Automatic Swing Door Operator DFA 127 Operating instructions E
Contents
1. PETIT TTT UL 13 12 14 11 10 9 8 16 Key to illustration 1 Mains connection terminals 9 Slide switch S1 rotating direction 2 Fine wire fuse 10 Multifunctional switch MF on STG 3 Power supply NET 11 Closing spring 4 Drive unit ATM 12 Vision panel adjust spring tension 5 Control unit STG 13 Adjusting screw for spring tension 6 Connection terminals control unit 14 Connectors for arms both sides 7 Motor print MOT 15 Standard switch BDI 8 ATE drive unit terminals 16 Status signal and Reset button Do not change any settings or adjustments These operations are re served exclusively for trained and authorized persons 4 2 Components The record DFA 127 swing door operator forms part of an electromechanical swing door system and comprises the following main components Control unit STG Intelligent learning microprocessor controlled control system Driving unit ATE Low maintenance DC geared motor with electronic path measurement and integral thermostatic protective switch gear box with adjustable spring tension Power supply NET Compact 230 V power supply with integral input filter and over voltage protection Control unit BDE As required with convenient simple mechanical control unit and or a programmable electronic BDE D Operating instructions DFA 127 Full Power Rev B 11 2006 Page 5 of 20 ME Construction and Function Arm types Power transmis2. Reset automatically Status 59 SIS sensor active longer than 60 s Automatically reset if in order or by service fitter Page 18 of 20 Rev B 11 2006 Operating instructions DFA 127 Full Power Me Status and fault signals Status 60 Status 61 Status 62 Status 72 Status 88 Status 89 Status 90 Status 91 Status 92 Status 93 Status 94 Status 95 Status 96 Status 99 Status 105 Parameter memory EEPROM defective Change control unit Reset by service fitter SSK active longer than 60 s Automatically reset if in order or by service fitter BDE has no priority Because a higher level signal is present Automatically reset on release of BDE button Slave connection Master has no connection to Slave operator Reset by service fitter Difference parameter The common parameters of M S operators do not correspond to each other Reset by service fitter Master connection Slave has no connection to master operator Reset by service fitter Railbeam active gt 60 sec Automatically reset if everything Is in order or by service fitter Bodyguard active gt 60 sec Automatically reset if everything is in order or by service fitter STG relay defective Replacement by service fitter Overvoltage 24 V from 27V Spring calibration Automatic reset Error in sense of rotation EEPROM void Operator rotates The grease in the gear will be dispersed Automatic reset Test brake Automa
3. CYCLE Factory default Parameter Factory default Closing speed 10 Opening speed Operating instructions DFA 127 Full Power Rev B 11 2006 20 Page 13 of 20 7 Maintenance instructions 7 1 General The record DFA 127 swing door operator is a product of the latest technology It has been carefully made and only leaves the factory following thorough testing Automatic swing doors should be operated and maintained to ensure safety at all times 7 2 Care The entire swing door system can be cleaned with a damp cloth and commercially available cleaning agents The cleaning agent must be harmonised to the surface which has to be cleaned lt is recommended to select the Continuously open or Locked mode of operation for this purpose so that the door does not continually open and close unnecessar ily 7 3 Maintenance periodic inspection lt is recommended to have a technical safety test with servicing performed by a specialist before first commissioning and as required but at least twice a year Regular testing and servicing by our fully trained personnel therefore offers the best guarantee for a long service life and satisfactory operation We therefore recom mend the signing of a maintenance agreement Our service department will be pleased to submit a proposal lf nevertheless a fault should occur which you cannot eliminate See section 8 our service organisation or the maintenance personnel of ou
4. Page 16 of 20 Rev B 11 2006 Operating instructions DFA 127 Full Power Me Status and fault signals 8 3 Detail description of status indications General A status can usually be deleted by pressing the key for 5 s Reset This produces a new start in the control unit If however the cause of the fault has not been eliminated the status message will appear again if the fault occurs again The following list contains the causes of faults in decreasing possibility The fault at the bottom of the list has the smallest probability to occur in the control unit STG Status 3 AKI sensor active longer than 60 s Automatically reset if everything is in order or by service fitter Status 5 AKA sensor active longer than 60 s Automatically reset if everything is in order or by service fitter Status 6 Unlocking error Bolt possibly jammed Reset by service fitter Status 9 Opening unsuccessful after 4 collisions Check the interlock remove obstacle Reset through service fitter Status 11 Faulty motor current Possibly faulty wiring in prefabricated cables Replacement by service fitter Status 23 Slave control unit defective Replacement by service fitter Status 25 Slave connection CAN to Master interrupted Clear by service fitter Status 31 EMERGENCY STOP operated Motor relay de energises Reset by resetting the EMERGENCY STOP button Status 37 Motor current STG or ATE defective Reset by service fitter Stat
