User Guide
Contents
1. Hd Focus Adjust HCE Self Test nr Fixture Hours r Stk Reset GU d and St H only for color change MID DMX512 Address Setting Press the MENU button up to when the MD is showing on the display Pressing ENTER button and the displav will blink Use DOWN and UP button to change the DMX512 address Once the address has been selected press the ENTER button to setup or automaticallv return to the main functions without anv change after 8 seconds To go back to the functions without anv change press the MENU button again 7 7 E Slave Mode Press the MENU button up to when the SL fd is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the normal or 2 light show mode or 8 light show mode or 4 light show Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again l IL TI Blackout Mode is showing on the display Pressing ENTER button and Press the MENU buiton up to when the the display will blink Use DOWN and UP button to select the an yes blackout or 7 on no blackout mode Once the mode has been2. Disconnect main power before fuse lamp replacement or servicing Replace fuse lamp only with the same type Do not use any other type of lamp Make sure there is no flammable materials close to the unit while operating as it is fire hazard Use safety cable when fixes this unit Don t handle the unit by taking its head only but always by taking its base Maximum ambient temperature is TA 40 C Don t operate it where the temperature is higher than this Unit surface temperature may reach up to 85C Don t touch the housing bare hand during its operation Turn off the power and allow about 15 minutes for the unit to cool down before replacing bulb or serving as the unit could be very hot In the event of serious operating problem stop using the unit immediately Never try to repair the unit by yourself Repairs carried out by unskilled people can lead to damage or malfunction Please contact the nearest authorized technical assistance center Always use the same type spare parts Don t connect the device to any dimmer pack or power pack Donot touch any wire during operation as high voltage might be causing electric shock Warning To prevent or reduce the risk of electrical shock or fire do not expose the unit to rain or moisture Never touch bulb with bare fingers as it is very hot after using Hot lamp explosion hazard Do not open the unit within five minutes after switching off Do not start on the unit without b
3. Remote controller input By connect to the 1 4 microphone jack to control the unit for Stand by Function and Mode Sensitivity To adjust the sound sensitivity Microphone To receives audio signal for sound activation DMX input output For DMX512 link use 3 pin XLR plug cable to link the unit together 4 2 Main Function To select any of the given functions press the MENU button up to when the required one is showing on the display Select the function by ENTER button and the display will blink Use DOWN and UP button to change the mode Once the required mode has been selected press the ENTER button to setup or it will automatically return to the main functions without any change after idling 8 seconds To go back to the functions without any change press the MENU button The main functions are showing below Mode DMX512 Address Setting Slave mode Normal Slave mode 2 Light Show Slave mode 3 Light Show Slave mode 4 Light Show oo Blackout Mode Yes Blackout hn Blackout Mode No Blackout nc Normal Color 5i Split Color CO Pan Normal i Pan Inversion l b l FIDI Tilt Barrel Normal roe i Tilt Barrel Inversion nna Dimmer Normal Dimmer Inversion LED on LED off GD Display Normal Display Inversion m r MENU
4. DMX controller 5 Check in the DMX cables run near or run alongside to high voltage cables that may cause damage or interference to DMX interface circuit C Some units don t respond to the easy controller 1 You may have a break in the DMX cabling Check the LED for the response of the master slave mode signal 2 Wrong DMX address in the unit Set the proper address D No response to the sound 1 Make sure the unit that does not receive DMX signal 2 Check microphone to see if it is good by tapping the microphone E One of the channels is not working well 1 The stepper motor might be damaged or the cable connected to the PCB is broken 2 The motor s drive IC on the PCB might be out of condition F The lamp is cutting out intermittently 1 The lamp is not working well Check the main voltage either too high or too low 2 Internal temperature may be too high Check and if necessary replace the fan on the head 16 16 7 Maintenance and Cleaning Maintenance Ballast Ignitor capacitor A As the pictures shown above if the cable or cable joints turned yellow or black please replace the cable or cable joints immediately B Do maintain the fixtures every two months and make sure that all the screws and terminals have been locked firmly to make sure the normal performance of the fixtures Negligence of maintenance would cause malfunction of the fixture Cleaning The cleaning of internal and external optical lenses and or m
