time of publication Refer to the Supermicro Web site at www supermicro com for the latest updates compatible parts and supported configurations 1 2 Chapter 2 Connectors Jumpers and LEDs Chapter 2 Connectors Jumpers and LEDs This manual covers BPN SAS3 116A 2 1 Rear Connector Locations The following connectors are on the side of the backplane that faces the rear of the chassis They are marked by silkscreen labels 3 is J COWES 158 gt gt fmad Figure 2 1 Rear Connector Locations 1 Power Connectors JPW1 JPW2 4 SAS2 Connectors JS1 and JS2 4 pin 5 SAS3 Connectors JSM1 JSM2 2 CPLD programming port J23 6 pin 3 Sideband Connector T SGPIO1 6 pin 2 1 BPN SAS3 116A Backplane Manual 2 2 Rear Connector Definitions 1 Backplane Main Power Connectors The 4 pin connectors designated JPW1 and JPW2 provide power to th
8. icant injury or loss of life or catastrophic property damage Accordingly Supermicro disclaims any and all liability and should buyer use or sell such products for use in such ultra hazardous applications it does so entirely at its own risk Furthermore buyer agrees to fully indemnify defend and hold Supermicro harmless for and against any and all claims demands actions litigation and proceedings of any kind arising out of or related to such ultra hazardous use or sale 2 6
9. ng material surrounding the backplane so that it does not become damaged during shipping This warranty only covers normal consumer use and does not cover damages incurred in shipping or from failure due to the alteration misuse abuse or improper maintenance of products During the warranty period contact your distributor first for any product problems BPN SAS3 116A Backplane Manual Notes vi Chapter 1 Guidelines Chapter 1 Guidelines This chapter offers guidelines for personal and equipment safety and notes about the BPN SAS3 116A version documented in this manual 1 1 ESD Safety Guidelines Electrostatic Discharge ESD can damage electronic components To prevent damage to your system it is important to handle it very carefully The following measures are generally sufficient to protect your equipment from ESD Use a grounded wrist strap designed to prevent static discharge Touch a grounded metal object before removing a component from the antistatic bag Handle the backplane by its edges only do not touch its components peripheral chips memory modules or gold contacts When handling chips or modules avoid touching their pins Put the card and peripherals back into their antistatic bags when not in use General Safety Guidelines Always disconnect power cables before installing or removing any components from the computer including the backplane Disconnect the power cable before installin
Download Pdf Manuals
Related Search