5. Automatic Swing Door Operator DFA 127 Operating instructions E LOM A Page hs 4 General 2 2 Safety instructions 3 3 Technical data and operating conditions 4 4 Construction and function 5 6 5 Operating instructions 7 11 6 Configurations 12 13 7 Maintenance instructions 14 8 Action in case of faults 15 20 agtatec ltd Allmendstrasse 24 X CH 8320 Fehraltorf Phone 41 0 44 954 91 91 Fax 241 0 44 984 92 00 record Date 11 2006 BU article no 127 109 265 B 1 General These operating instructions are intended for the record DFA 127 FP EU or record DFA 127 FP GG EU automatic swing door operator herein after referred to as DFA 127 The operator is the person responsible for the technical maintenance of this door system These instructions describe the use of the record DFA 127 swing door operator They form the basis for satisfactory functioning These operating instructions should be read by the door operator before commis sioning and the safety instructions observed It is recommended to keep these operating instructions close to the automatic slid ing door Product designation Automatic swing door operator Product name record DFA 127 FP EU or record DFA 127 FP GG EU Serial number Page 2 of 20 Rev 11 2006 Operating instructions DFA 127 Full Power PE Safety instructions The record DFA 127 swing door operator has been constructed in accordance with the latest state of the art and
6. an 4 po atitomatic S 5 The BDE D indicates the current operating mode lf an operating mode is set on the BDE D which has no current priority the status message 62 is displayed Reset button After pushing for approx 5 sec a new start of the control is performed software reset After the reset the LED lights up permanently Status signal Remains off if no fault is present Will blink if a fault is present See status and fault signals chapter 8 Does light up permanently during a reset Page 8 of 20 Rev B 11 2006 Operating instructions DFA 127 Full Power Ml Operating instructions 5 2 Auxiliary controls on the control unit STG 127 General The CONTROL UNIT STG 127 operates with active HIGH level i e a 24 V level must be applied to activate a function Safety inputs are activated during interrup tions The signal ground OV is connected to protective earth Jumpers J14 Master Slave jumper at position M1 for master factory setting jumper at position S1 for slave J13 CAN line termination LED s LD1 red control LED for push button operation S1 LD2 green 35V Off for power failure LD3 green 24V Lights if 24V present Caution in the event of a power failure processor reset takes place 1 second after this LED extinguishes Push button S1 This is a multifunctional switch on controller MF The use of this switch is reserved exclusively for trained and authorized pe
7. eration ey The door can be opened and closed by hand Open continuously 1 gt The door is opened and stays open Locked B In the operation mode Locked the locking is activated Table to signals X marks a release reaction Reset After pushing on the button for approx 5sec this status message on the display is Reset Operator Pushing again on the button resets the operator Operating instructions DFA 127 Full Power Rev B 11 2006 Page 11 of 20 6 1 Please always leave the parameter overview sheet in the operator even when the record parameter overview sheet DFA 127 swfromw130 oto js replaced Value will reset after default parameter loading All parameter modifications must be marked as follows in the relevant box Slave 1 or Slave 2 Speedo programmed value parameter only with multifunctional button on control unit technical level parameter value X mark Parameter value factory settings printed bold D S1 Description M8 dae aS e DRIVING CYCLE Closing speed Opening speed peedo Speedo Speedo Different accelerations Speedo Star latch check by closing oO oO oO D yf o fm 3 Latch check TIME DELAY OPEN Time delay open Time delay SSK DRIVE Opening angle Collision Brake Types of arms nvers Spring type Limit open ENTRANCE SYSTEM Fire alarm Control Interlock type x Le PERH x Sp oO Closing position Sliding pullling E Z ra Enabled vi peni
