Installation Manual
Contents
1. box or enclosure to prevent tampering This can be connected to an alarm system Fault finding amp FAQs Q The unit will not power up No LEDs on A Check power supply voltage is within 11 5V 12 5V DC Q The unit powers up but there is a bleeping from the door station A This means the unit is not able to detect the network for some reason Check the SIM card is activated and has calling credit Power off the unit remove the SIM and check it in a mobile phone to verify it can make a call Check the SIM does not ask for a PIN code when put in a phone If it does then disable the PIN code request Check the SIM is a standard GSM SIM not 3G or 4G only SIM If you are unsure contact your SIM card provider to verify Frequency of operation should be any one of the international quad band standards 850 900 1800 1900 MHz Check the reception is good Poor reception is not sufficient Check the antenna has been mounted as high as possible not near large metal objects or wet green shrubs etc Check the antenna connection Visually inspect that the centre pin inside the antenna is intact and has not been pushed back inside the fitting Q The unit calls the first number but there is not enough time to answer before it diverts to the next number A Increase the no answer time as per programming instructions Q The unit calls the first number but voicemail comes on before it can ring the second number A Decrease the no a2. t a 552 2 Max monitoring time for listen in mode when calling the intercom join insert the SIM and slide in the 572 2 Unit can call or SMS service number by set duration to prevent CLOSED direction to lock it in sla SIM card deactivation if seldom used 00 60 days 00 no inform place Do NOT Force or use a 58 Choose between scheduled call to service number or send SMS to screwdriver service number 1 for SMS 2 for call Store service number to receive scheduled SMS or call from 1 10 After a final check of lla HEV OUM DUL wiring switch on the C g power Keypad Connections TT Delete service number N N A N A N A ABK model Dial in mode for withheld numbers or non stored numbers 1 i 9 j 11 Allow 20 30 seconds for the unit to boot up and detect the network 65 PRE an T eee Once successful connection has been made the unit will sound a 29 i 13 Delete phone number for caller ID access confirmation tone and the GSM LED will begin flashing If there is a fault or problem the unit will emit a series of bleeps or warning Delete all phone numbers for caller ID access p NA tones If this occurs check 1 That the SIM card has been activated and has credit 999 Restore defaults 2 That the SIM card does not require a PIN code disable this ina phone aL Check stored numbers Note no pass code needed for this N A 3 That the SIM card can make and received a call on a phone command O dial out nu
3. ae Installation Manual Programming Programming is best done by SMS text It can also be done by DTMF from a normal telephone Installation 1 Before you install this equipment please read this full manual 2 Ensure that there is good network reception at the location where it will be installed 1 First check reception Send the following SMS to the unit 20 The unit should reply SIGNAL LEVEL POTONE 3 Remove the top two security Where will be between 1 and 31 UNIOON screws as shown Do NOT remove Below 14 can cause problems with relay T Aa Call Button the bottom screws operation or no voice from the gate to the 1 12 13 20 21 31 house Take action to improve reception Poor Medium Good The front door will hinge downwards Optional keypad to allow access for mounting holes 2 Program the numbers you wish the unit to dial when the call button is module and connection terminals pressed up to a maximum of 3 numbers Each SMS must start with the pass code default 1234 in the following format 12 1234 followed immediately Note The protective film on the front by a command E g to program the telephone number 0987654321 enter of the intercom should not be removed the following SMS until fully installed Up to 3 numbers can be sent together in a single SMS as 12 1234 110987654321 Mllows PIngE dropt dgan 4 Use appropriate wall fixings 8 12 1234 11tel number1 12tel number2 13tel number3 10mm
4. anchors 75mm deep with M5 11 Telephone number 1 ae screw are recommended a har ee 12 Telephone numbers aai 13 Telephone number 3 minimum 3 It is recommended to change the no answer time if there is more than 1 5 Install the antenna as high as number stored This stops the unit ringing a number after a set time and can possible on the top of the pillar to be used to prevent voicemail answering the call Send the following SMS Speech ensure line of sight in all directions for 12 1234 52 Where can be 2 digits from 10 99 seconds default is 20 Writ best possible reception my The unit can allow up to 100 telephone numbers to be stored for users to Keep antenna high as possible and be able to ring the system for automatic entry This uses caller ID like a above electronics audio equipment phone to determine the identity of the caller First the unit must know what 4 5 feet to eliminate interference country it is operating in minimum Entrance Pillar 4 Program the country code as follows 4 ox Where can be 1 3 digits For uk insert 44 for Ireland 353 for Side View 12 1234 712 2 USA insert 1 Do not use any leading zeros Wiring O ATENE 5 Enter the telephone numbers required to have access control Do not enter Finger tighten only 6 Carefully follow the country code just the complete number as you would dial it wiring instructions Up to 3 numbers can be sent togethe
