Style 260C / Style 340C Laminator with Trimmer Operating Instructions
Contents
1. 3 Changing the cutting head y When the blades in the cutting head are damaged or worn the cutting head must be replaced Note Only the entire cutting head can be replaced 3 1 Remove the end cap of the guide rail from the base plate by pushing it upwards at the lower end at the same time as pushing it inwards gently 3 2 Replace the old cutting head with a new one 3 3 Slide the guide rail back in the device in the base plate and install the new cutting head in the process 3 4 Place the end cap from above on to the opening at the end of the guide rail Technical Data Style 260C Style 340C Maximum laminating width 230 mm 330 mm ror emanauer rel 80 and 100 mic 80 and 100 mic thicknesses Laminating speed 250 mm per minute 250 mm per minute Warm up phase 3 5 minutes 3 5 minutes iene atancantes LED POWER red LED POWER red LED READY green LED READY green ABS switch for clearing jams ABS switch for clearing jams Special features No blistering No blistering Automatic shutdown on overheating Automatic shutdown on overheating Trimmer Reel trimmers with 3 selectable types of cut Reel trimmers with 3 selectable types of cut and setting lock and setting lock Special features me ae l ane aor Visual positioning aids in cm Visual positioning aids in cm lines angles scale lines angles scale Straight cut Straight cut Selectable types of cut Wave cut Wave cut Perfo2. an easily accessible standard electrical socket Caution Check that the voltage specifications of the unit correspond to that of your power supply network 220 240V 50Hz 1 2 Use the on off switch on the right of the appliance to switch on HOT the red display lamp shows 1 3 The drive motor for the transport rollers starts up The correct operating temperature is reached after about 3 5 minutes and the green display lamp shows 1 4 Insert the document to be laminated in the pouches so that there is a margin of approx 3 5 mm to the edge of the foil on all sides Caution Only use foil intended for hot laminating 1 5 Insert the foil containing the document in the laminator s insertion slot Insert the ready closed side of the pouch first Note To prevent the laminating foil from creasing never insert the open end of the foil pocket in the insertion slot of the laminator first When inserting the foil observe the instructions on the insertion slot The laminating process occurs automatically Caution The lamination foil is very hot and soft when ejected following lamination Therefore handle the laminated document with due care Note To flatten and smoothen the laminated product place a book or similar heavy flat object on it 1 6 When you have completed the laminating process turn the function switch to the right in COLD position and remove the power plug from the power socket Let the device cool down before packing it
3. that it cannot slip when cut Otherwise the cut may be inaccurate 2 5 To complete the cut press the cutting head down and slide it along the guide rail to the other side refer to Fig 2 Note To prevent a faulty cutting edge do not run the cutting head back again but remove the cut material directly after completing the cut
4. transport rollers of any deposits and residual adhesive by inserting a folded piece of paper in the laminator infeed refer to Chapter Cleaning the transport rollers Note If foil jams occur repeatedly or jammed foil cannot be removed from the laminator please contact our hotline refer to Guarantee Trimmer The trimmer can be used to cut paper card photo paper and lamination foil 1 Selecting the type of cut The trimmer is equipped to complete three types of cut straight cut Llwave cut _lperforation cut Note The blades are accommodated in protective housing Select the type of cut you require see Fig 1 1 1 Pull the setting lock on the cutting head upwards to the OPEN position 1 2 Turn the rotating knob for the cut until the symbol related to the required cut is at the top 1 3 Press the setting lock on the cutting head downwards to the LOCK position Fig 1 similar to figure 2 Cutting material 2 1 Place the device on a stable level surface with the cutting head facing up 2 2 Slide the cutting head to one side of the guide rail 2 3 Slide the material to be cut under the transparent pressing rail at the required position Note Observe the permissible quantity of material which may be cut refer to Chapter Intended Use or Technical Data Note The visual positioning aids simplify correct alignment of the material to be cut 2 4 Hold the material to be cut firmly with one hand so
5. away for example Caution The device is very hot directly after laminating Risk of injury 2 Cold laminating Attention If you have just finished using the laminator for hot laminating you must let the laminator cool down It takes about 30 minutes to cool down sufficiently 2 1 Turn the function switch to the right in the COLD position Note Only use cold lamination foil for cold laminating 2 2 Remove the protective foil from the lamination foil 2 3 Insert the document to be laminated in the lamination foil so that there is a margin of approx 3 5 mm to the edge of the foil on all sides 2 4 Guide the laminating foil containing the document to be laminated in the laminator infeed with the closed side first The laminating process occurs automatically Note To prevent the lamination foil from creasing never feed the open side of the lamination foil first in the laminator infeed When inserting the lamination foil observe the instructions on the infeed slot 3 Clearing jammed lamination foil The device is equipped with an ABS switch anti blocking sliding switch to clear foil jams quickly Proceed as follows if the lamination foil jams 3 1 Switch the device off Set the On Off switch to OFF 3 2 Slide the ABS switch fully to the left 3 3 Hold the laminator firmly and pull the lamination foil together with the document to be laminated out of the laminator s infeed 3 4 Slide the ABS switch fully to the right 3 5 Clean the
6. ration cut Perforation cut Maximum size A4 A3 Straight cut 3 sheets of paper 80 g m Straight cut 3 sheets of paper 80 g m Maximum cutting capacity Wave cut 3 sheets of paper 80 g m Wave cut 3 sheets of paper 80 g m Perforation 3 sheets of paper 80 g m Perforation 3 sheets of paper 80 g m Dimensions W x D x H 385 x 135 x 100 mm 420 x 145 x 100 mm Weight 1 3 kg 1 8 kg Power supply 230 V 50 Hz 230 V 50 Hz Rated input power Max 265 W 1 1A Max 365 W 1 6A BIOSYS TEM Style 260C Style 340C Laminator with Trimmer Operating Instructions Operating Elements 1 Cutting head 2 Guide rail 3 Pressing rail with finger protection 4 Function switch temperature control i ners 5 Indicator elements LEDs HEF 4 N SE 6 Laminator infeed eee 7 Visual positioning aids in cm lines angles scale 8 ON OFF switch 9 Anti blocking slider for clearing jams 10 Corner rounder The function for rounding off the corners is located on the reverse side of the devices Operation Laminator The laminator can complete hot and cold lamination In the case of hot lamination the lamination foil is adhered together In the case of cold lamination the lamination foil is pressed together Select the lamination method according to the material to be laminated Note Only cold lamination should be used for thermopaper and ultrasonic images 1 Hot laminating 1 1 Connect the power cable to
Download Pdf Manuals
Related Search