Installation & operating instructions
Contents
1. cross head screwdriver Wire cutters THIS PRODUCT IS SUITABLE FOR WALL MOUNTING ONLY WIRING REQUIREMENTS The unit requires connection to a 230 AC 50Hz mains electricity supply It is recommended that the unit is connected to the domestic lighting circuit via a 5 amp fused spur and using 2 core round flexible cable of at least 1mm gauge waterproof cable should be used for outdoor installations It is also advisable to install a single pole wall switch to allow easy control of the floodlight Fig 1 INSTALLATION INSTRUCTIONS CHOOSING A MOUNTING LOCATION e Mount the floodlight onto solid brick or woodwork 3 5m above the ground Fig 2 e Avoid positioning the light near heat sources such as hot ventilator ducts air conditioning units street lighting or traffic which may interfere with its operation FIXING THE CONNECTION BOX WARNING Isolate the power supply before installation e Position the unit on the wall and mark the position for the connection box which can be positioned in either landscape or portrait planes Fig 3 e Ensure the wires can easily enter the connection box through either one of the knock outs on the side of the connection box or through the knock out at the rear of the box NOTE It is recommended that the knock outs on the sides of the connection box are used in conjunction with the cable gland Fig 4 as using the knock out at the rear of the connection box will reduce the weatherproof rat2. into the lighting circuit Use a switched fused spur Cables should always be protected against short circuit and overload by use of an RCD A Ensure the voltage marked on the product is the same as the electrical power supply to be used A DO NOT install the light where it is likely to be knocked or hit in hot or humid conditions such as bathrooms shower rooms or saunas or near an exhaust outlet e g boiler flue dryer outlet IMPORTANT OPERATION amp MAINTENANCE INSTRUCTIONS DO NOT position the light near flammable or combustible materials Such as wood cloth paper or near flammable combustible or explosive liquids solids gases or equipment DO NOT direct the light into a person s eyes This light has a very intensive light output which if incorrectly used could cause eye damage A ALWAYS disconnect the mains power supply before servicing or performing any maintenance A ALWAYS maintain the light in good condition with repairs only undertaken by a qualified electrician A ONLY carry out repairs using genuine parts Non authorized parts may be dangerous and will invalidate the warranty PARTS INCLUDED TOOLS REQUIRED 1 x Mightylite LED Floodlight 1 x Connection box 1 x Cable gland 4 x Connection box screws 4 x Connection box screw covers 4 x Connection box fixing screws 4 x Connection box fixing screw covers Electric hand held drill No 8 masonry drill bit Electricians screwdriver Large cross head screwdriver Small
3. FIXING THE CONNECTION BOX Cont e Use the connection box Fixing Holes Fig 6 to mark the 4 drill holes required to secure the box to the wall and mark the cable outlet location if required Drill the wall and screw the connection box onto the wall using the screws and wall plugs provided MIGHTYLITE Fixing Holes e Once the wire s has been fed through the Sealing Gland the nut on the gland a should be gently tightened up against the gland body Fig 8 to ensure the i i i wire s is secured in place and no water can get though into the connection box lc E epi Floodlights oOqQel WIRING THE FLOODLIGHT e Once the power cable has been fed through the cable gland or sealing grommet if using the knock out at the rear of the connection box aie approximately 6mm of insulation should be stripped from each of the cores of B AC cable ready to attach it to the terminal block in the front of the light fitting m NOTE The Hylite Mightylites MLF016 and MLF028 are Class 1 fittings and therefore need to be Earthed CONNECTING TO POWER SUPPLY e Connect the BROWN or RED Live wire to the terminal marked L holding the single BROWN wire in the floodlight unit Fig 8 e Connect the BLUE or BLACK Neutral wire to the terminal marked N holding the BLUE wire in the floodlight unit e Connect the YELLOW GREEN or BARE Earth wire to the terminal marked EARTH holding the YELLOW GREEN wire in
4. ing of the unit to IP23 e However If feeding a wire s through the knock out at the rear of the connection box this will need to be removed the sealing grommet fitted Fig 5 and the wire pushed through into the connection box BEFORE it is secured to the wall e f feeding a wire s through the side knock outs it is easiest to fit the cable gland to the connection box Fig 4 BEFORE securing it to the wall and wires should enter the connection box from the sides or underneath NOT from the top TO MAINS i Y Portrait bal we MIGHTYLITE Landscape Fig 4
5. the floodlight unit e After the connections have been secured the floodlight front Connection Box front should be fastened to the Connection Box using the 4 Connection Box Screws provided Fig 9 Se ee EEEE e Once screws are secure the screw covers provided should be fitted should be fitted Fig 9 e To adjust the MightyLite simply hold the Connection Box firmly whilst moving the head of the floodlight to the required position F4 Enterprises Limited Tel 44 0 1352 736120 7 Abbey Square Chester www f4enterprises co uk C CH1 2HU UK Installation amp operating instructions HYLITE MIGHTYLITE INSTALLATION AND OPERATING INSTRUCTIONS The Hylite Mightylite floodlight a low energy high powered outdoor LED floodlight which is suitable for installation on solid walls in a range of locations including entrances gardens staircases garages and outdoor parking areas The unit requires connection to a 230 AC 50Hz mains electricity supply IMPORTANT SAFETY INSTRUCTIONS WARNING THIS PRODUCT MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN AND CHECKED TO ENSURE IT IS SAFE BEFORE USING PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY BEFORE ATTEMPTING TO INSTALL AND OPERATE THIS LIGHT A The risk of electric shock should be minimized by the installation of appropriate safety devices including the incorporation of an RCCB Residual Current Circuit Breaker into the main distribution board A DO NOT wire this floodlight directly
Download Pdf Manuals
Related Search