INSTALLATION MANUAL
Contents
1. 2 If power waveform is deformed a trouble may occur 4 Safety Be sure to properly ground the machine Grounding earth connection must be performed before inserting the power plug into the power outlet When disconnecting the earth connection be sure to disconnect the power plug from the power outlet in advance 5 Power plug Check the shape of the power plug of the machine and insert it into a power outlet of the acceptable shape Power plug stated in power capacity D Floor strength and level This machine is considerably heavy and becomes heavier with an option installed The floor must be strong enough to safely support the weight of the machine as well as any installed options If the unit is not horizontally installed the toner density control is not performed normally degrading the copy quality If not color shift or image distortion may occur To assure proper Image quality make sure the machine is setting level E Direct rays of the sun dust temperature humidity gasses chemicals vibration 1 Temperature and humidity Environmental conditions This machine is designed to perform properly under the specified temperature and humidity If the temperature and humidity exceeds the specified range the machine may not operate properly and or cause equipment failure Especially when the humidity is too high paper absorbs humidity to cause a paper jam or2. 264NR M314NR M354NR MAIN UNIT 2 1 2 Installation NOTE When an optional paper feed desk is connected to the machine unpack and install the paper feed desk then unpack the machine Place the machine on the option desk securely and perform the installing procedures of the machine Place the machine on the optional desk firmly and secure A Developer installation NOTE Be careful not to leave fingerprints or oily dirt on the DV 1 2 3 4 5 roller surface Hold the both sides of the front cover and pull down to open it Rotate the MG roller in the arrow direction and supply devel oper evenly into the developing unit NOTE Shake the developer bag well before opening it NOTE Check that the DV seal is free from developer If devel oper is attached to the DV seal clean and remove it NOTE After supplying developer into the developer unit do not tilt or shake the developer unit Attach the developer unit to the copier and fix it with the screw Set the control level for the reference toner density 1 With the front cabinet open connect the power plug to the power outlet 2 Shake the toner cartridge horizontally 20 times 3 NOTE Do not forcibly insert the toner cartridge Push it in until the cartridge is securely locked in place 4 Turn ON the main power switch of the machine and the power switch on the operation panel 5 Enter the SIM2
3. 4NV M314NV M264NR M314NR M354NR MAIN UNIT 2 2 2 Tray size setup 1 Pull out the paper tray Gently pull the tray out until it stops If paper remains in the tray remove it 2 Adjust the guide plates A and B by squeezing their lock levers and sliding them to match the vertical and horizontal dimen sions of the paper to be loaded The guide plates A and B are slidable Slide each guide plate while squeezing its lock lever MX M264U MX M264U M314U M354U M264N M314N M354N M264NV M314NV M264NR M314NR M354NR MAIN UNIT 2 3
4. 5 2 mode 6 Close the front cabinet 7 Press EXECUTE key 8 After completion of the adjustment press reset key of the machine to exit the simulation mode C Paper feed tray setup 1 System setting 1 Press the SYSTEM SETTINGS key 2 Touch the Paper Tray Settings key 3 Touch the Paper Tray Settings key to configure the settings These settings specify the paper type paper size and func tions allowed for each paper tray When the Tray Settings key is touched a list appears showing the trays and the current settings 4 Touch the Change key in the above screen to change the set tings The following settings can be configured Item Description Type Select the type of paper that is loaded in the tray The paper types that can be selected vary by paper ray Size P the paper size from the list The paper sizes hat can be selected vary by tray The sizes that can be selected may also be restricted by the paper ype selected above If the desired size does not appear in the list select Custom Size and directly enter the size only for he bypass tray Feeding Approved Job function that you do not wish to be used with the Select the modes that can be used If there is a selected tray disable the function When the Type is other than plain paper recycled paper colored paper or a user type Fax and Internet Fax cannot be selected MX M264U MX M264U M314U M354U M264N M314N M354N M26
5. SHARP INSTALLATION MANUAL DIGITAL MULTIFUNCTIONAL SYSTEM MX M264U M264N M264NV M264NR MX M314U M314N M314NV M314NR MODEL MX M354U M354N 354NR Parts marked with A are important for maintaining the safety of the set Be sure to replace these parts with specified ones for maintaining the safety and performance of the set This document has been published to be used SHARP CO RPORATION for after sales service only The contents are subject to change without notice Transit Installation using environment Note About a main unit illustration it may differ from a target model 1 Installing use conditions Before installing the machine check that the following installing use conditions are satisfied If the installing use conditions are not satisfied the machine may not display full performances resulting in troubles It may also cause safety problems Therefore be sure to arrange the installing use conditions before setting up the machine No Content 1 Transportation space 2 Installing space 3 Power source Capacity fluctuation safety 4 Floor strength 5 Direct rays of the sun dust temperature humidity gases chemicals A Transportation space For installation of a large size machine be sure to check that the door size is wide enough before bringing in B Installing space The following space must be provided around the machine in order to assure mach