5. de 5555 operating relay 2 2 9 a eleik Ls ists isl ca Group 2 Add code Location 31 Pin code 5555 Validate 5 10 relay1 mat Spat Be 20 relay2 Delete code ID location to be deleted Validate 30 relay3 1 Delete a code i Delete all codes in a grou e se 9 e 10 relay1 group 20 relay2 group 30 relay3 group Super delete code Validate Programming Relay output times amp modes fo 1 9 s 9 9 9 51 relay1 0 start stop toggle mode latching 52 relay2 1 99999 seconds momentary operation 53 relay3 Validate Programming SUPER user code Super user code is an optional feature which allows the same code to operate outputs 1 2 or 3 e e Location 4 8 digit code Validate Using super user code Using standard user code To use standard code simply enter the 4 digit code Note Remember to exit programming mode with before testing user codes Restoring defaults While in programming mode enter the following to delete all codes and settings apart from the Master code this can take up to 2 5 minutes e Le e Le When the master code is forgotten 1 Wire a push button or replicate with wire link across the EG IN terminal and GND 2 Switch off power for 1 minute 3 Switch ON power 4 during the first 60 seconds press the EG button once to enable the function 5 Enter the following code Lelle i CC The keypad should
6. ending on manufacturer Default pass code 5678 is shown in all examples This may have been changed by your installer Trigger Gate Latch or hold Unlatch Door open gate door gate door SEND SMS SEND SMS SEND SMS 33 56 8 34 56 8 35 56 8 ul a ieee e HOLD OPEN FEATURE OR PARTY MODE Some gate systems allow hold open control depending on 2 3 manufacturer Send the following SMS commands to control the gates Calling the intercom options Dialling MY GATE u END n Option 1 If your number is saved inside the intercom memory just dial it and it will activate the door or gate without answering your call The intercom will end the call for you If limit switch fitted Check stored check gate status numbers SEND SMS SEND SMS DOH 21 Reply will indicate O dial out number opened or closed Dial in number for caller ID access 33 5678 1P F S 6 aa e O Option 2 If your number is not saved in the intercom memory it will answer the call Enter the code on your telephone keypad to activate the door or gate default code shown
7. gh enough Try earthling the speech panel chassis to OV of the power supply This is also a symptom of poor reception Try above steps on checking and improving reception Q The or key does not work when the intercom calls a phone A Check if you can hear the relay clicking at the gate when the or key is pressed during a call If it can be heard then the system is working check wiring between the relay and the lock or gate panel If the relays do not make a clicking sound then check this feature on a different mobile cell phone or landline If it works on a different phone check the settings on the phone in question under DTMF tones Failure of DTMF tones to operate correctly is also a symptom of low reception Check steps above on improving reception Try pressing the buttons longer when attempting to activate the gates or door User Manual For GSM 3AB GSM 3ABK Wireless Intercom This GSM intercom system will call up to 3 telephone numbers in sequence when the call button is pressed There are several modes of operation depending on how the unit has been programmed by your installer The following instructions will assume default programming Intercom calling your phone My Gate Call button CALLING pressed ANSWER DECLINE x Answer call Sending SMS Commands Press to open OR Press to hold open and Press 1 to release again Only some gate systems allow hold open control dep