8. h the 3 position toggle switch on the side cover Manual operation a In this operation mode the DFA works as a normal door closer It can easily be Opened manually and then closes automatically The connected actuating ele ments are inactivated Automatic a The door opens and closes automatically either by activation of an actuating ele ment or by pushing with activated touch control Continuously open lt gt The door opens and remains in the open position If an obstacle is encountered while opening the DFA will attempt during the next few seconds to get the door into the set open position If the obstacle is still present the current position will be accepted as the continuously open position Operating instructions DFA 127 Full Power Rev B 11 2006 Page 7 of 20 Ml Operating instructions The mechanical BDI is by factory default always connected and active on a DFA 127 lf an additional electronic BDE D is connected the operating mode is set by a defined priority structure from the BDE with the highest priority The priority and the code shown in the following table apply to the operating mode whereby BDE2 S2 and BDE1 S1 represent the two input terminals of the control unit J7 1 J7 2 p c b BDE M for the mechanical BDE L interruption or OV H 24V Mechanical BDI toggle switch Electronic BDE D BDE2 S2 BDE1 S1 Priority 1 highest Coo rrr po omneway po continuouslyopen _ 3 pA m
9. ing the operation in order to avoid injury or damage No objects must be placed in the opening zone path of the swing door to avoid crushing and shearing points The safeguard for crushing and shearing strains at the side edge must be provided by the manufacturer Operating instructions DFA 127 Full Power Rev B 11 2006 Page 3 of 20 3 Technical Data Dimensions Operator 600 x 85 x 124 mm wxh xd Operating voltage 230V Power consumption Standby 13 W rated power 67 W Max torque 50 Nm Opening angle Adjustable from 70 to 115 Time delay Adjustable from 0 to 20 seconds Opening speed Adjustable from 3 to 20 seconds Closing speed Adjustable from 5 to 20 seconds Noise emission 18 dB Environment conditions Temperature range 15 to 50 C Humidity range Up to 85 relative humidity non bedewing 3 1 Permissible door leaf weights and door widths BOO Standard and sliding arm A O AME Max door leaf weight kg 0 6 07 08 0 9 1 0 1 1 1 2 se 14 Door leaf width m The curves are calculated using to the following formula J 1 3 xm xb Standard arms Jmax 65kgm Key J mass moment of inertia kgm Slide arms J max 65 kgm m door leaf weight kg b door leaf width m Page 4 of 20 Rev B 11 2006 Operating instructions DFA 127 Full Power 4 Construction and Function 4 1 Construction A y 1 ETON LA ae 1 1
10. ng position liding pushing Open Clos pos Inheader oo Standard arm azaz Taran ena Era Era E E ie Master control E Slave control Master Slave it Master Master x CENTRE it mn ERRE iii ill x ingle control ithout inter single leaf inter double leaves lock control interlock control USA USA Low Energy m mn Basic operator EU Low Energy E c ne gt ad a es oe ce Door type MS 2 LEAVES Function AKA Overlap Open sequence Close sequence MANUAL CONTROL During closing PB Masterssiave E Masteronly W te ee te Speedo O No overlap Speedo 0 Simultaneous opening Speedo 0 Simultaneous closing Eudes zzz i D gt o oO D a 3 ollision upport during closing J ctive sensors losing speed CONTROL PANEL Mech panel O ZEL EHRE P x 3 Pos AUTO 4 Positions 3 Pos OFF A 3 Pos Lock A 3 Pos Lack M Manual Automatic Automatic Automate Manual Automatic Manual OFF Locked Locked Cont open Cont open Cont open Cont open psj BDE D submenu Ey Language Keyboard Contrast BDE 1 Contrast BDE 2 Light time LOCKING a Locking function Lock type aa Normally locked Always locked Standard Locking bot Enabled Speedo lt a D 3 oa ow z z z z Start delay INPUT x AUX1_IN x aan TM OUTPUT oeae a a a a a x auxi out m Di
11. r agents are available 7 4 Service centres In Switzerland Phone 41 0 44 954 92 92 Fax 41 0 44 954 92 00 Alternative service centre Page 14 of 20 Rev B 11 2006 Operating instructions DFA 127 Full Power E S Action in case of faults 8 1 Fault indication Various indications are given for an irregularity or fault depending on the control unit connected BDE E or BDE M When using a mechanical BDE control toggle switch With the mechanical control unit it is not possible to display a detailed status sig nal If a fault occurs will be shown by the status signal on the side cover please proceed according to section 8 2 When using an electronic BDE D General Any current operational faults in the drive system will be displayed in the Standard screen If several faults are active they will be numbered e g Fault 1 2 In case of an irregularity the display changes automatically from mode of operation level to error display Every 2 seconds the backlight changes between normal invers Several errors can be displayed e g 1 2 means error no 1 of total 2 er rors After 10 seconds the telephone number of the responsible service centre is indi cated alternating to the fault indication The failure indication and the phone num ber change every 5 seconds while the inverse flashing is remaining The de scribed sequence applies to all failures However previously the phone number must have been given by an authorised
