INSTALLATION MANUAL
Contents
1. 1000 Y 98 0 0 3 98 0 0 1 105 0 0 0 900 500 ALL_ROTATE 55 5 EXECUTE Successfully Finished e o 0 FESTSIMULATION NO 50 22 AUTO ADJUSTMENT OF REGISTRATION amp DRUM POSITION NOW EXECUTING EXECUTE Error occurs a FESTSIMULATION NO 50 22 CLOSE AUTO ADJUSTMENT OF REGISTRATION amp DRUM POSITION PRESS ECEXUTE TO START ERROR TONNER EMPTY 01 EXECUTE 2 When the adjustment is completed EXECUTE key returns to the normal display and the value of the adjustment result is dis played The current skew level for each color is displayed on the SKEW display section TESTS MULATION NO 50 22 CLOSE AUTO ADJUSTMENT OF REGISTRATION amp DRUM POSITION MAIN F MAIN R SUB SKEW PHASE C 105 0 0 2 110 0 0 1 103 0 0 4 500 1200 1 7 M 100 0 0 0 99 0 0 2 99 0 0 2 800 1000 Y 98 0 0 3 98 0 0 1 105 0 0 0 900 500 ALL_ROTATE 55 5 EXECUTE 3 Make test print in the simulation mode for checking whether the void off center and printing quality are correct If the test results are not correct refer to 5 ADJUSTMENT from the Service Manual and perform the adjustments Void SIM50 01 50 10 Printing position SIM50 10 Off center Registration SIM50 20 When the result of the void and the printing position are not suitable perform ADJ4 by referring the 5 ADJUSTMENT of the Service Manual When the result of the off center is not2. adequate perform ADJ5 by referring the 5 ADJUSTMENT of the Service Man ual Printing quality SIM64 5 When the result of the print quality is not good perform ADJ10 by referring the 5 ADJUSTMENT of the Service Manual MX C301 MX C301 C301W MAIN UNIT 2 4
3. earth band to your arm and connect it to the machine When repairing or replacing an electronic part perform the pro cedure on an anti static mat G Note for proper drum developing fusing and transfer unit handling When handling the OPC drum developing fusing units and transfer units observe the following items Drum unit To prevent damage to the OPC drum avoid working on the drum unit in high intensity light areas When the OPC drum is removed from the machine cover it with light blocking material When using paper use about 10 sheets of paper to cover it Be careful not to attach fingerprints oil grease or other foreign material on the OPC drum surface Transfer unit Be careful not to leave fingerprints oil grease or other foreign material on the transfer roller primary transfer belt and secondary transfer roller Developing unit Be careful not to leave fingerprints oil grease or other foreign material on the developing unit Fusing unit Be careful not to leave fingerprints oil grease or other foreign material on the fusing roller If the machine is not going to be used for an extended period release the pressure on the fusing rollers If these items are neglected a trouble may be generated in the copy and print image quality 2 Transit and delivery No Content 1 Implements facil Use a forklift If no forklift is available ity and man power m
4. SHARP INSTALLATION MANUAL DIGITAL FULL COLOR MULTIFUNCTIONAL SYSTEM Parts marked with are important for maintaining the safety of the set Be sure to replace these parts with specified ones for maintaining the safety and performance of the set SSS SS SS SSS SSS a This document has been published to be used SHARP CO RPO RATION for after sales service only The contents are subject to change without notice Machine Environment Installation and Transportation 1 Machine Environment and Installation Before installing the machine check that the following conditions are satisfied If the installing use conditions are not satisfied the machine may not exhibit full performance resulting in problems It may also cause safety problems Using the following information make sure all aspects of installation space power transportation leveling and safety are met Transportation space Installing space Power source Capacity fluctuation safety Floor strength Direct rays of the sun dust temperature humidity gases chemicals A Transportation space For installation of a large size machine be sure to check that the door size is wide enough before bringing in B Installing space The following space must be provided around the machine in order to assure machine performance and proper operations If any option is installed provide the additional space for with installa tio