6. dirty copy Do not install the machine near a heater a cooler or a humidifier Condensation may form inside the machine causing multiple trou bles Use enough care for ventilation MX M264U Transit Installation using environment Note i F Note for handling PWB and electronic parts When handling the PWB and the electronic parts be sure to observe the following precautions in order to prevent against dam age by static electricity When in transit or storing put the parts in an anti static bag or an anti static case and do not touch them with bare hands Humidity RH 85 20 10 C 50F 30 C 86F 35 C 95F Operational environment Temperature 10 to 35 C Humidity 20 to 85 RH Atmospheric pressure 590 to 1013hPa altitude 0 to 2000 m 2 Contaminates If dust enters the machine it may cause dirty copy and a paper jam resulting in a shortened lifetime When and after removing the parts from an anti static bag case use an earth band as shown below e Put an earth band to your arm and connect it to the machine v 3 Direct sunlight ry If the machine is installed under the rays of the sun the exterior of the machine may be discolored and abnormal copies may be pro duced z p Nu 4 Gases and chemicals Do not install the machine at a place where there are gases and chemicals Especially be careful to avoid installation near a diazo Q type copier which prod
7. ine performances and proper operations If any option is installed provide the additional space for installing it Adequate space must be provide behind the machine for proper ventilation heat and dust If not the machine cannot exhibit func tions against heat and dust causing some troubles 11 13 16 30cm 11 13 16 lt x Lads gt 17 23 32 30cm 45cm C Power source Capacity voltage frequency safety plug If the power specifications are not satisfied the machine cannot exhibit full performances and may cause safety trouble Strictly observe the following specifications 1 Power capacity Check that the following power capacity is satisfied If not addition ally provide a power source Current capacity Japan 20A or more EX 100V 15A or more EX 200V 10A or more NOTE Check the shape of the power plug of the machine and insert it into a power outlet of the acceptable shape 2 Power voltage Measure the voltage during copying to check that the voltage is in the range of the specified voltage 10 If the voltage is outside the specified range please have a certified electrician upgrade the outlet An electrical work is required Use of a step up transformer is also available In this case the capacity must be great enough for the max power consumption of the machine 3 Power frequency waveform The frequency must be within the range of the specified frequency
8. thod 1 Implements facility Use a forklift If no forklift is available and man power manpower of two persons is required 2 Delivery Transit must be made in packed condition A Implements facility and manpower It is recommendable to use a forklift for bringing in the machine for safety If no forklift is available man power of two persons is required The machine is considerably heavy and requires safety precautions for delivery and installation Transit of the machine must be made in packed condition to the installing place Use care not to exert vibrations or shocks to the machine when in transit B Delivery Remove the packing materials prior to installation in the office envi ronment MX M264U Transit Installation using environment Note iii 2 MX M264U M314U M354U M264N M314N M354N M264NV M314NV M264NR M314NR M354NR MAIN UNIT 1 Unpacking C Packed items check A Unpacking No Name Quantity 1 Operation manual 1 D Lock release 1 Tray rotation plate lock release 1 Pull out the tray Turn the fixing material and remove it Remove the caution label Attach the removed fixing material to the position shown in the figure for future use Close the tray which was pulled out 2 Scanner 2 3 mirror unit lock release 1 Remove the optical unit fixing screw and remove the note label MX M264U MX M264U M314U M354U M264N M314N M354N M264NV M314NV M
9. uces ammonium gas Copy quality may be adversely affected and a trouble may be caused MG O P P fa e When repairing or replacing an electronic part perform the procedure on an anti static mat 5 Vibration Avoid installation near a machine which produces vibrations If vibrations are applied to the copier machine copy images may be deflected and a trouble may be caused MX M264U Transit Installation using environment Note ii G Note for proper drum developing and fusing unit handling When handling the OPC drum and developing units observe the following items Drum unit To prevent damage to the OPC drum avoid working on the drum unit in high intensity light areas e When the OPC drum is removed from the machine cover it with light blocking material When using paper use about 10 sheets of paper to cover it e Be careful not to attach fingerprints oil grease or other foreign material on the OPC drum surface Developing unit e Be careful not to leave fingerprints oil grease or other foreign material on the developing unit Fusing unit e Be careful not to leave fingerprints oil grease or other foreign material on the fusing roller If these items are neglected a trouble may be generated in the copy and print image quality 2 Transit and delivery No Content Me
Download Pdf Manuals
Related Search