12. rsons Top view of the control unit STG STG DFA 127 C agtatec ag CH 8320 Fehraltorf record oH E J12 z l o gt EA Lg ENCODER gt 7 7 H T T 7 18 lI 19 2021 22 2324 1 2 23 24 Panes chal pes mm a b MOTOR BOARD 07 Controll LED D2 Operating instructions DFA 127 Full Power Rev B 11 2006 Page 9 of 20 Ml Operating instructions 5 3 Functions of electronic controller BDE D optional The electronic controller BDE D is an easily op erated input and output device for the control and adjustment of record door operators Logically arranged push buttons allow an intuitive operation and navigation through the operator specific menu The LCD with backlight shows data and information about the door status with symbols and text messages Additional information can be taken from the manual of the BDE D No 903 109 271 record 5 4 Operation modes Automatic Normal function Table to signals X marks a release reaction a CLOSED OPENING OPEN CLOSING One way traffic In one way traffic mode people cannot enter the room from the outside but they can leave it from the inside Table to signals X marks a release reaction CLOSED OPENING OPEN CLOSING AKI awo oo oo o S SSK fx o b o SO fe sis l o O O AKA is active as safety device while closing Page 10 of 20 Rev B 11 2006 Operating instructions DFA 127 Full Power E Operating instructions Manual op
13. rvice fitter oo Control unit SLAVE defective o MASTER SLAVE connection interrupted Reset by service fitter Release EMERGENCY 31 Doorstops EMERGENCY STOP button operated STOP button 38 Door changes to manual cess iemperaiieanoior Wait until motor has control cooled 390 EUnet eve AKE Overload on 24 V supply Reset by service fitter too much power 44 Doorstops Motor 1 thermal sensor defective Reset by service fitter 43 Doorstops Incremental transmitter defective Reset by service fitter Minimum hold open time Motor current time product too large Wait until motor has increased to 20 secs cooled 46 Doorstops Control unit defective Reset by service fitter Remove obstacle from Door remains closed SIO sensor longer activ than 60 sec surveillance range of sensor Control unit defective Reset by service fitter CY No valid drive parameter Initiate calibration run 53 Doorstops Interruption motor Reset by service fitter Door jolts possibly while Calibration run Initiate 1 opening cycle opening Remove obstacle from Door stops SIS sensor longer activ than 60 sec surveillance range of sensor 60 Doorstops Parameter memory defective Reset by service fitter 61 Doorremains open ey operated contact active longer than 60 Release eu cont Higher order mode of Canivolubit BDE has napnoiiy Cancel higher order operation present mode of operation 03 05 3 5 1 T 8 9 1 3 s 6 7 90 52 53 54 99 61 O O gt ep
14. sabled EBEA Bodyguard Ej Test closed f Testopen W MO MISCELLANEOUS fe ee ee eee Pe De Push to actuate m Disabled Normal motored P Siow roto rEwinsensos Sid O i m Order number Client IE This parameter overview shows all possible settings Depending on drive type and configuration the access is restricted Page 12 of 20 Rev B 11 2006 Operating instructions DFA 127 Full Power EE Configurations Configurations of the DFA 127 can only be made with the electronic BDE D If a toggle switch is connected a BDE D must be connected briefly for the configura tion Further information for parameter changes can be taken from the user manual of the BDE D no 903 109 271 Please always leave the configuration review sheet in the drive 6 2 Parameter description Parameter Setting Factory Description range default DRIVING CYCLE fe Closing speed 0 40 Slider control with 40 steps 5 20 s Opening speed 0 40 Slider control with 40 steps 3 20 s TIME DELAY OPEN Time delay open 0 40 2 0 60 s actuate 0 20 Stepsofis Effective with AKA AKI and push to 21 40 Steps of 2s Time delay SSK 0 40 4 0 60 s 0 20 Steps of 1 s 21 40 Steps of 2s Effective with SSK DRIVE o d _ The opening angle is estimated dur ing the calibration run and is equiva lent to the value of 40 6 3 Different factory defaults for door types Low Energy Parameter DRIVING
15. sion to the door leaf by use of standard arm pushing or sliding arm pulling pushing Locking VRR optional It is possible to connect an electrical door opener 24VDC to the operator Sensing units Aesthetic actuating and self monitoring safety elements with adjustable sensitivity ensure optimum smooth and reliable operation of the door system 4 3 Functional description In the standard Automatic mode of operation the door system opens by the re sponse of an actuating device e g radar unit to persons or objects approaching The door closes after the door hold open time provided no further opening pulse is received In the Lock mode of operation the door is only opened by actuation of an op tional key operated contact SSK The door closes after the SSK door hold open time provided no further opening pulse is received An obstacle to the swing door leave during Closing leads to an immediate re opening reverse The obstacle position is recorded in the door operator and this position is approached slowly when next closing An obstacle to the swing door leaf when Opening results in an immediate stop Page 6 of 20 Rev B 11 2006 Operating instructions DFA 127 Full Power HEB Operating instructions 5 1 Mech control elements and indication 1 Mechanic BDI with 3 positions control toggle switch 2 Reset button 3 Status signal Mechanical BDI control toggle switch The following operational modes can be set up wit
