FlushlightLED installation manual
Contents
1. 4 7000 Channel Safety Systems Limited F 0845 884 6000 Petersfield Business Park C 1 L E sales channelsafety co uk Bedford Road Petersfield SAFETY SYSTEMS W www channelsafety co uk Hampshire GU32 3QA INSTALLATION 1 Remove the diffuser from the body by removing the two screws 2 Release gear tray by removing the two retaining screws 3 Fix base to the ceiling Use the bezel amp fitting to ensure the cutout is the correct size 4 ISOLATE THE A C SUPPLY and connect unit An unswitched 240V A C supply must be connected to the live L Earth and neutral N terminals on the PCB block On Maintained circuits continuous illumination can be achieved by connecting a link between L and Lsw either locally or through a remote switch 5 Plug battery lead into connector on the PCB 6 Resecure the gear tray into the base of the unit making sure that the mains cable is not trapped by the PCB etc 7 Refit the diffuser using the two screws 8 Operational Check Restore the A C Supply for 30 minutes and then remove The LEDs should illumi nate for at least 10 seconds 9 Restore the A C supply and check that the indicator LED is on ENSURE FITTING IS CHARGED FOR A MINIMUM OF 24 HOURS PRIOR TO TESTING FIRE DETECTION EMERGENCY LIGHTING m NURSE CALL amp DDA EQUIPMENT COMMISSIONING amp MAINTENANCE SERVICES z LIGHTING INDUSTRY FEDERATION ei a nae A BAFE LC EL 555 HA OQR Channel Safety Systems Limited Registered i2. OAN N CT L T 0845 884 7000 Channel Safety Systems Limited F 0845 884 6000 Petersfield Business Park C 1 L E sales channelsafety co uk Bedford Road Petersfield SAFETY SYSTEMS W www channelsafety co uk Hampshire GU32 3QA EMERGENCY LIGHTING LUMINAIRE INSTRUCTIONS amp TEST PROCEDURES LED Flushlight Instructions 11 2011 iss1 RECOMMENDED ROUTINE TEST PROCEDURE The following test is designed to ensure the continued protection of your premises and occupants Because of the possibility of a failure of the normal lighting supply occurring shortly after a period of testing all tests should whenever possible be undertaken at times of least risk e g during daylight hours ONCE A DAY Visual inspection of battery charge led ONCE A MONTH Each unit should be energised from it s battery for adequate time to ensure by simula tion of a failure of the normal lighting supply the emergency mode is functioning correctly ONCE EACH YEAR All units should be placed into emergency mode and checked that the duration provided by the battery meets the specified time period Clean the internal and external surface of the diffuser FIRE DETECTION m EMERGENCY LIGHTING m NURSE CALL amp DDA EQUIPMENT COMMISSIONING amp MAINTENANCE SERVICES LIGHTING INDUSTRY FEDERATION Channel Safety Systems Limited Registered in England No 3853978 VAT Registration No 744 7860 01 Fire Industry Association I OAN N TC L T 0845 88
3. less likely the printed circuit board needs replacing FIRE DETECTION EMERGENCY LIGHTING NURSE CALL amp DDA EQUIPMENT COMMISSIONING amp MAINTENANCE SERVICES LIGHTING INDUSTRY FEDERATION g z H A F 7 Channel Safety Systems Limited Registered in England No 3853978 H F GS QR A 7 gt VAT Registration No 744 7860 01 BAFE PET Maduter System Scheme SP203 Fire Industry Association l Accredited Contractor FM 27737 has grv u
4. n England No 3853978 tAE AS Ze N _ VAT Registration No 744 7860 01 Fire Industry Association Mania aain mre a never amma a i LJ A TC T 0845 884 7000 Channel Safety Systems Limited L TANN L L F 0845 884 6000 Petersfield Business Park E sales channelsafety co uk Bedford Road Petersfield SAFETY SVSTEMS W www channelsafety co uk Hampshire GU32 3QA OPERATION NON MAINTAINED Lamp normally off and battery on automatic charge LED on when A C Supply is healthy Solid state circuitry automatically switches lamp on when A C supply is interrupted MAINTAINED Emergency lamp normally on when the supply to L is switched on The battery is on automatic charge LED on Lamp will switch on or remain on if A C Supply is interrupted MONITORING Green indicator lamp LED normally continuously on Indicator lamp goes out if A C Supply or charger fails BATTERY Sealed Nickel Cadmium rechargeable battery pack TEMPERATURE Performance figures measured at 25 degrees C FAULT FINDING AND CORRECTIVE ACTION MONITORING LED NOT ILLUMINATED A C Supply not healthy Battery not connected Charger failed UNIT NOT MEETING REQUIRED EMERGENCY PERIOD May need cycling Discharge then recharge for 24 hours Re test Battery pack may need replacing if emer gency duration still not met LEDs NOT FULLY ILLUMINATED If the LEDs are not illuminated check connections amp if correct either the battery pack or
Download Pdf Manuals
Related Search