8. mber Dial in number 4 If the SIM card was purchased with a phone that it is not locked to that Remember to begin each new SMS with pass code 12 1234 phone Call the network operator to check Note DTMF Programming is done by calling the unit amp entering the pass code first then after a 5 Switch off power remove and reseat the SIM card and try again long single confirm tone commands can be entered A fault is indicated by 3 short bleeps Keypad Programming only ABK models LED indicators ON when incorrect codes entered and outputs are locked out GREEN when output 1 activated RED when output 2 activated JU LU UL Fast FLASHING wrong code entered error LN LTL SLOW FLASHING in normal standby mode L ON in programming mode L ON when relay 3 activated Note Programming can only begin 60 seconds after power on Enter Programming mode The unit is now in programming mode Amber LED x will remain ON 0000 is default programmers code Note Pressing again will exit programming mode Enter new programmers code a Location 4 8 digit code Validate Record or Delete user codes Lo o Lo Lo a 10 relay 1 codes 2 add code Memory locations 1000 available 5 delete code 000 999 for relay 1 20 relay 2 codes 001 100 for relay 2 100 available 001 100 for relay 3 30 relay 3 codes 100 available Pin code 4 8 digits Validate Example Add user 31 to have access co
9. now be in programming mode ready to accept new data Additional keypad information Note These features are not commonly used EG IN EGRESS INPUT Connect a push button between this terminal and GND When Egress button is pressed output 1 will be activated for the programmed delay Egress button is usually located inside a building and used as a push to exit K or A KEYPAD ACTIVE OUTPUT An NPN transistor open collector output It switches to ground for 10 seconds on each key touching This can be used to turn on lights CCTV camera or buzzer to notify a guard The rating of this output is lc max 100mA sink Vc max 24VDC DU OUT DURESS OUTPUT An NPN transistor open collector output It switches to ground after the Duress Code is entered Use it to trigger an alarm zone or turn on a buzzer to notify a guard Ic max 100mA sink Vc max 24VDC DOOR SENSE N C connected to GND to be connected to a normally closed door contact It can be used to generate a door open alarm or door forced open alarm O P 1 Inhibit Normally open When closed this disables all codes for relay group 1 except super user and duress codes Interlock Output NPN transistor output open collector max power 24v dc 100mA sink Used to operate a door in conjunction with another keypad or prevent two doors being opened at the same time Tamper N C Normally closed tamper switch This can be used in conjunction with a tamper switch on a
10. nswer time as per programming instructions Q The caller ID part does not work A Be sure to program the caller ID part under 72 feature If your number is a private or number withheld then it will not work Even if you have already programmed a number to receive a call from the intercom if you also want that number to have caller ID access it must be programmed under the 72 feature also Ensure the number is entered as you would normally dial it from another phone Do not put the country code in front of the number Enter the country code in which the unit is operating in separate under the 71 feature International callers ringing the intercom may not work Q There is no audio from the gate but the person at the gate can hear ok A This can be due to low reception Check reception level by 20 Change SIM card if necessary to another network which may have better coverage Purchase a high gain antenna This may also be caused by either a defective microphone or incorrect microphone wiring or a short circuit by whiskers between the centre core and the shielding or excessive microphone cable length Q The audio quality that can be heard on the remote telephone is poor or humming buzzing A A small amount of GSM buzz can be considered normal on GSM intercoms but not so much that causes inability to hear the person speaking This can be caused by the GSM antenna being mounted too close to the speech panel or not mounted hi
11. r in the same SMS Just Power LED f 1g i 12 1234 720987654321 add 72 then the number then each time The pass code only Additional wiring needs to be put at the beginning of each new messge GSM LED suggestions for electric USA customers Enter the numbers with the long distance 1 before area code then the number JUN strike lock and magnetic E g 1 702 555 1234 n as lock are shown overleaf Additional Programming Parameters Network found Code Description Default CPU LED SIM card annan holder S M card 0127727 Change programming password tanaby Busy 7 Register your SIM card 02277 2 Change access control password allows users not in caller ID list 5678 om to call intercom and use pass code to activate relay with the network and check a it works in a mobile phone 03 2 Change monitoring mode password dial to listen in mode first If you are using a Pre O6e o l Opinna pay or Pay amp Go SIM it will Delete a button calling number where n number 1 2 or 3 mezgil input limit od SS SiMchodibeGsM e a S switch 3 Speaker volume Where level 0 4 Output rom gate SIM should be GSM i xit button compatible Microphone volume Where level 0 4 Tamper INT Lock P N C 8 Ensure the power IS OFF 51 Relay time Where 1 9999 seconds before inserting the SIM card 53 Max call time Where 005 999 seconds 3 digit code Sense OAND 9 Carefully slide the SIM DU out ale ully slide
Download Pdf Manuals
Related Search