Dimmer – User manual
Contents
1. Dimmer User manual Ordering codes e ZMNHDA2 Frequency range 868 4 MHz CEPT EU China Singapure South e ZMNHDAS Frequency range 921 4 MHz Australia Brazil New Zaeland e ZMNHDA4 Frequency range 908 4 MHz Chile Mexico USA Canada e ZMNHDAS Frequency range 869 0 Mhz Russia e ZMNHDA6 Frequency range 916 0 Mhz Israel This Z Wave module is used for dimming the bulb or to manage the speed of a fan The module can be controlled either through a Z Wave network or through the wall switch The module is designed to be mounted inside a flush mounting box hidden behind a traditional wall switch Module measures power consumption of bulb or fan and supports connection of digital temperature sensor It is designed to act as repeater in order to improve range and stability of Z wave network Supported switches Module supports mono stable and bi stable switches input I1 Installation e Before the installation disconnect power supply e Connect the module according to electrical diagram e Locate the antenna far from metal elements as far as possible e Do not shorten the antenna Danger of electrocution e Module installation requires a great degree of skill and may be performed only by a qualified and licensed electrician e Even when the module is turned off voltage may be present on its terminals Any works on configuration changes related to connection mode or load must be always per2. als Dimensions W x H x D 41 8 x 36 8 x 15 4mm Weight 28g Electricity consumption 0 7W For installation in boxes gt 60mm or 2M Switching MOSFET Trailing edge max 100W mono phase asynchronous fan motor can be connected to dimmer output Description of switch function Switch toggles parameter set to 1 the state of the light bulb between the last dimming value and 0 If last dimming value is 0 then the light is turned 100 when switch changes its state Bulb types which support dimming function e The classical incandescent bulbs e Halogen bulbs operated by 230 V AC High Voltage Halogen e Low voltage halogen bulbs with electronic or conventional transformer e Dimmable compact fluorescent bulb CFL If the bulb at low intensities flushes it is recommended to set parameter 60 minimum dimmable value to 30 or more e Dimmable LED bulbs Z Wave Device Class BASIC_TYPE_ROUTING_SLAVE GENERIC_TYPE_SWITCH_MULTILEVEL SPECIFIC_TYPE_POWER_SWITCH_MULTILEVEL Z Wave Supported Command Classes COMMAND_CLASS_BASIC COMMAND_CLASS_SWITCH_MULTILEVEL_V3 COMMAND_CLASS_SWITCH_ALL COMMAND_CLASS_SWITCH_BINARY COMMAND_CLASS_METER_V3 COMMAND_CLASS_SENSOR_MULTILEVEL_V3 COMMAND_CLASS_MULTI_CHANNEL_V3 COMMAND_CLASS_POWERLEVEL COMMAND_CLASS_ASSOCIATION COMMAND_CLASS_CONFIGURATION COMMAND_CLASS_MANUFACTURER_SPECIFIC COMMAND_CLASS_VERSION COMMAND_CLASS_MARK COMMAND_CLASS_BASIC COMMAND_CLASS_SWITCH_MULTILEVEL_V3 Endpoint 1 12 Dev
3. an Slovenia E mail info qubino com Tel 386 5 335 95 00 Web www qubino com Date 08 12 2014 Document Qubino_Flush dimmer user manual_V6 3_eng
4. formed by disconnected power supply disable the fuse Note Do not connect the module to loads exceeding recommended values Connect the module only in accordance to the below diagrams Improper connections may be dangerous Package contents e Flush dimmer Electrical diagram 230VAC Notes for the diagram N Neutral lead L Live lead Q Output for electrical device 13 Input for switch push button or sensor I2 Input for switch push button or sensor I1 Input for push button switch TS Terminal for digital temperature sensor only for Flush dimmer module compatible digital temperature sensor which must be ordered separately Electrical diagram 24VDC Notes for the diagram N 24VDC L 24VDC Q Output for electrical device 13 Input for switch push button or sensor 12 Input for switch push button or sensor I1 Input for push button switch TS Terminal for digital temperature sensor only for Flush dimmer module compatible digital temperature sensor which must be ordered separately S Service button used to add or remove module from the Z Wave network Module Inclusion Adding to Z Wave network e Connect module to power supply with temperature sensor connected if purchased e bring module within maximum meter 3 feet of the main controller e enable add remove mode on main controller e auto inclusion 30 minutes after connected to power supply or e press
5. ice Class GENERIC_TYPE_SENSOR_BINARY SPECIFIC_TYPE_NOT_USED Command Classes COMMAND_CLASS_SENSOR_BINARY COMMAND_CLASS_BASIC Endpoint 2 13 Device Class GENERIC_TYPE_SENSOR_BINARY SPECIFIC_TYPE_NOT_USED Command Classes COMMAND_CLASS_SENSOR_BINARY COMMAND_CLASS_BASIC This product can be included and operated in any Z Wave network with other Z Wave certified devices from any other manufacturers All constantly powered nodes in the same network will act as repeaters regardless of the vendor in order to increase reliability of the network Important disclaimer Z Wave wireless communication is inherently not always 100 reliable and as such this product should not be used in situations in which life and or valuables are solely dependent on its function Warning Do not dispose of electrical appliances as unsorted municipal waste use separate collection facilities Contact your local government for information regarding the collection systems available If electrical appliances are disposed of in landfills or dumps hazardous substances can leak into the groundwater and get into the food chain damaging your health and well being When replacing old appliances with new once the retailer is legally obligated to take back your old appliance for disposal at least for free of charge This user manual is subject to change and improvement without notice Qubino Goap d o o Nova Gorica Ulica Klementa Juga 007 5250 Solk