5. The telephone cable does not come with the machine When connecting the line cable to LINE or TEL wind the line cable two turns around the included ferrite core as shown in the fig ure and connect to the modular jack which is marked with LINE MX C301 MX C301 C301W MAIN UNIT 2 3 G Specifications setting Use SIM26 to set to the specifications according to the customer s request SIMNo Content 26 6 Destination setting To customize one of the following items after destination setting change the set value of the item Content Toner save mode enable disable setting 18 For the other destinations this setting is made by the user program 26 3 Image quality check A Execution items Execute the checking items about the printing quality Regarding the specific procedures for the printing quality refer to the Service Manual 5 ADJUSTMENT B Description 1 Print engine image distortion confirmation and adjustment This adjustment performs the print engine image distortion adjust ment the OPC drum phase adjustment and the color registration adjustment simultaneously 1 Enter SIM50 22 mode and perform the auto registration adjust ment by pressing EXECUTE key FRSTSIMULATION NO 50 22 AUTO ADJUSTMENT OF REGISTRATION amp DRUM POSITION MAIN F MAIN R SUB SKEW PHASE C 105 0 0 2 110 0 0 1 103 0 0 4 500 1200 1 7 M 100 0 0 0 99 0 0 2 99 0 0 2 800
6. anpower of two persons is required Transit must be made in packed condi tion A lmplements facility and manpower It is recommended to use a forklift when moving the machine If no forklift is available man power of two persons is required The machine is considerably heavy and requires safety precautions for delivery and installation Transit of the machine must be made in packed condition to the install ing place B Delivery Remove the packing materials prior to installation in the office environ ment Machine Environment Installation and Transportation ii 2 MX C301 C301W MAIN UNIT 1 Unpacking A Unpacking procedure 1 Open the top of the carton box 2 Remove the parts included in the package 3 Remove the main unit from the package and remove the poly ethylene bag Place the machine on a solid sturdy surface Be sure not to hold the scanner unit to lift up the main unit B Removal of the fixing tape and protection mate rial With only for north America model remove the warning sheet C Check the packed items 1 Check that all the parts are in the package No Packed part names Quantity 1 piece for each color TONGE CATMOIE Other than North America 200V series only 1 piece i200 08 3 Operation Manual 4 2 Installation A Remove the cap from developing unit 1 Remove the tray MX C301 MX C301 C301W MAIN UNIT 2 1 2 Open the front cover MASA
7. l wave ith it J il 1h it wi TF H ea J ae A NOTE Be sure to keep the caps Caps are used when the machine is transferred to the different location B Scanner lock release 1 Remove the optical unit fixing screw and the red label C Installation of toner cartridges The life of each toner cartridge is as follows Black toner cartridge equivalent to approximately 1K A4 LT 5 Color toner cartridge equivalent to approximately 1K A4 LT 5 1 Shake the toner cartridge included in package vertically sev eral times 90 2 Insert the toner cartridge horizontally and straight until it locks NOTE Be sure to install the color cartridges to their proper posi tions Avoid installation to a different color position NOTE Do not forcibly insert the toner cartridge Keep holding the cartridge and completely insert it NOTE When the machine is transported with the developing unit removed be sure to remove the toner cartridge if not toner may become clogged NOTE Do not remove or insert the toner cartridge with the devel oper cartridge removed NOTE Press the center of the cartridge until it is locked when installing the cartridge MX C301 MX C301 C301W MAIN UNIT 2 2 D Fusing unit lever 1 Open the right door unit 2 Turn the levers of the Fusing unit to add the pressure Only the levers can add or release the pressure There is no
8. machine has proper ventilation Humidity RH 85 60 20 10 C 30 C 35 C Machine Environment Installation and Transportation i Operational environment Temperature 10 to 35 degree C Humidity 20 to 85 RH Atmospheric pressure 590 to 1013hPa altitude O to 2000 m 2 Contaminates If dust enters the machine it may cause dirty copy and a paper jam resulting in a shortened lifetime 3 Direct sunlight If the machine is installed in direct sunlight the exterior of the machine may be discolored and abnormal copies may be produced 4 Gases and chemicals Do not install the machine at a place where there are gases and chem icals Especially be careful to avoid installation near a diazo type copier which produces ammonium gas Copy quality may be adversely affected and machine problems may arise 5 Vibration Avoid installation near a machine which produces vibrations If vibrations are applied to the copier machine copy images may be deflected and a trouble may be caused F Note for handling PWB and electronic parts When handling the PWB and the electronic parts be sure to observe the following precautions in order to prevent against damage by static electricity When in transit or storing put the parts in an anti static bag or an anti static case and do not touch them with bare hands When and after removing the parts from an anti static bag case use an earth band as shown below Putan
