User Guide OPTIDRIVE HVAC RELAY OPTION
Contents
1. Relay 2 contacts 10V O P n Digital I P 1 9 Digital I P 2 Digital I P 3 a 10V O P o Analog I P Relay contact Relay common oy oh h 500 Q min Relay 1 contacts i oa 0 10VanalogO P Analog I P Closed A Open V Oo o gt D O wT og eo Cc O32 2 O O ee Cite C aA O lt a Os oO 3 ke O Optidrive size 2 Option PCB inserted into Optidrive control terminal strip All 11 terminal screws on the Optidrive must be tightened to ensure good electrical contact and correct functionality OPTION MODU E CONTROL TERMINALS Relay 2 contacts nO vO gt O a gt E O of V 0 Digital Input 1 OV Digital Input 2 Digital Input 3 10V Out Analog Input 1 Analog Output OV oo Relay contact oO _ _ Relay common Analog inputs should be connected to terminals 6 amp 72. Immunity Standard Industrial Level Enclosure ingress protection EN60529 IP00 NEMA 250 Flammability rating according to UL 94 Offa s Dyke Business Park CAUTION e Store the Option in its box until required It should be stored in a clean and dry environment Temperature range 40 C to 60 C Install the Option onto the Optidrive by inserting the row of 11 pins into the terminal connector of the Optidrive ensuring that the terminals are tightened If the Option is being used with Size 1 Optidrive care should be taken to support the Option when the terminal screws of the Option are being tightened or loosened WARNING e Optidrives and the Options should be installed only by qualified electrical persons and in accordance with local and national regulations and codes of practice Electric shock hazard Disconnect and ISOLATE the Optidrive before attempting any work on it High voltages are present at the terminals and within the drive for up to 10 minutes after disconnection of the electrical supply Where the electrical supply to the drive is through a plug and socket connector do not disconnect until 10 minutes have elapsed after turning off the supply as Low Voltage Directive 664 1 Insulation Coordination within Low Voltage Systems email enquiry invertek co uk Internet www invertek co uk EXPLANATION The HVAC Relay Option Module can be used in applications where two indi
3. SAFETY NOTICES WARNING is given where there is a hazard that could lead to injury or death of personnel CAUTION is given where there is a hazard that could lead to damage to equipment It is the responsibility of the installer to ensure that the equipment or system into which the product is incorporated complies with the EMC legislation of the country of use Within the European Union equipment into which this product is incorporated must comply with 89 336 EEC Electromagnetic Compatibility WARNING Within the European Union all machinery in which this product is used must comply with the Directive 89 392 EEC Safety of Machinery In particular the equipment should comply with EN60204 1 INVERTER DRIVES www invertek co uk OPTIDRIVE HVAC RELAY OPTION MODULE WARRANTY Complete Warranty Terms and Conditions are available upon request fro your IDL Authorised Distributor ANDARDS jpti ve fitted All rights reserved No part of t stan rds transmitted in any form or by ar including photocopying recording or by an retrieval system without permission in writing fro Copyright Invertek Drives Ltd 2 The manufacturer accepts no liability for any cons N enc from inappropriate negligent or incorrect installation lt a The contents of this User Guide are believed to be correct at the yy f printing In the interests of a commitment to a policy of co S
4. cators are required showing drive running and drive tripped Product Suitability There are 2 variants of this option The correct variant must be used with the following products Optidrive OD HVACO IN Optidrive E ODE HVACO IN OPERATION Programming the first relay output For typical operation set P 18 1 eg Relay 2 closed on enable Drive running Green Light Relay 1 closed when drive tripped Red Light Use the following information to set P 18 for other types of Relay output Since the first relay output fitted within the Optidrive is programmed using P 18 in the Optidrive two completely independent relay outputs are available The following options are supported for Relay 1 P 18 0 Relay 1 closed when Optidrive disabled P 18 1 Relay 1 closed when Optidrive tripped P 18 2 Relay 1 closed when Optidrive output not at set requested speed P 18 3 Relay 1 closed when Optidrive output is at zero speed P 18 4 Relay 1 closed when Optidrive output is not at maximum speed P 18 5 Relay 1 closed when Optidrive output is not in overload Programming the second relay output The second relay output has only one practical setting When P 18 1 Relay 2 is closed when Optidrive is running SPECIFICATIONS Max Relay switching voltage 250V AC 220V DC Max Relay switching current 1A Max input voltage 50V DC Environmental 10 C 50 C Conformity IP00 UL94V 0 OPTION COMPONENT LAYOUT
5. improvement the manufacturer reserves the right to chang specification of the product or its performance or the contents of the User Guide without notice SAFETY This option is specifically designed to be used with the Optidrive variable speed drive product and is intended for professional incorporation into complete equipment or systems If installed incorrectly it may present a safety hazard The Optidrive uses high voltages and currents carries a high level of stored electrical energy and is used to control mechanical plant that may cause injury Close attention is required to system design and electrical installation to avoid hazards in either normal operation or in the event of equipment malfunction Invertek Drives Ltd Welshpool Powys SY21 8JF UK System design installation commissioning and maintenance must be carried out only by personnel who have the necessary training and experience They must read carefully this safety information and the instructions in this Guide and follow all information regarding transport storage installation and use of the Option module including the specified environmental limitations Tel 44 0 1938 556868 Fax 44 0 1938 556 869 Please read the IMPORTANT SAFETY INFORMATION below and all Warning and Caution boxes elsewhere Part No 82 HVACO IN Iss 1 00 Y hs op Option complies with the EN50081 2 EMC Generic Emissions Standard Industrial Level EN50082 2 EMC Generic
Download Pdf Manuals
Related Search