5. effet 088 105 Orange Yellow 096 1060 deich 091 097 Orange 135 Slowest speed clockwise 0856 095 Light Green 075 085 UV Purple 064 074 Blue 054 063 Red 043 053 Amber 032 042 Light Blue 022 031 Magenta 011 021 Green 000 010 White 083 090 Light Green Orange 076 082 Light Green 068 075 UV Purple 061 067 Blue 053 060 Red Blue 046 052 Red 038 045 Amber 031 037 Light Blue 023 030 Magenta 016 022 GreentMagenta 008 015 Green 000 007 White 14 121 134 Stopped 120 Slowest speed counterclockwise a 010 Fastest speed counterclockwise 000 009 Stopped 14 5 6 DMX512 Connection The DMX512 is widely used in intelligent lighting control with a maximum of 512 channels DMX512 COMMON 120 ohm 1 4W DMX INPUT OUTPUT DMX Termination reduces signal errors and to avoid signal transmission problems and interference It is always advisable to connect a DMX terminal Resistance 120 ohm 1 4W between pin2 DMX and pin3 DMX of the last fixture 1 1f you using a controller with 5 pins DMX output you need to use a 5 to 3 pin adapter cable 2 At last unit the DMX cable has to be terminated with a terminator Solder a 120 ohm 1 4W resistor between pin 2 DMX and pin 3 DMX r into a 3 pin XLR plug and plug it in the DMX output of the last unit 3 Connect the unit together in a daisy chain by XLR plug from the output of the unit to the input of the next unit The cable can not branche
6. selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again l Color Mode Press the MENU button up to when the Lid is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 710 normal or IL split color mode Once the mode has been selected press the ENTER button to setup or automaticallv return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Pan Inversion Press the MENU button up to when the i PHA jg showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 0 normal or pan inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Tilt Inversion Barrel Rotation Inversion Press the MENU button up to when the HELE roc is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 10 normal or tilt barrel rotation inversion
7. 10 5 2 Easy Controller The easy remote control is used only in master slave mode By connecting to the 1 4 microphone jack of the first unit you will find that the remote control on the first unit will control all the other units as below Built in lighting shows triggered by Easy Controller Stand by Blackout the unit IR 5S HID Function Strobe X Y moving pattern selection Color Gobo selection X Y moving setting IR 5B HID 1 Gobo Color sync strobe 12 patterns 1 Hold on for gobo change 1 Pan position 2 Svnc strobe 2 Press shortly for color 2 Tilt position 3 Two light strobe change 3 Dimmer Mode Sound 1 Sound 2 Slow Sound 3 Position Latch LED off LED normal blinking LED on LED fast blinking Stand Stand by Blackout the unit IR 4C HID Function Strobe Chase pattern selection Color Gobo selection Dimmer setting 1 Gobo Color sync strobe 6 patterns 1 Hold on for gobo change 2 Svnc strobe 2 Press shortly for color 3 Two light strobe change Mode Sound 1 Sound 2 Slow Latch LED off LED normal blinking LED on LED fast blinking IS 6S HID Stand Stand by Blackout the unit IS 6B HID Function Strobe X Y moving pattern selection Color Gobo selection X Y moving setting 1 Gobo Color sync strobe 12 patterns 1 Hold on for gobo change 1 Pan position 2 Sync strobe 2 Press shortly for color 2 Tilt position 3 Two light strobe change Mode Sound 1 Sound 2 Slow Sound 3 Posit
8. Z Solution Your integrated Solution LINKABLE Ce STAND ALONE iShow 6S HID iShow 6B HID iShow 4 HID User Guide Professional Entertainment Technology D f TABLE OF CONTENTS Safety Instruction Technical Specification 2 1 Inserting Exchanging rotating gobos 2 2 Beam Angle Lamp How To Set The Unit 4 1 Control Panel 4 2 Main Function How To Control The Unit 5 1 Master Slave Built In Preprogrammed Function 5 2 Easy Controller 5 3 ISolution Operation Universal DMX Controller 5 4 Universal DMX Controller 5 5 DMX512 Configuration 5 6 DMX512 Connection Troubleshooting Maintenance and Cleaning 1 Safety Instruction Please read carefully the instruction which includes important N information about installation operation and maintenance WARNING Please keep this User Guide for future consultation If you sell the unit to another user be sure that they also receive this user guide Unpack and check carefully there is no transportation damage before using the unit Before operating ensure that the voltage and frequency of power supply match the power requirements of the unit It s important to ground the yellow green conductor to earth in order to avoid electric shock The unit is for indoor use only Use only in a dry location The unit must be installed in a location with adequate ventilation at least 50cm from adjacent surfaces Be sure that no ventilation slots are blocked