6. mum dimming values is set by entered value NOTE The maximum level may not be lower than the minimum level 99 max dimming value is defined by Z Wave multilevel device class Parameter no 65 Dimming time soft on off Set value means time of moving the Dimmer between min and max dimming values by short press of push button 11 or controlled through UI Available configuration parameters data type is 1 Byte DEC e Default value 100 Dimming time between min and max dimming values is 1s e 1 255 10mseconds 2550mseconds 2 55s step is 10mseconds Parameter no 66 Dimming time when key pressed Time of moving the Dimmer between min and max dimming values by continues hold of push button I1 Available configuration parameters data type is 1 Byte DEC e Default value 3 Dimming time between min and max dimming values is 3s e 255 10 mseconds 2550 mseconds 2 55s step is 10 mseconds Technical specifications Power supply 110 230 VAC 10 50 60Hz 24 30VDC Rated load current of AC output 0 85A 230V AC Rated load current of DC output 0 85A 30VDC Output circuit power of AC output resistive load 200W 230VAC Output circuit power of DC output resistive load 21W 24VDC Power measurement accuracy 2W Digital temperature sensor range sensor must be ordered separately 50 125 C Operation temperature 10 40 C Distance up to 30 m indoors depending on building materi
7. ntage set value from 0 100 0 100 Available configuration parameters data type is 1 Byte DEC e default value 5 e 0 Reporting Disabled e 1 100 1 100 Reporting enabled Power report is send push only when actual power in Watts in real time changes for more than set percentage comparing to previous actual power in Watts step is 1 NOTE if power changed is less than 1W the report is not send pushed independent of percentage set Parameter no 42 Power reporting in Watts by time interval Set value means time interval 0 65535 in seconds when power report is send Available configure parameters data type is 2 Byte DEC e default value 300 power report in Watts is send each 300s e 0 Reporting Disabled e 1 65535 1 second 65535 seconds Reporting enabled Power report is send with time interval set by entered value Parameter no 60 Minimum dimming value Available configuration parameters data type is 1 Byte DEC e Default value 1 Minimum dimming value is 1 e 1 98 1 98 step is 1 Minimum dimming values is set by entered value NOTE The maximum level may not be lower than the minimum level 1 min dimming value is defined by Z Wave multilevel device class Parameter no 61 Maximum dimming value Available configuration parameters data type is 1 Byte DEC e Default value 99 Maximum dimming value is 99 e 2 99 2 99 step is 1 Maxi
8. service button S for more than 2 seconds or e press push button I1 three times within 3s 3 times change switch state within 3 seconds Module Exclusion Reset Removing from Z Wave network e Connect module to power supply e bring module within maximum 1 meter 3 feet of the main controller e enable add remove mode on main controller e press service button S for more than 6 seconds or e press push button I1 five times within 3s 5 times change switch state within 3 seconds in the first 60 seconds after the module is connected to the power supply By this function all parameters of the module are set to default values and own ID is deleted If service button S is pressed more than 2 and less than 6 second module is excluded but configuration parameters are not set to default values Association Association enables Flush dimmer module to transfer commands inside Z Wave network directly without main controller to other Z Wave modules Associated Groups Group 1 multilevel triggered at changes of state value of the Flush dimmer up to 16 nodes Group 2 basic on off triggered at change of the input I2 state and reflecting its state up to 16 nodes Group 3 basic on off triggered at change of the input I3 state and reflecting its state up to 16 nodes Group 4 default reporting group reserved for the main controller Configuration parameters Parameter no 1 Input 1 switch type Available configuration parameters data
9. type is 1 Byte DEC e default value 0 e 0 mono stable switch type push button e bi stable switch type Parameter no 2 Input 2 contact type Available configuration parameters data type is 1 Byte DEC e default value 0 e 0 NO normally open input type e 1 NC normally close input type Parameter no 3 Input 3 contact type Available configuration parameters data type is 1 Byte DEC e default value 0 e 0 NO normally open input type e 1 NC normally close input type Parameter no 10 Activate deactivate functions ALL ON ALL OFF Available configuration parameters data type is 1 Byte DEC e default value 255 e 255 ALL ON active ALL OFF active 0 ALL ON is not active ALL OFF is not active e 1 ALL ON is not active ALL OFF active e 2 ALL ON active ALL OFF is not active Dimmer module responds to commands ALL ON ALL OFF that may be sent by the main controller or by other controller belonging to the system Parameter no 30 Saving the state of the device after a power failure Available configuration parameters data type is 1 Byte DEC e default value 0 e 0 Flush dimmer module saves its state before power failure it returns to the last position saved before a power failure e Flush dimmer module does not save the state after a power failure it returns to off position Parameter no 40 Power reporting in Watts on power change Set value means perce
Download Pdf Manuals
Related Search