9. n Adequate space must be provide behind the machine for proper venti lation of heat and dust The machine will not function properly if heat and dust cannot be properly expelled from the machine 30 cm 30 cm 45 cm C Power source Capacity voltage frequency safety plug If the power specifications are not satisfied the machine cannot exhibit full with performance and may cause safety trouble Strictly observe the following specifications 1 Power capacity Check that the following power capacity is satisfied If not additionally provide a proper power source Current capacity Japan 20A or more EX 100V 15A or more EX 200V 10A or more Check the shape of the power plug of the machine and insert it into a power outlet of the acceptable shape 2 Power voltage Measure the voltage during copying to check that the voltage is in the range of the specified voltage 10 If the voltage is outside the specified range please have a certified electrician upgrade the outlet Electrical work is required Use of a step up transformer is also available In this case the capac ity must be great enough for the max power consumption of the machine 3 Power frequency waveform The frequency must be within the range of the specified frequency 2 If the power waveform is improper a problem may occur with the machine 4 Safety Be sure to properly ground the machine Groundi
10. ng earth connection must be performed before inserting the power plug into the power outlet When disconnecting the earth connection be sure to disconnect the power plug from the power outlet in advance 5 Power plug Check the shape of the power plug of the machine and insert it into a power outlet of the acceptable shape Power plug stated in power capacity D Floor strength and level This machine is considerably heavy and becomes heavier with an option installed The floor must be strong enough to safely support the weight of the machine as well as any installed options If the unit is not properly leveled toner density may become affected degrading the copy print quality Also color shift or image distortion may occur To assure proper Image quality make sure the machine is sitting level E Direct rays of the sun dust temperature humid ity gasses chemicals vibration 1 Temperature and humidity Environmental conditions This machine is designed to perform properly under the specified tem perature and humidity If the temperature and humidity exceeds the specified range the machine may not operate properly and or cause equipment failure Especially when the humidity is too high paper absorbs humidity to Cause a paper jam or dirty copy Do not install the machine near a heater an air conditioning outlet or a humidifier Condensation may form inside the machine causing multiple prob lems Make sure
11. screw for adding or releasing the pressure Sts H Fa Tg EE TEE NA epee See J L i m lam A PE O C O NOTE When the machine is left for one month without using the Fusing heat roller could be deformed If the machine is not going to be used for an extended period release the pres sure on the fusing rollers E Tray size setup 1 Gently pull out the tray until it stops If paper is in the tray remove it 2 Adjust the guide plates A and B to the vertical size and the hori zontal size of paper The guide plates A and B are movable Hold the fixing knob to slide the guide plates A and B to match the paper size gt 7 Plate B 3 Insert the tray slowly Plate A 4 Touch the Paper Select key Then select the tray that the customer wants to use by touching the key of the desired tray Full Color 2 Sided Copy Exposure l Auto Copy Ratio 100 Paper Select Paper Tray Bypass Tray Pl orli Plain 2 84x11 el Plain H a11 mi Plain F Line cable connection Only for the machine with FAX 1 Connect the telephone line to the modular jack indicated as LINE It is necessary to prepare the line cable by yourself
Download Pdf Manuals
Related Search