Enabled Wireless Installation Manual
Contents
1. inovonics 2 5 GJD1050R D TECT Inovonics Enabled Wireless Installation Manual The D TECT Inovonics MUST be learnt to the control panel receiver BEFORE it is mounted in its final location Please see page 4 of this manual and the Inovonics Manual for details 1 Batteries Page 1 of 4 2013 GJD Manufacturing Limited October 2013 Rev 1 All rights reserved Page 2 of 4 October 2013 Rev 1 Packaging The package contains e 1x wireless detector e 3x wall plug amp screw sets 1x tamper cup e 2x tamper caps different lengths e 1x plastic opening tool e 1x installation manual e 1x drilling template for fixing holes GJD s Inovonics enabled D TECT The wireless detector uses a quad pyro where both sensors must trigger to cause the detector to signal an alarm ensuring precise and reliable presence detection Programmable options include a variable pulse count and a choice of detection ranges up to 50 meters The dual axis tilt sensor allows 180 of pan and 90 of tilt This increases the speed of the outdoor installation and provides accurate aiming of the detection pattern Precision electronics digital white light filtering and double shielding eliminates false alarms from the sun The detector housing has a professional appearance with the sensing module hidden behind the front cover Quick installation 1 Place two CR123 batteries into the detector batte2. sensors are more sensitive to movement across the beams and less sensitive to movement directly towards or away Figures 5 amp 6 show typical beam patterns Programming Figure 7 shows the position of the programming button 2 and the programming LED 1 October 2013 Rev 1 Table 1 Programming settings Option 1 2 3 1 Range m 10 25 50 2 Pulse count 1 2 Default settings Pulse count is the number of detections before signalling an alarm Pulse count 1 is most sensitive Changing settings 1 Press the programming button once for range and twice for pulse count 2 Wait until the programming LED turns off typically 4 seconds 3 Count the number of times the LED flashes to determine the current value for that option 4 Press the programming button to select the value number for the new setting E g to change the range to 25m press twice The LED blinks twice to indicate that the new value was set Programme settings are stored in non volatile memory Resets 1 Remove the batteries 2 Press and hold the programming button See Figure 7 item 2 3 Refit the batteries 4 After the programming LED has flashed release the programming button Learning to control panels receivers When the control panel receiver is in learn mode press the detector programme button once After about 10 seconds the wireless detector will be learnt on to the control panel Walk test In walk test mode
3. the detection LED option is set to ON and the detection LED will illuminate on detection To enter the walk test mode press the programming button once The unit can now be aligned Walk test mode ends automatically five minutes after the last detection Do not conduct walk tests with the cover removed The range of the detector increases without the protective front cover Therefore the front cover must be fitted to establish the correct beam pattern Adjust the range as necessary Pan and tilt the detector module over the field of view to obtain the correct coverage Specifications Detection range Programmable 10 25 or 50m Coverage 50 x 10m 13 detection angle Page 4 of 4 Adjustment 180 pan 90 tilt Optics Double silicon shielded quad element eliminates 50 000 Lux of white light LED Red alarm Batteries 2x 3 V CR123 Current 30 WA Pulse count 1 or 2 Control Digital micro with non volatile memory Walk test Output test mode with LED indication Operating temperature Housing Dimensions W x H x D Weight Mounting height Compliance Manufacturer 25 to 65 C High impact ABS plastic with HDPE cover UV stabilised 145 x 145 x 120mm 268g Net 425g Gross Variable up to 4 meters Optimum 3 meters GJD Manufacturing Limited Unit 2 Birch Business Park Whittle Lane Heywood Lancashire OL10 2SX UK Certification C E R amp TTE This device is in compliance with the essential require
4. he tamper cup on uneven surfaces e The optimum mounting height is 3m Higher mounting heights will result in reduced detection range and the target will have to move a greater distance within the field of view before an alarm is generated 2 Remove the cover assembly using the plastic opening tool and by loosening the locking screw See Figure 2 3 Screw the unit to the wall Ensure the tamper pin is correctly located and the tamper switch is closed Two different length tamper feet are provided for uneven surfaces The tamper foot is a push fit see Figure 1 4 When the detector is aligned powered and programmed a Fit the cover b Loosely tighten the locking screw c Push the two side plastic latches into the base d Tighten the locking screw Batteries Only use CR123 3 V Lithium batteries Observe correct polarity when fitting Battery safety information e Do not put ina fire e Do not charge e Do not heat e Do not short circuit e Do not disassemble e Only fit batteries of the same type and voltage To preserve battery life the detector has a 2 miniute sleep timer after detection This is reduced to 8 seconds during walk test See also Walk test section on page 4 Beam alignment and masking The PIR circuitry detects changes in heat and movement in the beam pattern The presence of trees shrubs ponds boiler flues black tarmac and animals should be considered when positioning the detector PIR
5. ments and other relevant provisions of Directive 1999 5 EC Environmental IP65 class 2002 96 EC WEEE directive Products marked with this symbol cannot be disposed of as unsorted municipal waste in the European Union For proper recycling return this product to your local supplier upon the purchase of equivalent new equipment or a ee oa dispose of it at designated collection points For more information see www recyclethis info Contact information Web www gjd co uk Tel 44 0 1706 363 998 Email sales gjd co uk October 2013 Rev 1
6. ry holders Observe the polarity See figure 4 item 1 The detection LED will flash 3 times 2 Enter the learning menu on the control panel receiver To learn the device follow the instruction given in the Inovonics documentation 3 Press and release the programming button once to learn the device Fig 10 item 2 This action also activates walk test mode Note The learn process may take up to 10 seconds from pressing the programming button Learn will be confirmed on the control panel receiver 4 The detector will take approximately 3 minutes to settle The detection LED is now enabled for five minutes 5 Mount the detector following the instructions below The default settings are e Range 50 meters e Pulse count 1 Fitting the detector Protect the electronics against water Trapped moisture can affect or damage the unit Mounting holes should be sealed from within the detector using acrylic non silicone based sealants Silicone sealants must not be used as vapours may corrode the electronics and metal parts Note The Inovonics transmitter is supplied with the ES link disabled If this is required then the transmitter module will need to be removed to enable the link then replaced Ensure the detector s field of view is unobstructed Mounting the detector 1 Drill the wall to accept the fixing screws and the tamper cup if used See Figures 1 and 3 A hole drilling template is provided Notes e Use t
Download Pdf Manuals
Related Search