9. cooling Pan 180 deg Tilt 70 deg IR 5S HID IR 5B HID IS 6S HID IS 6B HID c R 5S HID IR 5B HID Independent gobo wheel with 14 gobos plus open and blackout including 11 metal 2 glass and 1 effect gobos with shaking effect Independent color wheel with 11 dichroic colors with rainbow effect and independent shutter o IR AC HID Independent gobo wheel with 14 gobos plus open and blackout including 8 metal 1 effect 1 frost 2 glass gobos and 2 color temperature filters 5600k amp 3200k with shaking effect Independent color wheel with 11 dichroic colors with rainbow effect and independent shutter amp dimmer o S 6S 6B 4 HID Professional multi gobo rotator 14 gobos plus open and blackout including 11 metal 2 glass and 1 effect gobos with shaking and shutter effect Independent color wheel with 11 dichroic colors with rainbow effect 2 2 Beam Angle IR A4C HID Gaam anpnie i degree 5730 1490 785 lux IR BS EB HID Beam angie 16 degree Distance m IS d HID Beam angle 25 degree Distance m j AN 8 m RI 8 piss pm Distance m In case of replacement of the lamp or maintenance do not open the N fixture within 15 minutes until the unit cools down after switching off HID 150W 1 Always switch off the main supply and never handle the lamp or luminaries when is hot 2 Do not touch the bulb with bare hands If this happens clean the lamp with denatured alcohol and wipe
10. d or split to a X cable DMX512 is a very high speed signal Inadequate or damaged cables soldered joints or corroded connectors can easily distort the signal and shut down the system 4 The DMX output and input connectors are pass through to maintain the DMX circuit when power is disconnected to the unit 5 Each lighting unit needs to have an address set to receive the data sent by the controller The address number is between 0 511 usually O amp 1 are equal to 1 6 The end of the DMX512 system should be terminated to reduce signal errors 7 3 pin XLR connectors are more popular than 5 pin XLR 3 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 5 pin XLR Pin 1 GND Pin 2 Negative signal Pin 3 Positive signal 15 15 6 Troubleshootino Following are a few common problems that may occur during operation Here are some suggestions for easy troubleshooting A The unit does not work no light and the fan does not work 1 Check the connect power and main fuse 2 Measure the mains voltage on the main connector 3 Check the power on LED B Not responding to DMX controller 1 DMX LED should be on If not check DMX connectors cables to see if link properly 2 If the DMX LED is on and no response to the channel check the address settings and DMX polarity 3 If you have intermittent DMX signal problems check the pins on connectors or on PCB of the unit or the previous one 4 Try to use another
11. ease refer to the user guide of iLead controller or universal DMX controller No need to turn the unit off when you change the DMX address as new DMX address setting will be effected at once Every time you turn the unit on it will show its item number on the display and move all the motors to their home position and you may hear some noises for about 20 seconds After that the unit will be ready to receive DMX signal or run the built in programs 5 1 Master Slave Built In Preprogrammed Function By linking the units in master slave connection the first unit will control the other units to give an automatic sound activated synchronized light show This function is good when you want an instant show Its DMX input jack will have nothing plugged into it and Its master LED will be constantly on and sound LED will flash to the music The other units will have to set in slave mode DL UG and select Li l CI normal or 24 2 light show mode BL 3l 3 light show mode or 4 light show Their DMX cables plugged into the DMX input jacks daisv chain and the slave led lights will constantiv on and oniv for color change 2 light show In Sind slave mode 3L li means the unit works normally and oL E means 2 light show In order to create a great light show you can set 2L C onthe second unit to get contrast movement to each other even if you have two units only 10