16. specialised person Information about the drive system such as the software version can be read out by pressing the key After pressing this key once again the phone number of the responsible service centre and the last appeared fault indication is displayed in the screen If the fault message consists of several lines the first line will be displayed only Status signals with a W are warnings For these the fault relay contact output is not connected Elimination of the irregularity leading to the status signal is per formed according to section 8 2 A status can usually be deleted by pressing the key for 5 s Reset This pro duces a new start in the control unit lf however the cause of the fault has not been eliminated the status message will appear again if the fault occurs again Operating instructions DFA 127 Full Power Rev B 11 2006 Page 15 of 20 E Action in case of faults 8 2 Error elimination The majority of faults can be eliminated by consulting the following table If the fault cannot be eliminated even after working through the table please contact the service centre Please also contact the service centre directly when no recom mended action is specified in the table symptom fault Cause Action door behaviour consult service if no recommend action 2 2 3 3 3 3 4 4 4 4 4 Actuating device inside active longer than Actuating device outside active longer than oT micas Utne CO Reset by se
17. the recognised technical safety regulations including limiting of forces and speeds Nevertheless danger can arise for the user if not used as intended Installation maintenance and repairs to the record DFA 127 must only be performed by qualified and authorized personnel technicians 2 1 Use as intended The DFA 127 swing door operator is constructed exclusively for normal service with swing doors in dry rooms and must be installed within or inside buildings A different application or use extending beyond this purpose is not considered use for the intended purpose The manufacturer declines all responsibility for resulting damage the operator alone shall bear the associated risk Use for the intended purpose also includes observation of the operating conditions specified by the manufacturer including use and adjustment of the correct type of arms in addition to regular maintenance and repair Unauthorised modifications to the automatic door operator exclude any liability of the manufacturer for resulting damage 2 2 General safety and accident prevention regulations In general no safety devices Sensors may be dismantled or put out of service During the learning cycle which must only be performed by trained per sonnel the safety devices Sensors are switched off It must be en sured therefore before initiating the learning cycle that no persons or objects are situated in the danger zone of the moving door leaves dur
18. tic reset Operating instructions DFA 127 Full Power Rev B 11 2006 Page 19 of 20 Me Status and fault signals Status 106 Status 107 Status 108 Status 109 Status 110 Brake defective Reset or reset by service fitter SIS defective A safety sensor with test input in closing direction is defective Reset by service fitter SIO defective A safety sensor with test input in opening direction is defective Reset by service fitter Factory settings No motor No motor detection during initialisation motor temperature sensor Check motor temperature sensor Reset or reset by service fitter I A status number with a W is a warning Page 20 of 20 Rev B 11 2006 Operating instructions DFA 127 Full Power
19. us 38 Overheat motor Manual control effective Door leaves possibly too heavy or too much friction Reset by motor cooling down or by service fitter Operating instructions DFA 127 Full Power Rev B 11 2006 Page 17 of 20 Me Status and fault signals Status 39 Overload on 24 V supply Too many external units possibly connected Reset by service fitter Status 41 Motor temperature sensor defective Motor possibly not connected Sensor in motor possibly defective or cable break in sensor lead Reset by service fitter Status 43 Incremental encoder fault Input cable possibly not connected or cable break in the lead Motor possibly blocked Reset by service fitter Status 45 Motor current time product to high Motor relay de energises Manual control effective Automatic reset by motor cooling or by service fitter Status 46 Control unit STG defective Includes the following individual faults EPROM RAM Watchdog Imax ImaxT difference on SHE EXT Reset by service fitter Status 47 SIO sensor active longer than 60s Automatically reset if in order or by service fitter Status 50 CPUZ2 is defective Reset by service fitter Status 51 Software version Software version of Master and Slave do not correspond to each other Software update by service fitter Status 52 No running parameter Start calibration run Status 53 Interruption motor Possibly no connection to motor Reset by service fitter Status 54 Calibration run
Download Pdf Manuals
Related Search