12. ically store after 8 seconds Or press the ENTER button again return to the mode l dar display normal To go back to the functions press the MENU button again Or Display normal mode for the fixture putting on the floor JECD B A M Ma Display inversion mode for the fixture fixing under ceiling LI VILLI Focus Adjust Press the MENU button up to when the Hu is blinking on the display Pressing ENTER button the unit will focus on center position To go back to the functions press the MENU button again E I JL Self Test Press the MENU button up to when the ED is blinking on the display Pressing ENTER button and the unit will run self test by built in program To go back to the functions press the MENU button again Fixture Hours Press the MENU button up to when the l is blinking on the display Pressing ENTER button and the display will show the number of working hours of the unit To go back to the functions press the MENU button again Press the MENU button up to when the ILU is blinking on the display Pressing ENTER button and all channels of the unit will return to their standard position To go back to the functions press the MENU button again 5 How To Control The Unit You can operate the unit in three ways 1 By master slave built in preprogram function 2 By easy controller 3 By IL 0824 pl
13. ion Latch LED off LED normal blinking LED on LED fast blinking IS 4 HID Stand Stand by Blackout the unit Function Strobe Gobo Color selection 1 Gobo Color sync strobe 1 Hold on for gobo change 2 Svnc strobe 2 Press shortly for color change 3 Two light strobe LED off LED on X Y moving pattern 5 3 1 iSolution Operation Consistent DMX configuration enable iRock and iShow to be linked together and controlled at the same time DMX address can be set remotely by iLead controller please refer to the user manual of iLead controller No need to calculate the DMX channels of each fixture in the chain Automatic switching between DMX function and built in stand alone programs 5 3 2 DMX Controller An universal DMX controller to control the units you have to set DMX address from 1 to 512 channel so that the units can receive DMX signal Press the MENU button up to when the ri is showing on the display Pressing ENTER button and the display will blink Use DOWN and UP button to change the DMX512 address Once the address has 11 11 been selected press and keep ENTER button pressed up to when the display stops blinking or storing automatically 8 seconds later To go back to the functions without any change press the MENU button again Please refer to the following diagram to address your DMX512 channel for the first 4 units DMX address can be set remotely by IL 0824 controller No
14. irrors must be carried out periodically to optimize light output Cleaning frequency depends on the environment in which the fixture operates damp smoky or particularly dirty surrounding can cause greater accumulation of dirt on the unit s optics e Clean with soft cloth using normal glass cleaning fluid e Always dry the parts carefully e Clean the external optics at least every 20 days Clean the internal optics at least every 30 60 days 17 17 EC Declaration of Conformity We declare that our products lighting equipments comply with the following specification and bears CE mark in accordance with the provision of the Electromagnetic Compatibility EMC Directive 89 336 EEC EN55014 2 1997 A1 2001 EN61000 4 2 1995 EN61000 4 3 2002 EN61000 4 4 1995 EN61000 4 5 1995 EN61000 4 6 1996 EN61000 4 11 1994 Harmonized Standard EN60598 1 2000 ALL 2000 A12 2002 Safety of household and similar electrical appliances Part 1 General requirements 18 18 Technical Specifications AC 120V 60Hz AC 230 240 250V 50 60Hz Fuse 20mm Glass T6 3A 20mm Glass T5A Lamp HID 150W 695 x 340 x 250 mm IR 5S 5B HID 685 x 380 x 200 mm IS 6S 6B HID 10 6 kg IR 5S 5B HID Weight 8kg IR 4C HID 9 4kg IS 6S 6B HID Innovation Quality Performance 19
15. it with a lint free cloth before installation 3 The lamp generates UV radiation Never operate the lamp without appropriate shielding N 4 When burning the lamp operates at high pressure and there is a slight risk of arc tube rupture The risk increases with age temperature and improper handling of the lamp Do not use the lamp anv longer than its specified life HID 150 Lamp installation or replacement e Always switch power off before installing or replacing the lamp Never try to replace the lamp when it is hot e Do not touch the bulb with bare hands Cleaning the lamp with denatured alcohol and wipe with a lint free cloth when lamp is dirty Red wire Loose the screw on the housing cover Loose the screws of the lamp wire from terminator Remove the old lamp from the fixture Please be care to install the lamp into case make sure it wedge tightly that it can not move easily WARNING impropriety install will cause the lamp lifespan shorten and maybe explosion during operation Connect the lamp wire to the terminator as before Please reinstall step 2 and step 1 se e E 4 How To Set The Unit 4 1 Control Panel DMX MIN MAX MIC ONLYFORREMOTE MASTER SENSITIVITY CONTROL CA 8 SLAVE SOUND OOO DJO MENU DOWN UP ENTER DMXIN DMX OUT Display To show the various menu and the selected functions LED MASTER Master Mode SLAVE Slave Mode Button MENU To seset e programing uneions
16. mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Dimmer Inversion Press the MENU button up to when the id is shown on the display Pressing ENTER button and the display will blink Use DOWN and UP button to select the 10 normal or dimmer inversion mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again L CO Led Display Press the MENU buiton up to when the LEO je showing on the display Pressing ENTER button and rr Mer the display will blink Use DOWN and UP button to select the Led on or DIr Led off mode Once the mode has been selected press the ENTER button to setup or automatically return to the main functions without any change after 8 seconds To go back to the functions without any change press the MENU button again Z ot Display Inversion It is good for you to install the unit on the floor or under ceiling Press the MENU button up to when the CO dE is blinking on the display Use the ENTER button to change to the mode COP i display inversion It will automat
17. need to calculate the DMX channels of each fixture in the chain Following DMX address setting is based on that all the lighting fixtures are linked together controlled by the 8 channel iLead IL 0824 controller IR 5S HID IR 5B HID IS 6S HID IS 6B HID IR 4C HID IS 4 HID 3L tL i ei 5 4 DMX512 Configuration mr IR 5S HID Barrel IR 5B HID Rotation IS 6S HID Barrel IS 6B HID Rotation Shutter Shaking Shutter IR 4C HID Shaking IS 4 HID Shutter Shaking Shutter Gobo Color Shaking No Dimmer Function Shutter Gobo Color Reflector Shaking Shutter Gobo Color Reflector Shaking Color Reflector m Gobo Color 12 12 5 5IR 5S 5B AC HID IR AC HID is a 4 channel color changer Ch2 Barrel Shutter Shaking 248 755 Open IR 5S 5B HID IR 4C HID 255 Fastest speed Gobo change 247 Fastest speed Shaking 4 120 127 4 111 119 103 110 132 Slowest speed shaking 135Slowest speed clockwise 094 102 086 093 131 Fastest speed shutter 121 134 Stopped 077 085 120 Slowest speed counterclockwise WM 069 076 r 060 068 052 059 4 043 051 16 Slowest speed shutter 035 042 026 034 1 Fastest speed counterclockwise 008 015 Open 018 025 008 017 000 007 Blackout 000 008 Stopped 000 008 i e TE Ch7 Color 255 Fatest speed Rainbow effect 255 Fastest speed Rainbow effect 128 Slowest speed Rainbow effect 121 127 Fink 118 127 Pink 113 120 Yell o
18. ulb enclosure or housing are damaged The housing the lenses or the ultraviolet filter must be replaced if they are visibly damaged Do not look directly at the light while the bulb is on Caution There are no user serviceable parts inside the unit Do not open the housing or attempt any repairs yourself In the unlikely event your unit may require service please contact your nearest dealer Installation The unit should be mounted via its screw holes on the bracket Always ensure that the unit is firmly fixed to avoid vibration and slipping while operating Always ensure that the structure to which you are attaching the unit is secure and is able to support a weight of 20 kgs for each unit 2 Technical Specification e Voltage AC 120V 60Hz or 230V 240V 250V 50 60Hz o Bulb HID 150W o The unit is DMX512 fixture It features full DMX512 control It can also be linked together in master slave connection as many as required in and run by built in program chase sequences automatically or by sound activation through an internal microphone to create an intelligent effect e t can be operated by DMX512 control or can be used as an individual unit without a controller o Consistent DMX channel enable iRock iShow and Move to be link together o Features different preprogrammed chase patterns e Please use a 3 pin XLR cable plug when connecting units together o Accurate focusable optics system and ultra smooth stepping motors Fan
19. w P ink 128 Slowest speed Rainbow effct 107 117 Yellow 106 112 Yellow 088 105 Orange Yalow 091 097 Orange 086 085 Light Green 083 090 Light Green Orange 076 087 Light Green 068 075 UV Purple 064 074 Blue 061 067 Blue 086 106 Orange 075 085 UV Purple 054 063 Red 053 0600 Red Blue 046 052 Red 038 045 Amber 032 042 Light Blue 031 037 Light Blue 043 053 Amber 022 031 Magenta 023 030 Magenta 016 022 Green Magenta 008 015 Green 000 010 White 000 007 White 011 021 Green 13 5 51S 6S 6B 4 HID IS 4 HID is a 4 channel gobo rotator DMX512 Configuration Chi Ch2 i Barrel Shutter Shaking 246 255 Stopped 248 255 Open 255 Fastest speed Gobo change Q 247 Fastest speed Shaking 128 Slowest speed Gobo change WM 120 127 111 118 O Q om 084 102 245 Fastest speed clockwise 132 Slowest speed shaking 135 Slowest speed clockwise 086 093 131 Fastest speed shutter 077 055 121 134 Stopped 069 076 120 Slowest speed counterclockwise 060 068 052 059 043 051 16 Slowest speed shutter 035 042 026 034 008 015 Open 018 025 010 Fastest speed counterclockwise 009 017 000 007 Blackout 000 008 Us Reflector 255 Fatest speed Rainbow effect 255 Fastest speed Rainbow effect 246 255 Stopped 245 Fastest speed clockwise 128 Slowest speed Rainbow effect Orv 121 127 Pink 118 127 Pink 113 120 Yellow Pink CA 107 117 Yellow 106 112 Yellow 128 Slowest speed Rainbow
Download Pdf Manuals
Related Search